Search Documents

By E. S. Geskin

"This paper is concerned with the construction of a formal technique for the selection of a metallurgical technology. Exergy consumption is used as the criterion of process efficiency. Different items of the exergy balance are considered and techniques for the reduction of exergy consumption are determined. The selected techniques of exergy saving enable us to identify processes which should be used at different stages of steelmaking. The combination of the selected processes enables us to suggest a technology for conversion of iron ore into steel products. The selection of this technology narrows the range of further search of metallurgical processes. The paper shows that qualitative thermodynamic analysis can be used as the first step in the design of metallurgical processes. IntroductionThe existing processes for making, shaping and treating of steel enable us to convert the available iron bearing ores into marketable steel products. However, the energy cost of metal production is much higher than thermodynamically required, while the metal properties are much lower than thermodynamically available. Increasing cost and declining availability of energy and raw meterials make the creation of new steelmaking technologies imperative. In recent years, the number of novel processes for the making, refining, and shaping of steel have been suggested and tested. Some found a practical application. However, the tested technologies make up a small portion of the physically available routes for the conversion of iron ore into a marketable product. It is also not evident that the optimal routes have been tested and that the selected technologies are the best among those tested.Although the development of new metallurgical technologies must be based on the experimental and practical information, the number of the alternative routes for the making, shaping and treating of steel, as well as the cost of examining each single route, make necessary the use of analytical techniques for the evaluation of the possible ways of process development."

Jan 1, 1988

By J. Alberto Vázquez M.

A sensor employing yttria-stabilized zirconia (YSZ) was used to determine the oxygen activity of molten copper at laboratory scale at temperatures of 1200° and 1300 dc. The reference electrode was a Ni-NiO mixture. The amount of the deoxidizing agent (CU3P) ranged from I to 3% of the mass of copper. Thermodynamic analysis of the Cu-O-P liquid system was carried out to predict the required deoxidizing agent and the final composition of the molten copper. Both results, calculated and experimental, show that the oxygen removal is more efficient at lower temperatures. The kinetics of the deoxidizing reaction is very fast in the first minutes of the treatment. A metalography analysis of rapid cooled samples show the oxygen and phosphorus distribution

Jan 1, 2003

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to sulphide smelting plants. In both primary smelting and converting. gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992

By V. G. Papangelakis

The implementation of a flow-through yttria-stabilized zirconia (YSZ) sensor for pH measurements in high temperature and concentrated electrolyte systems relevant to hydrometallurgical processing of nickeliferous laterites is discussed. Instrumentation involved the use of a custom made flow-through titanium electrochemical cell. Accuracy and validity of the pH measurements at temperatures up to 250C were assessed using concentrated sulphate process solutions ranging from synthetic binary sulphuric acid ? water solutions to progressively multicomponent metal ? sulphate solutions simulating laterite Pressure Acid Leach conditions. The measurements were also compared with theoretical models using recently obtained thermodynamic data. A difference of ±0.25 pH units was observed between measured and calculated pH values at temperatures. This is an acceptable difference given that these are the first direct high temperature pH measurements ever on the concentrated acidic sulphate solutions. This result is encouraging more research for the development of industrial electrochemical systems for direct pH measurements in autoclaves.

Jan 1, 2003

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997

By C. A. Natalie

Prediction of average residence times for different particle size intervals during sulfide roasting was investigated. Calculations were done to predict average residence times using a model which employs empirical correlations for elutriation constants. Experimental average residence times were determined using a continuous., six inch diameter,. fluid bed roaster and compared with calculated residence time values. Comparison of calculated and experimental data showed that geometry effects may have .been significant when attempting to apply elutriation data to this roaster.

Jan 1, 1985

By K. S. Raja, M. Misra, S. K. Mohapatra

"Ordered arrays of TiO2 nanotubular photocatalysts were prepared by a simple anodization process. Band gap states of the TiO2 were altered by controlling the anodization electrolyte composition and thermal annealing conditions that resulted in enhanced photo activity. These nanotubes were used for reducing CO2 to methanol either by photochemical or photo electrochemical routes. Pd nano-particle loaded TiO2 nanotubes were employed for photochemical reduction of CO2 to methanol that showed a conversion rate of 12 x 10-3 mol m- 2h-1. Carbon modified TiO2-xCx type nanotubes were used as photo anode and Ti as cathode for photo electrochemical reduction of CO2. The potential of Ti cathode was maintained at -0.5 V SCE. The formation rate of methanol was determined as 13 x 10-3 mol.m-2h-1.1. IntroductionGlobal warming due to emission of carbon dioxide is a serious environmental concern. The atmospheric concentration of CO2 is about 384 ppm by volume and about 3 x 1012 tonnes by weight. Burning of fossil fuels and deforestation are the leading causes for increase in the anthropogenic CO2. More than 32 x 109 tonnes of CO2 are released per year (based on 2006 data) worldwide from the fossil fuel. Pumping CO2 from the fossil fuel power plants into deep ocean basin is one of the most discussed disposal options. The other potential option is converting this green house gas into valuable fuels.Carbon dioxide feed stock can be converted into fuels of solid, liquid or gas phase by chemical, electrolytic, photocatalytic and photo-electrocatalytic methods. Reduction of CO2 to fuel form of any phase requires energy. The reduction process should be energy efficient so that we do not spend more energy and emit more (indirect) CO2 in the process of converting CO2. From this point of view, conversion processes occurring at room temperature look attractive.Electrolytic conversion of CO2 into various forms such as methane1, ethane2, ethylene3, methanol4,5, ethanol6, n-propanol, formic acid7, and formaldehyde has been widely reported. The standard equilibrium potential (at pH: 0) for reduction of CO2 to methanol is 0.14 VSHE and to methane is 0.2 VSHE which is thermodynamically more favorable than hydrogen reduction. However, the gas phase reduction is kinetically complex requiring effective electrocatalyst. The major issues with electrolytic conversion of CO2 to useful products are:"

Jan 1, 2010

By Jie Ma, Shun-Li Zhao, Jian Zhao, Jie-Yu Zhang

"Microstructural morphology evolution of Ni-45wt.%Mo droplets during rapid solidification process was investigated using an advanced modified 3D cellular automaton-finite element(CAFE) model by CALCOSOFT software. The model was modified by User-defined functions (UDFs) and validated with experimental solidification microstructural morphology of Ni-45wt.%Mo droplets available in the literature. Then, the influences of convection heat transfer coefficient, superheat of the alloy droplets and droplets size were investigated during the rapid solidification process. The predictions show that microstructural morphology is obviously sensitive to convection heat transfer coefficient and droplet size. With the decrease of convection heat transfer coefficient, the grain density decreases. In addition, the decrease of the droplet size could obtain refined microstructure. However, decrease the superheat ofNi-45wt.%Mo droplets has little effect on microstructural morphology.IntroductionFor several decades, much attention has been paid to undercooled alloy droplets of rapid solidification process for which can obtain refined microstructure, decreased microsegregation and extended solubility of alloying elements [1-3]. Extensive prior work shows that solidification of droplets plays an essential role in advanced material properties [ 4]. Consequently, it is very important to investigate the microstructural morphology evolution, especially for dendrite growth during non-equilibrium solidification process, for dendrite growth reflected the kinetics of the crystal growth process."

Jan 1, 2013

By Vincent Canaguier

Methane is increasingly considered as a promising reductant for metal oxides, including chromite. To assess the possibilities of such reduction route, the gas-solid reactions between Ar–CH4–H2 gas mixtures and synthetic chromites are studied between 950 and 1050 °C. The influence of Mg and Al additions on the reduction-caburization of (Fe,Mg)(Cr,Al)2O4 solid solution is investigated thermodynamically, structurally and kinetically. The product phases are examined by x-ray diffraction (XRD), scanning electron microscopy (SEM), and electron probe microanalysis (EPMA). The reaction rate is derived from real-time exhaust gas measurements and post-reaction product analyses such as oxygen analysis. Kinetic models are proposed based on the product phase morphologies and confronted with the empirical data.

By Lin Yang, Yuanbo Zhang, Zhuoxuan Li, Guanghui Li, Jinghua Zeng, Tao Jiang

A technique has been proposed for recovering iron from hematite-rich diasporic-type bauxite ore in this study. Direct reduction roasting followed by low intensity wet magnetic separation process was carried out. The parameters including reduction temperature and time, sodium salts, grinding conditions and magnetic field intensity for separation of iron were determined. The optimum process parameters as follows: roasting temperature of 1050 oC, time of 60 min, sodium salts involving sodium sulfate, borax, sodium carbonate with dosages of 10 wt%, 2 wt%, 35 wt% respectively, and magnetic field intensity of 1000 Gs with fineness of pulp reached 92.75% passing -0.074mm. Under the optimal conditions, an iron concentrate containing 88.17% total iron grade and iron recovery of 92.51% was obtained, 4.55% total iron grade in tailings. This novel technique provide a potential route for utilizing hematiterich diasporic bauxite ore, recovering iron resource firstly, and extracting alumina from magnetic separation tailings further.

Jan 1, 2015

By W. R. Opie

Fundamentals of blast furnace smelting of low grade copper and precious metal scrap and residues are reviewed with emphasis on emission control, by-products produced, slag cleaning for high recovery of metal values and the evolution of an off-gas system to eliminate hydrocarbons that result from decomposition of plastics in the blast furnace- charge. Problems with tin, antimony and nickel in the smelter-refining cycle are discussed.

Jan 1, 1985

By A. Warczok

The oxidation and smelting of chalcopyrite, bomite, chalcozine and pyrite has been studied under simulated flash smelting conditions. The results of copper sulphide oxidation show that under constant oxidation conditions, the degree of oxidation drops sharply when the particle size is increased above a given range. This critical size range varies typically between 200 and 500 pm depending on the oxygen content in the gas phase. For bomite, chalcopyrite and pyrite, the critical size range increases with increasing iron content in the mineral and with increasing oxygen content in the gas phase. The extreme case is observed for pyrite in pure oxygen, where there is no effect of the particle size on the degree of oxidization. Microscopical observations of the oxidized products show the influence of different factors on the mechanism of oxidation and fragmentation of the sulphide particles. Based on microscopical analysis and phase identification of the oxidized products, a model has been proposed for the oxidation and smelting of copper sulphide particles in suspended state. The mathematical model describing the sulphide particle oxidation is supported by the obtained results. Using this model, it is possible to describe the role of particular factors in the sulphide minerals oxidation.

Jan 1, 1992

By Xian-Dong Zhou, Guo-Sheng Sun, Jianzhong Luo, Hong-An Guan

"Oxygen utilization rate of the pretreatment process which adopts biological contact oxidation method for slightly polluted supply water is relatively low, less than 10%, usually lower than 3%. So the aeration amount is not determined by calculated value of oxygen demand when doing process design, but by the ratio of gas and water. The aeration way of the biological pretreatment process for slightly polluted supply water was introduced in this paper. In the foundation of the principles of mass transfer kinetic theory and experimental data, the change law of DO (dissolved oxygen) and ammonia in the aeration tank was analyzed to explore aeration method which will help to improve the overall effectiveness of handling capacity.IntroductionThere are many kinds of filler used in the biological contact oxidation process, such as flexible solid filler, composite filamentous filler, powdery clay filler, particle ceramic filler and so on. Regardless of the different forms of filler, there are a couple of common points in the function of the aeration[1,2]: (1) The aeration process in biochemical tank not only provides adequate oxygen for the biological reaction, but also plays as a role of stirring water; (2) Biochemical reactions mainly happen in the upper reaches of tank, but seldom at down-streams.This paper, from the perspective of changing aeration way, discussed the feasibility of improving the effectiveness of biochemical reactions without increasing aeration amount, which would have some leading significances for the operation and management of similar projects."

Jan 1, 2008

By Junji Shibata

Extraction behavior of Ti(IV) and other metal ions, such as Fe(III), Fe(II), Cu(II), Zn(I1) and Co(I1) from acidic solutions like sulphuric acid and hydrochloric acid was studied in order to recover titanium from the waste solution in Ti02 production. Extractant used was tri-alkyl phosphine oxide whose trade name was Cyanex 923. Then, a study was made of the idea of simulating a countercurrent multistage extraction system, using the results of batch extraction. The simulation was camed out on extraction and saipping behavior for a Ti(1V)-H$O,-Cyanex 923 system. From the simulation result., the optimum operating condition of the system was considered.

Jan 1, 1994

By John M. Boyle

The use of high vacuum mercury retort recovery as a safe and effective means of removing mercury from mercury hazardous waste solids rendering them non-hazardous and recovering mercury suitable for recycling.

Jan 1, 1995

By Yonghua Li, Fanling Meng, Weitao Zheng, Xiaodong Wang

The NiTi thin films were deposited onto copper substrates by magnetron sputtering. Tensile tests were carried out on CSS-44100 electron universal test-machine. X-ray diffraction profile Fourier analysis method has been used to study the mechanical properties of deformation NiTi thin films. The surface micrographs of the NiTi thin film were obtained using scanning electron microscopy (SEM). It has been found that the dislocation density and the deformation storage energy density increased with elongation increased. Microhardness was calculated from the dislocation data. The results showed that the microhardness values were not in a good agreement between calculated values and measured values. The oxide layer on the surface of NiTi thin film affects the measured values of microhardness. The Vickers hardness measured values are larger than the calculated values. The experimental results showed that a series of parallel cracks grew in a concerted fashion across the thin film and the cracks were equally spaced.

Jan 1, 2015

By T. T. Natarajan, Nagy EI-Kaddah

"Numerical simulation of electromagnetic confinement systems generally requires large CPU time due to the strong coupling between the electromagnetic and the free boundary problems. The present paper examines the accuracy and the computational efficiency of the most common numerical schemes used in modeling such systems. Levitation melting was taken as a test case. In this study, a comparison was made between the finite element and surface integral methods for electromagnetic field calculations. The computational efficiency of Lagrange and the modified Hestenes methods for solving the free boundary problem were investigated. The convergence of the Lagrange method was found to be much faster than the modified Hestenes method. It was also found that finite element method not only gives accurate solutions, but faster convergence to the final equilibrium shape than the surface integral method. The applications and the limitations of these techniques in modeling electromagnetic confinement systems will be discussed.IntroductionIn recent years there has been a growing interest in the use of electromagnetic forces for confinement of molten metals as a means to eliminate molten metal contamination during melting and to improve surface quality of cast products. Continuous casting of metal without contact of a mold is now a reality, and is being commercially applied for casting of aluminum slabs /1/, and copper rods /2/. New applications of electromagnetic confinement in melting and casting include containerless melting (Magnetic Suspension Melting) /3/, edge containment in twin roll casting, and meniscus shape control in continuous casting of steel /4/.Modeling of confinement systems involves the determination of the electromagnetic field and the equilibrium shape. These two problems are strongly coupled due to the dependence of the field on the shape of the melt. While significant advances have been made in computational electromagnetics /5/, the application of developed computational techniques to electromagnetic confinement problems is not a simple task. The principal difficulty in using these methods is that the solution domain is not known a priori. due to coupling between the electromagnetic field and the free boundary problems. These two problems have to be solved simultaneously, leading to an iterative solution procedure. As a result, numerical simulation of electromagnetic confinement systems are computationally intensive with computational time at least an order of magnitude larger than the fixed domain problems."

Jan 1, 1994

By Zhang Yongzhu

The metallogeneticy and mineralogy of three types of Chinese refractory gold deposits (Au-As; Au-As-MeS; Au-As-C) which are somewhat different from those abroad are discussed. The modes of occurrence, the distribution of grain size, and the morphological features of gold in minerals and their influences on gold recovery by direct cyanidation are also discussed. According to the mineralogy of gold and minerals, bacterial leaching, pressure leaching and roasting technology are suitable for the pretreatment of arsenopyrite-Au, pyrite-Au and carbonaceous-clay-Au refractory gold ores prior to cyanidation, respectively. The most important sulfide pyrite bearing much gold is difficult to be oxidized, its crystalline structure, conduct-types , and minor elements in different mineralizing stages are also discussed. The pyrite aggregates in different deposits are very complicated and much different. Gold grade of arsenopyrite is much higher than that of pyrite for some deposits which have a high correlation coefficient of Au vs As.

Jan 1, 1992

By Patrick R. Taylor

A novel method for Chemical Vapor Infiltration (CVI) using plasma technology is proposed, Plasma Enhanced CVI (PE-CVI). Due to the low rates at which CVI is currently performed, the use of plasma as a source of heat may be considered to be a faster and less expensive production method. Precursors fed in the hot region of the plasma gas are completely vaporized and forced by the same flow through a porous preform where it condenses as a new material. In this research, silica and methane where used as precursors to form SiC/on a / graphite felt (preform). To enhance the infiltration process, vacuum was used to increase the flow through the preform. Characterization of infiltrated graphite was perfontied using Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD). A uniform distribution of Sic was observed along the felt with only twenty minutes of infiltration process, yielding a 178% increment in weight.

Jan 1, 1997

By Mitsuhiro Ito

"To allow various wastes containing high levels of chlorine to be used as alternative raw materials for Portland cement, two practical methods of chlorine removal were developed. In the first method, chlorine is extracted from the wastes during the cement manufacturing process. In the second, ash-dust waste with high chlorine content is first washed and then dehydrated to cake before being introduced to the cement manufacturing process. This cake can be used as an alternative for some cement raw materials. By combining the two methods, various wastes previously considered unsuitable for recycling due to their chlorine content can often now be used in cement manufacturing plants. As such, these methods represent a major contribution to environmental protection as well as a solution to problems relating to the diffusion of heavy metals and dioxins from cement plants.1. IntroductionWaste generation levels have risen rapidly in recent years. in both the consumer and industrial sectors and today, the need for effective, efficient waste management is one of the most pressing and serious problem of today's society.The Japanese cement industry has reacted to the increase in waste generation by using certain materials as alternative raw inputs or fuels for cement production, in an effort to contribute to society and conserve energy resources.These wastes often contain non-negligible levels of chlorine and heavy metals, however, both of which are unsuitable for cement production. Depending on the element content, Heavy metals have a particularly negative effect -on cement quality; in addition, they can be released into the environment. Chlorine, on the other hand, is contained in large amounts in incinerated ash from household wastes as well as in certain plastics. Both substances are considered impediments in cement-production, not only because they reduce the quality of the cement produced but also because they impair operating safety on cement production lines.To address this problem, two practical technologies have been established for separation and recovery of chlorine components during cement pre-processing and production. This paper introduces the application of these technologies with a special focus on incinerated ash from urban wastes, a representative form of waste material having notably high concentrations of chlorine, heavy metals, and dioxins. We also outline the technologies enabling this material to be used as an alternative input to cement production."

Jan 1, 2000