Search Documents

By D. S. Choi

This paper presents a theoretical analysis of the effect of shape and size on strength of geologic materials. The results indicate that the shape effect is caused by the development of confining pressure at the interfaces. The linearization of the obtained formula is of the same form determined by experiments. The size effect is attributed to the fact that the geologic materials contain discontinuities in the form of fractures, bedding planes, and cleats. The maximum reduction factor for the size effect is the one-sixth power of the volume of a cubic test specimen. The results of this work are particularly useful in determining the strength of coal pillars in underground mines.

Jan 1, 1989

By John Kinneen, Sunghoon Choi, Arne Fareth, Edward S. Barboe, Kyle R. Ott

A new water treatment plant is to be constructed for a portion of the water supply system of New York City. The project includes construction of new water conveyance tunnels crossing perpendicular and sub-parallel to the existing pressurized water tunnel at two locations. A study was conducted to evaluate the impact of new tunnel construction on stability of the existing tunnel and hydrojacking potential in the surrounding rock mass. This paper introduces a practical approach to evaluate tunnel interaction, expressed in terms of rock-liner interaction, stress-induced stability and hydrojacking failures. A simple method to evaluate hydraulic and mechanical properties of concrete liners and jointed rock mass is also presented.

Jan 1, 2007

By H. Fayed

Two-phase (water and air) flow in a self aerated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). A 0.8 m3 model is considered. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Because of the lack of circumferential periodicity in this machine, the entire machine is modeled and unsteady simulations are conducted in the whole volume of the bulb. Uniform bubble diameter is specified, and the effects of bubble diameter are determined by conducting simulations for three diameters of 0.5, 0.7, and 1.0 mm. The unsteady air flow rate through the machine is predicted as an outcome of the simulations. Air volume fraction contours and velocity field in different parts of the machine are presented and discussed.

Jan 1, 2012

By R J. Norris, D J. MacKenzie

Gold-bearing veins have formed at a wide range of depths throughout the uplift history of the Otago Schist. The earliest gold mineralisation occurred during the later stages of Mesozoic metamorphism. This mineralisation was characterised by diffuse wall rock alteration with greenschist facies metamorphic or retrograde metamorphic mineral assemblages, and gold occurs in this altered rock. Quartz veins formed in .steeply dipping extensional fractures associated with this mineralisation type strike north to northeast. The Macraes mine exploits this deposit type. The present northwest strike of the mineralised zone at Macraes is a result of post-mineralisation deformation of the schistosity-parallel mineralised shear zone which hosts northeast striking extensional veins. This combination of schistosity-parallel shear zone and steeply dipping northeast striking veins may exist elsewhere in Otago, and this deposit type is most prospective. Steeply dipping quartz veins formed during post-metamorphic un-roofing of the Otago Schist strike northwest to west and occur as clusters of near-parallel structures in east and central Otago. These veins consist mainly of massive quartz, although some prismatic quartz occurs also. Breccia fragments in veins are common and these are generally silicified, with some gold. Wall rock alteration is negligible, and vein margins are sharp. A set of middle Tertiary veins occurs in northwest Otago. Most of these also strike northwest and dip steeply, but some strike northeast. These veins contain abundant ankeritic carbonate as well as quartz. The carbonate pervades adjacent wall rock as veinlets, but gold mineralisation is confined to veins. Quartz is commonly prismatic and vuggy, and contains gold, which is commonly coarse grained especially in silicified breccia zones. Associated veins contain stibnite. This vein type formed close to the paleosurface (>2 km). Mineralised veins in Marlborough currently strike northwest, but these have been rotated from northeast strike during Alpine Fault displacement of Marlborough from Otago. Some of these veins were formed under late metamorphic conditions and are similar to the north to northeast striking veins in Otago. As in Otago, this type should be considered to be most prospective if they have associated schistosity-parallel shears.

Jan 1, 2000

The Determination of Sound Exposures (DOSES) software was developed by the National Institute for Occupational Safety and Health (NIOSH) specifically for use by mine management and safety personnel. DOSES simplifies the record-keeping and analysis associated with time-motion studies and worker noise exposures, making it easier to identify and solve noise problems. The software relies on a time-motion study that profiles the worker?s daily activities. At the same time, noise measurements are collected with a dosimeter or sound level meter (SLM). Observations about the worker?s location and tasks or other activities are recorded along with times and durations so they can later be matched up with the noise data. After the completion of a time-motion study of the worker?s daily tasks and locations (possible noise sources), which measures the worker?s noise exposures during the recorded events, the information is entered into DOSES. The program then displays information about the worker?s accumulated noise dose over time.

Jan 1, 2009

By A. Desbiens, A. Pomerleau

During the summer of 1994, a new PID-based control strategy was installed on line B of the grinding circuit at the Kidd Creek Division of Falconbridge Ltd. Part I of this paper described the methodology used to select the appropriate control strategy using a phenomenological dynamic simulator. Part II presents the implementation of the control strategy. Prior to the controller installation, it was necessary to solve various problems related to the process, such as a cyclic behaviour of the rod mill feed tonnage, a problem related to the mill water source and the calibration of the flowmeters. Once these problems were solved, the control strategy was accomplished in two steps. Step 1 corresponds to the installation of control loops to regulate the pump box level and the cyclone overflow density. Step 2 describes the implementation of a loop to control the cyclone feed density. According to Part I, a loop to control the circulating load is also part of the original design. However, reasons are given to explain the rejection of this loop. For both steps, technical procedures such as filtering, process identification and controller tuning are detailed. Finally, the operator’s interface is briefly described.

Jan 1, 1997

By S Mundell, J Armstrong, M Evans

"Automation is a common goal within the coal industry for reasons such as efficiency, reliability and sustainability. However, it requires standards and frameworks so business systems can communicate effectively. Automation of sample analysis processes has been difficult to establish due to a lack of direct business system communication between commercial laboratories and mining companies. This has resulted in manual procedures that have contributed to problems relating to analysis instructions, sample identification, results formats and visibility of status.These problems result in loss of data and confidence in data validity, loss of process efficiency and inability to react to issues. An Australian Coal Association Research Program project (Evans, Armstrong and Arboleda, 2014) has addressed these issues through the Coal Quality Data Exchange methodology for direct business system communication between coalminers and commercial laboratories to optimise the transfer of coal quality data.The benefits to the coalminer of the framework are:increased clarity and auditability of what is being sent to the laboratory and what was requestedreduced potential for error introduced through manual transcription tasksincreased speed of loading of analytical results to the customer Geoscientific Information Management Systemimproved turnaround time for analytical resultsincreased knowledge about what took place in the laboratory with respect to the determination of the analytical resultsincreased visibility of the status of a ‘work order’. The benefits to the technology companies and commercial laboratories is a common framework on which to build a sustainable solution that gets away from the multitude of formats catered for today and time consuming manual processes. The common framework significantly advances the future possibilities for the automation of sampling and analysis processes in a production environment.CITATION:Armstrong, J, Mundell, S and Evans, M, 2014. Automating communications between laboratories and mines – a case from the coal industry, in Proceedings Ninth International Mining Geology Conference 2014 , pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By C. Perea, O. Restrepo, C. Ihle, H. Estay

In this study, research on the use of monosodium glutamate for copper leaching, with emphasis on the thermodynamics and oxidant characteristics, is presented. Copper dissolution was conducted following a hydrometallurgical route, using monosodium glutamate in alkaline solutions. The effect of oxidizing agents such as hydrogen peroxide (H2O2) and potassium permanganate (KMnO4), and the efficiency of copper leaching with glutamate compared with glycine have been studied. Results, obtained at room temperature, showed 92% recovery of copper using 0.03 M hydrogen peroxide, 0.5 M monosodium glutamate at a pH of 9.44.

Mar 2, 2022

By Howard A. Perko, M. Mae Benvenga, Heather H. Trantham

Displacement of soil and groundwater during helical pile installation can produce excess pore water pressures (PWP) in fine-grained soils. Pore water pressure reduces effective stress in the soil immediately adjacent to the helical pile shaft and near the helical piles. Previous studies have shown generation of PWP may affect the capacity to torque ratios of the helical bearing elements. Large diameter helical piles that generate much of their torque and capacity from shaft adhesion are affected by PWP and therefore exhibit significant pile "freeze" after installation. Computer modeling is used herein to evaluate PWP immediately adjacent to helical pile shafts during installation in various soil types. The models show the degree and distance from the shaft that is influenced by PWP during installation and the amount of time required for the PWP to dissipate. Pile freeze has been measured on several project sites by re‐torque measurements. These re-torque data are compared with computer modeling and correlations between saturated hydraulic conductivity and dissipation time are presented and discussed. INTRODUCTION Helical piles are full-displacement piles, meaning installation does not produce drill spoil. Soil is displaced laterally as the pile progresses into the ground. This displacement of soil causes an increase in PWP, which reduces adhesion between the pile and the soil. For helical piles with small-diameter shafts, adhesion contributes little to the overall capacity and torque of the pile, so PWP changes are not typically considered in determining pile capacity. In modern construction, the use of larger diameter helical piles has become very common. For large-diameter helical piles, changes in PWP immediately adjacent the shaft can be quite large during installation. Increased pore water pressure and reduced adhesion can have a temporary effect on pile capacity and installation torque.

Jan 1, 2018

By H. Tomlinson

"INTR0DUCTIONThis publication is a third of a series devoted to falls of roof and coal in coal mines of the Western States. It gives the results of examinations of the mines of the Rock Springs coal District of Sweetwater County, Wyo., which represent the principal coal beds therein and approximately 75 percent of total production of the State.A study was made of safety conditions at all the producing mines of the district and suggestions were offered the operators regarding methods and practices which would, in the opinion of the writer, provide additional safeguards to prevent accidents from falls of roof and coal.In presenting the subject, consideration must be given to such features as character of the coal beds, depth of cover. methods of mining, timbering practice, roof testing and supervision, and for comparative purposes to certain statistical matter bearing upon relation of accidents to their causes, tonnage produced, men employed, days worked, and lost days due to accidents during the 3—year period covered by this study.ACKNOWLEDGMENTSThe writer acknowledges the cooperation of the officials of the various coal companies, without whose assistance this work could not have been completed.F0UR REPRESENTATIVE COAL OPERATIONSThis report relates to four representative coal operations in the Rook Springs district of Sweetwater County, Wyo., which are referred to as mines A, B, C, and D. This group employs yearly an average of 993 men, representing 37 percent of the men in coal mines of the county, and has an average annual production of 1,484,373 tons, representing approximately 44 percent of the coal produced in the county. Figure 1 is a map of the Rook Springs coal district."

May 1, 1933

By Lonie W. M

The rapid development of the Australian steel industry over the past twenty years has greatly increased the demand for coking coal from the collieries owned by the Broken Hill Proprietary Co. Ltd. and Australian Iron & Steel Ltd. This in turn has called for an intensive and continuous programme of colliery expansion and new colliery development, along with the reorganization and modernization of existing collieries.This paper presents a general description of the factors involved and the techniques used in planning modern colliery development for the steel industry.PRELIMINARY GEOLOGICAL INVESTIGATIONSIn any colliery development, preliminary geological investigations require a detailed and practical knowledge of the geology and characteristics of the coal-field as a whole. In the early stages of the investigations, probably the most valuable information is obtained from outside the particular area under review, rather than within it, and unless the geology of the coal-field is understood, the projection of the known information into the unknown area cannot be carried out with certainty.Because development of the coal seams from the outcrops has been an apparently simple matter and not subject to the risks involved in deep mine development, the geology of the New South Wales. coal-fields has not received the attention that major mineral resources warrant.Only the most accessible regions of the coal measures have been generally prospected, while the potential areas remain...

Jan 1, 1957

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, produced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. 1). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OF THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By Bowen Li

Andalusite is an excellent raw material for refractory applications due to its high aluminum oxide content and phase transformation to mullite at high temperature. Granular andalusite in particle sizes of about 1 to 2 mm was traditionally utilized for the manufacturing of refractory brick. However, if powder andalusite in micron particle size is utilized in high-alumina refractory products, reinforcement on the refractory brick can be obtained and the sintering temperature can be decreased. The phase transformation of powder andalusite plays a key role for the difference.

Jan 1, 2006

Studies of the Main Seam in the Rapahoe Sector of Greymouth Coalfield have shown that the proportions of palynomorphs and palynomorph groups vary vertically within the seam, but remain laterally consistent. Subsequent examinations of other seams in the Rapahoe Sector have demonstrated that the changes in palynomorph proportions observed in the Main Seam are specific to that seam, effectively providing a seam 'fingerprint'. Such a characteristic signature may be used to identify the Main Seam where faulting or seam splitting confuses seam correlation between drillhole intersections. Palynomorph assemblages are derived from the original plants which formed the peat mire, and yield information on mire conditions such as climate, mineral matter input and chemistry. These depositional factors influence coal properties such as mineral content, volatile matter yields and coal breakability. Palynological data can therefore assist in development of depositional lTIodels for prediction of coal quality variations. Several other, thiner seams in the Rapahoe Sector have been demonstrated to also contain recognisable palynomorph assemblages, suggesting that other seams may also possess distinct palynomorph abundance profiles.

Jan 1, 1996

The Stawell Goldfield, the westernmost of the main Victorian fields, has produced over a million and a quarter ounces of gold from one and three-quarter million tons of ore. The lodes are quartz reefs and sulphide bodies occurring in sediments of lower Ordovician or upper Cambrian age. The lodes are confined to a relatively narrow suite of weak rocks lying between stronger ones above and below and there is a definite relationship between fold structure, pitch and strength of folding and ore.LOCATION HISTORY AND PAST PRODUCTIONThe town of Stawell, situated 150 miles north-westerly from Melbourne on the main railway and road to Adelaide, is the most westerly of the main gold areas of Victoria. Alluvial gold was found at Pleasant Creek (now Stawell West) in 1853 and the usual "rush" followed. Numerous alluvial leads, some surface, others buried under up to 100 ft. of Tertiary sediments were worked. The alluvial gold was soon exhausted, but in 1857 gold-bearing reefs were found on the slopes of a prominent ridge on the northern edgeof the present town. Early reef mining was by small working parties mining to shallow depths only and treating their ore at public crushing plants. Some of the early returns were very high grade. The next stage was the amalgamation of claims and the formation of companies, with their own treatment plants. This stage continued till the last mine closed in 1921. These companies had, by present standards, small holdings and far too many shafts were sunk, resulting in less efficient prospecting and operation.Since 1921 there have been one or two small scale attempts to revive mining but without success. Of recent years Gold...

Jan 1, 1960

In gold ores, the range of value disclosed by ordinary mine sampling is very wide, and the number of 'samples required for a reliable average is correspondingly great. Even where a large number of samples is available the weighted mean value of the samplesalmost invariably exceeds the true gold content. In operating mines this disparity is overcome by arbitrary reduction of high assays until reconciliation is achieved, but it is frequently necessary, especIallyin exploration, to base an estimate or to reach a decision on a relatively small number of samples from underground openings or even on a few drill hole intersections. In these circumstances, a decisive influence may be exercised by the weight allowed to high assays and to low grade intersections, both of which events are, of course, dependent on the metal distribution in the ore. Where sufficient data are available, statistical analysis will measure the risk involved, but as this information is seldom to be had, the final choice becomes largely a matter of personal judgment.With this problem in mind, a study was made some years ago of the distribution of values in four Western Australian gold ores, with the primary purpose of learning from actual ore-bodies of differing types, something of the metal distribution in the smallquantities of ore involved in individual routine mine samples, and of the importance in each case of high assays. Adequate and suitable data were available in .four cases, in three of which high assays were of frequent occurrence due to the presence of free gold. The results give concrete expression to well known differences of metal distribution, and it is proposed, firstly to record the observed distribution; secondly to examine some of the consequences of the differences in the distributions limd thirdly, to comment, in the light of this data, on the vexed question of the treatment of high assays. Standard statistical procedure was employed in the compilation of the data. The assays were classified by value into groups, each group covering a range of value of 1 dwt. per ton. Assays of less than 1.0 dwt. per ton form the first group; assays equal to or greater than 1.0 dwt. and less than 2.0 dwt. comprise the second group; those equal to or greater than 2.0 dwt. and less than 3.0 dwt. appear in the third group; and so on. Where the number of samples is large, it can be assumed that the mid-value of the group is the mean value of all the samples in the group, thus the mean values of the first three groups are 0.5 dwt., 1.5 dwt. and 2.5 dwt. respectively.The number of samples in the group is the frequency of the group, but for convenience of plotting this frequency is converted into percentage of all the samples in the series. Plotting percentage frequency as ordinate against dwt./ton as abscissa results in a frequency curve-a curve showing the frequency...

Jan 1, 1950

Several Approaches to Enhance the Bioleaching of Enargite Some approaches were investigated to enhance the recovery of Cu from enargite by bioleaching with Acidithiobacillus ferrooxidans using the galvanic interaction with pyrite and activated carbon, and with thermophilic bacteria, Acidianus brierleyi. Addition of pyrite initially enhanced Cu leaching by the Galvanic effect, but after that the formation of secondary minerals passivated the surface of enargite in inoculated batches. Activated carbon improved Cu recovery from enargite much better than pyrite, when it is contacted with enargite. Recovery of Cu from enargite has been recorded to at largest 2.4 per cent within 30 days in the presence of activated carbon when mesophilic bacteria were inoculated at 25¦C. The recovery of Cu from enargite was drastically enhanced by inoculation of thermophilic bacteria, Acidianus brierleyi, up to 60 per cent within 40 days at 70¦C and still not leveled off after 40 days unless the formation of Fe(III) precipitates occurred. After 40 days dissolved molar ratio of Cu/As is around 5.2, suggesting that metal-deficient sulfides and/or ferric arsenate might be formed on the surface of enargite.

Sep 13, 2010

By A. C. JR. Boyle

I. INTRODUCTION THE geological field work of the Bully Hill district, upon which this paper is based, was begun July 1, 1908, and covered a period of three months. The time was found too short for a complete report and the district was again visited in the early part of July, 1912,. from which time detailed study of the locality continued until September of the same year. This paper is the result of observations made in the mines in the immediate vicinity of Winthrop, Shasta county, Cal., during these two periods of study. The preparation of this report has been greatly facilitated by various courtesies rendered the writer by D. M. Riordan, President of the Bully Hill Copper Mining & Smelting Co., and by John B. Keating and Herbert R. Hanley, managing officers actively in charge at the mines. The elaboration and further study of the notes and collections were carried on in the laboratories of the Departments of Geology and Mining at Columbia University, and the writer takes pleasure also at this point in expressing his acknowledgments to Profs. James F. Kemp, A. W. Grabau, Charles P. Berkey, and William Campbell, for advice and assistance. In order that one may appreciate at first reading the significance of some of the details which follow, and for the sake of clearness, a brief outline of the geological relationships is here given, together with certain conclusions which have been reached regarding the genesis. of the ores and the gypsum masses. In the Bully Hill mining district an associated series of Triassic lavas and tuffs, chiefly andesites, is preceded as well as followed by sediments. The entire system is tilted so that the original bedding planes dip in general to the southeast. The surrounding region has been greatly disturbed, and in the immediate vicinity of the mines close folding of the later sediments and extreme shearing of the igneous rocks locally is a striking feature. Into the nearly vertical shear zones have been intruded post-Triassic dikes of various rock types in the following order: alaskite-porphyry and andesite-porphyry. Outside the area under consideration diorite dikes are known, but they will not receive attention further than to note that' they, probably, represent a differentiation product of the same magma from which the other two dikes came. In this connection all the dikes have an important bearing on the origin of the ores and of the gypsum found in the mines.

Jan 1, 1914

By Kelsall D. F, Trahar W. J

The size by size batch flotation behaviour of copper activated sphalerite from synthetic mixtures with quartz was determined. In terms of recovery of sphalerite, the size fractions could be grouped into coarse, intermediate, and fine ranges. The behaviour of the coarse and fine ranges was significantly poorer than that of the intermediate range in both the extent and rate of flotation.Each size fraction had a fast and a slow floating component.The main effect of changing the copper sulphate addition was to alter the proportion of any size fraction which was fast floating. No correlation could be found, between the amount of copper on the spha:lerite andeither the flotation rate of the mineral or the amount of copper added to the system. It was found that fine particles did not appear to consume greatly disproportionate amounts of copper sulphate during conditioning. A modified conditioning procedure was found to lead to a higher rate of flotation and recovery of coarse sphalerite and to make poss1ble substantial savings of copper sulphate.

Jan 1, 1975

By Thomas L. Craig

The Wellman-Lord SO2 Recovery Process is operating commercially at one location in this country and at two locations in Japan. Tail gases from a sulfuric acid plant, from an oil fired steam generator and from a sulfur recovery unit are the respective applications. 1) At the Olin Corporation's Paulsboro, New Jersey, stack gas from a spent acid regenerative sulfuric acid plant-45000 SCFM - is treated in the W-L unit to reduce sulfur dioxide concentrations from 4500 ppm to less than 500 ppm. 2) At the Japan Synthetic Rubber plant in Chiba Prefecture, stack gas from an oil-fired steam generating plant - 120,000 SUM - is reduced from 2100 ppm S02 to less than 200 ppm. 3) At the Toa Nenryo Kogyo refinery in Kanagawa Prefecture, tail gas from a sulfur recovery (Claus) unit - 41,000 SUM - with, an inlet SO2 concentration of up to 13000 ppm is reduced to less than 200 ppm. The three installations are operating successfully and are capable of reducing S02 emissions to levels significantly below the concentration guaranteed. With the one exception of a higher than guaranteed chemical make up requirement at Paulsboro, utility and chemical requirements will be less than design.

Jan 1, 1971