Search Documents

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r' panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987

By C. Musingwini, G. Njowa, M. Burnett, C. C. Birch

From 2022 to 2040, the global demand for mineral commodities is projected to increase by fourfold to six-fold, largely due to traditional drivers such as population growth and urbanisation compounded by the adoption of decarbonisation technologies that are more mineral intensive than fossil fuel technologies. To meet this projected demand, companies operating in the minerals industry should accelerate the development of mineral projects. Since most of the companies generally operate in multiple geographical, regulatory or legislative jurisdictions, it is critical that the information on Mineral Resources and Mineral Reserves they report on in the public domain should be comparable and consistent across different jurisdictions. The Committee for Mineral Reserves International Reporting Standards fosters alignment of national and regional mineral reporting codes through an internationally accepted template that creates common technical understanding of definitions, classification, estimation processes and the Public Reporting of Exploration Results, Mineral Resources, and Mineral Reserves. The Committee for Mineral Reserves International Reporting Standards Template-based codes guide reporting at respective national and regional levels. Since mine planning is critical in the conversion of mineral resources to mineral reserves, a shared technical understanding should aid comparability of mine planning results. However, differences persist in the way mine planning results are reported. Unlike most previous studies, which have primarily focused on comparing mineral reporting codes, this paper updates and extends such comparisons by exploring how similarities or differences in reporting should influence the mine planning process. It also recommends some principle and process changes to assist mine planning professionals to improve consistency and comparability in reporting mine planning results.

Mar 30, 2026

This field guide is designed for use in planning pollution control and reclamation activities on small sand and gravel operations. Its purpose is to assist operators in selecting environmentally desirable pollution control and reclamation procedures based upon their particular mining situation. The guide includes information on interpreting physical and cultural factors that must be considered in planning and implementing a mining and reclamation program, achieving environmental protection objectives, and improving community/industry cooperation. Included as appendices are a summary of state laws and a list of additional readings on the subject.

Jan 1, 1981

By Norman L. Wimmler

Active placer mining in Alaska began near Juneau in 1880, but the first gold rush did not start until 1896; then the discovery of the Klondike brought gold seekers from all parts of the world. A few of the newcomers were experienced miners, but the majority knew nothing whatever of placer mining. Even those who were placer miners of much experience found entirely new conditions, notably frozen ground, that presented many difficult problems. As a result, numerous methods of mining and of thawing frozen ground were tried. From these trials the practice described in this bulletin has been developed. All known placer fields in Alaska have been mined to some extent, and some have been virtually exhausted. In most districts, however, there remain large quantities of low-grade gravel and also some small isolated areas of comparatively rich gravels which could not be successfully mined because of adverse physical conditions. These districts are now the scene of most placer mining, including dredging, hydraulicking, drifting, mechanical methods of open-cut mining, and ground sluicing (or booming) followed by " shoveling-in."

Jan 1, 1927

By J. Yianatos

The collection zone residence time distribution (RTD) of mechanical self-aerated flotation cells was characterized for liquid and solid per size class (-45 mm, +45-150 mm and +150 mm). It was found that a single large industrial cell with a volume of 130 to 250 m3, now used in plant operations, can be well represented by an LTST (large and small tank-in-series) model plus dead time. From a scale-up point of view, results showed a similar mixing behavior for industrial cells ranging from 130 to 250 m3. Also, single mechanical cells showed a similar mixing pattern (RTD) when compared to large pneumatic flotation columns. It was confirmed that for practical purposes, the mixing condition in a flotation bank of three or more cells in series can be well described by the classical N tanks-in-series model.

Jan 1, 2008

By H. Tveit, E. H. Myrhaug, J. K. Tuset

Silicon metal as a commodity material is produced by carbothermic reduction of quartz in electric submerged arc furnaces, where CO2 forms as a by-product. Since 1997 the Norwegian Ferroalloy Producers Association have been engaged in research programmes aiming for reduced CO2-emissions associated with fossil carbon in their processes. One important issue has been to study how charcoal and wood chips perform compared to coal and coke in the silicon process. The ability of the carbon-rich reduction materials to react with SiO-gas is commonly assumed to be of large importance to the performance of the process. Based on laboratory experiments with different carbon materials, combined with estimation of parameters in a mathematical model of the reaction between carbon and SiO-gas, a foundation for a theoretical study of the performance of the carbon materials in a silicon furnace is established.

Jan 1, 2004

By N. Dixon

This report summarizes all work performed under U.S. Bureau of Mines Contract J0377014, "Development and Evaluation of Noise Control Techniques for Taconite Processing Equipment." Three areas of taconite processing equipment, grinding mills, fine screens, and crusher screens have been investigated. Extensive noise and vibration measurements have been made on grinding mills in which the process parameters that affect mill noise have been identified, and the level of shell impact noise around the mill defined. A multiplexing telemetry system was used to obtain shell vibration measurements from a rotating mill. Mill noise control methods were investigated and a partial mill barrier was built and tested on a semi-autogeneous mill. A noise reduction of approximately 3 to 6 dBA was achieved on the falling side of the mill. The use of rubber mill liners on autogenous mills has been evaluated. The noise sources on fine screens have been quantified, and noise control treatments developed. Noise reductions of 11 to 13 dBA were achieved at positions around the fine screen and some in-service testing has been done. Noise measurents of crusher screens were obtained and noise control through resilient screen decks appears to hold the most promise. Additional benefits might be lower life-cycle cost, since the service life of resilient decks is claimed to be longer than steel.

Jan 1, 1983

By Ananda Moreira Vaz Ourique de Avila

High and intermediate temperature fuel cells (FC) are power generators characterized by high efficiency and their use in cogeneration systems. The single fuel cells are connected in series by the use of interconnects to form a fuel cell stack. Ferritic stainless steels have been used in the making of high and intermediate temperature operation solid oxide fuel cells interconnects. However, at high temperatures, on the order of 700-8500C, these steels can present significant oxidation and degradation processes, promoting increased electrical resistivity and corrosion losses that result in contamination of the electrodes and reducing the performance and the useful life of the FC. Intensive R&D activities have been made to minimize these problems and the use of composite coatings on metallic substrate has been considered. This paper evaluates the use of coatings of copper and nickel, with particles of La2O3, Y2O3, CeO2, LaCrO3 and doped chromites applied on ferritic stainless steels AISI 430, AISI 441 and Crofer22APU produced by electrodeposition. The produced samples were evaluated by microscopy techniques, gravimetric analysis and by electrothermal characterization. The most significant results were obtained with chromites coatings (LaCrO3 pure, mono- and multiple-doped) showing the combination of the best features of metal coatings, substrates and ceramic particles with semiconductor properties.

Aug 7, 2018

By G. W. Adams

Foreword While the literature on radium is voluminous, there is no single publication available from Canadian sources which attempts to cover at all fully the world radium industry. The comparatively recent developments in the Wilberforce area, and the consequent arousal of public interest in radium, seemed to call for the publication of such a paper which would be intelligible to the layman. To satisfy this apparent need, the writers submit this paper which contains material derived from various sources, and for which the writers make no claim of originality. Direct references are made throughout the paper to sources of information.

Jan 1, 1931

By Sri Sawmliana, P. Pal Roy

Blasting Gallery (BG) method was introduced in India for higher production and low cost of excavation to substitute conventional hand section and stowing methods for thick coal seam. The Singareni Collieries Company Ltd. (SCCL) adopted this method in the year 1989 and since then successfully operating at GDK-10, GDK-8 & VK-7 Incline mines in Andra Pradesh, a southern state of India. It is also successful at Chora 10 Pit Colliery of Eastern Coalfields Ltd. (ECL) in West Bengal whereas at East Katras Colliery of Bharat Coking Coal Ltd. (BCCL) in Jharkhand State, the method has been partially successful due to some geological constraints of the area.

Jan 1, 2003

By AIME AIME

WITH the example of the steel open-hearth men and their round table conference before the copper men, the query naturally arose "Why cannot we do likewise?" The advantage of pooling and comparing knowledge on smelting in the copper reverberatory furnace seems particularly pertinent at this time when all metallurgical economies possible must be rigorously enforced. A great deal of data had also been obtained and filed during the period of litigation over the Carson patent, and it would naturally be available with the cessation of further suits. With these ideas in mind, H. Foster Bain took up the advisability of holding such a conference directly with the heads of all the companies in the United States operating copper reverberatories, and found a nearly unanimous response. The mining companies appointed representatives directly, or indicated to the heads of various metallurgical operations what members of their staffs should be sent to such a conference.

Jan 1, 1930

By John A. Baker

S EVERAL FACTORS have brought about a vastly greater interest in the gold-mining industry in the last two or three years. Outstanding is the fact that there is an open market at a fixed price for all that can be produced. a condition that holds for no other commodity. Costs of production have decreased greatly, owing to lower prices of supplies and equipment and lower wages. Improved metallurgical processes and equipment are also available. To big new gold district is being opened up but virgin ground is being prospected with some success in many of the more remote parts of the world and right here in the United States many old properties are being reopened 111 the light of present condition<, tailing dumps are being re- worked, and profitable leases taken on abandoned property. Many of the men who are becoming interested in gold are mining engineers whose experience has all been with base metals heretofore: some are engineers with no mining experience; some are not engineers at all but men who cannot find profitable employment in their usual field of activity and are attracted by the age-old lore of the yellow metal. Some are business men with a little money and an idea that under present conditions gold mining offers a safer investment for it than most other kinds of business. It is to those more or less inexperienced new- comers in the gold-mining industry that this article i4 ad dressed. Those who are connected with the large gold mines or who have had rears of experience with the small ones will find in the following pages little or nothing of interest but it is hoped that the newer generation of small mine operators, on whom the healthy growth of the industry depends so much, may find here some helpful hints.

Jan 1, 1932

By R. Y. Williams

The investigative work described in this report was undertaken by the Bureau of Mines under a cooperative agreement with the department of mining engineering of the University of Illinois and the Illinois State Geological Survey." The purpose of this agreement was to provide for a comprehensive investigation of coal-mining conditions in the State, with especial reference to the possibility of lessening waste in the mining and preparation of coal and of reducing the dangers to which miners are exposed. The Bureau of Mines paid particular attention to those phases of the investigation that were of general interest from their bearing on safety and efficiency in the coal-mining industry as a whole. Thus, it studied the occurrence of gas (methane) in the mines of the southern part of the State," tested the inflammability of the coal dust from many mines, examined the efficiency of the control of ventilating currents, and investigated the factors affecting the humidity of mine air with respect to their bearing on the occurrence of mine explosions. Following the establishment of the fact that under certain conditions dry bituminous coal dust is inflammable, there arose the problem of finding efficient methods of preventing or limiting coal-dust explosions. Experiments in the gas-and-dust gallery at the Pittsburgh testing station of the Bureau of Mines verified the fact that certain dusts that explode violently when dry are rendered inert by proper humidi- .fication of the atmosphere within the gallery, and the importance of humidity as a factor in limiting the inflammability of coal dust in a mine is demonstrated by the fact that there has never been in Illinois a dust explosion during the summer months, whereas the records show a number of dust explosions during cold weather. It is easy to see that the warm moisture-laden air that enters a mine in the summer must deposit moisture on cooling, whereas the cold and relatively dry air that enters in winter must take up moisture as it becomes heated in traveling through the mine.

Jan 1, 1914

By J. M. Goris

The U.S. Bureau of Mines is conducting research on cable bolt ground supports to assess their material and support properties, to provide design criteria for using cable bolt supports as roof control systems under various types of underground mining conditions, and to provide a mathematical model of cable bolt support systems. Part 1 describes laboratory studies of the support properties of cable bolts made of conventional steel cables and provides recommendations on such topics as the use of thick grouts, selection of breather tubes, and reduction of water bleeding in cement-based grouts. The studies evaluated both single and double cables; effects of different embedment lengths, water-cement ratios, and grout curing temperatures on support strength; effects of use or nonuse of breather tubes; pumpability and water-bleeding properties of grouts; and the strength properties of sand-cement grouts. Part 2 will cover the strength characteristics of birdcage cable bolt supports, epoxy-coated cables, and cables with steel buttons attached.

Jan 1, 1990

By Pablo Velasco

The Belize economy recorded modest growth during 1980; the growth of the gross domestic product (GDP) in real terms was between 1% and 2%. At current prices, the 1980 GDP reached $108 million2. This output was largely attributed to the performance of a few industries, mostly nonminerals. Such performance improved significantly the balance of payments situation by reducing the deficit from $19 million in 1979 to $4 million in 1980. The rate of inflation was an estimated 18% in 1980 and would have been greater if not for a conservative monetary policy and price control on a number of essential items. Expert earnings increased $43 million, or 50%, from the 1979 level. After increasing more than 25% in 1979, imports increased only 6% in 1980 to a level of $141 million owing to the decline in investment and stabilization of petroleum prices. The balance of trade deficit was $9.8 million in 1980, a marked improvement from the 1979 level of $45.1 million. The mineral output for Belize accounted for only a fraction of 1% of the GDP. Such activity was limited to the production of limestone, marl, and sand and gravel, all of which were primarily used in construction of the Northern Highway between Orangewalk and Belize City. Mineral resources are deficient or nonexistent in Belize for the majority of metals and nonmetals, although the Government and others continue to believe that petroleum must exist in Belize. The proximity to Mexican oilfields and the growing finds in the Peters area of Guatemala support this expectation. The Government continues encouraging exploration onshore and offshore and offers terms that

Jan 1, 1982

By T. Holmes, S. Davison

"A surge bin at Agrium’s Vanscoy potash operations has been plagued with flow, wear, and corrosion issues since being built in 1967. The culprits? The bin’s carbon-steel construction, geometry, and the resultant funnel-flow pattern are the root causes. An investigation and cost analysis indicated that hopper redesign and retrofit would increase production and reduce maintenance and capital costs. The retrofitted bin provides safer, more reliable operation and has a much longer predicted working life. Using this example, the authors describe bulk-solids-flow theory and highlight the importance of customizing bulk-material-handling-system design using appropriate flow properties to improve reliability, safety, and cost effectiveness.RÉSUMÉ Depuis sa construction en 1967, un réservoir intermédiaire de l’exploitation de potasse Vanscoy d’Agrium connaît des problèmes de débit, d’usure et de corrosion. Les responsables ? La construction en acier ordinaire du réservoir, sa géométrie et la structure de débit en résultant au niveau de la carotte en sont les causes fondamentales. Une étude et une analyse des coûts indiquaient que la restructuration et la rénovation de la trémie permettraient d’augmenter la production et de réduire les coûts d’entretien et en capital. Un réservoir rénové permet de renforcer la sécurité ainsi que la fiabilité de l’exploitation, et sa durée d’activité prévue en est augmentée. En se fondant sur cet exemple, les auteurs de l’article décrivent la théorie du débit de matières solides en vrac et insistent sur l’importance de personnaliser la conception du système de manutention des matériaux en vrac à l’aide de propriétés rhéologiques adaptées afin d’améliorer la fiabilité, la sûreté et la rentabilité.INTRODUCTIONIn early 2013, Agrium’s Vanscoy Potash Operations (VPO) engaged Jenike & Johanson Ltd. (J&J) to provide testing, consulting, and structural engineering services related to proposed modifications to the 270 t special standard product surge bin, which Agrium planned to undertake during a two-week shutdown in August 2013. The bin, which had been plagued with flow, wear, and corrosion issues for its entire working life, was essential for the continuous operation of two of VPO’s compaction plants and for efficient dispatching to loadout. The bin often experienced product hang-ups, clumping on the walls, and plugging at the hopper outlet. Two recent unscheduled mill shutdowns had been partially attributed to flow issues in the bin due to clumping and product plugging up at the screws. These problems increased maintenance costs, limited production capacity, and degraded product quality. Holes and paper-thin sections in the bin walls discovered during a 2013 inspection revealed the potential for major hot material leaks or even structural failure. Either issue would stop plant operations until the bin could be repaired or bypassed. Clearly, the bin cone had reached the end of its life and required replacement."

Jan 1, 2018

By J. R. Goode

Up to one half of neodymium and praseodymium production, key ingredients in permanent magnets, is produced illegally. About 60% of cobalt production, critical in lithium-ion batteries and other applications, comes from central African states, and much of it is produced illegally. Tantalum, important in modern electronics, is also primarily sourced from central Africa and, again, much of it illegally. Illegal mineral production, as exemplified here, is often used to fund armed conflict. Furthermore, it is typically conducted with scant regard for human rights and environmental protection. It also leads to depressed prices which in turn limits the possibility of legitimate producers entering the market. Systems of traceability and provenance, along with cooperative supply chain participants can limit the production of illegitimate material and thereby improve conditions in the countries of origin and reduce downward pressure on prices.

By P Thwaites

The mining industry uses many types of mineral and metallurgical plants to produce saleable product from ore mined. Plant design history has left current operations with a mixture of manual operation and various forms of automated process controls. Consequently, we typically see high-variability in the continuous operations together with a shortfall in the attainment of full capacity or higher utilisation of consumables.At a level of best practice, ‘operational performance excellence’ focuses on process control, using automation and control systems to deliver process optimisation. This more sophisticated delivery is a great deal more difficult than the first stage of equipment selection/installation. It includes the appropriate selection of the right instrumentation and control system, key process knowledge, individuals with a solid control engineering background/experience and the essential backing/support of the operations management team together leading to higher-value delivery. Robust solutions can be realised, considerably minimising process variation, thus leading to process optimisation. This approach results in an easier, efficient and safer process while providing considerable returns for the plant owners.How variable are your processes, and do you maintain optimised process performance with dedicated resources, modern instrumentation, ‘best practice’ control systems and performance monitoring tools? In this paper, these questions and their possible answers are discussed.I say we can do much more and be ‘more efficient’ in our efforts to remain competitive. This area remains a major opportunity for improved efficiency, minimising tailings losses and other milling costs.CITATION:Thwaites, P, 2014. Manual control, process automation or operational performance excellence – what is the difference?, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 13–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By J. Bongarra

This report describes the development of the instructional design and content of a training program for shaft construction miners and supervisors. The recommended training approach is based on the results of a needs, task, and competency analysis of the jobs performed by conventional shaft sinking and raise drill personnel. Learning objectives were derived from the task analysis and the appropriate training delivery system was chosen using a selection technique which employed learning algorithms. The training described is aimed at improving the safety and efficiency of constructing shafts by new hire and experienced miners and supervisors. A self-paced, self-teaching, modular approach to training, using criterion-referenced tests was proposed. Recommendation was made to divide the training into three parts: Orientation and Safety; Task Instruction; and Practical Exercise. Training requirements for conventional shaft sinking and raise drilling were described. Training program content was detailed in the form of module and lesson design approaches. In addition, the report recommends a method for developing, implementing and validating the training program. The authors conclude that such an implementation would meet the major objectives of improving the safety and efficiency of shaft construction work operations.

Jan 1, 1979