Search Documents

By Randy Martin

"Greenstone Resources Ltd. constructed and operates the Santa Rosa open pit, heap-leach gold mine in Veraguas, Panama. The project was commissioned in 1995 at a designed capacity of 1.8 million tons per year. The ore exhibits a long leach up to three years, and requires three stage crushing to minus 3/8 inch to achieve on average a 74% gold recovery. The crushing plant is required to handle high volumes of clay and the circuit includes a Barmac Crusher. Panama receives over 3 meters of rain annually and Greenstone is using innovative means to control the project's water balance. Greenstone has developed a successful approach to operating a low grade (1.5 gm Au/T) deposit under difficult operation conditions.ABSTRACT ONLY"

Jan 1, 1997

By W. Petruk

The silver-rich cobalt-nickel arsenides ores of the Cobalt area in Ontario, Canada were mined for silver from about 1904 to 1985. The ores contained about 8 oz to 100 oz Aglt and about 1 wt% Ni and 2 wt% Co. They were processed by gravitational techniques, screening and flotation to produce separate silver and Fe-Co-Ni arsenide concentrates. The silver concentrate was smelted, and in some cases the arsenide concentrate was sold to custom smelters which recovered silver and other metals. The ores display a wide variety of textures and contain many minor and trace elements. This paper presents an evaluation of mineral characteristics that have a bearing on extractive metallurgy and smelting of this type of ore.

Jan 1, 1993

By Luis G. S. Sobral, Gabrielle N. Bard

Copper sulphides Concentrates, from the flotation process of copper primary ore; contain, commonly, small amounts of precious metals, such as gold and silver. During the smelting process of those concentrate all gold and silver are practically in the blister copper, which is cast into anodes. Those copper anodes are electrorefined in an electrolytic system, where the electrolyte is an acid copper sulphate solution, where a high purity electrolytic copper is produced (>999,9/1000). The slime when submitted to an oxidative leaching process, using sodium hypochlorite and hydrogen peroxide as oxidizing agents, turn those metals into solution. This research practical work, apart from concentrating effort on the digestion of the anode slime, aims at evaluating the efficiency of the cementation process of the metals of interest for the separation of them to take place. 141

Jan 1, 2008

By I. K. Chopde, M. M. Dhobe, C. L. Gogte

"The quality of machined surface is becoming more and more important to satisfy the increasing demand of component performance and its reliability. While machining any component, it is necessary to satisfy the surface integrity requirements. Heat treatment plays an important role in improving the characteristics of the material.This work investigates the effect of heat treatment on the surface characteristics of AISI D2 tool steel after Wire-Electro Discharge Machining (W-EDM). The test specimens were prepared by hardening and tempering and then machined with Wire-Electro Discharge Machining process. Optical and scanning electron microscopy, surface roughness and micro hardness tests were conducted to study the surface characteristics of the machined surface. After characterization based on microstructures and test results, it is observed that the recast layer droplets are of smaller size with reduced white layer thickness resulting in higher hardness and lower surface roughness.IntroductionWith the development of mechanical industry, the requirement of alloy materials having high hardness, toughness and impact resistance is increasing. At the same time the quality of machined surface is becoming more and more important to satisfy the increasing demands of component performance and reliability. When machining any component, it is necessary to satisfy the surface integrity requirements. Surface integrity has two important parts. The first is surface texture, which governs mainly surface roughness. The second is surface metallurgy, which concerns to the nature of surface layer produced in machining [2]."

Jan 1, 2012

By K. Rajani Kanth

Environmental problem is the major concern for any industry and there is a great need to that along green lines. Sangam Dairy being one of the most famous and wide spread Dairies in India, produces wide spectrum of milk products. The BOD levels of effluent water of this industry with MIF treatment were found to be around 100 ppm. Lot of research has been expended in the past to bring down the BOD levels to bare minimum. The main objective of the present study is to minimize the BOD level to the required level stipulated by environmental standards by employing various seeding materials. For this purpose microbes like Bacillus Subtiles, Pseudomonas, Aspergillas, Staphylococcus, and Pencilium have been employed and BOD levels were analyzed. Various Reagents, solutions with different dilution levels have been successfully prepared. Initial and final Dissolved Oxygen levels were determined before and after incubation. From the DO data, BOD was evaluated for all samples and comparison analysis of various seeding material was carried to suggest the efficient seeding material for the ETP plant. In the process, solutions of different dilutions have been prepared using difficult reagents. These samples are treated with above mentioned microbes and BOD levels are estimated. It has been observed that staphylococcus and Pseudomonas proved to be the best seeding materials. When there microbes have employed BOD levels fall to less than 10 and 20 ppm respectively

Jan 1, 2006

By Guo-hua Bai, Hong-jing Yuan, Qian Li, Yong-bin Yang, Tao Jiang, Yan Zhang

"The effect of different additives on the bio-oxidation of arsenic-bearing gold ores has been carried out to solve the problems such as long period of leaching, low oxidation rate. The oxidants strengthen the cathodic reaction and thus improve the leaching rate by the increase of electron transfer. Meanwhile, silver catalysis is also effective for the decomposition of arsenicbearing gold ores due to the strengthening of anode reaction. Co-intensification by oxidants and Ag (I) is more efficient to the bio-leaching and the conversion of As (III) because the anode and cathodic reaction of biological oxidation of sulphide ores were both strengthened. The leaching rate reached to 63.94% after bio-leaching 13days by co-intensification of Ag (I) and Fe(III).IntroductionWith the worsening global ecological problems and the gradual exhaustion of available gold resources, metallurgical technology of refractory gold ore has received more and more attention and become possible due to its good advantage of the economic effects and negative effects to the environment. Refractory gold ore, the direct cyanide leaching rate of that is defined as less than 70%, has become an important raw material in gold extraction industry, in which sulfide bearing gold ore represents a large proportion, pyrite and arsenopyrite (FeAsS) is a common gold-bearing mineral. Since the gold is often encapsulated in the crystal lattice of these minerals, destruction or alteration of the ore to liberate the submicron and/or structurally bond gold is necessary[l]. Even if the ultrafine grinding approach also is generally not sufficient for these refractory ores and additional techniques like roasting, pressure oxidation and bacterial oxidation are used to liberate the gold [2]. In the three pretreatment processes, bacterial oxidation is characterized by its new ideas, low cost, no pollution, simple equipment and operation, high leaching index and become the most promising process which has received much attention over time [3-5]. But its further application is limited by some of its own shortcomings, such as long pretreatment time and the toxic effects of arsenic to bacteria on bio-leaching limit."

Jan 1, 2013

By Songlin Zhang

"The McCoy/Cove mine, located in Eureka-Battle Mountain trend of Nevada, is a gold and silver deposit. Case studies of recoverable reserve estimation for gold and silver were made using multiple indicator kriging and volume variance correction. The grade tonnage distributions of recoverable reserves were constructed and compared with the distributions defined by blast hole assays. Optimal pits were generated by Whittle 4D pit optimization package to analyze the impact of different processing recoveries at different economic cutoffs. The results were compared with ordinary kriging. The study indicates that the proposed method for multi-mineral recoverable reserve estimation is more accurate than kriging in tenns of grade and tonnage. The method of using recoverable reserves for pit optimization will maximize global reserve recovery and revenue, and is more efficient than condition simulation regarding computing power.ABSTRACT ONLY"

Jan 1, 1997

By Ray D. Peterson, Annette Revet

The optimization of secondary aluminum furnaces is critical to the efficient operation of a recycling facility. Since all metal loss occurs in the drosses, physical and chemical analyses of these by-products are valuable diagnostic tools. Dross analyses can provide information concerning total furnace metal recovery efficiency as well as identifying areas for potential improvements. A complete dross analysis is a labor-intensive process that requires significant care both in sampling and performing the analytical techniques. Experiments can be done at a bench- or plant-scale depending on the facilities available. This paper outlines the benefits and information that can be generated through dross studies. Furthermore, several analytical methods are discussed as well as the special requirements needed to gain accurate results. Experimental data from industrial studies is provided to demonstrate the use of dross evaluations for ~ace optimization.

Jan 1, 2000

By Rachel De Lucas

Current methods of hydrogen storage are an impediment to the transition of our energy infrastructure from a hydrocarbon to a hydrogen base. The transportation, handling, and storage costs of hydrogen gas account for a majority of its selling price. Magnesium hydride slurry is a safe, environmentally friendly alternative for hydrogen storage. If this form of storage is to be adopted on a large scale, a cost-effective method for recycling the enormous amounts of magnesium hydroxide byproduct must be identified. The solid oxide membrane (SOM) process can be used to recycle the magnesium hydroxide byproduct into magnesium metal, which can be reformed into magnesium hydride and reused for fuel storage. Conventional magnesium extraction/recycling technologies require a great deal of energy and create byproducts that are harmful to the environment and human health. The SOM process poses none of these detrimental effects and requires less energy and feed preparation. The economic viability of a facility that utilizes the solid oxide membrane process for the direct reduction of magnesium must be examined in more detail if industry is to consider it. Cost analysis data related to the commercial viability of a scale-up will be compared to two standard industrial processes: current magnesium production techniques including electrolytic and metallo-thermic processes. We have shown in our cost comparison that the SOM process is cheaper than these traditional techniques and that it is also comparable to aluminum's Hall-Héroult process in cost but with none of the environmentally harmful byproducts.

Jan 1, 2006

By D. L. Stewart

"Melt loss is usually one of the highest individual cost items in the operation of ah ingot casting facility. While melt loss and the resulting cost for the entire facility is usually well known (at least via standard cost accounting), dross generation and melt loss for individual unit operations within the plant are usually not known. Thus, the financial impact of various practices, alloys and scrap types is not known. Development of an accurate, relatively low-cost technique for measurement of melt loss at commercial scale would aid in understanding melt loss for existing units, as well as evaluation of the melt loss impact of alternate processes.This paper will describe a methodology developed at Alcoa for accurate and inexpensive measurement of melt loss at commercial scale. The methodology has been used to evaluate the impact of scrap type, melting practices, and dross treatment technology on melt loss."

Jan 1, 2000

By Mitsuhiro Ohtaki, Tetsuzo Arakawa, Fujio Murata

Refining of Zn from aluminum scrap melt by some vacuum distillation processes was studied to promote aluminum scrap recycling. Effects of distillation conditions, such as melt temperature, vacuum pressure and holding time, on Zn distillation behavior were investigated theoretically and experimentally by 0.3kg/ch scale vacuum resistance furnace. Three methods to increase the surface-area/volume ratio of liquid metal, such as gas atomizing, mechanical atomizing and mechanical stirring, were tested to increase the Zn distillation rate in 5kg/ch scale vacuum resistance-furnace. It was easy to lower the remaining Zn content to less than 0.1 wt% within one minute by mechanical stirring method. A water-model simulation experiment indicated that a significant agitation of the melt by stirring would be effective to increase the distillation rate. Continuous agitation vacuum distillation process (CA VP) has been designed and the pilot plant is now in construction.

Jan 1, 2000

By I. Van de Voorde

In this paper, results are presented concerning the search to implement Supported Liquid Membranes (SLM) Technology for the recovery of copper, nickel and zinc from electroplating and other effluents to prevent metal waste. A study of the influence of the individual parameters and of their combined effect on mass transfer in small-scale laboratory equipment has been performed, enabling to set forward the appropiate operating conditions for a pilot plant installation. The SLM pilot plant has been tested extensively, including short and long term runs, with real process solutions. It was demonstrated that the SLM technolgy is applicable for solutions containing 800 mg/L of metal ions, but also to the treatment of solutions with low metal content of origin other than plating shops. It was demonstrated by system analysis that the recycled salts are usable to produce metal electrolytes (for example Watt's nickel bath).

Jan 1, 2003

By F. San Martin, Y. Lefevre, F. Tamargo

The San Juan de Nieva smelter was commissioned in 1960 with an electrolytic zinc capacity of 15,000 t/y. After a number of minor expansions, the capacity was increased to 320,000 t/y in 1991 and will reach 440,000 t/y by August 2001. The expansion involves the construction of a 900 t/day Lurgi roaster and a new acid plant. The leaching will be fully revamped and modernised, including the construction of a new building for residue treatment and for j arosite precipitation with a separate circuit for silver-containing concentrates. The project also includes the construction of a fully automated 137,000 t/y zinc cathode tankhouse fitted with 3.4 m2 cathodes designed by Asturiana de Zinc, and based on the existing tankhouse and introducing some improvements. New melting and casting facilities, also designed by Asturiana, will be constructed.

Jan 1, 2000

By C. Allen

A series of zinc chloride electrowinning tests was carried out in a laboratory scale cell to evaluate the effect of temperature, current density, electrolyte composition, gas sparging and additives on the performance of the cell with respect to current efficiency, voltage, specific energy consumption and deposit morphology. The anode material was DSA for chlorine evolution and the cathode was made of aluminum. At 400 A/m2 current density, a current efficiency of 90.9%, a voltage of 3.4 V and an energy consumption of 2.78 kWh/kg were observed. Air sparging was found beneficial but was not pursued for health and safety reasons. Various additives in the same chemical family as tetrabutyl ammonium chloride (TBAC1) were tested. Both TBAC1 and tetrabutyl ammonium bromide were found to be equally effective. Attempts to carry out the electrolysis at 1200 A/m2 were not as successful.

Jan 1, 2000

By Wantae Kim

In order to establish the optimized recovery process for heavy minerals from Korean beach sand, we investigated the several physical separation methods such as gravity and magnetic separation followed by mineralogical characterization. There was clear relationship between the particle size and heavy mineral content that heavy minerals were mostly concentrated in the particles below 100mesh. Gravity separation using the spiral and shaking table separators made it possible to concentrate heavy minerals by rejecting the light and coarse particles consist mainly of quartz and other non-valuable minerals. The high-intensity magnetic roll separator and subsequent induced magnetic separator were applied to fractionate magnetic particles according to their magnetic susceptibility. The content of TiO2 of high susceptible ilmenite-rich fraction was 43.98wt.% while those of ZrO2 of non-magnetic and magnetic residue were 6.78wt.% and 3.11wt.%, respectively.

Jan 1, 2006

By Jian Wang, Hongyang Cao, Binxiu Wu, Junhong Li, Jimin Wang

"The enrichment and separation of scattered metal indium component in the pressure leaching solution with sulfuric acid from vacuum furnace germanium slag were studied by iron substitute and P204 extraction, which is supplied by shaoguan smelter. The experimental results show that the extracting power of P204 for indium from pressure leach solution is powerful. The optimal technological condition were the ratio of P204 and sulphonating serosene 3:7, phase ratio 1:3, solution pH 1.2, and extracting 5 minute. The enrichment indium solution of 21.7 g/L In at 95.2% recovery ratio was obtained by three-stage counter flow extraction and four- stage counter flow stripping.IntroductionScattered metals, such as Indium and germanium, were inriched as intermediate product or by-product during the metallurgy process of other non-ferrous metals, such as lead, zinc, copper and tin. For example, the indium and germanium were inriched in vacuum furnace germanium slag, which is the by-product of zinc vacuum distillation operation from hard zinc. It is difficult to recovery the indium from the vacuum furnace germanium slag, because the indium content is low, and the chemical composition and phase compositon were complex.Recovery indium from bearing indium zinc slag was researched extensively, such as pressure acid leaching, high temperature evaporation, solvent extraction method[l-7], acid leaching method has the advantages of high leaching rate, which can be separated hydrochloric acid, sulfuric acid and silicon fluoride acid systems. Solvent extraction method has the advantages of low production cost, fast reaction speed, high enrichment ratio, and simple operation."

Jan 1, 2013

By Lijuan Li, Xin Xia, Junjun Huang, Qijie Zhai, Xiang Jiang

"Some experiments with different temperatures (1173, 1223, and l273K) and different annealing times (3, 4, 5, 6min) were carried out on cold-rolled plate of Fe-36Ni invar alloy. The microstructure and the mechanical properties were observed and tested respectively, and the fracture morphology was observed by SEM. The results show that with increasing of the temperature and the annealing time, the austenite grains gradually grow up accompanied by a small amount of annealing twin crystals, meanwhile, its plasticity and toughness are improved, and it is typical ductile fracture under the condition of tensile failure. After annealed at l223K, the invar alloy has better comprehensive properties than that at the other annealing temperatures, and the grains size is more uniform. Furthermore, when the annealing time is 4min, the invar alloy has the best comprehensive properties.IntroductionAs we known, most metals and alloys expand with increasing temperature. More than one hundred years ago (in 1897), Guillaume observed that Fe-Ni alloy with face-centered cubic (fcc) crystal structure, consisting of36%Ni, showing a very small thermal expansion coefficient below the ferro-to-paramagnetic transition, the thermal expansion coefficient around room temperature( <2 X 1O-6K-1 compared to most metallic materials which have a thermal expansion coefficient of 10-20 X 1O-6K-1) [1,2]. Since then, the subject has attracted many researchers, and various alloys with low thermal expansion coefficients have been developed. These alloys, generally known as ""invar alloys"", are in demand where dimensional changes due to variation in temperature must be minimized and where high stability is required [3, 4]."

Jan 1, 2012

By Padmavathy Mahadevan, Samir Chefai, Eduard Guerra

"Electrocoagulation is a technique for treating wastewater streams from metallurgical plants whereby electrodes are corroded to generate gases (most notably oxygen at the anode and hydrogen at the cathode) and solid particulates which acts as substrates for coprecipitation of impurities. The performance of electrocoagulation reactors, in terms of their efficiency for removing a particular impurity, is highly dependent on several factors, most notably: the nature of the electrodes, the spacing between electrodes, the current density, the height of the electrodes, the solution flow rate, and application of periodic current reversal. Because these variables have complex interactions, in order to ensure reliable scale-up of laboratory results, experiments should be conducted under conditions that closely match those that would be employed at an industrial scale. To that end, this article describes the design and commissioning of a versatile laboratory scale electrocoagulation reactor that allows for the control of all the aforementioned variables along with the ability to measure the instantaneous spatial distribution of current within the reactor.IntroductionArsenic is often removed from metallurgical waste streams in stirred tank reactors by coprecipitating it with ferric ions as an arsenical ferrihydrite [ 1]. Electrocoagulation is an electrolytic technology that can accomplish the same task, but has not yet been widely adopted to treat metallurgical waste streams [2]. The electrocoagulation process involves the use of an external DC power supply to drive the dissolution of a relatively non-toxic metal into the wastewater stream, usually either iron or aluminum, which then largely precipitates as oxyhydroxide phases that adsorb undesired impurities [l]. At the anode, the metal is dissolved and oxygen is often evolved, lowering the local pH and enhancing metal ion solubility."

Jan 1, 2012

By Albert W. Spitz

Profitably recovering copper and precious metals from copper bearing scrap is a demanding and frustrating combination of art, science and economics. With fluctuating markets, varying raw materials and increasingly stringent environmental regulations requiring process revisions, practically everything is changing. The volatile copper market constantly shifts the percentage of copper in the scrap that can be economically processed. Scrap that has value one day may incur a disposal cost the following day. Also with less copper in the scrap, more residuals, slag, fume, etc. are generated which frequently present disposal problems and infrequently generate income. The ever increasing amounts of electronic scrap add value to the copper produced by virtue of the precious metals present. Printed circuit board materials create more slag and organic off gases which must be treated. Finally, the emphasis on reducing emissions of organics and other metals, especially lead, is a continuing challenge. Stack gases, fugitive emissions and ambient air quality all demand constant surveillance.

Jan 1, 1997

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

Sensor controlled sorting is a promising technique for the upgrading of scrap aluminium alloys. In a universal detection system of Delft University characteristic features are extracted · from the material particles by means of cameras. Examples are size, texture, edge-structure, homogeneity, and colour pattern. Additional sensors are added for higher selectivity: electromagnetic detection, light transmission, spectral reflection and more. Signal processing theory learns that a classification of particles fundamentally improves as the number of independent features increases. At the laboratories of the Delft University a test bench is available for the development of advanced multi-sensor quality control and sorting systems. It is based on a software system for detection, segmentation and classification of particles, which was especially developed for this application. Work is now in progress for high-speed detection and sorting of non-ferrous alloys, including aluminium casting and wrought alloys. A recently developed actuator design enables positive sorting into more than 3 fractions of particles that are randomly orientated on a flat conveyor belt.

Jan 1, 2000