Search Documents

The selection of the best comminution circuit for the preparation of concentration feed is a compromise based on economics, energy efficiency, labour costs, steel consumption, availability and other factors specific to each case. It is postulated that the selection must be a choice of one of the eight basic comminution circuits which can be divided into two basic groups, (1) autogenous or semi-autogenous primary mills with or without a secondary grinding stage and (2) fine crushing usually in cone crushers followed by a rod mill-ball mill circuit or a single stage ball mill circuit. The accuracy of selection may be improved by pilot plant and laboratory tests which are described in this paper. For (1) above, testing includes media competency tests with standard impact crushing, grindability and abrasion tests followed by pilot plant tests. For (2) above, bench scale crushability, grindability and abrasion testing is available. It is suggested that, through these tests, it should be possible to eliminate all but one in each group of basic comminution circuits. Then engineering and economic studies should lead to the best comminution circuit for the specific requirement.

Jan 1, 1984

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

By H. M. Chance

STRETCHING from New York southwestwardly to Georgia is a great range of hills and mountains consisting of pre-Palaeozic schists, slates, and gneissic and granitoid rocks, known locally by many different names; in Pennsylvaniaa as the South mountains, the Berkshire or Durham and Reading hills, and in Virginia and farther south as the Blue ridge. To the northwest of this range lies the " Great Valley," underlain by Lower Silurian limestones, and known as the Lehigh valley, Cumberland valley, Shenandoah valley, valley of Eastern Tennessee and Georgia and by other local names, but all these are parts of one valley, geologically and geographically continuous from New Jersey to Georgia. Lying upon and along the northern flank of this range of mountains, and dipping northwestwardly under the limestone of the valley, is the Potsdam formation (Primal or No. 1 of the Pennsylvania Geological Survey), which consists of sandstone or conglomerate overlain by slates. The latter are sometimes arenaceous and occasionally are replaced in part by sandstone. This formation varies from a few feet to several hundred feet in thickness. At the outcrop the slates are completely decomposed, oxidized or disintegrated, forming a belt of clay several hundred feet wide occupying the interval between the outcroppings of the sandstone and limestone. This clay-belt includes a more or less continuous series of iron-ore (brown hematite) deposits, which have been, and still are, extensively worked. The belt is more or less continuously mineralized with iron throughout its length, and hundreds of large deposits of ore have been developed and worked, producing many millions of tons of ore.

Sep 1, 1908

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By Earl T. Hayes

[This work represent a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of miner physics to processes metallurgy.]

Jan 1, 1941

By Earl T. Hayes

[This work represents a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of mineral physics to process metallurgy.]

Jan 1, 1941

Rockbursts continue to be a scourge in the mining industry, being responsible for accidents and damage to mining excavations. Although the problem has been present for more than a century, and although much research has been carried out, a solution is still elusive. Determination of, firstly, the demand on the support system imposed in the rockburst and, secondly, the capacity of the support system, cannot be carried out with any confidence, and therefore rockburst support cannot be designed using a conventional design approach. In contrast with the conventional approach, observations of rockburst damage in a mine have revealed a possible alternative approach to rockburst support ? sacrificial support. It was observed, in rockburst events, that a support system consisting of concrete panels restrained by grouted cables was destroyed, and the concrete panels were ejected. However, the rock behind the panels remained apparently undamaged and in place. This behaviour reignited the concept of sacrificial support, conceived more than 20 years ago, and which is described in this paper. The remedial solution implemented on the mine, involving cables wrapped over the panels and retained by grouting into boreholes, has been subjected to rockburst loading and has confirmed the validity of the sacrificial support concept. The concept of sacrificial support may be controversial, but is deliberately presented here with the aim of generating discussions and contributions, and with the ultimate aim of improving safety and reducing rockburst damage in mines. Keywords rockburst, seismicity, seismic waves, rock support, support design.

Jul 1, 2013

By F. L. Wideman

This paper is one of a series on mining methods being published by the Bureau of Mines. It describes briefly mining practices at the Sunrise iron mine of the Colorado Fuel & Iron Corp., Platte County, Wyo. The Sunrise mine is in the Hartville iron district in east-central Wyoming (fig. 1). The district covers part of the Hartville Mountains, a region of moderate relief in which erosional features have been formed by the dissection of a low plateau. Altitudes vary from 4,300 feet along the North Platte River to 6,000 feet in the uplift. The climate is semiarid, with hot summers and winter temperatures below zero for short periods. Grasses, cacti, yucca, and low desert shrubs grow at lower elevations. Cottonwood and boxelder trees and willows grow along permanent streams; juniper and coniferous trees are confined to the higher elevations.

Jan 1, 1956

By Mills R, Shannon W. T, Finch J

As an extension to investigations into methods of upgrading the Iitania content of ilmenite concentrate from beach sands using 100 g/day, a small pilot plant treating 23 kg/ day of ilmenite was used.In the pilot plant the iron oxide in the ilmenite was reduced to iron at 1200°C using carbon (coal/char) without melting the material, using a tunnel kiln heating cycle, the charges contained in saggars, The iron was then separated from the titania fraction by ball milling, wet magnetic separation, and screening. The resulting magnetic product was high in iron (about 80 per cent Fe) and the non-magnetic product high intitania (about 70 per cent TiO2).From this trial sufficient data were obtained to enable the preparation of a flow sheet for a plant producing 62,300 tonnes/year total products, and an estimate of costs to be made. This has shown that for an estimatedcapital expenditure of nearly $6,000,000 and annual production costs of about $4,000,000, the cost per tonne of high titania product (76 per cent TiO2) would be nearly $70.

Jan 1, 1977

By R. E. Hummel, J. W. Koger

IT is generally accepted that the martensitic start temperature (Ms) can be determined by resistivity measurements and is that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line.1-4 Both Titchener and ever' and pops5 have used resistivity measurements to follow the martensitic transformation in b1 Cu-Zn and ternary Cu-Zn-based b-phase alloys, respectively. Actually because of the nature of their measurements the temperature of minimum resistivity (M) was used by these authors to determine "Ms" . Also, due to experimental difficulties in detecting M, with resistivity measurements, Pops and Massalski 8 determined M, by optical microscopy. The present communication is concerned with high-precision, low-temperature resistivity measurements which reveal a definite M, temperature which differs from the temperature of minimum resistivity (M). It is also shown that M is merely the result of the geometry of the percent-transformation curve and the temperature coefficient of resistivity of the alloy. In other words, it will be demonstrated that M has no apparent significance (except that it denotes a temperature at which some percent of martensite can be detected in a given alloy). Alloy specimens were made by melting 99.999 pct Cu and 99.9999 pct Zn in sealed and evacuated quartz tubes and homogenizing them at 601PC for 300 hr. After the alloy was cold-rolled into foils suitable for resistivity measurements, it was quenched in ice water from 871PC. The chemical analysis showed a zinc content of 38.8 wt pct. The cooling rate during the martensite transformation was 1°C per min and was controlled with a thermistor. Electrical resistivity measurements were made using a K-3 type potentiometer; the reproducibility of the resistivity values was better than 0.03 pct. Temperatures were measured with a thermocouple to an accuracy of better than 0.2° C. Fig. 1 shows the resistivity vs temperature curves of the martensitic transformation in B1 Cu-Zn for both cooling and heating. The starting point of the martensitic transformation (M,) was taken as that

Jan 1, 1968

By Xintan Chang

MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under the influence of natural ventilation, fans, fires, or any combination of these. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influences (varying outside temperatures), and internal influences (fires). Extensive output enables detailed, quantitative analysis of the effects that the alteration will cause to the ventilation system. The program was developed at Michigan Technological University (MTU), Houghton, MI, with support from the Bureau of Mines. A personal computer (PC) version of the program was completed under contract for the Bureau by MTU. The purpose of this report is to document the installation and use of the PC version of the program MFIRE.

Jan 1, 1990

Significance of the body of iron oxide, which in part overlies as its hanging-wall the rich chalcocite ore-body at Mount Oxide, Queensland, has been variously interpreted by engineers and geologists who have inspected the deposit.Among the interpretations offered is the one that the body represents the residual of an original medium to low grade...

Jan 1, 1939

By K. D. Hester

"1.0 INTRODUCTIONThe uranium industry started in Canada with the reopening of the gravity concentrator at Eldorado's Port Radium mine in the North West Territories in 1942. In 1948, uranium exploration and processing was opened to the private sector, and the Federal government offered special pricing incentives to the industry. Eldorado explored the Lake Athabaska deposits in northern Saskatchewan, and in 1953 opened the Beaverlodge mine. Other mines in the area soon followed. In 1953 also, the deposits in the Blind River - Elliot Lake area and in the Bancroft area of Ontario were discovered. Mines and mills were quickly developed in these areas.Canadian uranium production peaked at 15,900 short tons of U3O8 in 1959. In that year, uranium exports at $300,000,000 exceeded those of all other minerals in value. On October 1, 1959, Canadian uranium operations employed 13,900 people.Up to 1956, it was a seller's market. By 1958, world production of uranium was far ahead of requirements. Accordingly, in November of 1959, the USAEC announced it would not renew it's options for continued delivery of uranium from Canadian mines. This led to the ""stretchout"" of existing uranium contracts, and many mines were shut down (see Table 1) .In the early 1970's, a commercial uranium market seemed to be developing. In Ontario, at Elliot Lake and Bancroft, mines reopened. But competition was coming from the Athabaska basin of Saskatchewan. Currently it is these high grade, open pit deposits of northern Saskatchewan which are in the forefront of Canadian uranium developments. Canadian developments since 1942 reflect the political and market forces, as well as metallurgical progress and changes in environmental standards. This paper attempts to show these process changes in broad perspective."

Jan 1, 1987

By Christopher J. Vise

Although production operations at mines, representing the extraction and removal of the mined material, often appear to receive the greatest amount of attention, the emphasis given to auxiliary operations is continually increasing. This is due to the changing economic, social, and environmental climate in which modern mines must operate. Auxiliary operations can best be described as those activities that are not directly related to the extraction and removal of the mined material, but must receive proper attention if recovery is to take place in a safe, efficient, and socially responsible manner. In fact, certain mining auxiliary operations, such as strata control and ventilation, are considered to be of such importance that they warrant separate sections in this Handbook. Judging from a mine-personnel standpoint, it is not uncommon for a mine to hire the same number or more individuals responsible for auxiliary operations as the number assigned to production.

Jan 1, 2008

By Walter R. Storms

"INTRODUCTION The New Mexico potash exploration described herein was begun in February 1944 with the object of determining the amount of potash ore in the United States Potash Reserve in Eddy County by exploring the deposit from the surface with vertical drill holes. The work was completed in October of the same year after 16 holes had been drilled on the Reserve and in the immediate vicinity.The Potash Reserve is in secs. 26; 27, 34, and 35, T. 20 S., R. 29 E., Eddy County, N. Mex., about 14 miles northeast of Carlsbad, as shown on figures 1 and 1A, Drilling was done in secs. 26 and 35 of the Reserve, in section 14 to the north, end sections 2 and 56 to the east. All work was done on Governnent-owned, unleased land.The Reserve may be reached from Carlsbad by traveling to the north-east by automobile for about 14 miles on the paved U. S. highway 62. This highway passes through the southern part of the Reserve. Other parts may be reached by a State highway that passes along the eastern side of the area, then by poor dirt roads to various drilling sites. A branch of the Santa Fe Railroad also passes across the southern part of the Reserve enroute from Carlsbad to the plant and mine of the Potash Co. of America, a few miles northeast of the project and 22 miles from Carlsbad."

Aug 1, 1947

By Keith S. Olson

During 1982 and 1983, the Bureau of Mines concentrated its fugitive dust control research on haulage road dust suppression by newer chemi-cals relatively unknown in the mineral industry, innovative dust control designs for haulage trucks, chemical tailing basin stabilization, and combined chemical and vegetation tailing basin stabilization. Relatively unknown dust suppression chemicals and innovative aerodynamic modifications to haulage truck fender designs were tested on a Minnesota sand and gravel operation haulage road. Magnesium chloride salt at 95-pct control efficiency and a petroleum derivative at 70-pct control efficiency were effective in suppressing dust generated by haulage vehicles; however, none of the fender modifications were successful. Commonly used dust suppressant chemicals were tested on a Minnesota taconite tailing basin to reduce the dust lift-off during the spring and fall dry seasons. The most successful chemical was lignin sulfonate with a seasonal cost of less than $200 per acre to achieve 90-pct dust control. When chemical treatments for immediate dust control were com-bined with revegetation for permanent control, the most promising chemical treatment based on vegetation response was lime-neutralized lignin sulfonate.

Jan 1, 1987

By Arturo Ressi di Cervia

The utilization of diaphragm wall construction in Hong Kong began in 1974 with the construction of the New World Center, the first diaphragm wall job built in the British Colony. That landmark job of which I am presenting a few slides and a schematic description, embodied all of the difficulties and problems which are encountered in the difficult geology of Hong Kong. A small rocky island in the South China Sea, Hong Kong provides one of the finest natural harbors in the world. It is its splendid harbor, coupled with the enterprising attitude of the Hong Kong Chinese and the laissez-fair attitude of the British government which has resulted in the explosive growth of this speck of land soon to revert to the political control of mainland China.

Jan 1, 1993

By Padmavathi V, M. Najamuddin, M. R. Madhav

Granular piles are one of the leading ground improvement techniques, adopted for the betterment of bearing capacity and reduction in settlements of the foundations and also to accelerate consolidation of the surrounding soil. In the recent past, there has been extensive research on the settlement analysis and behavior of granular piles under varied soil conditions. The application of these theoretical solutions to practical problems requires a knowledge of representative values of the deformation parameters of the ground and the granular piles. However, very little information is available on these parameters. The paper presents a new method for the estimation of the modular ratio of granular piles and modulus of deformation of the surrounding in-situ soil from the compression load tests. The load - settlement response obtained from the compression test results are used in the back analysis for estimating the modulus of deformation of the ground. The presence of granular bed, under the rigid plate for load testing, has been given due consideration in quantifying the proportion of load transferred on to the stone column. Based on these considerations a new method is developed to estimate the modulus of deformation of the ground and the modular ratio of the granular pile.

Sep 1, 2022

By Bin Tang, Suping Yao

In the last decade, the copper industry in China has developed rapidly and attracted the world’s attention. The production capacity of refined copper has grown remarkably from 4.578 million tons in 2010 up to 9.029 million tons in 2018, accounting for about 40% of the global refined copper production. And now, China has become the biggest refined copper producer in the world. This paper summarizes the application of modern copper metallurgical technologies such as Outotec flash smelting/converting technology, Cyclone smelting technology, TSL (ISA/Ausmelt) smelting/converting technology, Jinfeng side blown smelting and Baiyin side blown smelting technology, Chifeng side blown smelting and continuous top blown converting technology, SKS bottom blowing technology, Dongying two-step smelting technology, copper electrorefining with high current density, etc. in China’s copper industry, analyzes and compares the characteristics of those technologies and presents the great efforts of China’s copper smelters in adapting to the increasingly strict emission standards and improving economic benefits of copper smelters. INTRODUCTION China has been the biggest refined copper producer in the world for many years. China produced million tons of refined copper in 2018, accounting for 40% of the copper smelting production in the world, and of which, roughly, 70% of the copper concentrate was imported, mainly from Chile, Peru and Australia. ICSG (International Copper Study Group, 2017) shows clearly the position of top 20 countries of copper production and copper mine production (Figures 1 and 2). Blast Furnaces, Reverb Furnaces and Electric Furnaces dominated China Copper Smelting for quite long time till 1980s. The first modern copper smelting technology (flash copper smelting) was introduced into China in 1980s, then followed by Noranda, Ausmelt and ISA. Since then, China copper smelting technology stepped into modern time. Since 2000, old processes (Blast Furnace, Reverb Furnaces and Electric Furnaces) were phased out and replaced by modern smelting technologies. China Copper Production has been increasing dramatically (Figure 3).

Jan 1, 2019