Search Documents

By Marcus A. Wiley, Gregory Abramov

Borehole mining (BHM) is a remotely operated method of extracting rock material through boreholes by high-pressure water jets. Figure 1 illustrates a BHM tool and fluids circulation. The tool consists of at least two pipes, one for pumping down high-pressure water, the second for delivering slurry to the surface. This article reviews the BHM process. It discusses current and new applications for borehole mining and help the readers determine if BHM is applicable in their situations. Previous articles in ME about BHM explained either a particular project (ME, April 2001, pp. 33-36) or a newest patent in this area (ME, March 1991, pp. 313-318). However, neither one provided an overview on the modern BHM technology.

Jan 1, 2004

By G. Stuart Jenkins

Conditions at the properties of the Consolidated Coal Co. had reached a point where improvements were almost impractical. The mines, sunk years ago, had shafts and entries so small as to preclude the use of large mine cars. A radical change was necessary in the type of mining and also in the type of mine to accommodate such haulage units. After due consideration, the company decided to enter the field of trackless mining, utilizing belt conveyors and chain-flight conveyors, the belt conveyors to take the long haul, and the chain-flight conveyors to be used for gathering. It was decided not to sink a shaft, hut to drive a slope on an inclination of 17½°, which the company believes to be about the limit on which coal can be carried on a belt without rolling back unduly. Sinking the Slope It was decided, in sinking the slope, to make an opencut until rock was reached, which was some 65 ft. below the surface, and then to drive the slope through an inclined tunnel from that point. In making the open-cut, the schedule called for the removal of about 25,000 cu. yd. of clay, holding the banks on an inclination of one and a half to one, the thought being to make this cut in a minimum of time, put in a reinforced concrete slope, and then back-fill. Difficulty was experienced because the clay was of a sort that was called "subsiding base" material by contractors visiting the job. In other words, a "squeeze" occurred, the pressure causing the floor of the cut to move up just as it does in many mines where the coal is underlain by thick fire clay and inadequate pillars have been left. It was necessary to move the waste banks back from the edge of the cut 700 or 800 ft., and even then the floor could not be controlled, the result being that almost 100,000 cu. yd. of clay was handled before the rock was reached. A concrete slope was then rapidly constructed, using 95 tons of special-shaped reinforcing iron. The floor of this slope was made 30 in. thick at the bottom, and 17 in. thick at the top, the sidewalls being 18 in.

Jan 1, 1940

By G. Stuart Jenkins

Conditions at the properties of the Consolidated Coal Co. had reached a point where improvements were almost impractical. The mines, sunk years ago, had shafts and entries so small as to preclude the use of large mine cars. A radical change was necessary in the type of mining and also in the type of mine to accommodate such haulage units. After due consideration, the company decided to enter the field of trackless mining, utilizing belt conveyors and chain-flight conveyors, the belt conveyors to take the long haul, and the chain-flight conveyors to be used for gathering. It was decided not to sink a shaft, hut to drive a slope on an inclination of 17½°, which the company believes to be about the limit on which coal can be carried on a belt without rolling back unduly. Sinking the Slope It was decided, in sinking the slope, to make an opencut until rock was reached, which was some 65 ft. below the surface, and then to drive the slope through an inclined tunnel from that point. In making the open-cut, the schedule called for the removal of about 25,000 cu. yd. of clay, holding the banks on an inclination of one and a half to one, the thought being to make this cut in a minimum of time, put in a reinforced concrete slope, and then back-fill. Difficulty was experienced because the clay was of a sort that was called "subsiding base" material by contractors visiting the job. In other words, a "squeeze" occurred, the pressure causing the floor of the cut to move up just as it does in many mines where the coal is underlain by thick fire clay and inadequate pillars have been left. It was necessary to move the waste banks back from the edge of the cut 700 or 800 ft., and even then the floor could not be controlled, the result being that almost 100,000 cu. yd. of clay was handled before the rock was reached. A concrete slope was then rapidly constructed, using 95 tons of special-shaped reinforcing iron. The floor of this slope was made 30 in. thick at the bottom, and 17 in. thick at the top, the sidewalls being 18 in.

Jan 1, 1940

Discussion of the paper of CHARLES H. MACDOWELL, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 103 to 114. GEORGE S. RICE, Pittsburgh, Pa.-I am especially interested in the mining side of this important question. In 1911, when in Europe investigating mining matters, giving special attention to subsidence clue to mining, for there is a very big problem of that kind, as many of you know, in the Pennsylvania anthracite region, I visited Stassfurt, which is one of the chief centers of potash mining, and which was pointed out as the place to see surface subsidence. We found the town much askewsome of the streets having sunk from 15 to 30 ft., leaving many ancient buildings pitching at various angles. One old church, 500 or 600 years old, has been sunk about 20 ft., cracking it badly. I understand that this condition came about because in early mining clays they were careless about leaving proper supports and used no filling or packing. The Stassfurt mines work along a buried anticline the sides of which pitch at 45° on the average. Through this careless mining they had a break of the hanging wall which let in water from the overlying marls and sands. The water rapidly dissolved the salts in the pillars, and spreading through the entire chain of mines, caused their complete loss, with serious trouble for the old city. They had to start new mines some distance away, and take care to prevent roof caves. The packing system is of interest. They were driving large rooms into the rock-salt foot wall and using the rock salt as dry filling. The application of hydraulic filling, using a saturated solution, was under contemplation at some plant nearby. Whether 6r not the plan was carried out I do not know. I was reminded of the plan by Mr. MacDowell's remarking on the use of a saturated salt solution in the core drilling. His reference to the apparent breakdown of the potash syndicate raises an interesting question. We have had the German system of syndicates pointed out as perhaps one means of solving our troubles in the soft-coal mining industry due to overproduction. It seems to have worked out admirably in the case of the Westphalian coal-mining syndicate and also in the syndicate of Upper Silesia; but apparently the syndicate plan did not work in the potash industry. .

Jan 5, 1915

By J. B. Winter

The present Inspiration Consolidated Copper Company Smelter/Acid Plant complex located near Miami, Arizona, was designed and built specifically to conform to the ambient air quality standards imposed by the Federal Clean Air Act of 1971. The present plant replaced a facility which had been in operation since 1915. The electric furnace, siphon converters and acid plant complex were commissioned in May, 1974 (1). At that time, the Plant was considered to be one of the most extensively monitored and instrumented facilities of its kind in the world. Several control areas were located in close proximity to the controlled process, in addition to so-called central control rooms in the Smelter and Acid Plant. The control rooms were staffed with officials below the foreman level. Instrumentation consisted of conventional analog devices, except for a computer used in monitoring ambient air environmental conditions and limited use of programmable logic controllers. The harsh service conditions prevalent in the plant rendered a significant portion of the instrumentation unreliable and, in many cases, inoperable. Failure of the facility to obtain the total sulfur collection for which it was designed was, in part, due to serious inadequacies in control system logic and sulfur recovery averaged 79% in the early years. After careful study of the smelting process, engineering hardware and high labor cost inherent in the organizational structure, management made a judgement decision to convert to centralized control of the process with high level supervision 24 hours per day. A distributed digital control system with supervisory arid data acquisition/information reporting computers was selected to satisfy the requirement of central control. Operations are now controlled and coordinated from a primary control room in the Smelter and a satellite control area in the Acid Plant.

Jan 1, 1983

By Emöke Imre

A point-symmetrical linear coupled consolidation model with displacement boundary condition is suggested for the description of the consolidation around the pile tip after pile penetration. Analytical solution is given. Main features of the solutions are predicted by the analysis of the system of differential equations and, the boundary conditions.

Jan 1, 2002

Bailey, Lewis Newton, Master Engineer, Senior Grade, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia at Camp Merritt, N. J., on April 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on October 7, 1915. Dougall, Ralph, killed in action. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M., killed in action on October 12, 1917. Gorman, Thomas C., Lieut., Canadian Engineers, killed in France, Mar. 18, 1918. Hague, William, 1st Lieut., Engineer Officers' Reserve Corps, died in active service. Hall, William T., Capt., Royal Flying Corps, killed in action. Heine, Bernhardt E., Lieut., Aviation Service, killed at Fort Sill, Okla., Aug. 10, 1918. Irving, John Duer, Capt., 11th Engineers, A. E. F., died while on active service in France on July 26, 1918.

Jan 9, 1918

By Sudhir Kumar Kashyap

In underground activities ground control is a challenging problem. It affects safety, production, and efficiency. As per statistics of accident data, ?fall of roof/sides? is one of the major causes of mine accidents. In many cases, our experiences and understanding of soil and rock behavior still fall short of being able to predict how the ground will behave. Presently, empirical approaches to design are widely used in estimating mine support parameters. Under these circumstances, expert judgment plays an important role, and such accidents can be obviated with accurate measurement and optimization of data and analysis using the neuro-fuzzy technique of artificial intelligence. Recently, a neuro-fuzzy hybrid approach has become one of the major areas of interest in engineering fields because it gets the benefits of neural networks as well as those of fuzzy logic systems, and it removes the individual disadvantages by combining them on the common features. Neural network and fuzzy logic technologies have common features, such as a distributed representation of knowledge, the ability to handle data with uncertainty and imprecision, etc., like in ground control. Fuzzy logic technique has tolerance for imprecision of data, while neural networks have tolerance for noisy data. In this paper we have focused an intelligent technique, i.e., neuro-fuzzy technique, to approximate the setting load given to the standing support (props) erected for the purpose of supporting freshly exposed roof during underground mining. We have used twelve input variables of rock parameters, and after having trained using a neural network with a sigmoidal function as an activation function, simulation was done to find the output parameter, i.e., the pre-load (setting load)to be applied on props. Outputs of the neural network were again fed to the fuzzy system together with the twelve parameters, incorporating five triangular membership functions for each parameter. Final optimum output was approximated using the MATLAB program, which was found to be satisfactory. Neuro-fuzzy technique has better performance over individual neural networks or fuzzy logic technique.

Jan 1, 2012

By Lucas Sanches Magalhães

A utilização de resíduos industriais é dificultada, na maioria das vezes, pela presença de determinados elementos, como por exemplo, o ferro, justificando assim a sua remoção. Dentro deste contexto, o objetivo deste trabalho foi estudar a sulfatação de um resíduo proveniente da flotação de um minério de ferro e subsequente lixiviação deste resíduo sulfatado. A composição mineralógica da amostra inicial foi obtida por DRX e MEV sendo possível identificar quartzo (SiO2), hematita (Fe2O3) e muscovita (KAl2Si3AlO10(OH,F)2). De acordo com a análise química, os teores dos elementos principais foram: Fe (12,65%), S (4,02%), e Al (0,62%). Na sulfatação, realizada à 250ºC durante 4 horas, foi estudada a influência da relação ácido sulfúrico/amostra (0,1:1; 0,2:1; 0,7:1; 0,8:1; 0,9:1 e 1:1) na extração do ferro. A lixiviação foi conduzida com 5% de sólidos do material sulfatado, sendo avaliada a interferência da temperatura de lixiviação (25°C e 90°C) e do tempo de duração dos ensaios (15min, 30min, 60min, 120min, 180min e 240min). Pelos resultados obtidos observou-se que o tempo de lixiviação foi um parâmetro insignificante. A máxima extração de ferro foi encontrada sulfatando o resíduo na relação ácido/amostra 1:1 e posteriormente realizando a lixiviação deste resíduo sulfatado a 90°C por 30 minutos, alcançando 85,64% de extração do Fe.

Aug 17, 2017

By Wesley T. Holmes

This report describes the second phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected synthetic slag compositions in the Ti02 -A1203 -FeO-Si02 -CaO-MgO system. Both the hot-stage microscope and the strip furnace (melting-holding-quenching technique) were used during test procedure to determine the effects of CaO, MgO, and SiO2 on the liquidus temperature of slags. The liquidus temperatures of slags studied ranged from 1,241° to 1,900° C. The lowest liquidus temperature for each Ti02 plus A1203 plus FeO weight-percent generally occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. In this investigation substitution of either CaO or MgO for SiO2 and MgO for CaO raised the liquidus temperature of more than 50 percent of the reported base slags when Ti02, A1203, and FeO contents were held constant. The results of this investigation may serve as guidelines for determining flux requirements in smelting a wide variety of titaniferous magnetite concentrates or ores.

Jan 1, 1968

[ ]

Jan 1, 1981

By E. Nickel

"Bi- and multilateral banks as well as export credit agencies in the OECD countries, but also numerous commercial banks, last year committed themselves to compliance with the World Bank’s standards. These environmental and social guidelines, also known as the Safeguard Policies, are the strictest international standards in the area of financing of major investment projects. The Safeguard Policies are procedural and quality guidelines by means of which socially and environmentally relevant impacts can be taken into account in the planning and implementation phase of a project. Objectives of the Bank Safeguard Policies are to ensure that environmental and social issues are evaluated in decision-making, to reduce and manage risk of projects and programs, and to provide a mechanism for consultation and disclosure of information. They are often referred to as the "10+1 Safeguard Policies," since ten of the guidelines address environmentally and socially relevant issues, while one guideline is exclusively concerned with public participation ("Public Disclosure"). In the presentation, the transparency of risk management measures and emergency response plans in pipeline projects will be discussed as an indicator of sustainability. The discussion is to be carried out on the basis of the results of an evaluation of several major pipeline projects, which have been financed at least in part by multilateral banks over the past few years. The controversies surrounding some of these projects due environmentally and socially relevant impairments connected with the investments have also been addressed by the Extractive Industry Report of the World Bank. Pipeline construction was the investment type chosen for the examination to be presented here, since pipelines frequently start in remote, unspoiled regions, and their routes often cross various natural zones and areas with various social structures. The question of safety during construction and operation of the line is always central to these projects; not only for the responsible authorities but also for other societal groups involved, such as environmental associations."

Jan 1, 2005

Rheological Behaviour of Clay-Rich Gangue Mineral Dispersions During Hydrometallurgical Treatment Alumino-silicate minerals invariable may present an intractable challenge in hydrometallurgical operations employed in low grade nickel, copper and gold ore leaching or high level nuclear waste (HLNW) processing. The interactions and reactivity of alumino-silicate clay gangue minerals such as muscovite/sericite, chlorite, kaolinite and smectite under acidic (eg pH <3) or alkaline (pH >13) conditions can have a striking impact on the particle interactions. These may manifest in undesirable pulp rheology, poor extraction rates and challenges in the subsequent "handleability" and solid-liquid separation processes (eg dewatering). In the present work, a review of investigations involving the interfacial chemistry, interactions and rheological behaviour of aqueous dispersions of mica-group, layered alumino-silicate clay (muscovite / sericite) and chalcocite minerals as a function of pH in the range 2 - 9 and time at 25¦C, is presented. Particle zeta potential, reflecting interfacial chemistry, indicated a strong pH-history and particle volume fraction dependency. Pristine particles' zeta potentials measured from high to low pH indicated mineral-specific isoelectric point (iep) at pH range 2 - 5. Subsequent measurements from low to high pH showed pH-history dependency with iep shift to higher pH values, the extent of which also depended upon particle volume fraction and aging time. Pulp pH-mediated particle interactions revealed by shear yield stress analysis displayed a bifurcation behaviour and good compliance with DLVO theory. The maximum pulp yield values occurred at the iep whilst weak rheology was observed where the magnitude of the particle zeta potential was greatest. The pivotal role played by both pulp chemistry and suspension conditions in regulating the particle interactions and concomitant rheological behaviour is highlighted. The implications of the findings with regards to clay-base pulps' handleability and its control during aqueous processing are discussed.  

Sep 13, 2010

By J. P. Sancho, L. F. Verdeja, J. I. Verdeja

"This paper analyzes the present state of the different processes competing to keep their market shares within the future iron and steel business sector.The continuous transformations in the steel making process are also studied here. These transformations have happened especially during the two last decades obviously favouring steel price, properties, quality and environmental compatibility in the new millennium. IntroductionIn the early 1980s, world steel production reached a historic figure; specifically in 1982, the amount was 645 Mt (Verdeja et al., 1993). This might have been one of the reasons why the United States, Japan and the European Community drew up a declaration of principles after which the leading industries and sectors in the following century’s development would be: advanced materials, also known by the very diffuse term of new materials; information technologies; and biotechnology (Eager, 1998).On the threshold of the 21st century, it can be inferred that information technologies (computers and telecommunications) have progressed spectacularly. Nevertheless, there have been downsides too; technology develops so quickly that after a few months the products are obsolete. Environmental problems may also appear in a few years due to storing so many useless devices. At the same time, the achievements of biotechnology did not meet the optimistic forecasts made in the early 1980s.On the other hand, it is also curious that some solutions for the environmental problems generated by star technologies of the new millennium, such as computers and biotechnology, are closely linked to the iron and steel industry. For example, blast furnaces in Germany and Japan are prepared for burning residua by introducing polymer materials from computers and other electronic prepared devices through their tuyeres, while cement tube furnaces can destroy any organic residua from different origins."

Jan 1, 2002

By Heitor Cristo Clem de Oliveira

O objetivo deste trabalho é estudar a reação de dessulfuração, envolvidas no processo de pré-tratamento de ferro-gusa. A princípio, as misturas utilizadas foram caracterizadas e estudadas através do software de termodinâmica computacional (FactSage 7.1). Em seguida, os resultados obtidos através do estudo termodinâmico computacional foram comparados com aqueles obtidos mediante os testes experimentais a 1400°C. As misturas dessulfurantes tiveram como base a CaO com três tipos de fundentes, fluorita, sodalita e barrilha, além da utilização de alumínio como elemento desoxidante. Os testes experimentais permitiram identificar que a adição de 0,1% em massa de alumínio no gusa, eleva a taxa de remoção de enxofre principalmente no instantes iniciais do processo. Com a utilização da termodinâmica computacional pode-se mostrar que a reação de dessulfuração no ferro-gusa é exotérmica para os teores de silício encontrados no processo. Além disso, a termodinâmica computacional também contribui, em alguns casos, para a análise de compostos sólidos que podem se formar na escória e limitar as reações de dessulfuração.

Oct 30, 2017

By João Alberto Fioresi Altoé

Nas indústrias petroquímicas, nucleares e farmacêuticas o avanço tecnológico tem como objetivo a segurança e confiabilidade dos equipamentos com relação à resistência mecânica e à corrosão. Atualmente, o uso dos aços inoxidáveis superausteniticos é uma solução interessante, para uma maior vida útil dos componentes industriais submetidos a ambientes agressivos, como em meios salinos. Esse trabalho tem como objetivo investigar o aparecimento de pites em um aço comercial superaustenitico de composição química aproximada 25Cr28Ni4Mo em solução salina de cloreto de sódio. O aço foi fundido e tratado termicamente por solubilização a 1050ºC por 1h com o objetivo de eliminar os precipitados. As análises microestruturais antes e após os ensaios de corrosão foram feitas por microscopia óptica e eletrônica de varredura. Observou-se com os ensaios eletroquímicos de Polarização linear e impedância, que o aço inoxidável superaustenítico apresenta excelente resistência à corrosão em meio salino, caracterizado também pelas imagens que não revelaram a formação de pites, mesmo quando submetidos a elevados potenciais.

Aug 16, 2017

By B. Caro Vargas

The Toulon South Tunnel in France is the second part of a project started 20 years ago. After the problems and delays suffered during the construction of the North Tunnel, due to a complex geologic context of highly fractured and soft rocks under a highly urbanized environment, a very dense automatic monitoring system was implemented to control the settlements of surface (more than 1000 points), the structures adjacent to the tunnel alignment and the underground galleries being constructed. The latest automatic instrumentation systems were installed, using for example AMTS capabilities in terms of ?automatic prismless settlement monitoring?. All the data (geotechnical, structural and geological) was gathered in a global automatic data acquisition system and continuously available on a web based interface. Three different threshold levels (notification, anomaly, alert) were set up, each one with a differential and an absolute value for settlements. Depending on the actual geological site conditions and the actual monitored settlements, different supporting systems and excavation techniques were used. Furthermore, the monitoring data was also used to predict and anticipate the future settlement, by comparing it continuously with the theoretical Peck settlement curves. This method allowed a better risk management by limiting the settlement on existing structures and helped to secure the Works progress schedule, for a project that lasts from July 2007 to March 2011. The implementation of this observational method application is presented in this paper.

Jan 1, 2012

By Y. K. Yen, J. D. Miller, C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA)system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall injury experience for coal mines, both anthracite and bituminous, coke plants, petroleum and natural gas, peat, and asphalt and related bitumens (native); metal mines, their metallurgical plants, including ore-dressing plants and primary nonferrous reduction plants and refineries; nonmetal mines; nonmetal mills; sand and gravel operations; slag (iron blast-furnace) plaints; and stone quarries and their related pants. Volume I of the yearbook contains a chapter showing injury experience and employment data treated separately by metal mines, nonmetal mines, quarries and their related plants, metallurgical plants (ore-dressing plants and primary nonferrous reduction plants and refineries are shown separately), nonmetal mills, sand and gravel plants, and iron blast-furnace slag plants. Volume II contains injury and employment experience in the fuel industries (coal, coke, petroleum and natural gas, asphalt and related bitumens (native), and peat. Injury and employment data are submitted voluntarily for the mineral operations through an industry canvass made by the Bureau of Mines, except for the coal industry, whose reports are mandatory. Information published in this chapter is the result of this canvass. Figures presented in this chapter for 1961 are preliminary except for anthracite, peat, coke, petroleum and natural gas, asphalt and related bitumens, and slag. These preliminary data, with the exception of bituminous coal, are a summation of reports received by May 31, 1962, from the operators showing their injury and employment experience. Estimations of injury and employment experience are not included in these preliminary data.

Jan 1, 1962

Ledcap Pty Ltd has developed two software tools for assisting in the determination of life-of-mine (LOM) trucking requirements. The first tool generates haul paths and the second calculates truck travel time over these paths. The two step approach allows the paths to be viewed and if required edited, to better represent the actual site haul routes.The first tool automatically creates haul paths between the mine bench and the dump. To do this the user supplies a master haul route and a scheduled block model. The master haul path and the block model are interacted to create multiple haul routes, one for each pit/dump bench pair in each scheduling period. Each path carries with it a record of the scheduling period it represents and the dry tonnage hauled over the path in that period.The second tool calculates truck travel time over the path. Data from the manufacturer's rimpull and retarder curves are used to calculate accelerations and speed over each segment of the haul path. As the paths are derived from digitised representations of mine haul routes the path f les often have over a hundred segments. This detailed representation of the haul route allows the software to automatically adjust speed for different radius corners and accurately simulates the changing accelerations over the gradient changes that occur in real life mine ramps. Rolling resistance can be specified at a global level, at a segment level and at a period level. This allows rolling resistance to be changed seasonally as well as spatially.Life-of-mine trucking studies attempt to calculate an accurate answer from extremely variable inputs. This paper will detail the features of the two software tools and how the tools provided in the software can assist the mine planner to have greater confidence in their life-of-mine trucking requirements and the subsequent production capacity inputs to their scheduling calculations.

Dec 6, 2010