Search Documents

By Dengfu Chen, Yi Yang, Chunmei Chen, Mujun Long, Shikai Gong, Junhao Sheng, Tao Liu

The relationship between thermo-physical properties of petroleum coke and temperature is of importance for determining of the operating parameters during the calcining graphitization process. In this paper, the variations of thermo-physical properties of petroleum coke versus temperature were investigated, such as the DSC-Tg curve, the specific heat capacity, the thermal diffusion coefficient, the thermal conductivity, and so on. The thermal analysis curve of petroleum coke showed synchronous thermal hysteresis at higher heating rates, indicating that a larger heating rate will cause delay of thermal effects. The thermal diffusivity of petroleum coke decreased during the calcining process. With increasing temperature, coefficient of heat conductivity and specific volume heat of the petroleum coke increased with a decreasing variation rate. The research provides a database for the calcining graphitization process of petroleum coke.

Jan 1, 2015

By M. del C. Ruiz

The extraction of Nb and Ta from a columbo-tantalite of San Luis, Argentina, is being studied by using a pressure reactor and HF as leaching agent. The reagents and products have been characterized by several techniques such as scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDXS), X-ray fluorescence (XRF), X-ray difracction (XRD), surface area (BET) and size particle analysis. Experimental results have shown that the extraction of niobium and tantalum increases with increasing temperature, reaction time and acid concentration. For particle size between +80 and -355 mesh no significant changes are detected. It is also slightly affected by the stimng speed. XRD analysis of the residues did not show formation of new crystalline structures.

Jan 1, 1999

By Dengfu Chen, Yunwei Huang, Mujun Long, Kui Lv, Pei Xu, Lin Bai

The surface temperature of continuous casting slab in the secondary cooling zone is a key parameter of production control. However, the accuracy of radiation temperature measurement of high temperature casting slab is greatly affected by the environmental factors, such as water vapor, spray, water film and other participational medias during continuous casting process. In this paper, the radiation characteristics of water vapor and its influences to radiation temperature measurement of continuous casting slab were investigated. Based on the database HITRAN 2004 and the measuring principle of monochrome thermometer & colorimetric thermometer, the measuring errors under different operating infrared spectral wavelength were compared. Results showed that spectral region with wavelength nearby 1.0μm or 1.6μm would be the optimum for high temperature infrared thermometer used under the conditions with moist steam, water spray and water film at the secondary cooling zone in steel continuous casting.

Jan 1, 2016

By Deming Wang, R. A. Overfelt

"This paper presents a computer-aided heat transfer simulation method to predict the thermal characteristics of an alloy sample in a special furnace for directional solidification. A two-dimensional transient heat transfer by conduction combined with radiation is developed to calculate the energy exchange between a directional solidification furnace and the sample. Finite difference equations with control volumes are used to calculate the transient heat transfer. A special boundary control volume is used to combine heat conduction and radiation in the transient heat transfer. Heat radiation effects on the surfaces of the special control volumes with a changeable view factor during directional solidification processing are also represented. The simulation results are verified by measurable experimental data. Using the computer simulation model, many thermal properties of the directional solidified castings can be obtained, such as temperature distribution, solidification velocity, the shapes and positions of the liquid/solid interface and thermal gradient at the interfaces. These are very important to analyze microstructure of casting alloys, avoid casting defects and control casting quality. 1 IntroductionIn directional solidification (DS) processing of castings, the temperature distribution, the interface between liquid and solid zone, thermal gradient in the mushy (pasty) zone and solidification rates are very important factors to analyze the microstructure and the casting quality. These variables affect the orientation and size of dendrites, shapes of grains, solute segregation and deleterious casting defects, such as microporosity, freckles and segregation channels. In order to avoid the casting defects, the temperature distribution and thermal gradients of castings during directional solidification must be strictly controlled. However, the structure of furnaces used for directional solidification is often complex. Heat transfer and temperature distribution within a casting not only depend on furnace temperature but also on the thermal properties of the casting alloy, crucibles, retorts etc. A more accurate heat transfer analysis."

Jan 1, 2001

By R. J. Mitchell

Results from investigations into impurity distributions over cathodes are presented with implications for various sampling methods, Selection of an optimum treatment procedure for the test sample is outlined. The impact of both these studies on the development of an in-house method for sampling Isa Process cathode is discussed. The economic compromise actually undertaken, satifying wants and needs to sustain confidence in high grade cathode purity is detailed.

Jan 1, 1987

By Katsutoshi Inoue, Shafiq Alam

Several novel types of chemically modified chitosan were prepared by immobilizing functional groups of EDTA and DTPA onto polymer matrices of chitosan in order to investigate their potential for mutual adsorptive separation among rare earths. Following the batch wise adsorption tests to elucidate their basic adsorption characteristics for rare earths, mutual separation was carried out using a column packed with the chemically modified chitosan. The separation between Sm(III) and Y(III) was tested using a column packed with EDTA-type chitosan while mutual separation among 4 light rare earths, La(III), Ce(III), Pr(III) and Nd(III) was tested using a column packed with DTPA-type chitosan. In both cases, satisfactory mutual separation was achieved by the chromatographic operation using these chemically modified chitosan.

Jan 1, 2014

By Cleusa Cristina Bueno Martha de Souza

Hydrometallurgical techniques for processing metals are becoming an efficient method for recovering metals. Although batteries' manufacturers have got rid of mercury content, some efforts have been made for recovering other metals enclosed in the battery formula. This paper discusses the bench scale experiments in the purification process of leached solutions from alkaline spent batteries. After leaching process using sulfuric acid as leachant, the solutions containing Fe, Cd, Pb, MIl, Zn and K were neutralized to precipitate iron hydroxide. In a second step, the purification experiments were carried out with excess of zinc dust to try to remove Cd while Mn and Zn still remain in the solution to be recovered in an electrolysis stage. The purification experiments procedures were conducted at different temperatures and times to find out properly conditions from the viewpoint of metals removal After filtration the solutions were submitted to chemical analysis to certify the metals content extracted.

Jan 1, 2001

By Noritaka Horii, Katsuyoshi Kakinuma, Hiroshi Yamamura

"ZrO2 and Y2O 3-doped ZrO2 gel film were obtained by spin coating of sol from Zr-n-propoxide, n-propanol, acetylacetone, nitric acid, and water on a silica glass as a substrate. ·Dried gel films crystallized to monoclinic, tetragonal, cubic and their mixed phases, depending on the chemical composition of sol, .firing temperature, and coating cycles. ZrO2 films with highly preferential orientation were successfully obtained from a solution containing a large amount of n-propanol. The highly oriented ZrO2 film was found to have high transparency compared with non-oriented 'films. Electrical conductivity of 8 mol% Y2O 3 doped ZrO2 film was also measured.Introduction3 mol% Y2O 3 doped ZrO2, which has a tetragonal symmetry is ·well known to have a strong mechanical property and a high toughness. (1) On the other hand, 8 mol % Y 2O 3-doped ZrO2 is high oxide-ion conducting material and is applied to oxygen sensor, oxygen pump, and solid oxide fuel cell (SOFC). (2) Sol-gel methods using metallic alkoxide are widely applied for synthesizing ceramics such as high-purity fine particles, thin film, and fiber. (3) For ceramics films, many reports have been made on SiO2, (4) TiO2, (5) and PZT. (6) Several case studies have been done on zirconia film based on the sol-gel method, (7) - (11) but very few on preferentially oriented film and on systematic Y zO3 doping. Almost zirconia ceramic· films reported were prepared by means of dip-coating. Kamiya et al. (12) and Ganguli et al (13) converted zirconia into fiber. Sol from Zr alkoxide is usually very unstable, and a stabilizing agent such as glycol or ß-keton is used beforehand (7) (14)."

Jan 1, 2000

By Ting Lei, Mingjun Rao, Guanghui Li, Tao Jiang

"With the rapid development of iron and steel industry, the supply of iron ores can not meet the present demand for iron and steel industry in China. Large reserves of oolitic hematite have been discovered with low iron grade (30% ~ 45%) and high phosphorus content (0.4% ~ 1.8%). Traditional processes for utilization of this ore are characterized as either high cost or low dephosphorization. In this study, sodium salts-modified paigeite (SSMP) was added to enhance on the dephosphorization of high-phosphorus oolitic hematite by using reduction roasting followed by magnetic separation. Various parameters, including the amount of SSMP, reduction time,reduction temperature, grinding fineness and the magnetic field intensity were investigated. As a consequence, a magnetic concentrate of metallic iron powder with total iron grade of 93.2% and phosphorus content of 0.08% was obtained under the optimal conditions. The results also provide a potential avenue for the comprehensive utilization of paigeite ore.IntroductionOolitic hematite is currently recognized as one of the most refractory iron ore resources in the world. Over 4.0 billion tons of reserves of such resources have been found in China, and more than 10 billion tons in the long-term. This kind of ore is characterized as low iron grade (30%~45% TFe) and high phosphorus content (0.4%~1.8% P), as well as fine particle size distribution of ferrous minerals (the size distribution varies from 5~30 µm, even less than 2 µm) and the complex association between iron and other gangue elements [1~5]. The unique structural characteristics of the high phosphorus oolitic hematite make it difficult to obtain high iron recovery and good dephosphorization efficiency by using the conventional processes [1,2]. Traditional processes are characterized as high cost and low dephosphorization for oolitic hematite beneficiation [9~15]."

Jan 1, 2012

By Jianhua Xin, Min Chen, Jin Xu, Hui Li, Nan Wang, Ming Chen

The kinetics study of blast furnace dust (BFD) recycling with flash reduction process at high temperature has been carried out using a high temperature drop tube furnace in laboratory scale. A combination characterization methods of chemical titration and SEM-EDS were used to track the reduction kinetics. The experiments using CO and CO2 mixtures with range of CO/CO2 (1:0, 1:1) at different temperature (1623–1723 K) and at different reduction time (1560– 2340 ms) were conducted. It was found that the reduction degree increases with the increase of temperature and reduction time as well as CO concentration. The carbon contained in the original BFD has weak in fluence on the reduction potential in the form of gasification. The unreacted core model was adopted based on the observation of the cross section and the measurement of iron element content, the effective diffusion coef ficient and reaction rate constant were determined and the rate controlling step was also analyzed.

Mar 1, 2018

By Catherine Cai

A granular sorbent, prepared by gel-coating polyethyleneimine (PEI) on high surface area silica followed by crosslinking with a low-molecular weight diepoxide, has significantly higher uranium capacity, greater salt tolerance, and faster kinetics than the commercial resin Dowex 21K. Though having lower U(VI)/Fe(III) selectivity than Dowex 21K, the gel-coated PEI affords much higher sorptions of both U(VI) and Fe(III) and also their separation by selective stripping with acid.

Jan 1, 1999

By Maria D. Salazar-Villalpando, Anthony Cugini, Bryan Reyes

"The electrochemical reduction of CO2 was performed in a laboratory-made, divided Htype cell. A copper electrode was used as the cathode. An Aldrich Nafion 117-type ion exchange membrane (0.18mm thickness) was used as the diaphragm. NaHCO3 and KHCO3 were studied as the catholytes. Hydrogen evolution from water reduction and products from CO2 electrochemical conversion were recorded. Higher CO2 reduction enhancement was observed by KHCO3 as compared to NaHCO3. The main conclusion of this work is that in fact CO2 can be electrochemically reduced with copper electrodes.1.-INTRODUCTIONThe direct electrochemical reduction of CO2 may allow for a simple process and, by avoiding high temperature reactors, would enable the process production rate to be quickly varied to follow the time of day availability of surplus electricity [1]. Temperature has a major effect on the electrochemical conversion of CO2 since its solubility increases when temperature decreases [2]. The electrical potential applied to the electrochemical reacting system will have an influence on the product distribution, as well. For example, a narrow potential range during cyclo-voltagraphic studies will determine the detection of a lower number of products. A recommended potential range to study the electrochemical reduction of CO2 is -2V to 2V. Moreover, the reaction rate on the electrode is governed by various processes, such as the kinetics of electron transfer, adsorption/desorption at the electrode surface, and diffusion of CO2 to the Cu electrode. The availability of active species, CO2 for electro-reduction, is extremely low at the vicinity of the electrode surface and it seriously interferes with the rate of mass transfer. In batch type electrolytic reactors, depletion of CO2 at the surface takes place first. CO2 from the bulk then has to diffuse to the electrode surface, resulting in mass transfer controlled kinetic phenomena. During the above process, several other competitive side reactions could suppress the primary reaction even though the cathode has good electro catalytic properties for reduction of carbon dioxide. When the dynamic supply of specific active species is ensured to electrode surface, the mass transfer effects are minimized to certain extent. Hence it is envisaged that a continuous flow reactor is more efficient for the electro-reduction of CO2 in CO2 saturated aqueous electrolytes. The primary reactions that occur at the copper electrode during the reduction of CO2 are listed below (with the standard potentials calculated using formation energies [1] :"

Jan 1, 2010

By Zuomei Jin

A laboratory study was conducted on the separation of Zn, Pb, Cu and Ag from a finely dissem-inated interlocked silver-rich multimetal sulphidc ore. These are often difficult to separate from each other by flotation. The thermodynamic calculations of Zn-S-O, Cu-S-O systems at different tem¬peratures were presented on predominance diagrams. Based on these diagrams the optimum temperature and gas composition were selected for roasting. The results of separating Zn, Cu from calcine by neutral leaching and acid leaching were found to be satisfactory. The distribution of silver in the roasting and leaching processes were tested. A flow sheet was proposed.

Jan 1, 1993

By Rajesh S. Ransing

An intelligent tool has been developed to analyse the quality of diecast components. The influence of both design and process parameters has been studied in great detail. The tool, based on expert systems related technologies, can identify the causes for the defective castings manufactured. Design related causes such as gate position; gate area, runner design etc. as well as process related causes such as cycle time, cavity filling time and melt temperature are suggested by analysing the data on defective castings for a manufacturing campaign. This intelligent analysis is useful for both design as well as production engineers in the decision making process. All the causes for the occurrence of defects are classified into two categories. The firs category is the 'rootcauses' i.e. the causes which are related to the actual process, material and design parameters and which can be directly monitored. The second category is more abstract in nature and is classified as `metacauses'. These capture the scientific rationale implicit in the cause and defect relationships. This knowledge on causes and defects is represented in the form of a structured graph rather than by a set of rules, which, coupled with forward reasoning and heuristic search techniques results in an elegant and efficient approach. Uncertainties and the degree of relationship among causes and defects are represented by a fuzzy probabilistic model.

Jan 1, 1994

By M. Z. Sukiennik

A static method for vapor pressure measurement up to 1450 K and above 1 hPa is presented. The method is designed for equilibrium and kinetic studies of metallic systems, including those with a chemical reaction. Application examples are given for determination of activities in condensed phases, and heterogeneous reaction rates and equilibrium constants.

Jan 1, 1993

By Zhenyang Wang, Yiran LIU, Xiangdong Xing, Jianliang Zhang, Zhengjian Liu

Basic characteristics of marine placer were systematically studied by chemical analyze, scanning electron microscope and X-ray diffraction in this paper. It could be found that the marine placer mainly consists of titanomagnetite and titanohematite. A series of experiments were performed to investigate reduction-magnetic separation for Fe and Ti from the marine placer. Effects of reduction temperature, reduction time, carbon ratio, magnetic density, and grinding fineness on the reduction-magnetic separation process were investigated. And the optimal process parameters were obtained as follows: the reduction temperature 1300, the reduction time 30 min, the carbon ratio 1.1, the magnetic density 50mT, and the grinding fineness of 0.074μm 86.34%. Under such conditions, the metallization rate, iron grade of magnetic substance and iron recovery reached to 94.23%, 97.19% and 90.28% respectively, and the titanium grade in non-magnetic substance and recovery of was 57.94% and 87.22% respectively. The effective separation of iron and titanium could be achieved in reduction-magnetic separation process.

Jan 1, 2015

By Suman Das, Justin J. Gambone, Rohan Bansal, Ranadip Acharya, Paul Cilino

"This paper focuses on generating a quantitative microstructure prediction model for Scanning Laser Epitaxy (SLE) process based on coupled flow-thermal modeling using Finite Volume method. SLE is a laser-based additive manufacturing process for the deposition of equiaxed, directionally solidified and single-crystal nickel superalloys through the melting of alloy powders onto superalloy substrates. In the current work, the detailed effects of natural and Marangoni convection on the flow field are studied and the results are analyzed in terms of the temperature gradient, vorticity parameter, melt pool dimensions and mushy region extent. The detailed property data of the processed superalloy and the laser scan path are incorporated in the model to predict the microstructure in realistic scenario. An optimization study is carried out to evaluate the critical parameter values at which the columnar-to-equiaxed and the oriented-tomisoriented transition take place. This work is sponsored by the Office of Naval Research through grant N00014-11-1-0670.IntroductionSLE is a laser-based additive manufacturing process for the creation of structures in equiaxed, directionally solidified and single-crystal nickel superalloys through the selective melting and resolidification of superalloy powders. In SLE, a tightly focused laser beam is guided by a highspeed galvanometer scanners allowing for tight control of the amount of energy being applied to the top of the powder bed, as well as the speed at which the melt pool moves across the substrate. Under the proper operating conditions and with sufficient substrate meltback, the solidification microstructure follows the morphology of the underlying substrate, allowing for directional and even SX growth.Several reports on the modeling aspects of laser cladding-based additive manufacturing approaches can be found in the literature. Approaches based on Finite Element Methods (FEM) and Finite Volume Methods (FVM) are employed for the thermal modeling of the system [1, 2]. Gaumann coupled the Columnar to Equiaxed Transition (CET) modeling with the Rosenthal solution in earlier work based on laser cladding [3]. Rappaz et. al. provided a detailed modeling of the microstructure/columnar orientation based on the solidification velocity and crystalline orientation [4]. This approach is based on the selection of the growth direction that closely follows the melt pool normal direction. Later on, substrate orientation is also taken into account [5, 6]."

Jan 1, 2013

By Stein Tore Johansen

Some ferro-silicon furnaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the?off?gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels close to the furnace is observed. The result is irregular stops to clean the off-gas channels. The paper focuses on the nature of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By Zhi-biao Yin

Copper smelter flue dusts often cannot be directly recycled to the smelting process and accumulate as hazardous wastes requiring environmentally acceptable disposal. Because of the limited amount of flue dust, a separate copper extraction process must be simple and require-a small plant investment. A flue dust process has been developed, consisting of the following steps: (1) roasting a pelletized mixture of hydrated lime and flue dust to fix arsenic and sulfur as insoluble calcium salts, (2) heap leaching the roasted pellets with a buffered ammonia/ammonium salt solution to extract copper as an ammine complex in a lined cell that is the final repository of the leached pellets, and (3) boiling ammonia from the lixiviant to precipitate copper. Condensed ammonia and the filtered solution are returned to leaching. Heap leaching in the final repository cell lowers the capital investment significantly compared with competing extraction processes. Chemistry with respect to arsenic, sulfur and copper is discussed.

Jan 1, 1992

By Thomas Niehoff

Many industrial processes require energy. Energy is required for melting or heating purposes. The heat can be generated by electrical heating or combustion/oxidation of hydrocarbons. Oxygen supports the combustion process. Oxygen is naturally contained in air with about 21 vol.-percent. The use of technical oxygen will allow an increase to the natural oxygen concentration of combustion air. Altering the combustion process by increasing the oxygen content has various effects. These effects are described and analyzed with regard to heat transfer, emissions and energy consumption. Industrial processes requiring oxyfuel are described and discussed regarding energy aspects.

Jan 1, 2008