Search Documents

By C. J. Bise, M. F. Sindelar

Regulations, such as the MINER Act of 2006, require the installation of redundant and secondary communication systems to assure that contact can be established with coal miners who may become trapped underground as a result of an event such as a fire, explosion or inundation. For half a century, the orientation towards underground communications has been that more complex systems better serve the coal miner. However, if a goal is to provide for an alternative means of establishing communication between the surface and trapped miners underground, then some of the technology employed should be simple, reliable and cost-effective. Coal mines spend hundreds of thousands of dollars on exploratory drillholes to characterize reserves, sometimes decades ahead of mine development. During the pre-mine planning phases, certain exploratory drillholes could be located and then outfitted with a simple communication link that would remain compatible with the continuing evolution of communication systems. Inexpensive links, whose locations would be accurately recorded, would be exposed by continuous miners during mine entry development, thereby allowing an underground phone to be connected to a surface station in the event of an emergency. A latent network of these communication links could be installed for less than $500 each, minimally affecting drilling and grouting operations, and could be designed to be compatible with many communication devices. This research examines methods and materials for incorporating an embedded communication link during pre-mine exploration drilling, addresses significant factors affecting its implementation, and presents a recommended design. Since mine plans are known to change, the objective is to minimize cost so that, if not used, the investment is minimal for a potential secondary means of communication between the surface and underground workings.

Jan 1, 2014

By M Schaffer, T Kewe, N Moffatt

Porgera mine is 95 per cent owned by Barrick Gold Corporation. It is located at an altitude of 2200–2700 m above sea level in the Enga province of Papua New Guinea and produces approximately 460 000 oz per annum with a proven and probable reserve of 6.2 Moz. The refractory ore is ground in a conventional semi-autogenous grinding and ball mill circuit. After the gravity gold is recovered, the slurry is floated, oxidised in the autoclaves and then leached. This paper will focus on the flotation circuit and the recent upgrade of the control system. The five interdependent flotation circuits were challenging for operations to control as they dealt with variable grade, throughput and circulating loads, as well as the physical limitations of the equipment. With the installation of 18 Portage Froth Characterization® (PFC) cameras, the plant’s operation has been converted from a level-control based strategy that was focused on individual cells to one that targets grade and recovery control across the entire circuit. Variability in feed and the corresponding launder issues were addressed with a unique site initiative of deflector plates to indicate filling level. Non-linear closed loop control was implemented directly in the DeltaV Distributed Control System (DCS) using Portage Advantage Regulatory Control (PARC) algorithms and optimised with AwaRE advanced controllers. The most noticeable benefits achieved with the upgrade include improved flotation gold recovery, consistent flotation sulfur grade and autoclave performance. Correspondingly, there was a significant drop in boiler diesel fuel usage and launder overflow conditions.CITATION:Kewe, T, Moffatt, N and Schaffer, M, 2014. Porgera flotation circuit upgrade and expert system installation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 345–356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By David B. Dill, Edgar R. Lea

The zinc deposits of the Balmat-Edwards Division of the St. Joseph Lead Company in northern New York State provide some 10 per cent of the domestic zinc produced annually within the United States. These complex ore deposits are contained within marbles of the Precambrian Grenville series, in a repetitive sequence of dolomites and silicated units. The Balmat ore bodies are localized at various intervals throughout some 1800 feet of the stratigraphic column on the northwest side of a band of gneiss that has continuity to the Edwards area, some 10 miles to the northeast. The Edwards ore bodies are located to the southeast of this gneiss. The marble formations are thought to have included repetitive intervals of marine sedimentation that provided mineralized source "beds" and were subsequently folded, flooded, and injected with melts at great depth and were sheared, recrystallized, and reconstituted. Detailed structural and stratigraphic studies throughout the northwestern Adirondacks, in the Balmat-Edwards district, and at each mine in particular indicate the close dependence of the ore deposits on the enveloping structure whether it be local, district-wide, or regional in scope. Primary folding has developed a northeast regional trend with northwest dips. Secondary folding has been developed by an almost horizontal northeast-southwest-oriented shear couple in the plane of the regional trend. The secondary folding has produced crossfolds that intersect the regional northeast trend and plunge north to northwest at various angles. The ore bodies are found within certain stratigraphic horizons where repeated alternation of competent and incompetent beds encouraged unusually complex folding. Analysis of individual mine structures indicates that the location of each deposit is controlled by structural crossing of primary and secondary folding. The ore bodies, which are tabular, lenticular, or pod-like in form, have features that suggest parallelism to true bedding or modified flow banding, developed by northeast-southwest shearing stresses related to the development of the crossfolds. The ore deposits in general follow both structural and recrystallization trends within the wall rocks. Mobilization of the pre-metamorphic ore minerals is believed to have involved a combination of plastic flow under stress and solution of the sphalerite, minor galena, and pyrite. The ore fluids are thought to have been guided by secondary shearing and microbrecciation into structurally prepared areas where reprecipitation took place. The presumed premetamorphic mineralization now exhibits epigenetic high-temperature features related to late-stage metamorphism.

Jan 1, 1968

By S. A. Diatchkov

There is a misconception that mineral-project economic evaluations in the former Soviet Union are either nonexistent or very limited. This is not the case. In fact, there are at least two basic methods that can be utilized to evaluate the vast mineral resources of the Commonwealth of Independent States (CIS). Evaluation procedures are based either on a comparison to known projects, which may rely on limited available data, or on potential-profit calculations, which generally uses more extensive databases. Significant philosophical differences between these systems and those utilized in the Western world include the following: •Under the centralized-government system, the economic evaluation of a mineral project was based on artificially determined mineral prices and costs. Every ten to 12 years, prices for concentrates and metals were established by the Council of Ministers and remained unchanged until the next reconsideration of prices .

Jan 1, 1995

By H. C. Gunning

Introduction The invitation to contribute a discussion on some of the broader features of the mineral deposits of our Cordillera seemed acceptable enough when presented several months ago. More mature consideration has impressed upon me the difficulty of making any constructive or very helpful contribution in the short time available and with my limited inspiration. Dr. Lang deserves our real gratitude for his general paper of nineteen pages at the beginning of the Volume. Into it, with the help of two diagrams and seven tabular summaries, he has packed a lot of useful information and has analyzed along several lines the data of the Volume's twenty-eight detailed papers on our mines and camps. He has added additional facts from his own knowledge of the region. I am sure that, like myself and the whole fraternity, he feels especially grateful to the eleven company geologists who found time to contribute detailed descriptions of mines they have studied. The Regional Situation With the Jubilee Volume and two recent publications of great value from the Geological Survey, we are more up-to-date on Cordilleran geology than we have ever been. But I would like to emphasize that we still have but fragmentary information. Brief study of G.S.C. Map 932A will illustrate this. Our knowledge of the Rocky mountains is limited to two narrow sections along the main railway lines, a somewhat larger area from the border north along the Mesozoic coal-bearing basins, and some reconnaissance along Peace river and the Alaska highway. There is some additional information on old maps, particularly those by G. M. Dawson, but it is very much of the 'exploratory' type. The other mapped areas are chiefly in the accessible region south of 'fifty-one', in the central part adjacent to and spreading north, recently, from the Canadian National railway, and along the edges of the Coast Range.

Jan 1, 1950

By J. A. de Carvalho Junior

This paper analyses the impact of the uncertainty associated with the input parameters in a mine planning optimization model. A real example was considered to aid in the building of a mathematical model that represents the coal production process with reference to the mining, processing, and marketing of coal. This model was optimized using the linear programming concept whereby the best solution was perturbed by the stochastic behaviuor of one of the main parameters involved in the production process. The analysis of the results obtained permitted an evaluation of the risk associated with the best solution due to the uncertainty in the input parameters.

Jan 1, 2012

By H. S. Kalman

A table of factors, for rapid, accurate calculation of the volume of pure helium in cylindrical steel containers, is presented. By use of the table the volume of helium in a container, at base conditions of 14.7 psia and 70° F, can be calculated from the observed pressure and temperature of the helium and the known internal volume of the container. The table covers a pressure range from 0 to 4,500 psia in 10 psi increments and a temperature range of 0° to 120° F in 2° increments. The calculation of volume requires a single multiplication, using a factor from the table and the known internal volume of the container. A discussion and evaluation of the accuracy obtainable and a derivation of the formula used (which takes into account compressibility of helium, thermal expansion of steel containers, and the stretch of steel due to internal pressure) are presented. An example showing how the table can be used is given also.

Jan 1, 1963

By Jupneek Singh, Zachary A. Kiehl, Leila Safazadeh, Gareth Kennedy, Eleonora Widzyk-Capehart, Jeremy W. Ward

Mine workers are continuously exposed to a host of nonfatal stressors and potentially fatal hazards: noise exposure, excessive vibration, poor air quality, toxicant exposure, ignition of combustible gases, equipment-related accidents, and thermal heat stress. Wearable or portable sensors and contextual analytics provide a platform to unobtrusively collect and fuse multimodal health and safety data in real time to compute both acute safety and longitudinal health insights. This paper presents preliminary trial results, conducted by Simtars, VigiLife, Inc., and Queensland Mines Rescue Service, of the application of wearable sensors to monitor heat stress and other vital biometrics for mines rescue personnel.

Feb 1, 2024

By E. H. Jr. Dix

THE use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong-aluminum alloys, magnesium is present to the extent of ½ to ¾ per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth1, 2,3,4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high purity aluminum manufactured by this company .5

Jan 1, 1929

By Scott W. Hazen

This report describes exploration for lead-zinc ores at the Madonna mine between 1945 and 1953 by the Utze Lode Co., the Bureau of Mines, and the company with Government financial aid under the Defense Production Act of 1950. The Madonna mine yielded silver, lead, and zinc with a net smelter value of over $5,000.000. from 1882 to 1924. The mine was inactive from 1924 to 1942 when the Utze Lode Co. acquired the property. Possibilities for finding ore in the mine, especially at depth, were considered favorable. The Utze Lode Co. began rehabilitating the Madonna mine in 1945. An exploration program, which consisted of winze sinking and drifting, failed to produce commercial are.

Jan 1, 1956

By Eugene T. Sheridan

The 22d annual survey of the packaged-fuel industry by the Bureau of Mines, United States Department of the Interior, revealed that 26 plants in 8 States were in operation and reported production in 1956. The demand for packaged fuel in the United States has declined gradually since the end of World War II, and the number of operating plants has decreased from 70 in 1946 to 26 in 1956. Annual productive capacity of the industry has decreased also during this period, and the decrease in capacity was about proportional to the decrease in operating plants. Packaged-fuel plants are relatively small, and 85 percent of the active plants in 1956 had an annual capacity of less than 10,000 tons. The same situation prevailed in 1946, when 84 percent of the plants had a capacity of less than 10,000 tons. Total capacity for the 26 active plants in 1956 was 174,600 tons, an average of 6,715 tons per plant. Operating rates in 1956 were the highest since 1951, and the rate of production for the industry averaged 37 percent of capacity.

Jan 1, 1958

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

"The JKMRC researchers have been redeveloping the suite of breakage testing techniques to more realistically align with the breakage environment in comminution equipment. Computational modelling, especially with the DEM, has highlighted the modes of impact and contact, along with the energies of these interactions in a wide range of equipment. This has driven the need to match these modes in laboratory ore characterisation tests. The objective has been to build a continuum of breakage tests and associated models that span the required range of breakage forces and environments. The ore sample is subjected to a sequence of tests covering: abrasion (surface breakage) of angular through to smoothed particles; single particle impact from high energy single impact breakage down to low energy; incremental breakage covering 60 mm down to 50 µm particles; particle strength distribution; and bed breakage over a range of compression and energy input. These tests are suited to multi-component ores with a distribution of strengths. A modelling technique is also being developed to utilise primary breakage for modelling breakage under different types of confinement. This paper draws together these techniques, previously published by the authors, into a coherent whole. The suite of tests is approaching the point where a fixed set of tests can be used to model the performance of a full range of equipment, removing the need to conduct repeat ore characterisation tests for each different piece of equipment incorporated in a circuit design. This path should open up the application of different circuit configurations and novel equipment in comminution circuit design.1 INTRODUCTION Comminution modelling utilizes a wide range of ore characterisation techniques and methods to deal with the range of comminution equipment available for production use. In general, the tests have been designed to correlate with specific pieces of equipment, using calibration factors to provide the link between the small-scale test and industrial-scale performance. The majority of tests focus on estimating the power requirement of process equipment to achieve a desired throughput and grind size. Overall, this approach has achieved acceptable outcomes in the past, but the reality is that equipment sizing suffers from considerable uncertainty, in excess of ±20% is not uncommon. This uncertainty is covered by safety margins and automatic scaling factors in equipment selection. In striving to improve reliability, the industry tends to add more adjustment factors to the tests, and design margin rather than question the basic validity of the testing process. As the tests are often correlated to production equipment via carefully guarded databases, they are also locked into historic operating inefficiency, not providing direction or revealing opportunities to improve production efficiency in comminution equipment or circuits. Safe in the knowledge that they are achieving the expected production based on test work predictions, a site is unlikely to set their sights on reducing specific energy consumption by 10%."

Jan 1, 2018

By W. Collingwood

As openpit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in openpit mines is often recirculatory. This recirculation traps dust and gases in deep openpit mines. This problem is particularly acute in high-latitude openpit mines, due to a phenomenon known as atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In openpit mines, this can result in unhealthy accumulations of gases and other contaminants. In this study, the natural wind flow patterns in and around openpit mines were investigated using a computational fluid dynamics (CfD) program. Two-dimensional models were created for a variety of pit geometries. The effect of depth, slope angle and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2012

By R B. Stewart

Where pasture production is the intended land use of the areas to be reclaimed, the creation of a suitable growing +medium is a major objective. To achieve this land reclaimers require a sound understanding of the proposed mining plan and a knowledge of the physical, biological and chemical properties of materials intended for resurfacing disturbed areas. Where the original soil is not being replaced in its natural state, research is usually required to determine an alternative growing medium. Results from field research conducted on waste material from the Waihi Gold mine are reported with emphasis on the significance of soil depth in relation to pasture production in this environment.  Problems in extrapolating field research to large scale operations are also considered.   Essentially the requirements for successful pasture production, on surrogate growing medium, are akin to conventional approaches used in New Zealand in the development of unimproved agricultural land. High inputs of fertiliser are initially needed, especially where volcanic soil is used, and careful management of pastures and soils is required to minimise soil erosion and create a sustainable system. In the first three to five years of pasture production, grazing use of the land requires to be dictated by pasture availability and soil conditions and not by animal feed requirements. The use of light stock (young dairy or sheep) is recommended.   Successful land restoration requires a team approach by a range of cooperative specialists including engineers, soil scientists, farm managers, agricultural contractors, landscape architects and environmental officers.

Jan 1, 1991

By J. R. Donald

Electric arc furnace (EAF) dust, which can be considered as a by-product of the steel recycling process, contains significant quantities of recoverable zinc and iron, as well as hazardous elements such as cadmium, lead and chromium, which can be leached by ground water. The zinc in the EAF dust is found almost entirely in the form of either zinc oxide or zinc ferrite, the latter accounting for 20 to 50 percent of the total zinc. It is important that an efficient process be developed which renders the dust inert, while reclaiming the valuable metals to off-set processing costs. During the conventional carbothermic reduction processes, iron is formed, and this iron can participate in the reduction of the zinc oxide in zinc ferrite. In the present work, the reduction of the zinc oxide in zinc ferrite by iron according to the following reaction: ZnO-Fe2O3(s,s) + 2 Fe(s) = Zn(g) + 4 FeO(s) was studied in an argon atmosphere using a thennogravimetric technique. First, a thermodynamic analysis was performed using the F*A*C*T computational system. Then, the effects of briquette aspect ratio (lid), temperature, zinc ferrite particle size, amount of iron added, as well as additions such as lime, sodium chloride, and calcium fluoride were investigated. It was found that, initially, the reaction was chemically controlled with an activation energy of 178.1 kJ/mol. Then, after a product layer had formed on the outer surface of the briquette, the reaction was restricted by the diffusion of zinc gas away from the reaction interface. The parabolic rate law was fitted to the experimental data, and the parabolic rate constant was found to be: = -6.2275 + 0.0054 T (K)

Jan 1, 1995

By Frederic Chavan, Hans Jakob Windier, Shane Yanagisawa, Willy Ritz

The Zurichberg twin track tunnel is the main segment of the Swiss Federal Railway's new expressline. A heavy concrete lining with a circular cross-section was chosen to cope with the swelling tendency of the surrounding rock. The 4,356 m (14,300 ft) long, 11.52 m (38 ft) diameter tunnel was driven using a shielded Robbins TBM. A 1.20 m (4 ft) wide, 25 cm (10 in) thick precast lining was placed from within the shield tail as the excavation progressed. Tunnel excavation and initial lining operation were completed in 18 months, averaging 11.86 m/day (40 ft/day) in two nine hour shifts. After breaking through, the final 28 cm (11 in) thick concrete arch lining was cast in place.

Jan 1, 1989

By M. A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

Jan 1, 2009

By J. C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert,1,2 Russell,9 Le Conte,4 Spurr,5 Louderback,8 and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea. More recent syntheses of the geologic history have been prepared by Lindgren,7 Ransome,8 Nolan,9 Bill-ingsley and Locke,30 Longwell,11 and Eardley.12 The tentative nature of the present interpretation, which treats the structural evolution of the Utah and Nevada area, must be considered in light of the scarcity of geologic information from the province as a whole. The methods of interpreting tectonic history from stratigraphy are based largely on the concepts of Marshal Kay.23 Discussions with Hoover Mackin also have aided in organizing the Tertiary history. TECTONIC AND STRATIGRAPHIC SETTING Two approaches to the subject of the tectonic history are possible; they correspond to looking through opposite ends of a pair of binoculars. One involves an expansion and extension of detailed work and the other an interpretation based on regional geological relationships. It is believed that the second approach, used here, is not in disagreement with detailed observations. The area of the Basin and Range Province is shown in Fig. 1. Within this area middle Tertiary to Recent high-angle faulting has controlled development of mountain ranges and valleys. Only the part of the area north of Las Vegas, Nev., and south of the Snake River in Idaho will be considered in this article. Within this part of the province most of the ranges trend north-south. Approximately two thirds of the area is covered by late Tertiary to Recent valley fill and lake deposits.

Jan 1, 1961

By K. Liddell

Current practice for the recovery of platinum group metals (PGM) from flotation concentrates is by energy-intensive smelting processes followed by separation and refining of the base and precious metals. Energy costs are rapidly increasing in South Africa and this trend is forecast to continue in future years. Moreover, the smelting operations are highly susceptible to deleterious constituents, particularly chromite; and the increasing tonnages of UG2 chromititic ore being mined results in an increasing chromite content of smelter feeds. Hence there is a substantial incentive to assess and implement alternative processes to smelting for the treatment of PGM concentrates. The Kell process is a patented hydrometallurgical alternative to smelting that is totally insensitive to the chromite content of the feed concentrate and comprises three commercially proven unit operations (pressure oxidation leaching of base metals and sulfur, roasting and chlorination of precious metals). The Kell process provides the opportunity for existing and new PGM producers to significantly reduce their energy consumption, and in particular their consumption of electricity, by removing the need to smelt PGM concentrates. Energy costs, greenhouse gas emissions and installed power requirements are also much reduced. Compared with smelting and refining these reductions are calculated as: ? Total energy consumption-50% reduction ? Electrical energy consumption-84% reduction ? Energy consumption costs-76% reduction ? C02 emissions-70% reduction ? Installed power requirement 92% reduction. The data obtained from simple laboratory batch amenability testing can be readily applied to the Simulus mass and energy balance simulation procedure to determine energy and reagent consumptions, equipment selection and process optimization. The applicability of Kell to treating low-grade 'dirty' concentrates with high UG2 content as well as to polymetallic concentrates containing base metals as the major payable metals with subordinate PGM means that these savings can also be expected when the process is used for treating a range of concentrate types and grades. Keywords PGM,UG2, Merensky, smelting, chromite, electricity, hydrometallurgy, Kell Process, Eskom.

Jan 1, 2011