Search Documents

By J. E. Fraley

This report describes the preliminary results of a Bureau program to develop and test an inexpensive grout for full-column support of roof bolts. Various inorganic grouts were tested in both cartridge and slurry form. Tests were also performed on methods of water packaging and on the effect of fillers on the grout strength. Results showed that some grouts had poor early strength and exceptional mid-to long-term strength. Laboratory tests have shown that rapid-setting inorganic grout could be an economical replacement for resin bolts if the short-term strength could be increased. Further development to improve its early strength would need to be tested in the laboratory and underground to prove its potential for the mining industry.

Jan 1, 1987

By P. Nicholls

Though the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more common types. No new investigational data are included, but the deductions are largely based on a recent publication of the U.S. Bureau of Mines'. Definition of Types There are three primary types of fuel beds: (I) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown .resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed horizontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1936

By P. Nicholls

Though the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more common types. No new investigational data are included, but the deductions are largely based on a recent publication of the U.S. Bureau of Mines'. Definition of Types There are three primary types of fuel beds: (I) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown .resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed horizontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1936

By T N. Little

The grade control process undertaken at mines aims to maximise the value of the ore (valuable product) mined and fed downstream for processing or sale. The full range of grade control activities includes: reserve estimating, drilling/sampling, assaying, modelling, ore block design, blasting, ore mark out, excavating, stockpiling, processing and reconciling. Over the last 25 years, the grade control process has undergone significant improvements and this is in part due to the developments in grade control blasting. This paper discusses the development and classification of grade control blasting applications in surface mining. A review by the author in 1988 (Little and van Rooyen, 1988) is used as a benchmark for discussing the very significant progress that has been made.Two major technology initiatives have enabled this development. The first was the development of a method for the measurement and analysis of total displacement during the blasting process. Currently, the Blast Movement Monitor (BMM®) is a practical tool that has been used around the world to improve the industry’s understanding of three-dimensional blast movement dynamics. The second technological enabler was the development of electronic detonator systems. The unique aspects of electronic detonating systems are their higher accuracy and that all detonators are activated at time zero (initiation). From a grade control blasting perspective these features and other improvements allow experimentation and, ultimately, more complex, multiobjective blasts to be designed and implemented.This paper reports on a classification and review study undertaken by the author. In all, five selective blasting methods and nine bulk blasting methods are classified and reviewed. Five important observations are made: there is value in classifying the range of grade control blasting strategies, and the blasting objective framework presented is helpful in this regard the range of strategies available to designers is increasing as enabling technology develops, so too do the ambitions of blast designers and the expectations of downstream customersgrade control blasting and Mine to Mill concepts are merging, and this paper caters for this trend using multiple blasting objectiveshaving a technical primary blasting objectives framework, combined with the classification system presented here, should assist practitioners and stakeholders with lateral thinking in regards to future technological innovations, grade control blasting and Mine to Mill initiatives.CITATION:Little, T N, 2015. Classification and development in grade control blasting for surface mines, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 343–354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C. W. Davis

This paper is the second of a series of progress reports on a study, of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States. There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value. One ,of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although Several manganese minerals acre readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.§. Recent experiments have shown that a roast at 650 to 900°C converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution. Introduction of smelter gases containing as much as 5 per cent SO2 during such a roast would not add much to the cost of the operation and might result in the formation of considerable water-soluble manganese sulphate.

Jan 1, 1930

By W. R. K. Wu

This bulletin traces the development of high-pressure, coal and tar hydrogenation technology, based on an intensive review of the pertinent literature. The bulletin was written as a part of the Bureau of Mines research program on synthetic liquid fuels. It covers the history and economics of the process; the chemical aspect of hydrogenation of coal, tar, and middle oil; the engineering aspect of converting coal and tar to liquid fuels, principally gasoline; and the equipment for the process. The literature covered includes documents of the United States and British Governments, journals, and other publications. Bureau results in the hydrogenation field are also incorporated.

Jan 1, 1968

By Brian FitzPatrick, Michael J. Weaver

Everyone has a role in site safety, even consultants. This paper presents a summary of how a geotechnical and environmental consulting firm, with field staff on construction and subsurface explorations sites, engaged their staff and leveraged relationships with contractors to assess the construction related risks to which its staff members are exposed. These findings were then integrated into their technical training materials for both new staff and those needing a refresher, so that safety is discussed at the same time as the technical work and not treated as a separate topic. The paper outlines the process of identifying and evaluating the construction related risks that staff members face and presents examples of how the consultant can engage contractors in the process. By doing this, knowledge can be shared and there is a better mutual understanding of the risks associated with common construction and exploration related field tasks. The work resulted in an increase in staff engagement in safety, a better understanding of the true risks that staff face in the field, better relationships with contractors, and lower safety metrics. HISTORY At Haley & Aldrich, Inc., we renewed our safety journey in May 2012. Like many others, we had concerns over injuries our staff experienced in the three previous years, and a potentially significant utility strike we experienced while excavating a trench. In 2009, 2010 and 2011 we experienced an increase in recordable injuries, including two significant injuries, which caused our Experience Modification Rate (EMR) (see note below), Total Recordable Incident Rate (TRIR), and Days Away-Restricted, and Transferred Rate (DART) to rise significantly. See Fig. 1 for details. This caused us to step back and review our approach to safety, and our “safety culture”. The rise in reportable incidents and injuries also corresponded to the beginning of a growth period for the company.

Jan 1, 2019

By Hidenori Hatta, Takero Watanabe, Hideo Yoshida

"The effect of the quenching rate on age hardening in an Al-6.0mass%Zn-0.75mass%Mg alloy sheet was investigated. The quenching rates and aging conditions were as follows: water quenching (WQ) or furnace cooling (FC) followed by pre-aging at 20°C,then artificial aging at 120, 160 or 200°Cwere performed. The peak strength of the FC and the WQ are very similarat120°C aging. It is important high strength was obtained even at the extremely slow quenching rate. On the other hand, the strength of the WQ significantly decreased compared to the FCat200°C aging. GP(I) zones were formed during the pre-aging at 20°C even if the cooling rate was very slow like the FC, and were transformed into the GP(II) ones at 70°C or higher and then into the ?’ phase. However, these zones were dissolved by reversion during heating to 200°C. Thus the strength of the WQ decreased. On the other hand, it is considered that an unknown cluster or GP zone with a thermal stability formed during the FC was not dissolved up to 200°C and was transformed into the ?’ phase. Therefore, a higher strength was obtained in the FC for the200°Caging.INTRODUCTIONAl-Zn-Mg alloys are widely available in commercial production because these alloy have lower quench sensitivity and can be produced by air cooling (AC). Heat treatable aluminum alloys are usually produced by water quenching (WQ) to increase their strength because a high cooling rate inhibits the precipitation of the stable phase during cooling and increases supersaturated solute atoms. However, Baba(1967)reported the strength of an Al-6%Zn-1.8%Mg(mass%) alloy without additional elements quenched by very slow cooling (15°C/min) was 96% of that quenched by WQ. Furthermore,the age hardening at room temperature (RT) occurs after annealing at 410°C followed by furnace cooling (FC, 0.5ºC/min or less)in these alloys. Therefore, the process of annealing at 410 to 430°C for 120 min followed by AC, and reheating at 230°C for 240 min, then cooling is recommended in the specifications (Japan Aluminum Association, 2011). Matsuda and Yoshida(1996)also recommended annealing at 300°C for Al-Zn-Mg alloy extruded products to inhibit age hardening at RT by precipitating the solute atoms and decreasing them in the matrix. It has been considered that the higher the content of excess quenched-in vacancy becomes by WQ, the higher aging rate at RT is obtained. Therefore,it is theoretically and commercially important to clarify the reason why the age hardening occurs relatively quickly in almost no excess quenched-in vacancies such as the FC, and why the same strength as the WQ can be obtained in the FC"

Jan 1, 2018

By Eugene McAuliffe

In the year 1581, the counselors of King Philip of Spain suggested to that monarch that a canal across the Isthmus of Darien would open the west coast of the South American continent to Spanish miners and explorers, enlarging and expanding the flow of precious metals then just beginning to trickle across the path cut by Spanish Conquistadors, from old Panama to Puerto Bello on the east coast. The King sent out a party of surveyors and explorers under the command of a young engineer, Savadaerro, who returned after two years, reporting upon a location for a canal which was virtually adopted by the French engineers employed by De Lesseps, who in 1877 commenced the work of constructing the Panama Canal-296 years after Sava- daerro's first survey was begun. The suggestion for an Isthmian canal, made to the king at a time when Spain was a proud, virile nation and when that country was contending with England in the fields of discovery and conquest, represents a measure of vision that has never failed to intrigue the imagination. That the young Spanish engineer recommended an undertaking so gigantic in conception that it took three and one-third centuries for its completion from the time it was first visioned matters little. In the day of Philip of Spain,

Jan 1, 1932

By H. Demirel

This paper deals with concentration of hematitic-limonitic iron ores. The ore sample obtained from Karakuz (Turkey) contain:. about 40-46 I Fe. First, a low intensity magnetic separation process was employed to separate the strongly magnetic particles cf "-10+2 mm" and "-2+0.075 mm" size fractions and magnetic concentrates with 59.1 % Fe aid % 58.0 Fe were obtained respectively. The non-magnetics of both fractions were then fed to a nigh intensity permanent magnetic separator. The Fe contents of "-10+2 nun" and "2+0.075 mm" size fractions were increased from 28.2 to 51.13 and from 35.4 7. to 43.25 respectively after single pass. Easing on these results, it was concluded that the high intensity permanent magnetic separator could he used as a pre-concentrator f.7.1- hematitic-limonitic Karakuz iron ore.

Jan 1, 1991

By C. W. Davis

This paper is the second of a series of progress reports on a study of the hydrometallurgy of manganese which is being, conducted in an endeavor to make possible utilization-of the large deposits of low-grade domestic manganese ores that occur in several States. There are at least four processes in which a knowledge of the action of S02 gas on manganese oxides at elevated temperatures may prove of value.

Jan 1, 1930

By John D. Ridge

Here are summarized 162 papers, published between 1933 and 1967, that deal with various aspects of ore genesis. Emphasis is placed on additions to, or modifications of, ore-formation theory, no matter what type of deposit is discussed. More space is given to papers on the formation of base-metal sulfides solely because more papers are written on this subject. The final conclusion is reached that a chemically and geologically sound theory for the genesis of ore deposits can be built around the concept of concentration of ore e’ements in a magmatically produced ore fluid and around such surface processes as may act to concentrate economically valuable materials from rocks of any origin exposed at the surface.

Jan 1, 1968

By J. O. Lewis

In its efforts to reduce waste, and increase efficiencyin oil production, the Bureau of Mines is investigating methods of increasing the recovery from the underground sources of supply, which are the foundation of the petroleum industry and the many allied industries wholly or partly dependent on it. In the face of a demand that is increasing faster than the production and that, in the consensus of opinions of well-informed authorities, is soon likely to outstrip the productive capacity, it is well to consider whether it is not possible to extract more oil from the known sources of supply. It is universally acknowledged that by the usual production methods much oil is left underground, the general opinion being that at least 50 per cent of the oil in a field remains unrecovered when the field is abandoned as exhausted. From the writer's own investigations he believes the average recovery is even less, and if any considerable portion of this oil being left underground could he made available it would have a tremendously favorable influence on the petroleum industry and all the industries dependent on it. In this publication are considered the principles involved in increasing recovery and methods of extracting more oil from the oilbearing formations than by the usual ways of producing. These methods are: The use of gas or vacuum pumps, forcing compressed air or gas through the oil-bearing formations, displacing the oil by water, and better utilization of the natural pressures in the oilhearing formations. Especial attention is being given to a processcommonly known as the Smith-Dunn-for forcing compressed air through oil-bearing formations because it is believed to hold most promise for the future.

Jan 1, 1917

By M S. Powell

In this paper it is argued that we are entering a new mining era, based on considerably more challenging orebodies as we rapidly expand minerals production by exploiting previously uneconomic deposits. Rapidly increasing production costs cannot be sustained by continually increasing commodity prices, as illustrated by the recent downturn in the industry.Driven by reduction in grade, requiring the processing of 50 to 100 per cent more ore to recover the same amount of metal, often accompanied by finer grain structure - necessitating a finer product size and more challenging recovery - the productivity of the mining industry is dropping in real terms. The author suggests that tweaking current technologies and relying on economies of scale will not turn the industry around, but rather a switch to considerably more efficient processing is required.It is imperative to utilise the properties of the orebody, especially in terms of variability, in revolutionising our processing techniques. Our new mantra may be æselective mass mining with flexible processingÆ. This paper explores how this may be implemented using current technology and equipment in order to change the cost profile of the new mining industry. Orebody knowledge, based on the underlying process drivers, rather than proxies, is required. These properties and their variability will need to be propagated into the orebody through utilising the geological data rather than smoothing block averages, which destroys information on variability.Novel flexible circuit designs are presented that can respond to a wide variability in ore properties and throughput requirements in order to slash processing costs and energy utilisation, while enhancing overall recovery. The success of these circuits will be based on an ability to predict at both design stage and in everyday processing the variable ore properties, which is dependent upon reliable orebody knowledge that caries variability and underlying processing properties.CITATION:Powell, M S, 2013. Utilising orebody knowledge to improve comminution circuit design and energy utilisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 27-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By R. Dewey

WHAT IS AI? It's very hard to say. Most researchers and practitioners disagree with nearly any attempted definition, but most would agree that A1 does deal with the development of computer-related methods o f problem-solving. Artificial intelligence is a discipline which seeks to emulate human anatomy and/or thought processes by applying computer science, electronics, and mechanical engineering to the development of natural language processing, machine vision, robotics, and knowledge-based expert systems. Integration of these four fields will someday produce the robots of today's science fiction. A1 addresses problems of structuring large amounts of knowledge and representing relationships with rules and semantic frameworks rather than with mathematical equations. A1 is convergent rather than divergent - - conventional conputer applications use relatively small quantities of input to generate large output, but A1 generally reduces large amounts of information to establish a few major conclusions. The development of A1 has prompted greatly increased efforts on the part of scientists and engineers to understand just how humans think, organize information, approach problem-solving, and form conclusions. Some of the more exciting and possibly far-reaching advances in A1 are coming in this more-or-less soft-science area. Thirty years of A1 research (dating from a 1956 conference at Dartmouth College at which the term A1 was coined) has already spawned many widespread, almost ordinary, products: window graphics, hand-held controllers (mouse). function menus, etc., all in an attempt to make computers and people more compatible. WHAT IS AN ES? A1 can be used to develop EXPERT SYSTEMS, which are computer programs or systems which contain knowledge and rules by which problems can be solved. or at least by which possible solutions can be suggested for very complex problems. A1 can be used to better define problems so that solutions can be found. An ES is designed not to process numbers, but to process information according to rules and logic derived from actual practice and experience. WHY AI? WHY ES? Companies are increasingly aware of the value of accumulated knowledge and experience in designing, building, operating, and maintaining the increasingly complex or expensive physical plants in any business. As knowledge branches out and becomes more specialized, the accumulated learning of a veteran operator or manager or engineer becomes a scarce resource well worth preserving. EXPERT SYSTEMS offer a means of doing that, reinforcing, not replacing, human capabilities.

Jan 1, 1987

By R. B. Bauder

In connection with a Bureau of Mines research program on utilization of Cuban lateritic ores, a comprehensive review was made of the chemical literature on nickel and cobalt. Initially, the review had as its objective the selection, from the voluminous literature dealing with the chemistry of these two metals, of only those references to reactions that were especially pertinent, or at least closely related, to the field of extractive metallurgy. Later, the coverage was extended to include references to the techniques and plant applications of extractive metallurgical procedures for the recovery of nickel and cobalt. In this report, the period from January 1929 to July 1955 has been covered, as it seemed logical that recent literature should be of greatest value. This cutoff date was established in order that the bibiliography could be issued at an early date, inasmuch as currently much work is in progress on the lateritic ores. Later, a supplement will be prepared extending the coverage to about 1900.

Jan 1, 1957

By Roger C. Malan

The Monument Valley and White Canyon districts are in northeastern Arizona and southeastern Utah. Exploration and mining for uranium has been conducted in these districts since the late 1940's. In July 1965, ore reserves plus ore production at 174 properties were approximately 3.3 million tons of ore containing about 19 million pounds U3O8, of which about 10 per cent remained in reserves. The two largest mines, Monument No. 2 and Happy Jack, together account for about 45 per cent of the sum of production and reserves. Approximately half the deposits in these districts contain less than 1000 tons of ore. Nearly 5000 feet of Permian, Triassic, and Jurassic sedimentary rocks, mainly continental in origin, are exposed in these districts. All the important uranium deposits are in the Shinarump, the basal member of the Chinle Formation of Triassic age. The Shinarump lies on a widespread unconformity. It is composed of fluvial sediments, generally less than 100 feet thick, that were deposited by streams flowing from a source to the south. Most of the deposits are in an arcuate belt, convex to the west. This belt, 3 to 12 miles wide, extends from Monument Valley northward nearly 130 miles. It is along the western flank of the ancient Monument Valley-Monticello upland, an area that was slightly uplifted at the beginning and again at the end of deposition of the Shinarump. Erosion and subsequent reworking of the Shinarump sediments in the vicinity of this upland are postulated to have made possible the transportation, in solution, of the uranium contained in these sediments. The soluble uranium probably was carried by migrating ground water into sites favorable for precipitation in Shinarump beds bordering the upland. Thus, the original very small amounts of dispersed uranium in the early Shinarump sediments were accreted in the favorable belt where the accumulations of carbonaceous plant remains and their decay products provided a persistent reducing environment.

Jan 1, 1968

By P. N. Anyalebechi

A comparative study of the mechanical properties of automotive steering knuckles produced by three different shape-casting related processes has been conducted. It involved the characterization of the tensile and fatigue properties of aluminum alloy A356 knuckles produced by the vacuum/pressure riserless casting (VRC/PRC), pressure counter pressure casting (PCPC), and the hybrid Cobapress (a casting-forging) processes, in accordance with the appropriate ASTM standards. Surprisingly, the knuckles produced by the hybrid Cobapress process exhibited the lowest strength. For example, the average 0.2% yield strength of the Cobapress knuckles was 31 MPa and 40 MPa less than that of the VRC/PRC and PCPC knuckles, respectively. However, between stresses of 150-200 MPa, the fatigue lives of the VRC/PRC, PCPC, and Cobapress knuckles were comparable. But above 200 MPa, the Cobapress knuckles exhibited the lowest fatigue life. The observed differences in the mechanical properties are attributed to the inherently different microstructures of the different knuckles.

Jan 1, 2009

By H. Z. Kuyumcu

Associated with the development of a novel microbiological oxidation process for the conditioning of iron hydroxide slurries from ferrous mine waters, there is a realistic chance to make the contained iron available for a material utilization. The transformation of ferrous into ferric compounds is coupled with the precipitation of iron hydroxisulphate mostly in terms of the mineral Schwert-mannite. The further treatment of the iron hydroxisulphate has to be aimed on the processing for product recovery and product refinement. For many potential applications, e.g. in the ceramic industry, the pigment industry or for metallurgical applications, the removal of sulphate is essential. For the dehydration of the iron hydroxisulphate and the sulphate removal, microwave heating technology is a beneficial method. In contrast to conventional thermal heating processes the supply of energy in microwave application takes place directly within the material through the dissipation of electromagnetic energy, i.e. no heating medium is needed. It is a volumetric heating process regardless of the surface of the material. The rapid and targeted energy supply and the good controllability of microwave heating systems are advantages which have led to a wide variety of applications in industrial processes. Among the diverse use for heating of temperature-sensitive, chemical and pharmaceutical products as well as foodstuffs the number of applications also in mineral and solid processing increases. At the Department for Mechanical Process Engineering and Solids Processing of the Technical University Berlin the use of microwave technology for the treatment of iron hydroxisulphates has been investigated systematically within the framework of a cooperative research project. The paper at hand shows results from material conversion tests subject to a variation of the relevant process parameters. The reaction products are characterized and the process is compared with the conventional heating in a rotary kiln.

Jan 1, 2014

By Jerry C. Tien

In 2009 China mined 2.695 billion metric tones (Gt) of raw coal. It is estimated that only 3-5% or roughly 135 million metric tones (Mt) of these were mined from 300 some surface operations. Except for a dozen or so large modern operations, most of China's surface coal operations are small by western standards, with annual production ranging from a few thousand tones to 300,000 metric tones (mt). Depending on the size of operations, equipment used range from small trucks and shovels to large bucket wheel excavators and draglines in sizable pits. This article provides a brief overview of China's surface mineable coal reserves, mining methods commonly used and increasing environmental concerns; introductions of several large surface operations are also provided.

Jan 1, 2012