Search Documents

By J D. Grobler

In the heavy minerals industry wet high intensity magnetic separators (WHIMS) are widely applied for primary magnetic separation of magnetic minerals and non-magnetic minerals. This piece of equipment is well known for its robustness to handle a wide range of feed conditions and still produce stable product qualities and yields. A heavy mineral production plant aimed to increase production through their WHIMS plant containing 11 duties and 26 units. Instead of adding new units an alternative approach was followed to firstly maximise the efficiency of the current circuit and secondly to consider possible reconfiguration of the circuit to produce additional product tons for minimal capital investment. In order to characterise the current circuit’s efficiency, identify pockets of excellence and determine the areas for improvement the whole circuit was surveyed several times and mineral mass balances were drawn up.This paper aims to: discuss the modelling process of the WHIMS circuit,explain the calibration and validation process followed to ensure the accuracy, anddemonstrate the sensitivity analysis performed on the different options. From this analysis an efficiency criteria was developed to compare different circuit configurations that enabled the production plant personnel to make an informed decision on the way forward.

Oct 5, 2011

To enable ammonium nitrate-fuel oil (AN-FO) to be used on an equal weight basis with nitroglycerine explosives, smaller diameter bore holes became necessary with consequent modifications to drill steel and burden on holes. Detonation of AN-FO in small diameter holes proved successful both with and without primer charges but some alterations were required to adapt anoloders to the smaller holes.Important factors in training all operators in the new charging method were the retention of improved fragmentation, avoidance of excessive overbreak and keeping wall rock dilution to an absolute minimum. The successful storage of ammonium nitrate in climatic conditions with daily temperature fluctuations above and below the critical 90°F has been achieved.INTRODUCTIONTechnical aspects of ammonium nitrate-fuel oil (AN-Fa) blasting agent are well covered in recent literature. This paper deals primarily with the manner of its introduction as the principal explosive underground at Great Boulder Gold Mines Ltd. and with the many problems encountered in the process. Following reasonably successful experimental firings in June 1962', using granular ammonium nitrate and an anoloder, permission was granted by theWestern Australian Mines Department to carry out test work in selected areas of the mine. The permit allowed for fuse firing only, and for a mixture of AN-Fa containing between 5t and 6 per cent fuel oil, with an adequate primer.The use of AN-Fa on an equal weight basis with nitroglycerine explosives, involved smaller diameter holes with alteration to ground burden and modification to drill steel.Initial tests indicated that it was apparent that AN-Fa could not replace gelignite on an equal weight basis if the...

Jan 1, 1965

By Richard Quirk

This report describes methods and techniques employed by The Glidden Co. of Cleveland, Ohio, in explorating an ilmenite-bearing sand deposit in Ocean County, New Jersey, during 1960 to determine ore reserve potential and the feasibility of mining and establishing a milling plant on the property for the production of ilmenite concentrate. The property covered approximately 1,250 acres. Comprehensive sampling by water-jet drilling indicated the deposit averaged 20 feet in thickness and contained 4.5 percent heavy minerals, of which 80 to 85 percent was ilmenite and leucoxene. Average depth of the water table as determined by auger boring was 16.8 feet. Pilot plant tests indicated that circular concentrators in combination with spiral concentrators would recover at least 80 percent of the heavy mineral content of the sands. It was estimated that sufficient ore reserve tonnage had been developed to supply the company's Baltimore chemicals division, pigments department, with a suitable grade ilmenite concentrate for a period of 20 years at the present rate of pigments production. The property was designated as Lakehurst mine and plans are in progress for mining development and plant construction.

Jan 1, 1963

By Michael Stanwood

Project feasibility no longer involves just technical and economic viability-today's feasibility study must include environmental, regulatory, and political considerations as well. While the US now appears at least somewhat committed to developing synthetic fuels, including oil shale, it is the environmental issues, rules, regulations, and guidelines that will play the major role in determining the timing, magnitude, and overall scope of synfuel development in the coming years. The key environmental obstacle affecting oil shale development is uncertainty. Although oil shale may be the most environmentally studied "new" technology in the world, little is known with much degree of certainty about potential environmental consequences of one full-scale commercial facility, or the effects of a massive development effort in a relatively pristine and sparsely populated area. Other primary environmental uncertainties include: • Environmental compliance costs and their effects on investment decisions; • The reliability and acceptability of anticipated pollution control technologies; and • The confusing, time-consuming environmental regulatory framework, which requires more than 100 permits, clearances, and reviews before development occurs. This discussion will focus on the latter uncertainty, and will describe he current status of potential constraints to oil shale industry development in five areas: water availability; water quality degradation; air quality degradation; reclamation and spent shale disposal; and community impacts.

Jan 1, 1981

By Magued G. Iskander

The deterioration of concrete, steel, and timber is a serious hindrance to construction in marine and corrosive environments. Composite materials such as fiber-reinforced polymers (FRP) can offer performance advantages for construction in these environments. In the last decade, piling made of FRP composites has been used experimentally throughout North America. However, composites face obstacles because they do not have a long track-record of use in civil engineering structures. A comprehensive review of the current experience in research, testing, design, and practice of composite piling is presented in this paper.

Jan 1, 2002

By Henri Carrat

La Geoquímica es una ciencia que estudia la abundancia, la distribución y la migración de elementos químicos en la litósfera, hidrósfera y atmósfera. En ese sentido, el presente texto refiere los métodos utilizados en la prospección geoquímica, así como los procesos que implica. También se muestran los fenómenos desarrollados (dispersiones), métodos, el caso particular del uranio y la prospección química realizada en el C..E. A.

Jan 1, 1963

By Torn H. Okabe

A fundamental study was conducted with the purpose of establishing an environmentally sound recovery process for recycling of valuable metals, by combining scraps containing such metals. As an example, direct extraction and recovery of neodymium (Nd) in magnet scraps was investigated by utilizing liquid metal as an extraction medium. It was found that liquid magnesium (Mg) is a suitable extraction medium and can extract Nd from iron alloys with high efficiency at around I 100 K. The newly developed extraction apparatus for Nd is a mechanically simple and static device without moving parts, where the Mg extraction medium circulates due to differences in the temperature inside the reaction vessel. This developed device can simultaneously accomplish continuous extraction of metal Nd from scraps, re-extraction of Mg from Mg-Nd alloy and the eventual recovery of pure Mg. As a result, metal Nd with 98 % purity was directly recovered from magnet scraps under certain conditions. It was also shown that the extraction agent Mg could be reused. The results of this investigation show the possibility of establishing a new process for the direct extraction of Nd in pure metal form without oxidization.

Jan 1, 2003

By Cushwa, C. C.

AT the Park Utah Mine, labor costs of stoping A have been reduced from 30 to 40 per cent. by the use of double-drum hoists and scrapers. The application of scrapers varies with the methods of timbering. In stopes, which must be timbered with square-sets or stringer sets, one method is used; another is used in wide orebodies that can be held open until filling is introduced; and still another in narrow flat veins. Nearly all the oreshoots at the Park Utah lie at less than 50" from the horizontal, and most of the ore is difficult to handle through flat chutes. Proper care is probably the most important requisite for successful scraping, as serviceable equipment can be obtained from several manufacturers. One capable mechanic, therefore, was put in charge of the scraper hoists. He visits every stope daily, oiling hoists and tail1 blocks, inspects all equipment, splices cables and changes "set-ups" when necessary; his pay has been a good investment. The Park Utah now has in use ten double-drum Turbinair hoists, and one Sullivan double-drum a. c. hoist of the same capacity and outside design as the air hoists. The electric hoist is slower than the air hoists and does not pass large boulders easily; it is, however, a very effective machine. The air hoists are fast, powerful and

Jan 1, 1925

By Saulo Brinco Diniz

O presente trabalho buscou explorar a influência de um tratamento térmico de ressolubilização, realizados com distintos tempos (70, 80 e 90 minutos) a uma temperatura de 510ºC, na microestrutura e na dureza de uma liga de alumínio 7475- T7351. Para verificar a influência destes tratamentos térmicos foram utilizados um durômetro (fabricante EMCOTEST, modelo Duravision 300) e um microscópio óptico (Olympus, modelo GX51). Após os resultados obtidos, pode-se evidenciar que a liga de alumínio em estudo sofre um envelhecimento natural (a temperatura ambiente), e dentre os tempos de encharque estudados, 70 minutos é o tempo que possivelmente obtém-se a maior ressolubilização dos precipitados.

Aug 17, 2017

By Julius G. Chang

Against the receding background of the October stock market crash and the December overhang of inventories, the economy began with a shaky start in 1988. As 1988 began, the Administration's estimate of real growth for 1988 had just been reduced from 3.5% to 2.4% and economists and other ob-servers were concerned that the expansion that was 5 years old might be near the end and that a recession might be around the corner. The ensuing moderately strong economic activity, however, belied all the negative signals that were evident earlier, and the real GNP continued to grow at an estimated 2.3% annual rate during the first quarter of 1988, extending the ongoing recovery into the sixth year (table 1.). The relatively accommodative policy of the Federal Reserve Board (the discount rate was cut by 0.25% in January), a strong performance by the export sector, and the revival of consumer spending were major forces underlying the economic strength. But as the quarter drew to a close, signs of tight capacity utilizations were apparent in many of the export and capital goods sectors, including textile, chemical, plastic, metal, and machinery. Employment was at a record high level while the unemployment rate was close to a historical low. Prices were rising at a faster pace than those of 1987, and the dollar resumed its slide after a brief recovery in January and February. These factors gave rise to the fears of higher inflation. Long-term interest rates increased, casting a pall over the prospect of a robust growth for the rest of the year.

Jan 1, 1988

By J. D. Morgan

Introduction In 1986, the US economy passed the $4 trillion mark. However, the value of domestically processed materials of mineral origin fell slightly to $240 billion. The value of metals produced from US ores was unchanged at $5.6 billion, as was recycled scrap at $4 billion, while the value of industrial minerals rose slightly to $17.9 billion. Consumer demand strongly affects mining and the US economy is relatively saturated with longlived products. Moreover, in recent years there has been a steady increase in consumer, mortgage, and federal debt, inhibiting new purchases of goods. Motor vehicles and housing are major traditional markets for mineral materials. However, the 242 million US citizens already possess 170 million licensed motor vehicles and 92 million dwelling units. In 1986, domestic motor vehicle production fell 3%, to 11.3 million units, while new housing starts rose slightly to 1.8 million units. Nearly all mineral commodities move relatively freely in world trade. As detailed in Figs. 1 and 2, in the last three decades world production of major mineral materials has greatly increased. At present, substantial excess productive capacity exists not only in the US but also in many other countries. Consequently, the US mineral industry is encountering increasing competition from other sources, along with increasing competition from newer, engineered materials. For example, US production of plas¬tics has risen from 900 kt (1 million st) in 1950 to 22.7 Mt (25 million st) in 1986 - on a volume basis significantly greater than steel. Plastics, too, are mineral-based materials, some 7% of petrochemicals going to their manufacture. 1986 saw increased calls for protection. But President Reagan, in his 1987 State of the Union Message and Economic Report to the Congress, reaffirmed adherence to a policy of free and fair trade. However, he stressed the need for increased efforts to open foreign markets to US exports and to increase competitiveness of US industry US imports of mineral-based minerals in 1986 were valued at $40 billion and exports at $24 billion. Strategic minerals As detailed in Fig. 3, imports supplied a significant proportion of total US consumption of several important materials, including many classified as "strategic and critical." There were no changes in stockpile policy during the year. Congress debated the President's 1985 proposals to reduce stocks of World War II-type materials and to focus more on high technology materials needed for the cutting edge of future military material. But no final action resulted. However, Congressional concern about apartheid in South Africa did result in increasing pressure to limit imports of South African minerals. Meanwhile, the National Critical Materials Council in the Executive Office of the President intensified its efforts to be better able to advise the President. The Defense Production Act provides authority for priorities and allocations, supply expansions, voluntary agreements, and

Jan 5, 1987

Gold, silver and palladium may be separated from the other base metals and sulphur contained in copper sulphide precipitates derived from the Sherritt-Gordon nickel process using a process involving an oxidation roast, a reduction roast and a Cu(II)/acetonitrile leach. Sulphur is removed as SO, in an oxidation roast and the hot calcine is reduced with carbon, or with carbon plus cuprous chloride. The resulting product contains metallic copper which is readily dissolved with cupric ions in aqueous acetonitrile solution. Copper powder is recovered by thermal disproportionation. The residue contains the bulk of the iron and precious metals and may be treated by a number of methods, including direct cyanidation or melting with suitable fluxes. Melting the residue will produce a copper alloy containing the precious metals and remove the iron as a slag. The alloy can be recycled to the copper leaching stage or sent for toll refining depending on the precious metal content. Impurities from the leaching circuit are controlled by a bleed circuit which in one approach utilizes the SO, from the calciner to produce Chevreul's salt and separates copper from the soluble cobalt and nickel. Alternatively, the bleed may be directed back to the main refinery copper boil stage or oxydrolysis stage.

Jan 1, 1982

By Torn H. Okabe

A fundamental study was conducted with the purpose of establishing an environmentally sound recovery process for recycling of valuable metals, by combining scraps containing such metals. As an example, direct extraction and recovery of neodymium (Nd) in magnet scraps was investigated by utilizing liquid metal as an extraction medium. It was found that liquid magnesium (Mg) is a suitable extraction medium and can extract Nd from iron alloys with high efficiency at around 1100 K. The newly developed extraction apparatus for Nd is a mechanically simple and static device without moving parts, where the Mg extraction medium circulates due to differences in the temperature inside the reaction vessel. This developed device can simultaneously accomplish continuous extraction of metal Nd from scraps, re-extraction of Mg from Mg-Nd alloy and the eventual recovery of pure Mg. As a result, metal Nd with 98 % purity was directly recovered from magnet scraps under certain conditions. It was also shown that the extraction agent Mg could be reused. The results of this investigation show the possibility of establishing a new process for the direct extraction of Nd in pure metal form without oxidization.

Jan 1, 2003

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel-economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By Thiago Guimarães Teixeira

Produtos químicos são os ingredientes essenciais para os processos de tratamento de águas e efluentes. A GDU consome mais de 30 produtos químicos diferentes utilizados em suas 17 estações de tratamento de água e efluentes distribuídas em toda a Usina Presidente Vargas (UPV). A gestão dos estoques dos produtos químicos, acompanhada do consumo padrão de cada um, contribuem para a garantia da qualidade da água tratada e no custo de tratamento de cada ETE. Por outro lado, a falta ou a deficiência de um sistema de gerenciamento acarreta em descontroles dos parâmetros de qualidade da água e aumenta custos por imprevisibilidades no processo, podendo inclusive causar danos aos processos clientes. O grupo em conjunto implantou um sistema de gerenciamento visual dos estoques de produtos químicos em cada área de sua responsabilidade, pois foi evidenciado muitas ocorrências de descontrole da qualidade da água devido à falta de produtos químicos na área, e como consequência, elevados pedidos de produtos químicos em emergência. A principal ação tomada para a implantação desse sistema de gerenciamento de produtos químicos foi estabelecer, por meio de gráficos de controle, um sistema de gerenciamento visual, permitindo conhecer, acompanhar e prever o consumo e data de novos pedidos. Dentre os benefícios da implantação deste trabalho, podemos citar: a) Efetivação dos pedidos de produtos químicos com antecedência; b) Entregas programadas na data de necessidade, com estabelecimento de nível de estoque de segurança de produto nas áreas; c) Redução do número de solicitações de produtos químicos em emergências; d) Envolvimento dos operadores nos consumos e controles de estoques de produtos químicos, através do sistema de gerenciamento; e) Parâmetros de qualidade da água estabilizados; f) Redução do risco de interferência nos clientes por má qualidade da água; g) Redução de desperdícios; h) Custos evitados com transportes e multas ambientais.

Aug 17, 2017

By Solange Kazue Utimura

As placas de circuito impresso (PCIs) dos resíduos eletroeletrônicos (REEEs) possuem diversos metais na composição. A recuperação desses metais tem incentivado as pesquisas inovadoras no seu processo de extração. Como alternativa de recuperação de metais das PCIs de forma sustentável optou-se pela biohidrometalurgia envolvendo a fase extração. O presente trabalho avalia a biolixiviação do cobre na presença de duas cepas bacterianas distintas em PCIs de REEEs provenientes de impressoras obsoletas. As PCIs foram caracterizadas mediante as técnicas analíticas de espectrometria ICP-OES e de fluorescência de Raios X (FRX) para determinar os elementos químicos presentes na amostra inicial. As cepas utilizadas na lixiviação bacteriana foram Acidithiobacillus ferrooxidans (AF) e Leptospirillum ferrooxidans (LF), cultivadas em meio de cultura T&K. Os ensaios de biolixiviação foram realizados em incubadora orbital, com velocidade de rotação de 170 rpm, temperatura de 30 oC, volume de inoculo de 10% (v/v) e densidade de polpa de 30g/L. A técnica empregada na concentração de cobre da solução após a biolixiviação foi a FRX. Foi possível determinar que a cepa AF apresentou uma extração de 100% de cobre em 8 dias em comparação com a LF na qual foi observado que a extração de cobre foi de 100% em 5 dias.

Oct 30, 2017

By Juliana Gonçalves Pohlmann

A redução das emissões de CO2 pela substituição parcial de carvões por um combustível renovável como a biomassa é um assunto de crescente interesse na siderurgia. As emissões de CO2 na etapa de redução podem ser reduzidas pelo uso de biomassa como combustível ou pela queima em condições de oxi-combustão. Este trabalho visa investigar a combustibilidade de eucaliptos termicamente tratados em laboratório em atmosferas convencional (O2/N2) e de oxi-combustão (O2/CO2), comparando com uma moinha de carvão vegetal e carvões típicos do processo de injeção em altos-fornos (PCI). Os testes de combustibilidade foram conduzidos em um forno de queda livre (DTF) a 1.300°C com diferentes proporções de O2/N2 e O2/CO2. Os chars do DTF foram caracterizados quanto à aparência ao microscópio, área superficial e reatividade. Os eucaliptos termicamente tratados apresentaram as maiores combustibilidades, seguidos pela moinha e pelos carvões. Os chars das biomassas apresentaram estruturas mais reativas do que os chars dos carvões, e maiores áreas superficiais e reatividades. As poucas diferenças de combustibilidade e reatividade devido à atmosfera de oxi-combustão indicaram que, se aplicada ao alto-forno, esta tecnologia pode não ocasionar efeitos negativos no comportamento de carvões e biomassas.

Aug 16, 2017

By Lyn Jones, Mike Bratty, Rick Lawrence, David Kratochvil

"The treatment of water is required at many mining operations to remove metals and prevent the discharge of contaminated water to the environment. In other cases, water treatment is used to provide better quality water for recycle to the processing plant, or to process bleed streams in hydrometallurgical operations in order to prevent deterioration in metallurgical performance or process equipment. BioteQ Environmental Technologies Inc. has developed and commercialized the BioSulphide® Process which can provide an alternative for these treatment needs and which can also be used for profitable metal recovery, particularly in cases where conventional metal winning techniques are not economical. The BioSulphide® Process is a high rate anaerobic biotechnology for on-site production of H2S from sulphur species, although for smaller flows and metal loadings, the use of chemical sulphide reagent might be more cost effective. Both new projects and existing commercial operations, used for removal and/or recovery of copper, nickel, and zinc, and which range in sulphide generating capacity from 50 kg/day to 3.7 tonnes/day, are discussed. Particular focus is placed on the results of operations at the Raglan Mine in Northern Quebec where dissolved nickel is removed from contaminated water at a high efficiency through the precipitation of nickel sulphide. Plant effluent is discharged directly to the receiving environment and the high-grade nickel sulphide product is combined with the nickel flotation concentrate produced at the mine. The plant at Raglan will replace the existing conventional water treatment plant and will eliminate the need for on-site storage of treatment plant sludge.INTRODUCTIONThe BioSulphide® Process, which produces low cost H2S for use in selective metal precipitation, offers a low capital cost alternative which can operate efficiently and cost-effectively within a wide range of flows and solution grades. Since the technology can be used to recover metals from solutions with low flows and metal grades, the technology is also applicable to environmental applications for water treatment, with the sale of recovered metals providing an offset to treatment costs. For environmental control, the technology has a distinct advantage in being able to meet strict effluent discharge criteria due to the very low solubility of metal sulphides. To date, BioteQ Environmental Technologies has designed and constructed three plants for metal sulphide precipitation, with another three projects in the advanced development stage."

Jan 1, 2006

By Matheus Porto Trindade, Marcos Menino de Macedo Filho, Isau de Souza Alves Junior, Sandro Griza, Brenno Lima Nascimento, Gustavo Dória Lima

O tratamento de oxidação térmica da liga Ti-6Al-4V foi realizado ao ar a 600 °C durante 2h, 5h e 10 h. O comportamento à fadiga foi analisado e comparado com aquele da liga não tratada. Foi feita caracterização através de análise por microscopia ótica e eletrônica, difração de raios-x e medição da rugosidade. Os resultados do DRX demonstraram crescimento dos picos de rutilo. Verificou-se um aumento na espessura média da camada formada de 0,12 μm para 1,09 μm ao elevar a duração do tratamento de 2 para 10 h. Os resultados apontaram redução de resistência a fadiga de 35 % para amostras oxidadas durante 2 h, 27 % para amostras oxidadas por 5 h e 29 % para as amostras tratadas durante 10 h, em relação ao ensaio com corpos de prova não submetidos ao tratamento. O efeito prejudicial causado pela camada formada após oxidação de 2 h foi tão danoso quanto o causado pela camada formada após 10 h, apesar da diferença entre as espessuras das camadas. A morfologia encontrada nas amostras fraturadas indicou fragilização na superfície das amostras oxidadas, contribuindo para a nucleação de trincas iniciais nos primeiros ciclos de fadiga na camada que favoreceram a propagação de fadiga, independendo da espessura de camada.

Oct 19, 2019

By Gustavo Eduardo Praes

A Samarco Mineração S.A., nos últimos anos estudou diversas alternativas para a substituição dos combustíveis fósseis por combustíveis renováveis (Biomassa) em seus fornos de pelotização tipo “Traveling Grate” (grelha móvel). Avaliou-se o uso de carvões vegetais, de eucalipto e de capim elefante, em substituição total ao antracito na composição da mistura. Estudou-se gaseificação em planta piloto, foi realizado um modelamento computacional do uso de gás de síntese e a comparação com os combustíveis tradicionais utilizados em fornos de pelotização de grelha móvel da Samarco. Os trabalhos iniciais foram realizados em escala de laboratório (Pot Grate). Em 2014 foi realizado um teste industrial, com um combustor de biomassa piloto acoplado ao duto que direciona o ar quente para a região de secagem ascendente do forno 02 da Samarco Mineração S.A. O teste ocorreu entre 27 de janeiro a 21 de julho de 2014. Realizou-se uma avaliação detalhada da engenharia deste sistema e de seus impactos no forno de pelotização. O combustor consiste em um sistema para queima de biomassa, o qual gera os gases quentes a serem introduzidos no sistema. Dependendo da configuração, o sistema poderá elevar a temperatura dos gases de secagem em até 75°C, quando comparado a uma situação de referência.

Aug 16, 2017