Search Documents

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983

By J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

"The Niobec concentrator rejects up to /5% of the Nb as slimes (-10u.m). The recovery of Nb from these slimes by column flotation is being studied. An essential condition for selective flotation is slimes dispersion. A particle size analyzer, the Sedigraph 5000D, was used to monitor dispersion in plant waters with combinations of organic and inorganic dispersants and flotation reagents. Flotation reagents were particularly detrimental to dispersion with sodium silicate. The best dispersion conditions were selected for column flotation tests. These tests revealed that reagent combination had a pronounced effect on froth stability. Careful frother selection achieved good froth stability under conditions of good dispersion. Plant water increased the required dispersant concentration causing mineral depression.IntroductionSlimes (-10 u.m) rejected at Niobec contain up to 15070 of the over-all Nb content . Recovery of Nb from these slimes would significantly increase over-all recovery. A suggested recovery route involves two phases: (1) carbonate flotation (to remove most of the carbonates) depressing silicates and pyrochlore (as currently done at Niobec); and (2) selective (direct) pyrochlore flotation from the silicates. Phase 2 has been addressed and several routes to achieve selective flotation are available. Phase I was attempted with the selective reagent scheme used at Niobec but a considerable amount of pyrochlore floated with the carbonates due to poor slimes dispersion."

Jan 1, 1987

By J. H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) amended the Federal Mine Safety and Health Act of 1977 to improve the safety of mines. The MINER Act established a Technical Study Panel (the Panel) to provide independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant materials in underground coal mining (1). Because frictional heating is a common cause of belt fires, the Panel recommended that the Mine Safety and Health Administration (MSHA) evaluate the drum friction test to determine if such a test would contribute to conveyor belt safety beyond that provided by the Belt Evaluation Laboratory Test (BELT). This paper compares the results of the drum friction test to results from the BELT and large-scale tests for six different conveyor belts. The results are used to evaluate the drum friction test as a method to determine the fire resistance of conveyor belts.

Jan 1, 2011

By K. Hanson

When done properly, benchmarking is an extremely effective tool for assessing ones performance, finding areas for improvement, and identifying strengths. However, when done improperly it can be an exercise in futility and result in incorrect observations and conclusions. A primary pitfall of benchmarking is collecting too much unreliable information. Surprisingly, the evolution of data storage and the ease of data collection are not helping with better data collection. Instead, it is just allowing one to collect more information, while at the same time inundating one with too much data. Additionally, the process of data collection can be tedious and is often times delegated to the least experienced individual resulting in unreliable and incorrect data collection and entry. Another primary pitfall of benchmarking is metrics that are cost based or poorly designed. Cost based metrics typically involve comparing unit mining costs ($/tonne). Between mines, unit mining costs are not very well correlated and have become further complicated by significant regional cost variations and mining inflation in the last years. Likewise, poorly designed metrics lead to poor benchmarking results. Examples of poorly defined metrics include: metrics that rely on information that is difficult to collect, metrics that are poorly defined, metrics which are too site focused, and metrics that measure low consequence practices.

Jan 1, 2011

By Jr. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to Maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required.

Jan 1, 1933

By D Craw

The Old Man Range, south of Alexandra, in central Otago consists of a package of highly folded greenschist facies schist of the Wanaka lithologic association. The range is crosscut by several east to ENE-striking high angle gold-bearing quartz veins, (eg Whites Reef and Grays Reef), which were extensively worked in the late 1800s. The range is bounded on its east side by the Old Man Fault, which separates these rocks from generally flat lying and planar Caples Terrane schist. To the west of the Old Man Fault, about halfway up the range, a large subparallel, 100 m wide fault zone strikes NNW and appears to cut off the historic veins. The fault zone consists of highly sheared and folded rocks and numerous high angle cataclasites and centimetre-scale clay gouge zones. Hydrothermal alteration is not apparent and the individual faults and shears are clay altered, possibly due to weathering, without visible quartz veins. Gold, limonite pseudomorphs after pyrite and rutile are concentrated in some of the narrow cataclasites and gouge zones. These mineralised structures are texturally similar to the gold-bearing reefs and may be structurally related. It is postulated that the NNW-striking shear zone and ENE-striking veins may be a conjugate array formed during a period of Cretaceous normal faulting.

Jan 1, 2004

By T. Reed Woodbridge

The object of this paper is to bring to notice a method in use at the Cedar Point laboratory of Witherbees, Sherman & Co., for determining the phosphorus in the ore mined at Mineville, N. Y. This ore is magnetite, with a gangue containing crystals of apatite. In 1886, Mr. H. F. Dawes, then head chemist at the works, suggested that as all the phosphorus seemed to be in the apatite, it could be obtained in solution by dilute nitric acid. After some experimenting the following method was adopted, and has proved invaluable for rapidity and ease; half a dozen determinations requiring very little more time or trouble than one. From + to 10 grammes of ore are weighed into a 150 c.c. beaker; 50 C.C. hot water and 10 c.c. strong nitric acid are added; the beaker is covered and the contents are boiled for 1/2 hour (10 minutes sometimes proves sufficient; but 4 hour is safer). The bumping which ensues if more than & gramme is used need cause no trouble. The hot solution is filtered into a 250 C.C. beaker. The filtration and washing (with hot water) proceed rapidly, as the magnetite itself is but slightly acted upon. After the addition of 15 C.C. ammonia and 15 c.c. nitric acid, the solution is cooled to 45' C., and from 15 to 40 C.C. of molybdic acid solution is added and stirred vigorously. In 5 minutes the precipitate will be down, and the determination can be finished by any good method. At Cedar Point the method more commonly used is weighing as yellow salt. Good washed filter-paper is used, No. 0 Swedish being preferred; and dozen 3 1/2-inch filters are numbered and dried and weighed at 110°C. These are always kept in stock. The yellow salt is filtered on one of these, washed with dilute nitric acid (2 per cent. by volume); dried for 1 hour at 110' C., and then weighed, 1.63 per cent. of weight being calculated as phosphorus. The filters vary in the two weighings from

Jan 1, 1889

By Gus Pantages, Bernard D. Blaustein, Charles Zahn, Irving Wender

Oils from coal hydrogenation have been examined at the Bureau of Mines to learn whether any centers of the optical activity reported in coal would survive catalytic hydrogenation at 450-525 ° C and about 8,000 psig pressure , and , if so , to obtain information about the nature of the active products . Oils from carbonization tars also were examined . Optical activity was found in the majority of the distillate fractions of the hydrogenation oils and in almost all distillates from the carbonization tars . No activity was observed in the tar - acid and tar - base fractions examined . Methods for isolating optically active concentrates included distillation through a packed column , liquid chromatography on silica gel , and adduction with urea . For the materials so processed , the optical activity segregated mainly in the paraffin - naphthenic and the hydroaromatic fractions . Although the specific compounds responsible for the optical activity were not isolated , experimental and spectrometric findings indicate that alkylsubstituted cycloalkane , cycloalkene , and hydroaromatic structures are most likely responsible for the optical activity of the concentrates . The optically active centers probably derived mainly from the steroids and terpenes in the biological materials that participated in the formation of coal .

Jan 1, 1964

By Richard F. Link, George S. Koch

Through the use of statistical methods, estimates of metal content and tonnage of an ore body made by using data from 18 diamond-drill holes are compared with actual values established with data from 1,829 drift samples. The reliability of the estimates made from the drill holes is assessed in several ways. The relationship of metal content (assay-width product) to grade is explained. It is concluded that useful estimates can be made from 18 drill holes provided that reasonable assumptions are made and certain risks accepted. The ore body investigated is the Don Tomas vein of the Frisco mine, San Francisco del Oro, Chihuahua, Mexico.

Jan 1, 1964

By A. N. Veltmeyer

"INTRODUCTIONTeck-Corona Operating Corporation's David Bell Mine is located 35 Km east of Marathon, Ontario. In conjunction with its 1000 tonne per day gold concentrator, the company operates an effluent treatment plant for the treatment of mill, mine and site effluents prior to environmental discharge. This paper provides a brief overview of treatment strategies and methods, employed to detoxify final effluent.WATER MANAGEMENTThe tailings impoundment basin, located 3 Km south of the plant site, provides storage capacity for all process effluents and site run-off. Basin supernatant (reclaim water) is recirculated to the plant for reuse as process water, in order to minimize fresh water consumption. As site run-off and limited fresh water intake exceed natural losses due to evaporation, reclaim water in excess of process requirements is passed through the effluent treatment (ET) facility to control tailings basin level by providing regulated discharge of environmentally acceptable effluent. (Figure 1)PASSIVE TREATMENTTo reduce treatment costs and burden on the ET facility, reclaim water is fed to the plant to take maximum advantage of natural destruction processes occurring in the tailings basin.These include: volatilizationphotodecompositionbiological oxidation and precipitationstorm water dilutionConcentrator recovery techniques (Figure 2) are directed toward maximizing gold recovery while limiting the addition and extraction of contaminants requiring disposal and eventual treatment.Currently ore ground to 90% -200 mesh is pre-aerated at pH 9.0 with lime for 18 hours prior to 30 hours cyanidation at pH 9.5 with low cyanide ion excess (70 ppm).Pre-aeration passivates cyanicides prior to cyanide contact. This reduces cyanide consumption and the formation of cyanide complexes. In conjunction with recovery requirements low pH is maintained to retard the dissolution of stibnite into its antimony and sulfide components."

Jan 1, 1989

By D. R. Tesarik

As part of its research program to investigate ways of improving resource recovery and reducing subsidence, researchers from the U.S. Bureau of Mines placed instruments in the B-North ore body of the Cannon Mine, Wenatchee, WA, to monitor cemented backfill and rock deformation during mining. The vibrating-wire gauges proved to be reliable and versatile, and approximately half of the instruments are providing data after 2 years of use. A two-dimensional, finite-element model was used to analyze the Cannon Mine's multilevel bench cut-and-fill mining method and predict rock and backfill displacements. The model accurately predicted rock displacements, but the predicted and measured displacements in cemented backfill had a correlation coefficient near zero, indicating that the model should only be used to predict rock displacements and not backfill displacements. A finite-difference model was also used to evaluate the stability of a cemented backfill pillar. Results can be used to conservatively predict backfill stresses, but on-site observation of pillar failures coupled with in situ measurements are needed to make more accurate predictions. An ongoing evaluation of the mining system has indicated that filling the primary stopes tight to the back with cemented backfill allowed these pillars to carry overburden loads soon after the cemented backfill was placed.

Jan 1, 2010

By Roger S. Jackson

"This study interprets vibrations produced by single underground shots, recorded on surface by 135 digital seismographs laid out in four linear arrays. Several vibration anomalies were observed and are investigated. A novel method of displaying the blast-induced vibration iso-contour data relative to the three-dimensional representations of the geological rock units and structures leads to the following interpretations:• The identified faults commonly dampen or amplify vibrations, on the evidence of the peak particle velocity,• Strong anisotropy of geologic formations produces different vibration attenuation in the various directions of interest,• Low-vibration “depressions” can be related to the presence of faults, and• Higher vibration levels than expected based on ‘scaled-distance’ principles are observed close to intersecting faults.The interpretations from this study document a better understanding of the geotechnical influences on blast induced stress wave propagation in a geologically complex area. The practical benefit of this understanding is better control of surface vibrations, experienced from underground mining activities."

Jan 1, 2010

By Joseph L. Ritchey

The Trail Lake RARE II area comprises 1,300 acres (526 ha) in Lassen and Plumas Counties, California, adjacent to the Caribou wilderness. No mining claims, prospects, or quarries are reported within the study areas, and no evidence of potential mineral deposits was found during a field reconnaissance. Quaternary basaltic lava flows uniformly underlie the area. INTRODUCTION The Trail Lake (No. B5-095) RARE II further planning area occupies 1,300 acres (526 ha) adjacent to the Caribou Wilderness in Lassen and Plumas Counties, California. Susanville is about 30 mi (50 km) east and Chester is about 17 mi (27 km) south of the study area. Access from State Highways 44 and 36 is provided by well-maintained gravel roads.

Jan 1, 1981

By S. L. Crouch

An important class of mining problems involves excavations in planar seam or vein-type deposits. In many instances it can be assumed that the seam is at 'infinite' depth in a homogeneous, isotropic or transversely isotropic, linearly elastic rock mss, and that the normal to the plane of the seam is a principal stress direction. Rational planning of excavations in such deposits requires a knowledge; of the stresses and displacements induced by complicated, irregular excavation geometries in the plane of the seam. This problem previously has been solved either numerically or by means of an electrical resistance network analog. Both of these methods effectively simulate the mined portions of the seam as a dislocation in an otherwise continuous mass, and determine the complete solution in terms of the stresses and displacements at the seam. In both cases, the plane of the seam is divided into a number - say, M x N - of squares, and the solution to the problem is determined in terms of the solution to an M x N system of equations. The numerical approach requires that these equations be solved explicitly, while the analog; solves them instantaneously with current analogous to stress and voltage to displacement. A purely numerical solution of practical problems can require a substantial amount of computer time, particularly in situations that demand some sort of sequential analysis, either due to successive mining or to nonlinear behavior of the seam material. This report describes a combined analog-digital computer system for solving problems that are impractical when either device is used separately. The digital computer and the analog are interfaced so that the digital computer can receive information from the analog via a switching matrix and an analog to digital converter, and can activate points of the analog via another switching matrix and a set of digital to analog converters. The resulting hybrid system can be used to simulate arbitrary "stress-strain" characteristics for any portion of the seam by an iterative procedure similar to the initial strain method used in nonlinear finite element analysis. Thus, the hybrid system combines the speed of analog computation with the decision-making capability of the digital computer: the analog instantaneously solves the set of equations, and the digital computer decides how the initial strains must be altered for the solution to be compatible with the prescribed "stress-strain" characteristics for the seam material. The hybrid computer system has many implications for rational planning of underground excavations, since it allows practically any type of inelastic seam behavior or artificial support characteristics to be simulated. Inelastic seam behavior, for example, might be due to either rock failure or to time-dependent deformation.

Jan 1, 1974

By N Cusworth, W R. Mackenzie

"In 2007, the authors presented a framework for the conduct of resource project feasibility studies and provided guidance on minimum standards and best practice (Mackenzie and Cusworth, 2007).This paper will present the authors’ observations in relation to feasibility studies undertaken to support investments made during the unprecedented period of resource project capital investment since 2007. It will also provide comments on general trends in the mining industry’s approach to project assessment and update recommendations on best practice.CITATION:Mackenzie, W R and Cusworth, N, 2016. The use and abuse of feasibility studies – has anything changed?, in Proceedings Project Evaluation 2016, pp 133–148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By C. V. Jude

This U. S. Bureau of Mines (USBM) report presents results of stress analyses and field observations to investigate the effects of elevated trench drifts on the structural stability of rock mass zones surrounding a production draw drift in a mine utilizing a mechanized load-haul-dump (LHD) trench undercut panel caving system. A two-dimensional boundary-element mine stress model was developed to predict the locations and extent of damaged rock mass zones surrounding draw drifts where adjacent, parallel trench drifts are either elevated or not elevated above the LHD production draw drift level. A Mohr-Coulomb shear-failure criterion was obtained directly from in situ borehole shear test data. Hock-Brown shear-failure parameter values were computed from borehole-shear and triaxial test data. A procedure is described to estimate these parameters when a rock mass rating (RMR) value and triaxial data on intact samples exist, and no borehole shear test data exist Results indicate that trench drifts, elevated to the level equal to the height of the LHD production draw drift, would not minimize material damage nor significantly enhance the stability of rib and crown pillar zones surrounding production draw drifts in the mechanized LHD trench undercut caving panel investigated at this mine.

Jan 1, 2010

By J. C. Watts

Monitoring and control of conventional industrial wet grinding circuits is conceptually straightforward. However, since production objectives and operating constraints can vary widely from plant to plant, there is probably no single overall grinding circuit control strategy which is "best" in all cases; in-variably some compromise is necessary between performance desired under ideal conditions and performance achievable in practice. The recent advent of relatively low cost, reliable, high speed small computer systems is revolutionizing daily operations in increasing numbers of metallurgical processing plants. Of special power and capability is a hierarchical computer network like that currently in use at the Pinto Valley Operations of the Cities Service Company. Several satellite processors for key plant areas communicate with a master computer operating under a powerful multitasking real-time operating system. Hardware and software structure is such that downtime on one of the processors -including the master -does not have a major impact on overall system operation. Admittedly, the powerful, core efficient table driven satellite software, which handles process/computer communication, calculation of nonmeasured process variables, and basic Direct Digital Control functions, is difficult to modify. However, important high level process monitoring, report preparation, graphic display, and supervisory control functions -including economic optimization -can be implemented by project engineers at the plant site. Thus, for example, new control strategies can be quickly examined and rapidly evaluated. Such computer monitoring capability also permits use of short duration process pulse tests for approximate dynamic modeling and rapid calculation of controller tuning constants for single loop dominant systems. Following a brief back-ground discussion of the Pinto Valley Project, we present some of the more interesting results and conclusions of our work over the past year.

Jan 1, 1978

By William K. Cunningham

The investigation described in this report was begun as part of the Bureau of Mines progress to develop acid processes for the extraction of alumina from low-grade bauxite and. clays. A domestic shortage of high-grade bauxite sui table for treatment by the Bayer process became acute as a result of' World War II; an intensive search for a practical acid process using lower-grade alumina-bearing raw materials was therefore warranted. The laboratory development was described in a preceding Bureau of Mines publication wherein the basic theory for the design and erection of a pilot plant maybe found. A 2-ton-per-day continuous pilot plant was constructed and successfully operated at College Park, Md., which demonstrated conclusively the chemical and mechanical feasibility of a solvent purification process for aluminum sulfate. The estimated production cost of $38.64 indicates that under present market conditions the process would not be economically feasible.

Jan 1, 1948

By R. J. Baumgartner

Sustainability issues are from rising interest and importance for the mineral industry worldwide. In order to bring them into management processes and to improve decision processes, economic, ecological and social aspects of products, services or technologies have to be assessed. In this paper, the concept of integrated sustainability assessment is presented. Each aspect is assessed with quantitative or qualitative methods. The results of these ecological, social and economic sub-assessments are integrated by the means of Fuzzy Logic in order to regard preferences of decision maker and circumstances of decision situation. An example demonstrates the application of this new instrument.

Jan 1, 2005

By Maureen M. Foss

Underground coal mining is hazardous due to changing geological conditions. One geophysical method showing promise for in-seam hazard detection is ground-penetrating radar (GPR). The Bureau of Mines recently completed preliminary studies to demonstrate the feasibility of using GPR for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using trans-illumination. Data were gathered on multiple travel paths, and a back projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomographic tech-nique, and the results were compared with those of the actual data. Analysis of the tomographic images shows the presence of the clay vein, although its boundaries are unclear due to the tomography method used. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take. A need has been shown for research involving more sophisticated tomography techniques, transmission studies on thicker coal seams, and reflection studies using the synthetic-pulse system.

Jan 1, 1987