Search Documents

By C. Díaz, M. Barati

Prof. Torstein Utigard's untimely death, in the spring of 2012, put an abrupt end to a meritorious career in the field of high temperature chemical process metallurgy. As an academic in the Department of Materials Science and Engineering of the University of Toronto, Torstein made solid contributions to the advancement of knowledge pertaining to production and refining of both nonferrous and light metals, and to the development of inquisitive and innovative young people in extractive metallurgy. In this profile, the authors highlight aspects of Torstein's rich personality and of his contributions to his field of expertise.

Jan 1, 2015

By John A. Owsiany

The effect of longwall mining on streams and shallow aquifers has been the subject of numerous research studies for more than twenty years. As a result of these studies, it has become common to consider an overburden thickness of 400 feet as the lower limit at which longwall mining methods may be used with little or no effect on hydrologic systems. This paper presents the results of a study documenting the response of a large high order stream to shallow cover undermining by longwall methods in the northern Appalachian coalfield. The field site is located in a narrow stream valley where the overburden, composed primarily of limestone and sandstone units interbedded with shales and siltstones, ranges in thickness from 340 to 285 feet above the main bench of the Pittsburgh coal seam. Streamflow monitoring and monitor well measurements indicate that no significant loss zones or water table lowering resulted from undermining the stream or the adjacent valley bottom area. Additionally, hydrographs for shallow near-stream wells exhibit fluctuations related to natural seasonal variations, which are nearly identical to those observed in a non-undermined control well in the same watershed. Environmental factors affecting streamflow were monitored through the use of a control stream in an adjacent non-undermined watershed to differentiate between natural and mining induced changes in flow.

Jan 1, 2001

By Robert L. Lappi

This report covers the final phase of a project demonstrating the economic efficiency of cross-ridge mountaintop coal mining. A demonstration mine was established at Big Wheel Gap in northeastern Tennessee. Not only was cross-ridge mining feasible for the selected site, but parallel cut methods could not be used due to a deficit in available spoil storage. Cross-ridge mining permitted coal extraction at a cost almost identical with costs simulated by computer projections using mathematical optimization techniques. No unexpected environmental problems were encountered. Volume I is accompanied by Volume II which describes the MATHMINE Mine Simulation System, software used to support the mining demonstration.

Jan 1, 1984

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau's programs involved only health and safety research and education, and fuels testing. As the Federal Government's primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing mineral substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960's, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation's minerals, metals, and materials.

Jan 1, 1978

By D. Ksinsik, R. Boisvert, D. Leblanc

Casting, cooling and crushing/sieving of ferroalloys has followed a well-established pattern in the whole ferroalloys industry for many years. Usually liquid metal or alloys are cast into flat open moulds of various shapes and forms, and after solidification the product is removed from such mould to further cool down to a temperature where subsequent handling steps are feasible. Common to all mechanical product fractioning is the generation of dust and fine size material with lower product value. For almost 10 years, Bécancour Silicon has investigated alternative roads to improve technology and/or reduce or solve problems related to those disadvantages. Since 1995 Bécancour Silicon operates a special silicon granulation plant targeted to product for the chemical treatment/conversion of silicon for silicones production. Prior to the development of the granulation process, various systems had been evaluated, among others the vibrating casting bed, now in operation elsewhere but judged inappropriate because of the tapping volumes to be handled at Bécancour Silicon and other disadvantages. After evaluation of all aspects of heat transfer, radiation, and conductivity in relation to transfer media and within the product, a novel system was designed and built.

Jan 1, 2004

By Raden Haris Handayana, Jerri Mapanta, Eri Barlian, Milia Putri, Nasfryzal Carlo, Jihan Lubis

Waste oil is a growing problem throughout industries where environmentally responsible disposal ways are usually costly. There are many industries have developed process to reuse of waste oil as a source of energy on their own premises. Hanwha Mining Services Indonesia is one of blasting service that manufacturing explosive using waste oil. The usage of 60 % waste oil content in fuel solution already developed applied since 2020 at Petrosea-Kideco Site and will be increase until 100 % in 2022. The purpose of this research is to analyze the increasing of waste oil usage from 60 % to 100 % content at Petrosea Pit without reducing the emulsion quality and performance, and surely eliminate the fuel cost and reducing waste oil processing cost. Some trial conducted to determine the effect and quality of using 100 % waste oil content on emulsion at production blast. The method use to know the quality of 100% waste oil of emulsion is by direct application on bench blast. Using Microtrap VoD recorder, explosive energy will be recorded into m/s dimension, microtrap recorder the speed of explosive detonation in line with the speed of burning wire in the blast holes. The summarized of this research present that the using of 100 % waste oil content on emulsion can be applied on bench operation with the result of Velocity of Detonation (VoD) data is 4,559 mm/s, the mean of fragmentation size is in range 65.31 to 225.62 mm, the average of digging time on 1st layer is in range 10.2 to 11.6 s and on 2nd layer is in range 8.9 to 9.5 s, and the productivity still achieve on target. The result of all parameter quality still in the standard range of Hanwha and Petrosea.

Feb 6, 2023

By Donelson A. Robertson

Includes a review of the state-of-the-art of explosives loading in the crushed stone and cement industries of South Florida and the development of a field test program for alternatives. Emphasis is on the loading of small diameter (2 1/4" or less) explosives. Test results ire evaluated for operational and economic feasibility. Details are described of an explosives loading method which involves placing cardboard tubes with external couplings through the hollow drill steel and then Loading explosives into the tube casings after the drill rig has moved off. This method eliminates the hazards peculiar to loading explosives Through the kelly bar. The alternative method can be performed by existing drill rigs with or without minor modification. With modification, improvement in yield per blasthole and/or primary crushing rate provides opportunity so offset some or all of the additional cost.

Jan 1, 1978

By Mackenzie Burnett

An inducer-type pump, capable of injecting dry coal into a hydraulic transport pipeline has been developed and installed in a specially designed and fabricated slurry injector vehicle. The full scale prototype injector system can deliver up to 11 ton/min of coal into an 8-in pipeline t pressures up to 95 lb/in2. The Helical Inducer Injector operates on centrifugal principles with flow passing axially through helical pitched conical rotor. Water is delivered to the pump through an annular slot at the atmospheric pressure coal inlet. The spinning rotor maintains an air-core vortex of water which pressurizes the discharge housing. A screw feeds coal through the open inlet into this vortex. The inner radius of the vortex contracts as pressure is increased, giving a limiting maximum pressure which is proportional to the square of the rotor speed. Below this limit, flow rate, discharge pressure, und rotor speed re independent variables. The self-powered, 4 -in high slurry injector vehicle follows and receives ROM coal from a continuous miner, reduces the top size to 3-in, and delivers the sized coal to the injector feed screw for slurry formation and pumps it through a mobile hose attached to the vehicle's outby end.

Jan 1, 1983

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. They are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations.Cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance of having proper stability in cyclone operation while implementing any plant-wide optimization strategy.One of the key challenges in cyclone operation is that cyclones are highly sensitive to changes in operating conditions and are affected by process fluctuations such as feed pressure, solids concentration and flow rates. Fluctuations in cyclone feed characteristics lead to unstable cyclone performance which affects mineral liberation. For such an impactful unit operation, cyclones have historically been under-instrumented in an otherwise highly instrumented process plant. Traditionally, mill operators have relied on visual observations of the apex discharge to determine the operating state of the cyclones. Visual cues corresponding to the different cyclone operating conditions have been discussed by Neesse et al. (2004) as shown in Fig. 1."

Jan 1, 2014

By Samuel P. Harteis

Many mining operations rely on retention bulkheads to provide a barrier between impounded water and active mine workings. However, bulkhead failures can cause catastrophic flooding that puts the underground workforce at risk. Underground observations and evaluations of existing bulkheads indicate that a systems approach is required when building an underground water or slurry retention system. In addition to engineering the bulkhead, the designer must ensure the quality control of materials and workmanship of the bulkhead, the reaction of the mine strata when exposed to water under pressure, and methods to monitor the performance of the retention system. Researchers from the National Institute for Occupational Safety and Health (NIOSH), with the assistance of the Mine Safety and Health Administration (MSHA), conducted an extensive review of bulkhead permits submitted to the MSHA Technical Support office in Bruceton, PA. In addition, the researchers visited accessible bulkhead installations at undeground mining operations to gather information related to construction practices, maintenance issues, and monitoring and emergency response procedures. Several key items were identified that must be considered when permitting the installation of an underground fluid retention system.

Jan 1, 2008

By Agne Rustan

This paper is intended to give a summary of the first ten Symposia on Rock Fragmentation by Blasting where the symposia activities were governed by a Steering Committee replaced at Fragblast 2 by an International Organizing Committee (IOC). At Fragblast 9 the name was changed to Fragblast International Organizing Committee (FIOC). Eighty four pages of statistical data about Fragblast 1-10 is documented on the Fragblast Website (ISEE.org).

Jan 1, 2014

By AIME AIME

A LUSTY baby of the Institute, the Coal Division, showed that it had acquired a full set of teeth and was capable of man's work at the Division meeting at Fairmont, W. Va., on March 26 and 27. At this second of a series of field meetings, the first of which was held in Pittsburgh last fall, the industry in the East was represented from top to bottom and good humor and enthusiasm were the predominant notes. West Virginians are always good hosts and this meeting would have proved the statement to any inclined to doubt it. The spacious auditorium of the Fairmont Hotel was arranged for the technical sessions, the hotel being headquarters for the meeting. About a hundred and twenty-five representatives were registered and in attendance when Thomas G. Fear, chairman, opened the morning session at 10 o'clock Mr. Fear first introduced Howard Eavenson, vice-chairman of the morning program, who, as chairman of the Coal Division, had labored long and cheerfully to make the meeting successful. Mr. Eavenson talked briefly on what the organization was doing, pointing out that these field meetings were designed to bring the members into closer touch with the parent Institute and give the younger engineers in the field a better opportunity to participate in the work the Institute is doing. He congratulated the various committees for their work in promoting the meeting.

Jan 1, 1931

By Franziska Wolf, Rainer Ellmies, Helmut Mischo

"Mining is an important part of the economy of Namibia. In 2016, 11.1 percent of the GDP was the result of mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists of an underground mining operation.The global annual production of fluorspar is approximately 5.4 to 6.3 Mt (6 to 7 million st) (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu has produced on average about 45 kt/a (50,000 stpy) in recent years (U.S. Geological Survey National Minerals Information Center, 2015).The Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an openpit mine with four individual pits (A-D) since 1980. In 2014, the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently, Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village.The intent is to develop a concept for the further underground development of the mine. There are still about 6.3 Mt (7 million st) of measured resources left in the deposit, with an average grade of 27.5 percent CaF2. This study focuses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged.For solving the task to design the mine, a site visit for data collecting was conducted. Resource estimations were calculated based on existing drill data, and consequently, block models were created. The development of the mine design included the selection of the most suitable mining method, mining technology and mine organization. Moreover, some economic considerations are pointed out, followed by a profitability assessment."

Jan 2, 2018

By G. Herget

"A brief visit to European longwall mining operations in potash showed that retreating longwall mining provides a very attractive alternative to room-and pillar mining, especially in areas with bad roof, narrow seams and areas with high ground pressures. Mines de Potasse d'Alsace, France converted all potash operations to longwall mining in 1980. Recovery rates per panel vary between 75o/~ to 85% which compares very favourably with Saskatchewan values. Ground pressure in Saskatchewan are comparable to those of some of the deposits in Europe, but the presence of water in the hanging wall of Saskatchewan orebodies has to be given serious consideration. However, given the mining experience in Saskatchewan and the improved technology f or laboratory and field investigations, a review of present mining practice in Saskatchewan is desirable. IntroductionLongwall mining is practiced widely in coal mining and allows complete mechanization. It is applicable at great mining depth, in thin seams, weak roof and has been applied recently even to coal bed s dipping more than 65 degrees. Ideally this system allows complete extraction of an orebody. However, with high mechanization and emphasis on obtaining high outputs per man shift, extraction ratios rarely reach more than 80010 per panel.France, Spain and the U.S.S.R. have had longwall operations in potash for some time and a brief description is given below. Two of the operations were visited and the Russian operation is described based on German literature"

Jan 1, 1986

By T. A. Rickard

FROM AN OLD MANUSCRIPT THE text for this contribution to the history of the Patio process is a page taken from a Spanish manuscript of Bartholomé Arzaj Sanches y Uela, now in the possession of the library of Brown University (see Figure 1). I owe the photographic print to the courtesy of the librarian. The date, as will be seen, is 1577. The subject is the treatment of silver ores at Potosi, in old Peru, but in modern Bolivia. The group of drawings (see Figure 1) is entitled "Arrangement of the machines in which the ores of silver are ground on the bank of Potosi, the one of two batteries and the other of one". First, top-left, we have the sketch of a "machine of one battery" operated by a water-wheel. From this mill the water runs in part along an aqueduct supported by pillars to the two-battery mill and in part down the hillside, where men are at work with "tubs, which are called cochas, in which are washed the charges of ore and amalgam". Along the top of the page are shown the "various offices in which are stored the copper, the salt, the ucha [llama dung, used for fuel], the lime, and other materials for the re-duction of the ores". To the right of these are "apartments and warehouses in which is stored the ore brought down from the mountain"?the cerro de Potosi. Through the arched portal come the "sheep [llamas] on which is brought down the ore". To this is added a reference to "the second gate, which closes the whole works". On the level above the aqueduct are seen six men carrying skin-bags that contain water. This is being sprinkled on the ore. On the extreme right are six more of these water-carriers. Next comes the two-battery mill. The mortero, or mortar, is marked on the right. Another description says, "Stone, on which the stamps crush the ore, which is called a mortar". To the left of these are indicated "screens of wire in which the ore is sifted after it has been crushed". Farther to the left, near the ore-washers, is a "shed, in which is placed the metallurgist to test the ore of the boxes". Along the left side of the page are sundry buildings, one of which is labelled a "shed in which are placed the cones of silver". Near it, lower, to the right, is the "furnace, in which are roasted the sulphides to facilitate treatment". Farther to the right is the "place where the Indians mix the charges of sulphide ore, which is called a buitron". Alongside is a "buitron in which the charges are prepared for reduction". Inside is a container, to which are attached the words "measure, called topo" On the extreme right is "another buitron in which the Indians mix the ores with their feet, as well as the heaps for the preparation of the reduction". Near the bottom, on the extreme left, is the "chapel where the holy sacri¬fice of the mass is celebrated". Under the first buitron is the "place where they dry the moist ores, called pãpear".

Jan 1, 1935

Addressing community concerns in relation to an economic activity, particularly when it causes significant community impacts, is especially important for the development of extractive industry projects. Pipelines comprise an integral part of many hydrocarbon developments, which may cause different effects on local economic development, communities and the environment compared with open cast mines. This paper explores community impacts associated with a case study of the oil pipeline æEastern Siberia-Pacific OceanÆ in the Republic of Sakha (Yakutia), Russia. Based on semi-structured interviews, conducted in 2006 - 2008 in Russia, the paper investigates claims of local communities about potential impacts of the pipeline development of their environments and economic activities as well as community claims for greater involvement in sharing the benefits from this major infrastructure project. A community of Indigenous people, Evenk, is likely to be most profoundly affected by the development due to impacts on their traditional activities such as hunting and reindeer herding. The paper examines in detail the regional economic, social, environmental and Indigenous peoples concerns over the construction of the oil pipeline and investigates actions and methods adopted by community organisations to voice their concerns about the pipeline development. Finally, the paper assesses the process of interaction between the pipeline developers and regional stakeholders.

Jan 1, 2009

By Maria Flessas, Justin Ray, Danielle Steinmetz, Brian Zuckerman

"The Ventura County Medical Center Hospital Replacement Wing project consists of the construction of a 2- to 3-story building with a basement encompassing the entire footprint and two corridors connecting the new hospital wing to existing buildings. The site is located in the Ventura Basin where strong ground shaking has been observed during moderate to large earthquakes on nearby faults. The upper 90 feet of the soil consists of loose to medium dense finegrained sands and low plasticity silts that are potentially susceptible to liquefaction, seismic densification, and hydroconsolidation. Ground settlement associated with a large seismic event on a nearby fault is estimated at 20 to 26 inches. To account for the anticipated ground settlement, auger pressure grouted (APG) piles gaining support below the potentially liquefiable soil were selected for the support of the proposed structure. Challenges for pile design included the anticipated earthquake-induced ground settlement, high downdrag loads, low soil lateral capacity during strong ground shaking, and the effect of pile installation on the performance of the existing adjacent buildings and the installed shoring system. The replacement hospital is supported on over 600 APG piles, with lengths varying between 120 and 140 feet. Axial pile capacities were verified with an extensive indicator pile installation program and dynamic pile load testing.INTRODUCTIONThe Hospital Replacement Wing (HRW) project is at the Ventura County Medical Center (VCMC) in Ventura County, Southern California (Figure 1). The VCMC consists of three interconnected hospital buildings (Buildings 303, 304, and Fainer Building), the Medical Laboratory/Cafeteria Building, two mental health buildings, a medical office building, an emergency generator building, and surface parking lots. The HRW is near the center of the campus, adjacent to several existing buildings.The HRW is a 2- to 3-story structure, with a 15- to 20-foot-deep basement beneath the entire 95,000-square-foot building footprint. The HRW project includes a Loading Dock, a four-level corridor to the Fainer Building (Fainer connector), and a two-level corridor to the Medical Laboratory/Cafeteria Building (Café connector). The corridors are structurally separated from the existing buildings. Typical dead plus live load column loads for the HRW range from about 635 kips to 935 kips and total loads range from about 860 kips to 1,295 kips."

Jan 1, 2016

By K. M. Tompson, R. L. Armstrong, C. I. Godwin

"Tungsten skarn deposits on the Clea property in the Selwyn Mountains, Y. T., are related genetically to a quartz monzonite stock, about 500 metres in diameter at the surface. Lower Paleozoic sedimentary rocks are metamorphosed for a distance of 3 km from the stock. Tungsten-bearing skarn mineralization within the altered sedimentary rocks is of two types: sulphide-rich pods and calc-silicate beds. The most significant scheelite concentration is in calc-silicate beds near or adjacent to the quartz monzonite stock. Discordant K-Ar and Rb-Sr isotopic dates indicate that the stock is probably of early Late Cretaceous age, 94 Ma or slightly older, and that it cooled slowly. High initial 87Srl86Sr ratios and disequilibrium relationships between K-jeldspar phenocrysts and groundmass minerals in the porphyritic phase of the granitic rock , and between different granitic rock specimens, indicate contamination of crystallizing magma by old sialic continental crust which extends westward under the Selwyn Basin.This study is significant to regional tungsten exploration. Granitic rocks associated with tungsten deposits, in this part of the Canadian Cordillera at least, appear to have specific isotope characteristics that indicate they were generated at a specific time and in a particular way.IntroductionThe Clea tungsten skarn property (Fig. I) is owned by Canex Placer Limited, and lies in the Selwyn Mountains (Bostock, 1948) near the eastern margin of the Selwyn Basin (Wheeler and Gabrielse, 1972), Yukon Territory. The property covers a 20-square-mile area centered near latitude 62°47 ' north and longitude 129°52' west, and is accessible by helicopter. An airstrip and the terminus of a summer-use gravel road at MacMillan Pass, Yukon, are about 20 miles to the northnorthwest.This paper deals mainly with the geochronemetry of granitic rocks from a stock associated with tungsten mineralization on the Clea property. We show that these rocks have specific characteristics that not only define the genesis of this stock, but also have significance for regional tungsten exploration around plutons in the Canadian Cordillera."

Jan 1, 1980

This three-part report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the are handling stream. Oversize ore is causing much additional labor, creating work stoppages, and is a principal cause of accidents in metal mines. The specific objectives of the Present Systems Study were to determine and evaluate the productivity of existing ore handling systems in a representative group of underground metal mines, to relate the available historical accident record statistics of these selected mines to the specific operations in the overall ore handling operations, and to highlight the potential areas of improvement for each mine on the basis of productivity and associated hazardous index for each operation.

Jan 1, 1974

By Jorge Acosta Ale

"El presente texto señala la perspectiva de la producción peruana de cobre para la próxima década y su aporte económico en el Perú a través de un cuadro estadístico donde se observa un incremento de los pórfidos de Cuajone y Cerro verde en los años 70´, skarn de Tintaya en los 80´ y Antamina en el 2001. Así también se revisa el canon minero, regalías mineros y derechos de vigencia. "

Dec 1, 2016