Search Documents

By Lowell L. Patten

The Federal Bureau of Mines participated with the National Aeronautics and Space Administration and Martin Marietta Aerospace in developing, building, and testing a portable X-ray fluorescence spectrometer for use as an analyzer in mineral-resource investigative work. The prototype battery-powered spectrometer, measuring I1 by 12 by 5 inches and weighing only about 15 pounds, was designed specifically for field use. The spectrometer has two gas-proportional counters and two radioactive sources, 109Cd and 55Fe. Preliminary field and laboratory tests on rock specimens and rock pulps have demonstrated the capability of the spectrometer to detect 33 elements, to date. Characteristics of the system present some limitations, however, and further improvements are recommended.

Jan 1, 1982

By John D. Foulkes

An investigation is made into whether commercially available equipment can be used to engineer effective emergency warning systems for underground coal mines. Discussions with members of the Bureau and the Mining Enforcement and Safety Administration established that the preferred system should operate over the existing Pager Phone twisted pair, and broadcast an audio alarm. Applicable equipments such as voice band tone signaling equipment, alarm sounding equipment, mine telephones and complete alarm systems from over thirty manufacturers are listed. Factors affecting the range over which an alarm could be detected in representative mine situations were studied. These included (a) the subjective masking effects of typical background noise found in mines, such as that due to continuous miners (b) the attenuation of sound in mines (using both a theoretical and experimental results) and (c) the attention-getting qualities of different sound for miners. Audio alarm systems meeting the requirements can be installed and representative systems are described.

Jan 1, 1977

By Erik C. Westman

Knowledge of the orientation and relative magnitude of in-situ stresses at the mine scale is important for safe and efficient production from an underground mine. With this knowledge, stope location and scheduling can be optimized. Passive seismic tomography was used for imaging horizontal stress distribution at the mine scale. Microseismic measurements from the Creighton mine were used as input for the tomography calculations. The double-difference tomography algorithm was used, which provides the most precise results. The results clearly show a low velocity zone in the previously mined areas bounded by two high-velocity lobes located adjacent to the mined openings at locations consistent with those expected due to the horizontal stresses at the mine. The overarching goal of the research is to provide a tool that can augment both numerical modeling results and underground geotechnical measurements to allow the mine operator to produce in the safest and most efficient manner possible.

Jun 1, 2012

By D. H. Desy

The Bureau of Mines studied the properties of copper that had been oxide dispersion-strengthened with 2 vol pct of either yttria or alumina. Compounds of copper and aluminum or yttrium, coprecipitated from aqueous solution, were converted to oxides; the copper was reduced, compacted, sintered, and extruded. For the resulting copper-dispersoid composites, room temperature tensile properties after annealing in hydrogen, elevated temperature tensile and stress-rupture properties, and electrical conductivity were determined. Compared with oxygen-free copper, copper-2 vol pct alumina or yttria had improved strength after annealing between 400° and 1,000° C, and improved elevated temperature strength, with little loss in electrical conductivity.

Jan 1, 1969

By By Staff

"Acid mine drainage can be controlled by water treatment, retardation of the pyrite oxidation reaction system, or enhanced prediction that allows preventive action to be taken. The Bureau of Mines is conducting research in each of these areas; the results of this research are summarized in the eight papers that comprise this volume. Field work to evaluate overburden analysis, alkaline injection, and bactericidal control of acid formation is described, along with two new inexpensive methods to treat acid mine water. These papers were prepared for an acid mine drainage technology transfer meeting held in Pittsburgh, PA, on April 3 and 4, 1985. INTRODUCTIONAcid drainage from coal mines is one of the most persistent industrial pollution problems in the United States. Over 5,000 miles of streams and rivers are adversely affected, primarily by underground mines that have been abandoned for decades. Meanwhile, at active mining operations and at sites where mining occurred after 1977, discharge water must be treated to meet fairly stringent regulatory limits--at a cost to the industry of over $1 million per day.The Bureau of Mines has a special responsibility to facilitate integration of mining and mineral processing with environmental safeguards. This responsibility is twofold: the development of techniques to reduce or eliminate environmental degradation, and the improvement of existing pollution control processes to make them more efficient and more cost effective. Research in acid mine drainage exemplifies the Bureau's concern for these environmental aspects of mining.This collection of papers summarizes much of the Bureau's recent research on acid mine drainage and will give the reader a sense of where the research is headed, in addition to providing details regarding new technology and recently acquired knowledge. The research papers address four basic objectives:"

Jan 1, 1985

By Fei Dai

Musculoskeletal disorders (MSDs) are a group of painful disorders that affect muscles, tendons, nerves, joints, cartilage, and ligaments. They are a serious problem among the workforce in the United States. In the construction industry, high physically demanding tasks expose construction workers to a number of well recognized MSDs risk factors such as repetitive motion, high force exertion, and awkward body posture. Finding ways to effectively identify and evaluate risks of MSDs can significantly alleviate this problem. To this end, this paper reviews state of practice and research in the assessment of risks of MSDs among construction workers, in which a number of biomechanical models have been developed to evaluate joint and tissue loading with the aid of state-of-the-art remote sensing technologies. Findings from the review reveal that despite the advances in tracking human motion and muscle activities, current remote sensing approaches still involve sophisticated instrumentation and expensive experiment setup. These factors greatly limited the applicability of such approaches in real construction settings. How can we detect and evaluate the construction worker?s MSDs risk in real work environments? In this paper, strategies by utilizing video surveillance systems are presented, to set the stage for addressing the above question and discussing future research in real-time, marker-less, and costeffective MSDs risk assessment.

Aug 1, 2013

By Eugene McAuliffe

THE last obtainable figures of the value of the coal mining investment are those contained in the U. S. Census Reports, from data gathered in 1919. The values shown therein and set forth below cover lands and equipment and do not include distribution and marketing facilities. The working capital necessary to meet pay rolls to purchase material and supplies and workmen's compensation insurance are likewise excluded.

Jan 1, 1926

By John C. Machisak

INJURY DATA and experience at, coal mines in the United States for 1953 and 1954 are presented in this publication with a minimum of interpretation and comment because of the numerous tables required to afford detailed comparisons between the 2 years. Corresponding tables for 1953 and 1954 follow in consecutive order under the following general sections: (A) General injury experience: Tables 1 to 11: Contain current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity and time-loss rates. (B) Selected injury data: Tables 12 to 85: Contain current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines.

Jan 1, 1958

By Carl L. Bieniewski

In a Bureau of Mines supply evaluation, the known uranium resources in the United States are estimated to have a total recoverable uranium oxide (U3O8) content of 3,132,400 tons at prices up to $69.32 per pound. Only those resources were evaluated for which sufficient quantity data are available and process technology exists for recovering uranium. A total of 160,800 tons of U3O8 is available at $8 per pound from ore deposits presently mined and an additional 244,700 tons available at prices up to $30 per pound from similar but usually lower grade deposits. A total of 2,726,900 tons of U3O8 is available from four other resources: copper leach solutions, wet-process phosphoric acid, Florida phosphate rock Leached zone, and Chattanooga Shale. These resources contain from 30,000 tons of recoverable U30, at a price of $7.52 per pound as a byproduct of copper leach solutions to 2,557,300 tons at a price of $69.32 per pound from Chattanooga Shale.

Jan 1, 1971

Abbey, Robert Graham, District Mgr., The W. W. Sly Mfg. Co., 50 Church St., New York, N. Y. '21 Abbott, A. N Ave. Morelos 84, Cuernavaca, Morelos, Mexico '23 Abbott, Argyle Campbell, Geol 42 Everett St., Arlington, Mass. '29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. '15 Abeel, George H., Jr., Cons. Min. Engr 1281/2 S. Canon Dr., Beverly Hills, Cal. '18 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh. .Pittsburgh, Pa. '28 Abel, Walter D., Cons. Engr 650 S. Grand Ave., Los Angeles, Cal. '82 Abele, Louis T., Min. & Met. Engr., Supt., Texas Hill Mine Coulterville, Cal. '31 Abell, Leo M. Millicent, S. Australia '31 Abernathy, George Elmer, Prof. of Geol. & Min., Kansas State Teachers College, Pittsburg, Kan. '20 Aborn, Robert H., Research Lab., U. S. Steel Corp. Lincoln Highway, Kearny, N. J. '19 Abozeid, Mahmood, Dept. of Mines & Quarries Cairo, Egypt '26

Jan 1, 1932

By H. Colijn

Belt conveyors have proven themselves for many years as a dependable and low cost method of handling bulk materials at high flow rates. The success of a belt conveyor system greatly depends on the initial loading of the material on the belt. If the material is loaded on the belt at the center, at approximately the same speed and with minimum impact, then most of all belt conveyor problems disappear. Proper belt loading is primarily determined by the engineering and design of the conveyor transfer point. This paper will establish and discuss some general design criteria required for proper loading and transfer of materials from one conveyor to another. Specific attention is given to loading points, chutes, skirt board length and general design of transfer structures.

Jan 1, 1971

By Charles H. Fulton

One of the first matters to receive attention from the Bureau of Mines when it was authorized to undertake investigations relating to wastes in the mineral industries was the smoke problem at smelting and ore-roasting plants. This bulletin is published by the bureau primarily for persons who seek information on the subject of metallurgical smoke but are unacqllainted with the technical language of metallurgy. It is, of course, not possible to free a techniCal subject entirely from teclmicalities, but, 80 far as possible, statements are made in plain and simple English. Metallurgical smoke causes considerable friction between the metallurgical industry and agriculture in certain parts of the country. Owners of smelting plants are making every effort to devise ways and means to do away with possible damage and annoyance from smoke and are meeting with success. The problem is peculiarly difficult in this country because of the large tonnages of material that must be handled. The solution of the problem is not yet at hand and much work still remains to be done. As the mineral industry is one of the great basic industries of the country and of necessity is entitled to full consideration, it should be accorded freedom to work out the smoke problem to the benefit of all concerned. The effort is made in this paper to present the problem of metallurgical smoke as it actually exists, without bias of any kind. The writer takes this opportunity to express his indebtedness to the sources of information on which he drew, many of which are enumerated in the selected bibliography at the end of this paper. In connection with the author's use of the present tense in describing plants and methods, the reader should note that none of the references in that bibliography is of later date than 1913. Much information was obtained by personal visits and by correspondence, and thanks are hereby tendered to all persons who kindly furnished data. The writer desires to thank particularly F. G. Cottrell, chief chemist of the Bureau of Mines, for criticism and comment.

Jan 1, 1915

THE opening session was held on Tuesday evening, February 17th, in the house of the American Society of Civil Engineers. The President of the Institute, Mr. E. B. Coxe, after a few introductory remarks, congratulating the members on the general prosperity in all the branches of the professions and manufactures represented by the Institute, called on Mr. E. F. Loiseau, of Philadelphia, for the first paper, On the Successful Manufacture of Compressed Fuel at Port Richmond, Philadelphia. Professor Prime called attention to the fact that the work of the United States Testing Board had been left unfinished at a point when valuable results had just been reached, and offered the following resolutions: WHEREAS, The American Institute of Mining Engineers has seen with regret that the work of the United States Testing Board has been suspended through the lack of an appropriation by Congress, which appropriation dues not seem likely to be renewed, and WHEREAS, It seems most important to the vital interests of our iron and steel manufactures that the experiments commenced by the United States Testing Board should be carried to successful completion ; Resolved, That a committee of three be appointed, to act with a like, committee to he appointed by the American Society of Civil Engineers, to carry out to completion the work commenced by the United States Testing Board. Resolved, That the American Society of Civil Engineers be requested to cooperate with this society by the appointment of a like committee. Resolved, That the committee have authority to request, in the name of the American Institute of Mining Engineers, contributions to a fund to be devoted to the completion of the experiments aforesaid. Resolved, That the Council of this Institute be authorized, whenever requested by the committee so appointed, to petition Congress for the free use of the testing machine at the United States Arsenal at Watertown. Resolved, That a committee be appointed by the President, to select the afore-said committee of experts. Resolved, That the President of the Institute have authority to fill any vacancies which may occur in the committee. The resolutions were unanimously adopted, and President Coxe appointed the following committee in accordance with the resolutions : Messrs. A. L. Holley, James Park, Jr., and J. F. Holloway. The President also appointed Messrs. Heinrich, Mickley, and Spils-

Jan 1, 1880

By Edward S. Hsia

Pluor Utah has been closely associated with the engineering and construction of earth bottom thickeners for porphyry copper operations, for the counter-current decantation circuit of a gold cyanide plant and similar applications in mineral processing. During the past 13 years, some 18 of these thickeners have entered service and the bottoms have proved to be watertight structures with no particular problems encountered. In the course of this work, technological advances have been realized in the procedures for engineering and construction of these units to assure watertight basins and achieve all possible economies in construction. This paper describes the successful application of engineering and construction techniques for a number of these thickeners.

Jan 1, 1977

By Jose A. Gomez, Javad Sattarvand

Failures of tailings dams have been happening lately. Due to the lack of laws on particular design criteria and stability requirements related monitoring during construction and maintenance, they are thought to be more fragile than hydraulic dams. Monitoring the dam is therefore necessary to understand its current condition and guarantee its safety. The physical condition of the dam could be evaluated with the early identification of seepage. Additionally, due to their adaptability and capacity for high-resolution data collecting, UAVs are an excellent choice for efficiently covering the tailings dam site. UAVs may capture high-quality photos when equipped with a high-resolution RGB camera, thermal sensors, or multispectral sensors. When these sensors are paired with image processing and machine learning algorithms, the result is a reliable estimate of the dam condition.

Jun 25, 2023

By G. M. Brownell

Introduction Within the past year a new deposit of gypsum has been opened up and brought into production in the Province of Manitoba. Until 1930, Manitoba's entire production came from Gypsumville, northwest of Winnipeg, at mile 161 on the Gypsumville branch of the Canadian National railway. However, during 1930 a gypsum bed was opened up at a point one mile south of the village of Amaranth, forty miles north of Portage la Paririe, on the west side of lake Manitoba (See Figure 1). Although no exposure has yet been discovered, the presence of gypsum below the surface in that district has been known for many years as the result of drilling for water. In 1929, J. R. Spear (1), of Winnipeg, interested some local capital in the possibility of .finding commercial deposits of gypsum, and, after some exploration work in the area with a well drill, the Amaranth deposit was located. Sixteen holes were put down at intervals of 400 or 500 feet, all of which encountered what appeared to be a continuous bed of gypsum, about thirty-eight feet thick, at a depth of 92 feet. The extent of the deposit has not yet been determined.

Jan 1, 1931

Taking the Presidential chair of the Australasian Institute of Mining Engineers, my first duty is to thank you for the high honour and position you have conferred on me. A position entailing the highest compliment the Institute could bestow on any of its members, and one which I feel my inability to properly fulfil, inasmuch, as you have men in your ranks of the highest scientific training residing on that great continent where the head quarters of the Institute is established, while my engagements here will not permit me leaving this colony but for a very limited period.About six years ago, during the time the mining boom was at its height, there came to this colony from England, Germany, and South Africa, several mining engineers, who in conjunction with the mining engineers here, formed an Institute which we soon found we were not able to maintain. The mining boom gradually died away, and many engineers have left the colony to find employment in other parts of the world. We made overtures to your Iqstitute to take us under your wing, which you were kind enough to do, and the outcome is that you have come over 1200 miles to hold a meeting in New Zealand. The paucity of members residing in this colony does not admit of a large attendance; but we heartily welcome you to our shores and hope you will enjoy a holiday visiting some of the principal mining centres and exchanging ideas, which not only improves our minds, and widens our field research, but also tends to lead to further economic improvements in the extraction of metals the earth contains...

Jan 1, 1903

R. C. BUCKETT (Lake View and Star Limited) : At the outset I should like to add my congratulations to those already extended to Mr..Norwood on his excellent paper, which has given us all an inspiration to strive further to improve our plant recoveries. In some respects this paper has left us so little to discuss without considerable time spent on. further research work. At all points one is met by a baffling array of facts which leave one feeling hesitant to speak.The careful and methodical way in which Mr. Norwood went along step by step until all channels of research presenting themselves were tested to his own satisfaction leaves me with but a few comments to make. Particularly striking to me is the explanation of the residual gold values in calcines by recrystallization of haematite and here is a line to be attacked by future studies. This will be mentioned again later.Particularizing on the paper, the first point that struck me was the method of change of pyrite through to the final haematite. I have never been able to satisfy myself that a sample taken from various positions along a roaster when cooled, as described on p. 397, represented a fair sample of the conditions at that point, but I must confess that I have not found a substitute that did satisfy me.However, the following figures are illuminating... But to fill dry a receptacle of known volume with calcines, as described by Mr. Norwood, gives the following apparentspecific gravities:

Jan 1, 1940

By H. G. Iverson

The effects of adding boron and boron plus carbon to electrorefined vanadium were evaluated with respect to mechanical properties at low temperatures and response to heat treatment. Grain size was significantly decreased with the addition of 0.05 percent boron, the decreases ranging from 30 percent at 800° C to 75 percent at 1,100° C. Increasing the boron content resulted in only a small increase in strength at room temperature, but at 77° K, boron contents of 0.005 to 0.076 percent increased the yield strength of vanadium over 50 percent, from 70,000 psi to 110,000 psi. When boron and carbon were present together, the individual grain-refining effects obtained with either element were retained. Approximately a twofold increase in strength was obtained by age-hardening the alloys containing both boron and carbon. Alloys with only boron additions did not age-harden.

Jan 1, 1968

By J. Ouellet

The design of hydrostatic liner for a deep potash mine shaft in Saskatchewan poses tremendous technological challenges. Technology has evolved to a point where one could consider a new innovative approach to hydrostatic liner design. But there is still a place for conventional technologies such as cast iron tubbings. As will be discussed in this paper, improvement to manufacturing process, installation procedures and even new materials can bring this technology to an excellent level of performance. With the spur of new projects in the potash industry of Saskatchewan, the authors worked in various shaft liner designs from the conceptual stage through to the construction phase. They were either directly leading the design work on some of these projects or acting as an external reviewer on others. Most of these shaft liner designs involved cast iron tubbing technology and ground freezing. The major challenge in sinking potash shafts in Saskatchewan is to go through a water-bearing ground formation under high pressure, known as the Blairmore or Manville fm. The only proven stabilizing technology for these formations is ground freezing. For a potash shaft, dry shaft conditions are highly desired, so a fully waterproof hydrostatic liner is required. All the existing potash mine shafts in Saskatchewan, except for two with composite steelconcrete lining, used the cast iron tubbing technology. Two new shaft tubbing liners have been constructed recently, one in the Athabasca Basin and one for a potash mine in Saskatchewan. When the authors began working on these new projects, what became quickly evident is that the technological knowhow for designing and constructing tubbing liners was no longer available within Canada and that the past construction methods used to sink tubbing lined shafts was obsolete. The tubbing liner for the shafts sunk in the sixties were designed either by German or British companies. In both of these countries only few tubbing lined shafts were sunk in last 40 years and the technology used in the sixties was not improved. There are only few countries where tubbing is routinely produced and installed: China, Russia, Ukraine and Poland. Out of these countries Poland is the one where this technology is the most advanced. The authors, working in close collaboration with engineers from Poland, attempted to rebuild this knowledge for the mining industry in Canada. This process involved thorough analysis of old technical reports, literature review and study of current polish design and construction practices as well as site visits of existing shafts. Through actual construction experience, some lessons were learned as well as ideas for improvements. In this paper, the authors will present a succinct review of design and procurement process. But, the practical aspects of the construction and installation methodology will be treated with more emphasis, more specifically the practice leading to good liner performance. Some of the poorly understood technical aspects of tubbing installation will be discussed more thoroughly and some currently accepted myths dispelled.

Aug 1, 2013