Search Documents

By Bora Derin

The partial pressure ratios of sulfur and oxygen for several copper flash smelting plants were derived using the Reddy-Blander (RB) model and predicted dissolved sulfur contents available in the literature. The sulfide capacities (Cs) of six different flash smelting plants (FeO-CuOo.5- CaO-MgO-FeOu-AlO15-SiO2) slags were calculated. The log (PO2/PS2) versus matte grades of various industrial processes was determined. The PO2/PS2 ratio increased with an increase of copper grade. The calculated partial pressure ratios for the copper flash smelting are in good agreement with those of the experimental data.

Jan 1, 2003

By Entov Vladimir M., Gilmer R. Burgos, Andreas N. Alexandrou

"Processing of metal alloys in their mushy state represents a new trend in metal processing. As part of this process, known also as thixocasting, a specially prepared slurry at a temperature in the mushy region is injected into a die. Parts produced using this technology offer better mechanical properties than those produced by casting, and comparable to those of forged alloys.In thixocasting, semisolid slurries are highly concentrated suspensions of rounded rosette-like crystals in eutectic liquid. The mechanical behavior of the slurry is determined by the structure and properties of the skeleton formed by the alpha phase particles. The skeleton structure is almost never at equilibrium, and its evolution is, governed by a number of kinetic phenomena of different c11'aracteristic time-scales. Therefore, the skeleton structure depends on the mechanical and thermal history of the material. As a result of these kinetic processes, the rheological properties of the material, such as effective viscosity and yield stress, decrease with structure breakdown, and increase with its development. In the present investigation, the behavior of semisolid slurries during processing is modeled using the conservation equations, and a Herschel-Bulkley fluid model. The rheological parameters are assumed to be functions of the solid volume fraction, and of a structural parameter that changes with processing history. The evolution of the structural parameter is described by a first order kinetic differential equation that relates the rate of build-up and break-down of the solid"

Jan 1, 2000

By Tadashi Aiura, Yasuhiro Miura

"A small amount(0.2mass%) of Scandium(Sc) was added to the 7.NOl and 5083 Al alloys as a refiner and stabilizer of microstructure, and the resulting microstructures were discussed in comparison with the effects of the conventional additives. The followings are summarized: 1) in the as-solidified structure, a ·decreased tendency of constitutional supercooling and increased solubility of Mg were recognized for the Sc-added 5083 alloy. Sc is a -better microstructure refiner for the 7N01 alloy than Zr, in a sense that it does not suppress the favorable effect of· coexisting Ti. 2) Sc effectively suppresses recrystallization both in the 5083 and 7N01 alloys. 3) The rod like primary Al3Sc crystals formed during solidification, as well as the fine dispersion of Al3Sc precipitates formed by subsequent heat treatment, can act as a strong recrystallization suppresser. IntroductionThe 7N01 and 5083 alloys are the most popular industrial Al alloys and they are widely' used for various structures because of their superior properties. Fine macro and micro structures of the materials are required for obtaining acceptable sec resistance,consistent appearance of anodized surface and good weldability, as well as good mechanical properties. In order to produce fine grain structures, transition metals, such as Cr, Zr, and Mn, have been conventionally added.It has been reported that Sc is an efficient refiner [l, 2] and can be an alternative for the conventional and also suppresses recrystallization in Al alloys [3,4]. Scandium is the lightest transition element and forms an equilibrium intermetallic phase. The equilibrium phase, Ll2-Al3Sc, is coherent with the matrix, and of _spherical shape. A fine dispersion of the spherical precipitates is obtained by quenching and aging after solutionizing annealing. The authors have already reported a part of the experimental results on the effect of Sc on the as homogenized microstructure of the 5083 alloy [5]. In the present study, the effects of Sc on the macro and micro structures of the industrial high strength Al alloys(7N01 and 5083) for extrusion are investigated, and the superior role of Sc as a grain refiner is shown"

Jan 1, 2000

By Peng Bing

Stainless steelmaking dust is classified as a hazardous waste due to higher than acceptable heavy metal leachabilities such as zinc, lead, cadmium and chromium. In addition to being an environmental hazard, the flue dust is also an economical concern to stainless steelmakers as it contains large amounts of valuable alloying elements, especially for iron, chromium and nickel. A new technology of direct recycling of stainless steelmaking dust has been developed to recover the metals from the dust. But it was found that zinc was accumulated in the dust collection system in practical run of direct recycling. This study focuses on the effect of the operating parameters such as temperature, dust feed rate and the ratio of CO to dust on the reduction of zinc oxides present in the dust. The mathematical model for the reduction process was setup based on the experimental research. According to the mathematical model, the temperature has obvious effect on the reduction of zinc. It is benefit to the process of zinc reduction to increase the temperature. But the temperature will not be the main factor for the reduction process after 1228C. It will promote zinc reduction to decrease the dust feed rate and control the ratio of dust to CO. It was also found from the experiments that ZnFe2O4 in the dust could be decomposed at high temperature. Decomposing ZnFe2O4 in the dust increases the recovery of zinc from the dust distinctly.

Jan 1, 2006

By Zizheng Zhou

The separation of cobalt from other base metals can be achieved using diffusion dialysis in a two-compartment reactor separated by an anion exchange membrane. In this work, a Neosepta AFX membrane was used to study the separation of various metals in an acid-chloride solution. The separation of one metal from another was investigated on the basis of the various chloro-complex stabilities. The metals investigated included cobalt, nickel, copper(II), iron(III), aluminum, zinc and cadmium. The impact of several critical experimental conditions, including the initial metal and chloride concentration in the feed solution and their initial concentration in the receiving solution, on the separation factor and the metal transfer rate is reported in this work. Effective separation of different metal pairs was achieved under the experimental conditions.

By Guillermo J. Román

The precipitation of copper and zinc as cements from a copper alloys' spent pickling solution has been studied at laboratory and pilot scale, with the objective of designing an economic process to recover both metals and render a solution to be either recycled to the pickling process or treated in a standard fashion and produce a non-hazardous sludge. The sulfuric acid spent pickling solution already containing copper and zinc was used first to dissolve another solid residue originated in the copper alloys foundry to neutralize part of the acidity. The resulting enriched solution was treated separately with two reductants,; sodium borohydride and iron powder varying pH and excess of reductant under constant agitation. Under the best conditions, precipitation of over 95 percent of zinc and copper was achieved together with the reduction of lead and cadmium contents respectively. A process for the combined residues treatment is proposed.

Jan 1, 1995

By Metehan Erdogan, Ishak Karakaya, Fuat Erden

"Mg-Ni system draws attention due to the promising hydrogen storage properties of Mg2Ni. The proposed method involves the use of NiO and MgCl2 in an electrochemical cell to from Mg-Ni intermetallics directly. The electrodeoxidation of NiO was followed by combination of Mg and Ni in molten salt electrolytes. The products were characterized by XRD analysis and SEM examinations. The quantitative results from Rigaku supported by Rietveld Refinement method conducted by Maud showed that more than 50 percent of the input Ni was converted to Mg-Ni intermetallics.INTRODUCTIONIt is well known that fossil fuels are the most common energy producing materials throughout the last century although, they are not renewable and their usage cause critical environmental problems [1, 2]. Hydrogen, on the other hand, is known as a clean, renewable energy carrier and instead of fossil fuels; usage of hydrogen for energy production will be the benefit of mankind. However, there are problems that hinder more common usage of hydrogen such as hydrogen storage [3]. Mg2Ni is known as Mg based hydrogen storage material with high hydrogen storage capacity [3-6]. Common Mg2Ni production methods are; mechanical alloying [8-11], vacuum induction melting [12, 13], vacuum arc melting [14], combustion synthesis [15], melt spinning [16], repetitive rolling [17] and isothermal evaporation casting [18] were also used. However, in all of these, pure Mg and Ni are required to be produced previously. Therefore, difficulties arise during handling, preparation and combination of Mg and Ni due to highly reactive nature of especially magnesium (i.e. oxidation of Mg) [11, 17, 19, 20]. Although hydrogen desorption dynamics can be significantly improved with usage of nanostructured Mg2Ni [7], it is difficult and it requires very long processing durations to produce nanostructured Mg2Ni by above processes."

Jan 1, 2014

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Hara Prasanna Mishra

"In the Sukinda Valley of Orissa, India, the total quantity of nickel ore reserves comprising of both lateritic and chromite over burden(COB) have been estimated at around 231 million tonnes containing 0.3 to 0.9% Ni. While mining of one tonne of Chromite ore, around 6-7 tonnes of chromite over burden are removed. These overburden materials are disposed as waste materials, which causes lot of environmental hazards and ecological imbalance. India imports a large amount of nickel and ferro-nickel to meet its growing demands in various sectors. For import substitutions, efforts have been made to produced ferro-nickel from the lean deposits of nickel bearing lateritic ores/ chromite over burden materials by reduction roasting followed by magnetic separation and then the nickel rich magnetic fraction is smelted to produce ferro-nickel. It has been possible to produce ferro-nickel of grade varying from 4-25% nickel.IntroductionDuring mining of chromite ore, large quantities of overburden materials are being generated. The materials amount to approximately 10 million tones per year contain around 0.3-0.9% Ni, 0.02-0.06% Co, 20-50% Fe and 4-9% Cr2O3 depending upon the location and the depth of the mine. These materials presently do not find any application for the extraction of nickel due to lack of a suitable technology. The materials are also unsuitable for ferro-nickel making because of their very high iron to nickel ratio. The country is seriously looking for a suitable technology to utilize these resources as its entire domestic requirements of nickel is met though imports. In this connection, a systematic approach has been made at the Institute of Minerals and Materials Technology, Bhubaneswar to develop a process for ferro-nickel making from this indigenous resource."

Jan 1, 2011

By Paponetti B. . A.

Gold is usually recovered by cyanidation, thiourea leaching and amalgamation, however the efficiency of these technologies, in the case of refractory ores, is low ever when fuie grinding is practised. For example, .if the gold particles are included in sulphide minerals, the leachant cannot reach them, so they are often lost in the tailings. Hence .it is first necessary to break the sulphide crystals by preliminary treatment such as roasting, nitric .acid oxidation, pressure leaching and bacterial oxidation and then apply a conventional extractive technique for satisfactory gold recovery. This paper describes the effect of biological pre-treatment with Thiobacillus ferrooxidans) on the? extraction ? and? recovery of gold by conventional cyanidate. leaching from; a refractory arsenopyrite ore from Golcuck (Turkey).

Jan 1, 1991

By Ki Bui Ma

Momentum wheels with superconducting bearings can integrate both attitude control and energy storage functions, with attendant savings in the total volume and weight of hardware, and power consumption, all of which are in short supply on mini-satellites. We have built and tested a prototype with a wheel of mass 1.9 kg, diameter 3.25 in, and height 3 in, which can store 3.5 J-sec of angular momentum and 5 kJ of energy when it rotates at an angular speed of 15000 RPM. The energy density of 2.5 kJ/kg achieved is comparable with the lower range for lead-acid batteries. To show that the wheel is energy efficient, we have performed spin down tests and measured the input power required to sustain rotational speed. Results indicate that power consumption, even accounting for the needs of cooling system, is significantly smaller than that for state of the art commercial reaction wheels.

Jan 1, 2002

By Don Ibana

The use of solvent extraction (SX) in process metallurgy is particularly attractive as it is applicable to a wide range of solute concentration and pH, and it allows complete separation of chemically similar metals such as nickel and cobalt and the rare earths among others. It is therefore applicable to the processing of low grade and complex ores, which is increasing and expanding owing to the diminishing reserves of quality ores, and this has driven the increasing and expanding use of SX.The current SX technology, however, has inherent limitations owing to the use of mechanical agitation as it induces high shear mixing. Excessive shear produces very fine droplets, and while this favours mass transfer, it also leads to sluggish phase separation. High shear mixing is also known to favour crud formation. All these factors as well as high power and reagents consumptions contribute to poor process efficiency. Electrostatic solvent extraction (ESX) is similar to conventional SX except that mechanical agitation is replaced with electrostatic agitation. In direct contrast to mechanical agitation, it allows the production of very small droplets that can be made to maintain intense motion, which favours mass transfer, without affecting the phase separation. In addition, as it uses an electrostatic field, the power consumption is minimal. Hence, it promises to be a superior alternative to conventional SX mixing although an application of the technique is yet to be achieved.Our work to develop an application of the technique in process metallurgy has now established that electrostatic field has no effect on either the stability of the reagents or the chemistry of the process. A volumetric flowrate that is comparable to that of a conventional sieve plate pulse column is achievable. We have also established that electrostatic fields can be made to yield much narrower droplet size distributions than those of mechanically agitated contactors, and they allow better control of droplet motions, which include oscillation and linear motion and hence, mass transfer. These are significant advancements toward our goal and shall be discussed in this presentation.

By Carlos Ortiz

The Huelva Flash Smelting Furnace was commissioned in September 1975. The Smelter and the Acid Plant were expanded in 1995 to their present capacity of 300,000 tpa new copper equivalent and one million tonnes of concentrate per year. During these years of operational experience, most of the initial practices have been reviewed, process control has drastically improved and main process equipment has been modernised. The fourth Flash Furnace campaign lasted 9 years (1995-2004) during which 8 million tonnes of concentrate were smelted. Increasing sulphur content in concentrates and new environmental requirements imply new challenges for smelters to keep production and operation costs down. This paper is an overview of the modifications and improvements carried out in the 2007 general shutdown in Smelter and Acid Plants. Al

Jan 1, 2008

By J. Y. Hwang

Microwave heating is an attractive alternative to conventional heating methods because heat is generated directly within the microwave absorbing materials. It has potential to be utilized for selective heating and removal of specified components from a materials mixture. This investigation was undertaken to explore the potential of selective heating and burning of binders for foundry sand reclamation. Selected raw materials and binders used in foundry operations were tested to determine their receptivity to microwave heating. Time needed to reach 600°C and/or the maximum temperature achieved for samples irradiated by microwaves for twenty minutes under 800 W microwave power are reported. The microwave heating characteristics of the selected materials are summarized and discussed. The interactions between microwaves and the raw materials used in a foundry. such as silica sand. chromite sand and bentonite (clay) binder were studied. The results showed that chromite sand coupled well with microwave energy at ambient temperature while silica sand did not. This was expected because the major component of chromite sand. iron chromite (FeCr2O4). is a good microwave absorber. while quartz, which is the major component of silica sand, is a microwave transparent material at ambient temperature. Bentonite absorbs microwaves well because it contains a hydroxyl functional group and water molecules in its structure. It was found that the structure of bentonite was changed through microwave irradiation. Microwave heating characteristics of silica sand mixed with different amounts of bentonite binders were investigated. The presence of bentonite in the mixture improved the microwave heating of silica sand significantly. and bentonite was deactivated by the microwave processing.

Jan 1, 1995

By James E. McNulty

Today's energy era is the beginning of a transition from the Petroleum Age to a future age of renewable fuel resources. Fuels for the transition era will come from unconventional sources and conversion technology. Affecting the practicability of transition technologies are attitudes of the public, capital requirements and availability, patterns of fuels utilization, producibility of fuels and the actions of governments. Primary energy sources to replace deficiencies of oil and gas and provide growth in the period of transition will be coal, oil shale, nuclear energy and peat.

Jan 1, 1981

By Min Chen, Lei Xu

Sintering behavior and performance of high alumina refractory based on the ternary subsystem MgAl2O4-CaAl4O7-CaAl12O19 were investigated using ZrO2 as an additive up to 8 wt.% by solid state reaction sintering. It was found that the added ZrO2 could dissolve in the CA6 grains in the form of a solid solution, which enhanced the isotropic growth of CA6 grains and then improved the sintering. As a result, the densification process was improved and areas with enrichment of ZrO2 showed a more compact structure. With further increase of ZrO2 addition, tetragonal ZrO2 were found to locate in the grain boundaries for exceeding the solid solubility limit, which enhanced the thermal shock resistance, indicating that addition of ZrO2 exhibited a positive effect on sintering behavior and performance of this refractory. In addition, it is considered that the optimal amount of ZrO2 addition was about 4% considering the performance together with the cost.

Jan 1, 2015

By Ajay K. Singh

The surface quality demands for galvanized and galvannealed steel sheets by the automotive and appliance industries have been getting increasingly stringent over the past few years. Intensive efforts by Hot-Dip-Galvanizers to meet these demands have resulted in substantial improvement to the hot dip coating process. However, elimination of zinc bath contaminants which directly affect the coated strip surface quality continues to remain a tough challenge. As part of our effort to improve the zinc bath cleanliness, Inland Steel Company has developed a test method to quantitatively measure the contaminants in incoming zinc spelters and establish a specification for incoming zinc quality. The test is currently being used for auditing the incoming zinc quality. The zinc suppliers are also using this test for quality control purposes. The purpose of this paper is to describe the test method and how it has improved the galvanizing operation at Inland.

Jan 1, 1992

By A. Van den Steen

In the early fifties Professor Breckpot of the Louvain University in Belgium in collaboration with the Research Laboratory of Metallurgie Hoboken, discovered the possibility to separate nickel from cobalt sulfate solutions by a nickel sulfide depolarized cementation. This reaction, completed later with a zinc precipitation, was developed into purification processes for the Shituru and Luilu Gécamines cobalt plants in Zaíre. Due to increasing demand for higher quality products and the necessity of lowering the production costs, more laboratory and pilot plant investigations concerning the key parameters for the nickel and zinc sulfides precipitation were under- taken. Especially the relative stabilities of cobalt, nickel and zinc sulfides, precipitated with elemental sulfur or sodium hydrosulfide, were examined in relatlon with the pH and with the redox potential. These investigations have led to better plant practice and new development possibilities. The valorisation of the precipitated sulfides has also been considered.

Jan 1, 1988

By Chuanfu Zhang

Based on Thermogravimetric and Differential thermal analysis (TGA-DTA), porous copper powder is prepared by thermal decomposition of complicated copper oxalate. The effects of various conditions on the morphology, crystalline grain size and specific surface area of copper powder were investigated, including temperature, duration, mixing ratio of nitrogen and hydrogen. Furthermore, composition and morphologies of the products were characterized by X-ray diffraction (XRD), Scanning electron microscope (SEM) and BET adsorption isotherm. It is found that porous copper powder was produced under optimum conditions. The specific surface area is over 6.74 m2?g-1, and average pore size in particles is about 30.3 nm. After comparison of SEM images, the final product Cu well inherits the morphology of the precursor, thus a mechanism of in-situ decomposition is proposed.

Jan 1, 2009

"EAF dust is categorized as a hazardous solid waste. EPA approves only two treatment methods: either sending the dust to zinc recycling facility, or stabilizing it first and then disposing it to a specially-lined landfill. Both treatment methods are costly to EAF steelmakers. In order to reduce the cost and even better to make profit from the dust, EAF steelmakers need to find a costeffective technology to separate zinc from EAF dust. This paper is dedicated to discussion of a novel recycling strategy: in-process separation of zinc from EAF dust. The concept of in-process separation of zinc from EAF dust is first defined, and then a simple Zn concentration model is developed. From this model, two approaches of in-process separation of zinc from EAF dust are derived: (1) prematurely capturing dust at very high temperature when zinc is still in vapor status, (2) prematurely collecting dust immediately after quickly cooling EAF off-gas from high temperature to low temperature. Next, thermodynamic analysis is conducted to understand zinc behavior in EAF off-gas. It is demonstrated in theory that zinc is in vapor status while it exits from electric arc furnaces. At last, recycling routes and economics of in-process separation of zinc from EAF dust are discussed.IntroductionElectric arc furnace (EAF) plays an increasingly important role in steel production. According to USGS, steel production from electric arc furnaces has long exceeded that from basic oxygen furnaces [JJ. In 2009, electric arc furnaces produced 64% of total steel in the United States.Along with the fast growth of EAF steel production, generation of EAF dust is also rapidly increasing. A survey by AIM Market Research showed that 10 - 20 kg EAF dust was generated for every ton of EAF steel produced [2] In 1999, the United States alone produced 770,000 metric tons of EAF dust [3] In Europe, annual generation rate of EAF dust is more than one million tons [4-5]. In Japan, about 450,000 tons of EAF dust is produced each year [6] Globally, total generation of EAF dust was estimated to be more than 5 million tons per year [5] EAF dust is categorized as a hazardous solid waste since it often contains heavy metals, such as lead, chromium and cadmium. US Environmental Protection Agency (EPA) approves only two methods for treating EAF dust: (1) recycling the dust by EAF-dust recyclers, and (2) specially landfilling the dust for disposal after it is chemically stabilized. These two methods of treating EAF dust are both very costly to EAF steelmakers. It was estimated that a fee of $150 to $200 per ton of EAF dust was paid for various treatment options, which added approximately $2 - 3 cost for every ton of liquid steel produced by electric arc furnaces [?J."

Jan 1, 2011

By U .. C. Rojas, J .. C. Gomez

"Fire Refined Copper (EI Teniente Three Stars) has been produced at Caletones Smelter of Codelco Chile since almost the beginning of its operations.Due to changing features of the copper market, together with the targets on technical efficiency and productivity, it has become more and more relevant for copper industry to reach both, good final product quality and a proper environmental control.At present, copper refining process at Caletones Smelter takes place in two cylindrical tilting furnaces, where solid fluxes are injected through horizontal tuyeres into the molten bath. (Fig. N2 1)Solid reagents are pneumatically conveyed and injected into the liquid copper bath attaining excellent solid - liquid contact, so the impurities removal efficiencies are found to be high. Same injection tuyeres are used to introduce both oxidising agent (normal air) and reducing agent (reformed gas) into the molten bath. Air or nitrogen is used as conveying gas for solid reagents, depending on the process stage.This pap~r gives a fundamental description of the process and industrial results related to the injection of blend of sodium and calcium carbonates to remove arsenic and antimony, silica and granulated reverberatory slag to remove lead and a mixture of calcium carbonate and mineral coal to reduce the selenium content of the fire refined copper."

Jan 1, 1996