Search Documents

By David R. Brosnahan

Increased Cu grades due to chalcopyrite-rich ore from The Doe Run Company's new Casteel Mine prompted a program to increase Cu recovery. Preliminary tests indicated that prohibitive quantities of FeS2 float with chalcopyrite. Point counting of mill stream samples showed that locking was not a major problem, although grinding to finer particle size enhanced the floatability of both chalcopyrite and marcasite. Backscattered electron images and microprobe analyses of FeSz minerals revealed the presence of Pb which appears to occur as solid solution in marcasite, and as a sub-micron particulate Pb phase in pyrite.

Jan 1, 1987

By Zhou Shu-cai

"A method has been proposed for the pre-treatment of high phosphorus iron ore by carbothermic reduction assisted with microwave irradiation and magnetic separation on a laboratory scale. Chemical analysis of the reduced ore sample, the metal sample and the slag sample were conducted. Based on the above research, the influences of carbon addition, microwave power and microwave irradiation time on the recovery of Fe and dephosphorization were discussed. It indicated that the increase of microwave irradiation time and power had substantial effect on the recovery of Fe while the influence of carbon addition was not obvious and the highest iron recovery ratio reaches some 95.5% when the dephosphorization ratio was 37.68%. A high iron recovery ratio and a reasonable dephosphorization rate were incompatible under the conditions investigated in this study due to the reduced iron and because unreduced P-contained gangues were not efficiently separated. This method may provide a reference for the future utilisation of high-phosphorus iron ore.IntroductionWith the rapid growth of crude steel production in China, the source of iron ore tends to become increasingly strained and is facing the risks of raw material shortage for the iron and steel industry. In order to decrease the production cost, China has to focus on the utilization of its domestic low grade iron ores for the iron and steel plants [1-2]. China has a large deposit of high phosphorous iron ore with a reserve of 7.45 billion tons which is unused in any large scale [3]. Therefore, the development of a successful and economically viable technology for high phosphorus iron ore is of profound importance. To remove phosphorus from the high phosphorus iron ore, several mineral and metallurgical processes have been proposed, such as bio-leaching [4], roasting reduction plus melting separation [5], pre-reduction and screening methods combined with mechanical crushing or air jet milling[6] selective agglomeration plus reverse flotation [7]. However these processes are not cost effective or are time consuming. The traditional pyrometallurgical process( BF+ BOF) refuse this kind of ore mainly because that molten iron is saturated with carbon or high carbon content and thus all phosphor us in the burden goes to the molten iron[8]. Therefore, it is important to exploit the cheap and abundant high phosphorus iron ore as a resource in ironmaking. In recent years, the microwave was widely introduced as a heat resource for extractive metallurgy of iron ore or other minerals. For example, microwave assisted ore milling, microwave assisted carbothermic reduction of metal oxides and microwave assisted mineral leaching issues[9-10]"

Jan 1, 2014

By Lucas L. da Costa, Sergio N. Monteiro, Romulo L. Loiola, Tammy G. Rodrigues Portela

"The fibers extracted from the petiole of the buriti palm tree are relatively strong as compared to other lignocelluloses fibers, with a potential for composite reinforcement. In this work, polyester matrix composites incorporated with these fibers were investigated for their flexural behavior. Specimens with up to 40% in volume of continuous and aligned buriti petiole fibers were bendtested until rupture. The results showed an increase in both the composite mechanical strength and the stiffness with incorporation of these fibers. A fractograph analysis by SEM disclosed a moderate adhesion mechanism between the buriti petiole fiber and the polyester matrix. This mechanism is apparently responsible for the improved performance of the composites.IntroductionIn recent years, the substitution of energy-intensive synthetic materials for natural ones is being considered in many industrial sectors including automobile, packing and textile [1]. A typical case is that of natural fibers, mainly those obtained from cellulose-based plants also known as lignocelluloses fibers. They have being investigated in the past two decades, aiming to replace synthetic fibers, particularly the glass fiber, commonly used as polymer composite reinforcement [2-8]. From the engineering point of view, lignocellulosic fibers present today important environmental, economical, societal and technological advantages already discussed [7-8]. Moreover, several lignocellulosic fibers are known since the beginning of our civilization and still cultivated or naturally extracted all over temperate and tropical regions of the world. According to Kalia et al [1 ], these fibers can be classified by their origin, as shown in Table 1."

Jan 1, 2011

By Zhen Zhang, Jiang Diao, Tao Zhang, Yi Ren, Lu Jiang, Xiao-Man Yan, Bing Xie

The precipitation behavior of phosphorus enrichment phase was investigated by slag modification with Al2O3. The mineral phase of the original slag and modified slags were measured by mineral phase microscope, SEM+EDS and XRD. The mechanism of Al2O3 modification was discussed according to the thermodynamic theory analysis software (Factsage version 6.3). The results show that the high phosphorus solid solution (nˊ2CaO·SiO2-3CaO·P2O5) was generated by the continuous reaction of nC2S-C3P (nˊ＜n) solid solution and Al2O3 under 1350℃. The amount of initially precipitated solid solution (nC2S-C3P) was reduced and even disappeared with the increasing of Al2O3. If the addition of Al2O3 is enough in the slag, the high phosphorus solid solution (nˊC2S-C3P) that generated by the above mentioned reaction will continue to react with Al2O3 to produce Ca2Al2SiO7 and even C3P, which was demonstrated that the addition of Al2O3 has a positive influence on the precipitation of phosphorus enrichment phase.

Jan 1, 2015

By Atinuke Oladoye, David Esezobor

"Particulate Copper Silicon carbide (Cu-SiCp) composites find application as wear and heat resistant materials in electrical sliding contacts such as in homopolar machines, railway overhead current collector systems where high electrical/thermal conductivity combined with good wear properties is required. However, challenges occur during machining due to the presence of hard reinforcement in the matrix. This may lead to high turnover of tool wear and poor surface finish. The adoption of near-net shape technology to produce such hard-to-machine metal matrix composites and subsequent finish machining with its attendant cost has reported limited success. This paper critically appraises the challenges and opportunities in the improvement of tribological characteristics of particulate Cu-SiC composites and identifies low cost reinforcement material that could be used to improve its tribological characteristics.IntroductionTribology consideration is increasingly becoming a decisive factor in the design and selection of materials for applications involving interacting surfaces in relative motion. The consideration is mainly on the combined effects of friction and lubrication on material's wear integrity and performance amongst other. Annual losses due to tribology in the US industries are estimated at between 1-2% of the Gross National Income [1], in Russia it is about 1-4% of the GDP [2]. Thus, the attributes of tribology has become imperative in modem machinery especially those applications involving sliding and rolling surfaces, and electrical contacts [3- 8].These are readily found in homopolar machines, internal combustion engines, aircraft engines, gears, cams, seals and railway overhead current collector systems [9-12]. In these systems, the dissipation of frictional heat arising from the interacting surfaces as quickly as possible imposes constraints on the choice of materials for such application to prevent softening, plastic and shear flow and the transfer of metal as wear debris onto the interacting surfaces. If these possibilities occur, system performance is compromised and premature failure may result. Materials for these systems are expected to possess high electrical and thermal conductivities, low coefficient of thermal expansion, good corrosion resistance and high melting point [3-8, 13]."

Jan 1, 2011

By James R. Craig

The General Image Processing System (GIPSY) is being employed for the quantitative textural analysis of complex sulfide ores from the Southern and Central Appalachians and for the determination of liberation characteristics of the mineral constituents during grinding. Optical images from a microscope-mounted TV camera or from 35mm film are converted into digital images which are subsequently analyzed by GIPSY, a transportable image processing software package. Properties measured by GIPSY include spatial distribution of mineral constituents, grain sizes, grain shapes, grain orientation and mineral co-occurrences.

Jan 1, 1982

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes? are considered one of the most promising alternatives to well-established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic-containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment-technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (000). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Theodore Ineich

The “BIOMOre” project aims to prove the technical feasibility of indirect in situ bioleaching of sulfide minerals contained in a deep underground deposit, by bringing together the disciplines required to make a success. The underground location in Poland was provided by project partner KGHM inside an operating copper mine. Key components of this project were the design and construction of a pilot plant, and its operation in an underground environment. This project also included a ∼250 t (100 m3) fragmented rock reactor hydraulically connected to the pilot plant. The pilot plant consisted of several tanks and pumps, a fluidised bed ferric iron generating bioreactor containing immobilised acidophilic iron oxidation biomass, and all the required instrumentation and utilities. Before the bioleaching phase could start, the rock reactor had to be flushed continuously firstly with water to remove chloride salts that are corrosive and also harmful for the bacteria used in the bioreactor, and secondly, with sulfuric acid solution to react with the carbonates present in the ore matrix. This paper summarizes the design, construction, commissioning, and operation of the pilot plant.

By F. Baldini, M. S. Borges

"The proposed method emphasizes the optimization of waste management with regard to the exploitation of raw materials incorporated in the remains of industry, as well as the economics of natural resources as an environmental impact assessment. This system [tool] allows: (a) the conversion of an environmental liability into an asset by finding a line of appropriate research for each type of waste and the development of new materials applicable to other industries, (b) the performance of internal control of the waste generated (production, storage, final destination) as well as legal conformity.Objectives:1.1 General objective:To design a collaborative system for socio-environmental management of industrial waste.1.2 Specific objective:Develop evidence of concepts;Evaluate the deployment of the inventory of waste in an industry;Enable the conversion of an environmental liability into an asset by finding a line of research appropriate to the waste: a case study;Evaluate the environmental legislation in the legal mechanisms that influence company decisions.IntroductionThe global economy is undergoing major changes, among these changes; it should be highlighted those related to technological progress and environmental quality.While the industrialized countries and higher levels of economic growth dominate modem technology, developing countries are identified by a different growth pattern, using the annual growth rate of Gross Domestic Product per capita [3, 18].Growth is when the GDP grows, in percent, over the previous year. Development, on the other hand, is when the countries change their technologies and improve their internal structure. Thus, the growth considers the accumulation of wealth, while the development is concerned with the distribution of wealth, improvement of the quality oflife and environmental quality [3, 18].As the UNESCO report shows (1999), the biggest problem is between consumption and development, what is produced and the end that is given to the product. Therefore, product and by-product have equal importance in the quantity produced [29].On one hand there is a positive relationship between indicators of economic growth and technological progress, however, on the other hand, these transformations are a paradox, confirmed by the dramatic use of environmental resources and the lack of technologies for recycling of industrial scrap."

Jan 1, 2011

By Darrin Wikoff

"The data, compiled by the Department of Energy (DOE), indicates that the average industrial plant could reduce its total energy cost by 14.8% by implementing effective Life Cycle Asset Management processes. The actual savings varies by industrial classification, but in all cases the potential is substantial and could have a marked impact on the operating profit of the company.Improvements geared towards improving equipment reliability have distinctive linkages to environmental performance, such as reducing the amount of product and raw material waste through routine monitoring of system parameters through predictive technologies, and preventing interruptions to production cycles with a focus on Overall Equipment Effectiveness (OEE).Alcoa successfully reduced solvent disposal costs by more than 40% and GE reduced greenhouse gas emissions by more than 250,000 metric tons. This presentation will show you how companies have successfully reduced energy and disposal costs through a focused effort on manufacturing process reliability.IntroductionSmelter in the ParkThe quaint town of Portland, Victoria protrudes outward towards Antarctica from Australia’s southeastern coastline. Portland is a quiet rural community surrounded by agriculture that draws tourists by the thousands to the southernmost edge of Victoria by way of breathtaking cliff top views of the majestic Southern Ocean, the intrigue of shipwreck coves along the Great Ocean Road, and what most will call the eighth wonder of the modern world, the “Smelter in the Park”. Integrated within Portland’s beautiful landscape is a 356,000 ton/year aluminum smelter that stands as a symbol of collaboration between nature and industry. Nestled atop a ridge which faces “Sail Rock”, a popular destination of local and visiting fisherman, the smelter is engulfed in a mix of brush and wetland preserves that are home to many of Australia’s feathered and fourlegged natives. Also within its interior you’ll find parks and natural landscapes abundant where man and machines coexist with the native inhabitants."

Jan 1, 2009

By Guiming Yang, Xiaoxian Huang, Zhiyun Ji, Min Gan, Lishun Yuan, Xiaohui Fan, Zhiyuan Yu

"The roasting characteristics of hematite pellets containing MgO were studied where magnesia powder, serpentine and magnesite were used as magnesium-additives respectively. The mechanical strength of both preheated and roasted pellets decreased when MgO content increased, which implied the addition of MgO had an adverse effect on pellet consolidation. By adding flux containing CaO, the mechanical strength of both preheated and roasted pellets were improved. The addition of calcium flux facilitated the formation of calcium ferrite and provided a certain amount of liquid phase, resulting in faster diffusion ofMg2+ and Fe3+. The result showed that diffusing speed of Mg2+ was enhanced by 1.48 times, and rate constant of Fe203 crystalline growth was enhanced by 62% when basicity was around 0.4. Improvement of mineralization degree and recrystallization of Fe203 assisted in consolidation of hematite pellets containing MgO.IntroductionOxidized pellets are ideal iron-bearing burdens in blast furnace. At present, magnetite is the main raw material for oxidized pellet production in China. However, as the rapid development of iron and steel industry, resources of magnetite have been depleted and cannot satisfy the requirement of pellet production. Using hematite concentrates to produce oxidized pellets has become a trend [1, 2]. Many pellet enterprises abroad nowadays have adopted high proportions of hematite concentrates when producing oxidized pellets, e.g. the percentage is 100% in a lot of Brazilian factories [3, 4]. But high proportion of hematite concentrates will lead to low mechanical strength and high reduction swelling index of pellets. Some studies show that Mg-bearing pellets have excellent metallurgical properties, and the reduction swelling phenomenon can be solved by adding fluxes containing MgO [5, 7]. However, there are problems such as low pellet strength and bad roasting characteristics for MgO-bearing pellets, which remains an obstacle in pellet industry. Hence, it's vital to undertake the study on strengthening measures for indurations of Mg-bearing hematite pellets."

Jan 1, 2013

By Run Huang, Xuewei Lv, Songli Liu, Chenguang Bai

"Titanium alloy was prepared from titania-bearing blast furnace slag (Ti-BF slag) by aluminothermic process in an induction furnace. The effects of aluminum amount on the titanium silicon yield and titanium recovery ratio were studied. The phase transformation and chemical composition of the prepared alloy were investigated by X-ray diffractometry (XRD) and X-ray fluorescence (XRF) respectively. It was found that the mass fraction of silicon and aluminum increased with increasing the aluminum amount, however, the mass fraction of titanium increased first and then decreased with increasing the aluminum amount. Furthermore, both the titanium alloy yield and titanium recovery ratio increased with the increase of aluminum amount. The main phases of the alloy were TixSiy and AlTi3. The titanium alloy samples prepared in various conditions had a composition (wt.%): 38–50% Ti, 29-34% Si, 4-11 Al%, 1.6-2.2 Mn%.IntroductionPanzhihua and Xichang regions in the southwest of China are rich in vanadium-titanium magnetite containing iron, vanadium, titanium and gangue. According to the characteristics of the resource, iron and vanadium are successfully recovered with a blast furnace process and a converter process. However, most content of titanium are entered in the blast furnace slag with TiO2 22% -26% and metallic Fe 2%–6% called Ti-BF slag. Due to the dispersed distribution of Ti in various fine grained mineral phases with a complex combination between Ca, Al and Si, it is difficult to recover the Ti components[1]. This slag is generated at a current rate of 3.6 million tons per year, which adds to the existing 70 million tons of slag produced so far[2]. The slag has had to be piled as large as the mountains, which not only waste of resources but also cause a pollution of the environment. Therefore, the study of integrated utilizing Ti-BF slag has become very significant."

Jan 1, 2012

By Joël P. T. Kapusta, Romeo U. Pagador, Noparut Wachgama, Chumnoom Khuankla

"Thai Copper Industries (TCI) is a custom copper smelter and refinery in Rayong, Thailand, with an annual capacity of 165,000 tons of cathodes. It employs the El Teniente Technology as the primary smelting reactor to produce white metal from copper concentrates. The white metal is further treated in Hoboken Siphon Converters to produce blister copper then refined in anode furnaces before being cast into anodes for electro-refining in the on-site tankhouse.Thai Copper Industries is the first copper smelter to install and successfully operate on a commercial scale with the Air Liquide Shrouded Injection (ALSI™) Technology in the Hokoben converters with sonic injection of oxygen enriched air and nitrogen for cooling of the injector tip areas. Following commissioning and the establishment of operating practices, the performance of the Hoboken converters with ALSI™ Technology produced outstanding results. The unique combination of an El Teniente and Hoboken siphon converters, both of which are bath smelting operations, offers very high blowing and oxygen efficiencies. As a consequence, reverts recycling was accelerated with minimal build up on the mouth, end-plates or even below the siphon that is typical in Hoboken converters.These outstanding results in the Hoboken Siphon Converters with ALSI™ Technology helped the TCI Plant reach a production of about 75% of its capacity within four months despite the fact that the TCI staff is quite young and its converter know-how and experience are not yet fully developed."

Jan 1, 2009

By H. H. Kellogg

The thermochemical properties of molten solutions in the binaries Cu-Bi, Cu-Sb and Bi-Sb, as well as the ternary Cu-Bi-Sb, have been correlated and described in mathematical form by use of the associated species concept combined with the three-suffix Margules equations to account for the non-idea 1 behavior of the solution species. Agreement of the correlations with experimental data is excellent (relative deviation of less than 2.5% in the values of the activity coefficients) in most cases. The correlations are applicable over the entire composition range of each system, and in the temperature range 700°-1250°C.

Jan 1, 1985

By Jim Sundal

Primary steel manufacturers using electric arc furnaces generate one of the largest hazardous waste streams nationwide. The waste stream, known as electric arc furnace dust, is a listed hazardous waste with the designation K061. Oregon Steel Mills, Inc., (OSM) of Portland, Oregon, has implemented a process known as Glassificationn, which uses KO61 as an ingredient in an onsite recycling process. Because OSM was able to demonstrate that the Glassificationm recycling process beneficially uses all toxic constituents in the electric arc furnace dust and that the recycling process produces marketable products, the process is not subject to Resource Conservation and Recovery Act (RCRA) permit requirements. The marketable products manufactured using Glassificationn include roofing granules, ceramic glazes and colorants, abrasive blasting media and, more recently, synthetic slag fluidizers. The purpose of this paper is to identify the regulatory issues for recycling hazardous waste and demonstrate that OSM glass frit is effective as a slag fluidizer in primary steel manufacturing.

Jan 1, 1994

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Metallurgical and Materials Engineering Department at Montana Tech is investigating various methods of extracting and refining rare earth elements from mineral ores and concentrates. As part of this research, an elevated temperature “roasting” process has been evaluated as a means of converting the rare earth elements contained in various matrices to bromides as a pretreatment step in preparation for downstream rare earth element extraction and recovery operations. Laboratory and bench-scale experiments have been performed to assess the effects of varying temperature (150 to 400° C), time (1 to 4 h), and the ammonium bromide to rare earth oxide molar ratio (6 to 24) in the roaster charge. The results show that nearly complete bromination of the rare earth oxide is achievable when the roast is performed under optimum conditions.

Jan 1, 2015

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"To determine the heating rate of billets using ‘short coils’, an appropriate correction factor must be applied to the theoretical relationship. In 1945, Vaughan and Williamson published a semi-empirically modified Nagaoka coefficient applicable for moderate frequency induction heating processes (10 kHz). Recently it was demonstrated that the method of Vaughan and Williamson gives <10% error in the estimated power when heating aluminum billets at 50 Hz.In the present study, experiments have been conducted on aluminum billets in order to verify an empirical frequency corrected ‘short coil’ equation. Measurements of electrical conductivity (<± 0.5%), current (± 1%), heat (± 1-3%), and magnetic flux density (± 1-2%) have been performed. The results are compared with 1D analytical calculations, and 2D axial symmetric FEM modeling using COMSOL 4.2®. The frequency corrected equation has proven to provide accurate predictions of power (<4% error) within the frequency range 50 Hz to 500 kHz.IntroductionInduction heating is commonly applied to the re-heating of billets before forging or extrusion processes. The resistive heating produced by eddy currents in the solid or semi-solid work piece during this procedure, is driven by the time varying magnetic flux density in the air-gap between the work piece and the coil. The flux in the air-gap is created by the current flowing in the induction coil, i.e. the magneto-motive force. In Figure 1 it can be seen that the currents present in the work piece are concentrated in the outer ‘shell’, or the first electromagnetic penetration depth (dw), and flow in a direction which opposes the magnetic field produced by the induction coil."

Jan 1, 2012

By Zhonglin Ye, Yifeng Shi

"This paper has outlined forms of Au & Ag losses in copper smelting process and methods for increasing Au & Ag recovery, analyzed factors influencing Au & Ag recovery in copper converting process, presented Au & Ag behavior in copper electrorefining process, and reviewed effect of current density/electrolyte circulation rate during electrolysis and surface finish of cathode on Au & Ag losses. Measures and research direction for decreasing Au & Ag losses in electrolysis have also been introduced. Based on Au & Ag behavior in copper electrorefining process and previous studies by others, new approach for increasing Au & Ag recovery in copper smelter has been discussed. And brief comparison has made between continued multiplication method and equilibrium method application in the case of calculation of Au & Ag recovery in copper smelter.IntroductionAs gold and silver are the major by-products from copper smelting process, efficient Au & Ag recovery has become one of the key approaches for copper producers to increase economic efficiency. With similar physicochemical properties, Cu, Au and Ag belong to the first subgroup of elements in the same periodic table. Au and Ag will be enriched into Cu phase firstly when both matte-slag phase and copper-matte phase appear in copper smelting process. However, great changes have taken place in Au & Ag proportions into individual phase due to changes of physicochemical conditions in each smelting process. Metallurgists at home and abroad have carried out a great deal of pilot plant tests and laboratory tests in order to increase Au & Ag the former Soviet Union with regard to Au & Ag losses in copper smelting process in the 1970s and 1980s, and he proposed solutions to increase Au & Ag recovery in copper metallurgical plants. As more than 20 years passed, Jingchun Lu's paper, Discussion on Increasing Au & Ag Recovery in Copper Smelting System, remains as a literature of the most comprehensive study. Based on Jingchun Lu's literature, the authors of this paper discussed new approaches to increase Au & Ag recovery in copper metallurgical plants with combination of many researches done by other researchers for over 20 years."

Jan 1, 2013

By P. Halsall

Smelters of medium or low grade tin concentrates must recover a high proportion of tin from iron-bearing slags or concentrates; the volatility of tin sulphide makes possible the production of iron-free tin fume. Laboratory work defined conditions which would promote the sulphidisation of tin slags and concentrates melted with them, to result in tin recovery as fume, and a residue of less than 0.5% Sn content, which could be controlled to vary with the value of tin. Subsequently pilot-plant work on 6-tonne and 15-tonne scale led to a commercial plant of 45 tonne. capacity (1962), for melting and fuming primary and secondary low-grade tin materials by submerged combustion. Some factors contributing to the rate of Working expressed in terms of the &apos;half-life and the amount of work done, the &apos;half-life-tonne&apos; are studied, leading to the design and operation (1972) of the 100-tonne water-jacketed unit, presently in use, treating a wide range of slags and low tin-content ores and residues.

Jan 1, 1983