Search Documents

By R. C. Diehl

Coal, fly ash, and flue gas samples were analyzed for mercury (Hg) by double gold amalgamation-flameless atomic absorption spectrophotometry. The purpose of the study was to elucidate the fate of the trace mercury in the coal when the coal is burned. Samples were collected from a bench-scale 100-g/hr combustor, a 500-lb/hr combustor, and three coal-burning powerplants. In all cases mercury was found in the fly ash. The amounts ranged from about 9 to about 70 percent of the mercury in the coal that was burned.

Jan 1, 1972

By J. D. Lane

The U.S. Bureau of Mines is conducting research on guidance systems for computerized haulage in underground mines. This report describes the process of component selection, installation and testing, perception algorithm development, and steering control algorithm development, to produce a real-time steering control system for an articulated haul truck for underground mining. Ultrasonic transducers were mounted on the truck to provide perception data by measuring the distance to the ribs. Linear potentiometers mounted inside the steering cylinders measured the steering angles. Algorithms, implemented on an inexpensive, robust onboard computer system, analyzed the data and controlled the steering via an electro-hydraulic proportional valve. The steering algorithm presented follows a zone defined by the relative position between the truck and a rib. Experimental verification of the ability to follow the zone in a test corridor on the Colorado School of Mines campus is presented. The automatic steering system successfully negotiated straight sections, curves, and the transition zones between straight and curves with the truck in first and second gears. The resulting real-time automatic-steering system can be applied to many underground articulated machines.

Jan 1, 1994

By A. B. Hooker, L. C. IlsLey

"Observation of the use of trailing cables in ""mines shows that the chief limiting factor in the life of the cables and their safe use is the smashing or crushing of the cables in service, together with the effects of consequent splicing.Trailing cables are crushed when run over by cars, mining machines; and locomotives or when hit by falls of roof. Crushing damages the insulation and may cause failure at once or in later use. Failure may be either by short circuit between the conductors or by grounding to the track. The failure of a live cable causes electric arcs capable of igniting explosive mixtures of methane and air. Every cable failure in a gassy or dusty mine is, therefore, a real or potential hazard.Some mine operators do not allow the splicing of trailing cables for use in gassy mines, bet require that a damaged cable be immediately replaced and if repaired that it be used only in nongassy mines. Other operators allow the making of temporary splices to permit completion of the shift but require that such splices be remade and vulcanized before the cable is used again.Still other operators allow the continued use of temporary splices, which in general means that a cable is used until the splices give trouble in reeling, or overheat, or pull apart. Then the spliced sections are either cut out or the whole cable is replaced.Splices often determine the useful life of a cable. A splice poorly made may pull apart ueder mechanical strain and cause arcing that burn* the surrounding cable or ignites as or coal-dust. If it has lower conductivity a splice is the first part of the cable to heat; it may become so hot under load that it will burn apart and damage other parts of the cable, or, if it be a soldered splice, the solder may melt and allow parting of the cable. A poorly made splice often has insufficient insulation which may alloy short-circuiting between conductors or permit external contacts capable of giving an electric shock to one handling the cable. The splice is sometimes bulky from too much insulation and takes up too much room on the reel, causing uneven reeling; also by catching on the spooling device the oversized splice may receive expressive pulls and wear. Splicing is therefore a very important factor in the use of trailing cables."

Mar 1, 1932

IN this paper an attempt is made to describe the sluicing operations on the tin fields of north-eastern Tasmania. No claim is made to completeness, for much of the ground has already been covered, and nothing is to be gained by needless repetition. On this account some portions of the subject have obviously received but attention in order that others may be rather more fully dealt with; for instance, referring to the accuracy of various methods of valuing alluvial deposits, particulars of efficiencies, and water duties on both overburden and drift; also, the system of recording water distribution, &c. The plans of the tin-streaming shed, sluice and feed race, and overburden tail-race represent types of the most modern design.GEOLOGY. The principal alluvial dcposits being worked at the present time are situated either in the ancient or modern bed of the Ringarooma River or its tributaries. This river flowed in a north-easterly direction, receiving numerous tributaries on either bank...

Jan 1, 1910

Essential features of the role of the fill material in mechanized cut and fill mining are discussed, with particular emphasis on its dewatering and strength development after emplacement. The fill material is regarded as a chemically-reactive porous medium, the most important property of which is permeability. Methods are described for measurement of permeability and other fill properties and results of such measurements applied to develop an orderly approach to the operation.

Jan 1, 1966

By Harry H. Power

INDUSTRY has the right to expect the petroleum engineering schools to supply more than the minimum technical qualifications necessary to obtain or discharge the responsibilities of a particular job. The basic training, social and economic orientation, should go far beyond these minimum requirements. Petroleum engineering students should also be well grounded in the history of the oil business so that they may understand the industry's progress since the advent of the Drake well. Furthermore, according to P. H. Bohart, the schools "have a definite duty to help the students form a workable philosophy of life, which includes an appreciation of the service of science to mankind, and a belief in the obligation of the individual who enters a profession to exalt himself by continuing his studies and growth so that he may never cease making contributions to the advancement of science and industry."

Jan 1, 1948

A simple process for making filter aids from coal by controlled carbonization at 800-1200·C is described.Several possible variations in reactor design have been used experimentally, involving fluidized beds of carbon or inert material, reaction of the particles while entrained in air, and a combination of entrainment and fluidization.Product yields depend upon the composition of the parent coal but are always less than the sum of the ash and fixed carbon values determined by the proximate analysis. The product yield also depends on the air-to-coal ratio, which affects the amount of coal substance burned and the temperature attained. Particle residence time and reactor temperature affect the degree of devolatilization of the product and hence its wettability. The filtration behaviour of carbonaceous filter aids is greatly influenced by the size distribution, shape and physical properties of the particles-parameters which are largely determined by fue type and particle sizing of the coal used.Carbonaceous filter aids are distinctly different from other types commonly used and extensive industrial applications are anticipated in a wide range of industries ranging from food to mineral processing.

Jan 1, 1970

By V. Pawlowsky-Glahn, E. Pardo-Igúzquiza, J. J. Egozcue, R. A. Olea

Compositional data constitutes a special class of quantitative measurements involving parts of a whole. The sample space has an algebraic-geometric structure different from that of real-valued data. A subcomposition is a subset of all possible parts. When compositional data values include geographical locations, they are also regionalized variables. In the Earth sciences, geochemical analyses are a common form of regionalized compositional data. Ordinarily, there are measurements only at data locations. Geostatistics has proven to be the standard for spatial estimation of regionalized variables but, in general, the compositional character of the geochemical data has been ignored. This paper presents in detail an application of cokriging for the modelling of compositional data using a method that is consistent with the compositional character of the data. The uncertainty is evaluated by a Monte Carlo procedure. The method is illustrated for the contents of arsenic and iron in groundwaters in Bangladesh, which have the peculiarity of being measured in milligrams per litre, units for which the sum of all parts does not add to a constant. Practical results include maps of estimates of the geochemical elements in the original concentration units, as well as measures of uncertainty, such as the probability that the concentration may exceed a given threshold. Results indicate that probabilities of exceedance in previous studies of the same data are too low.

Jan 1, 2015

By John R. Koehler

Available barrier pillar design methods do not adequately account for overburden caving characteristics, the timing and magnitude of associated load transfers, the occurrence of unusual geologic features, or the effects of multiple-panel/multiple-seam mining. To address this problem, the Bureau of Mines, in cooperation with Cyprus Plateau Mining Corporation, conducted a barrier pillar study in a multiple-seam mine setting. Insufficient barrier width resulted in excessive load transfer to an adjacent/underlying section. Consequent entry and pillar deterioration resulted in the section being prematurely abandoned. This paper proposes an approach based on in situ measurements, which includes mine-specific loading conditions in the barrier design process.

Jan 1, 1989

A pilot steel ladle injection facility designed to assist in the production of high quality steels suitable for use in pipelines has been built and commissioned at the Basic Oxygen Steelmaking (BOS) plant at Port Kembla Works.The plant design and the injection procedure are described.The performance of the unit and some metallurgical results are discussed in terms of the addition to the steel ladle of various quantities of calcium silicide and a lime based material. The effects of these additions on sulphur content and inclusion morphology and hence on steel ductility are also presented. The influence of ladle lining on desulphurisation is illustrated.On the basis of the experience gathered in the pilot plant a permanent and more sophisticated injection facility has been designed.

Jan 1, 1983

By A. L. Edwards

A two-year study focused on current noise exposure levels in the South African mining industry, aimed at helping the Mine Health and Safety Council of South Africa meet its milestones for eliminating noise-induced hearing loss (NIHL). Methods A multi-task methodology was adapted from international baseline studies to determine the exposure to noise in both large-scale and small- to medium-scale mines. Results On average, 66.7 per cent of the employees sampled in year 1 and 78.4 per cent in year 2 were exposed to noise levels of above the 85 dB A legislated occupational exposure level. Conclusions Information obtained through the study could be developed into a national personal noise exposure database, including audiometric results, equipment noise emission levels and initiatives for noise engineering control by mines and equipment manufacturers to facilitate targets of eliminating NIHL. Keywords Noise exposure levels, mining industry, noise-induced hearing loss

Jan 1, 2011

By Boyd Wise

A jet pump injector was developed and successfully tested, thereby demonstrating the feasibility of a jet injector for introducing coarse coal into an operating slurry face haulage system: In Phase I a variety of injection concepts were evaluated, and the jet pump was identified as best, due to its simplicity, compactness and performance potential. In Phase IIA subscale jet pump injector tests were conducted, and a computer model of a jet pump injector was developed whose performance predictions correlated well with subscale test results. In Phase IIB various system configurations were defined for integrating a jet pump injector into a fully operational underground coarse slurry face haulage system, further highlighting the feasibility and practicality of such a system. In Phase III a full-scale mobile haulage vehicle embodying a jet pump injector and coal sizing equipment was detail designed into a practical vehicle with attractive performance characteristics. More importantly, fully operational full scale jet pump injector -and feeder/breaker subassemblies were tested and proven successful in their ability to down-size coal to 3" in all 3 dimensions and to consistantly provide slurry of 4217 weight concentration at 6.4 TPM throughput under a wide range of operating conditions including zero to maximum feed rate within 5 seconds.

Jan 1, 1985

By R Lewis

Drill hole magnetometric resistivity (DHMMR) is a relatively recent addition to the explorationistsÆ suite of techniques for finding further resources in the vicinity of a drill hole. The method relies on gathering of an applied current into zones which are less resistive than the country rocks and it was first applied to exploration programs looking for weakly conductive sulphides, such as, for example, carbonate-hosted zinc deposits. More recently, it has been applied to a wider range of deposit styles, including highly conductive nickel sulphides. It has been found that the technique is capable of not only detecting mineralisation not seen by conventional electromagnetic (EM) techniques, but it can detect at a greater distance. Also, whilst EM is superior at defining tabular-shaped conductors, DHMMR may be more effective at finding cigar shaped sulphides. This paper presents a number of examples illustrating these findings.

Jan 1, 2000

By Daniel Augusto Ferro

Devido crescente necessidade de elevação dos níveis de conformação em peças estampadas, existe uma demanda cada vez maior em ligas e processos diversificados que atendam as variadas exigências do setor de produtos estampados e posteriormente tratados termicamente para aumento de dureza. Desse modo desenvolveu-se a liga C80M (modificada), que é uma variante da liga C80U especificada na norma DIN EN ISO 4957 porém com adição de Cromo, entretanto a liga C80M ainda é pouco estudada e pouca informação técnica se tem a seu respeito. Com a finalidade de melhor conhecimento técnico dessa liga, foram conduzidos estudos de caracterização em amostras laminadas a quente e após processo de esferoidização posteriormente sendo revestidas com fosfato de zinco. Foram realizados estudos de composição química, microestrutura e propriedades mecânicas, além de levantamento da curva CLC através do método Nakazima em amostras com e sem revestimento de fosfato. Através dos resultados parciais encontrados, foi possível definir o lado da curva CLC relacionado ao estiramento da chapa bem como comparar o deslocamento e a força do punção no teste Nakazima conformando-se amostras esferoidizadas sem e com revestimento de fosfato.

Jul 30, 2018

By AIME AIME

WHEN I was getting data for my books on ore dressing, I traveled across the continent, visiting a great many mills, always accompanied by my vanning shovel, and I got to be a joke among the millmen. They would say "Here comes the Professor with his vanning shovel." With the aid of this vanning shovel, I examined the tailings of all the mills I visited and I found it to be universally true that they contained some extremely fine, free mineral. I looked everywhere to see if I could find a machine or a process that would save this fine mineral. But nowhere did I find anything that made any bid for success until I visited the Kennedy mill, with its Gates canvas plant, on the Mother Lode of California. There I found that the tailings of the Frue vanners were put into a one-spigot classifier of good design which yielded a spigot product entirely free from this fine, free mineral which only assayed 40c. to the ton in gold. The overflow was extremely fine and as¬sayed $3 to the ton. This overflow was fed to ten canvas tables each 10 ft. square, with the grain of the canvas running across the table to make for the roughest surface. The canvas used was No. 6 cotton duck sail cloth.

Jan 1, 1934

By E. Petrakis, K. Komnitsas

The main objective of batch grinding modeling is the estimation of the product particle size distribution over time or specific energy input to the mill. So far, the developed analytical methods require often complicated calculations which are timeconsuming. Thus, more simple approaches that allow the reliable prediction of the complete product size distribution need to be developed. In the present paper, an approach, based on the population balance model (PBM), that reliably predicts the product size distribution is proposed. In order to enable this, the simplified form of the fundamental batch grinding equation was transformed into the well-known Rosin–Rammler (R-R) distribution, thus allowing the determination of the breakage rate for each grinding period. A time-dependent breakage rate framework was developed where the traditional linear theory of the PBM is considered a partial case. This approach allows the deviations from the linear theory to be categorized and the degree of the acceleration-deceleration of the breakage rate to be predicted. Modeling results were validated by laboratory grinding studies using two homogeneous materials, quartz and marble, and one heterogeneous, a limonitic laterite. The experimental data revealed that grinding exhibits non-first-order behavior and the degree of deviation from the linear theory depends on the tested material. The reliability of the proposed model was validated with the use of the distribution modulus n, the a value of the breakage rate parameter, and the optimum n values that minimize the sum of the differences between the experimental and estimated particle size distributions.

Feb 8, 2021

By Wade A. Narin, James K. Mitchell

Hydroblasting is considered a distinct soil improvement technique from explosive compaction, though the blast designs for the two techniques are similar. Hydroblasting is a three step process developed for densifying unsaturated, collapsible soils, especially loess. The required steps are: prewetting the soil to an adequate saturation, placing and detonating the explosive charges, and consolidating the soil (squeezing the water out of the pore spaces between the soil particles under gravity) to a denser state.

Jan 1, 1995

THE Yallourn chimney has aroused interest, as it is, for the time being, the tallest structural erection in Australia. Its height was not decided on, however, with the object of breaking records, but is purely incidental to the purpose which it serves. Theboiler plant at the briquetting works (first instalment) consists of five Babcock and Wilcox land-type water-tube boilers, each of 4510 sq ft. heating su:r£ace and 225 sq. ft. grate area in the form of step grates. Four boilers will normally produce 73,000 lb. of steam per hour at a gauge pressure of 265 lb. and a temperature of 6500 F., the fifth boiler being a reserve. Each boiler will consume about 100 tons of Yallourn coal per 24 hours. Provision is made for future installation of economizers, should it be found desirable. Designing for this condition, and allowing for a waste gas temperature of 3500 F. and an air temperature exceeding 1000 it was found necessary to have a draft of about 1.3 in. (water gauge) at the base of the chimney, and to deal with about 2000 cub. ft. of gases per second. Estimates were made of the cost of providing the necessary draught by means of fans and by means of a tall chill).ney. The annual charges of the two methods differed only slightly, and the tall chimney wasselected as being the more general practice in briquetting factories.Estimates were prepared for brick and concrete chiIlllleys. Yallourn bricks at that time were hand-made, and, while very suitable for domestic work, were not capable of withstanding high compressive stresses. The chimney design to suit these bricks thus required to be on very ample lines, resulting in high cost. Machine-made bricks from Melbourne would cost about £5 10s. per thousand on the site, with extra for radials, so that high cost again resulted. On the score...

Jan 1, 1924

By D. M. Wagner, G. Biggs, M. Osmundson, C. J. Twaroski

Potential air emission impacts to federal Class I areas from distant sources are receiving increasing scrutiny by federal land managers (FLMs). This paper provides summary results of the impact analyses conducted for FLMs and PSD permitting of a proposed expansion for a taconite processing facility. Results from air quality increment, acid deposition, mercury deposition, and visibility analyses for Class I areas located 50 to 162 km from the facility showed the project would meet the respective regulatory and guideline values for the specific analyses. During the course of the air quality analyses, potential new requirements from the FLMs’ Air Quality Related Values Workgroup (FLAG) efforts and USEPA’s Regional Haze Program were brought into the PSD discussions. The implications for these future guidelines and regulations as they may affect future expansions at other mineral processing facilities are also discussed.

Jan 1, 2001

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996