Search Documents

By G. C. Yao

Branch and needle-shaped intermetallic compounds of iron, silicon and aluminum normally exist in the molten aluminum. If a suitable amount of manganese metal is added into molten aluminum, the shape of the intermallic compound particles may become lumpish and spherical. According to the difference in electric and magnetic properties of these impurity particles and molten aluminum, these impurity intermetallic compound particles can be separated by applying an alternating magnetic field. In this experiment the alternating magnetic field was formed by a "c" type loop with AC (50Hz) current. The inner vacuum of the fireclay refractory separator is 25xl5xl30mm3 with a lateral baffle inside. The separator was put into the interspace of the "c" type loop. It was found that the longer the separation time, the larger the amount transferred of impurities. The amount of transferred impurities increases with the increase of separation time and intensity of magnetic field. The addition of manganese metal enhances significantly the efficiency of impurity separation

Jan 1, 2003

By Raghavan Srinivasan, Y. V. R. K. Prasad, William G. Frazier, Steve C. Medeiros

"Aerospace gas turbine disks operate in an environment of relatively high stresses caused by centrifugal forces and elevated temperatures. These severe conditions necessitate the need for materials with good high temperature strength and low cycle fatigue resistance. One class of alloys used for this task is the nickel base superalloys, out of which, lN 718 is the most widely used in the aerospace industry [I]. The properties of IN 718 are attributed to the combined effects of the chemistry, heat treatment, and microstructure. The chemistry is tailored not only for solid solution strengthening but also for precipitation hardening developed during heat treatment, which combined with a fine grained microstructure lead to excellent mechanical properties such as low cycle fatigue resistance and elevated temperature strength. The properties of a gas turbine disk are sensitive to the microstructure, in particular the grain size, which is dependent on the processing history. The ability to precisely control the microstructural development during forging is dependent on controlling the process so that the workpiece is deformed within a ""safe"" region where no microstructural damage or flow instabilities occur. The microstructural mechanisms during deformation may themselves vary within the ""safe"" region and it is desirable to determine them within the range of parameters that are commonly used in industrial processing. The objective of this work is to establish a relationship between the grain size and the process control parameters i.e., temperature and strain rate, in the hot working of IN 178.BackgroundIN 718 belongs to a class of nickel-iron base superalloys with a face-centered cubic (FCC) austenitic matrix strengthened by precipitation of ordered intermetallic or carbide precipitates and is a nickel-rich alloy strengthened by ordered body centered tetragonal (BCT) precipitates, Y"". The alloying of nickel and iron results in the formation of the austenitic matrix, y, while the addition of chromium and molybdenum cause solid solution strengthening. Also, alloying with niobium causes precipitation of the metastable hardening constituent Y"" (Ni3(Nb,Ti)). Extended aging treatments in the temperature range 650 °C - 980 °C allow the more stable orthorhombic 8 phase (Ni3Nb) to form. Trace amounts of boron are also added to serve as grain boundary strengtheners for high temperature creep resistance. Hot deformation of IN 718 is performed between the Y"" and 8 solvus temperatures to facilitate recrystallization and to control grain growth. While deformation below the Y"" solvus (""""962°C) produces no change in grain size, deformation above the Y"" solvus but below the 8 solvus will lead to a dynamically recrystallized microstructure. The presence of the 8 precipitates will pin the grain boundaries after recrystallization and restrict grain growth so that a fine grain microstructure is obtained. Deformation above the 8 solvus ("""" 1038°C) will lead to a microstructure which has undergone grain growth during deformation."

Jan 1, 2000

By F. J. Hogan

In early 1982 Atlantic Cement Company, a wholly-owned subsidiary of Newmont Mining Corp. will come on line with a new water granulating grinding facility at Sparrows Point, Maryland to produce 800, 000 tons a year of separately ground granulated blast-furnace slag. The process and product will be unique to the United States. This paper will review some initial investigations undertaken to evaluate the cementitious properties of granulated slag. The effect of slag fineness on strength development is discussed and data is presented showing a relationship between glass content and hydraulicity and grindability of slag.

Jan 1, 1982

By N. Kanarin

A thermodynamic study is reported on the chlorination of Fe(1-x.)O, Fe2O3, Cr2O3, MgO, Mg2SiO4 with chlorine in the presence or the absence of reducing atmospheres. The reactivities of these compounds as well as that of Mg3Si2O5(OH)4 using Cl2+N2, Cl2+air, and Cl2+CO gas mixtures were studied by non isothermal thermogravimetric analysis between 20 and 1000 °C. The same solids were chlorinated in a horizontal experimental set, during two hours between 350 and 1000 °C, in reducing and oxidizing atmospheres: The chlorination products were examined by XRD and SEM, and possible reaction paths were examined. Results indicate that the carbochlorination of these solids was better than their chlorination; Furthermore, the carbochlorination was performed at lower temperatures than those of the chlorination. Finally, the reaction extent was higher in the case of carbo-chlorination of these compounds. Based on these results, a process was suggested for the selective recovery of chromium compounds from the chromite concentrate.

Jan 1, 1995

By X. J. Wu

Effects of various factors such as diaphragm materials, composition of electrolytes and current density on copper electrowinning from cupric chloride solutions was investigated. It is found that the crux of this process is to prevent the dissolution of copper by cupric ion and the formation of suspended CuCl precipitate. A process with high difference of copper concentrations between the feed solution and the spent electrolyte was selected. With this process, in which the feed solution contains 90 g/dm3 [Cu"], 3M NaC1, and 10mg/dm3 bone glue, and the spent electrolytes contains 10 g/dm3 [Cul, a very smooth and dense copper cathode can be produced with current efficiency above 93% and energy requirement less than 1.7 kwh/kg Cu at 25°C with N2 sparging. If a slightly higher energy requirement is permitted, smooth and dense copper cathodes can be produced at the current density up to 800 A/m2 with the identical solutions.

Jan 1, 1991

By Tsisana Gagnidze

A processing of technogenous wastes, which involve a gold-containing sulphide minerals, is a potential source to supplement the gold reserves. Hence, searching of ecologically safe and economically reasonable methods for processing of gold-containing technogenous wastes is a topical problem. To increase a parameters of gold extraction and to simplify a technology of the processing of above-mentioned wastes of sulphide minerals, an investigations have been carried out in the direction of the use of the method of electrochemical leaching without any preliminary processing of the mineral. It was established experimentally that an introduction of nitrogen containing organic additive into chloride solution favours to reduce a Red/Ox potential of the solution from 0,8÷1,2 V to 0,35÷0,5V, which permits to conduct the process of direct electrochemical leaching at ?soft? oxidation regimes at temperatures 20-300C C without an environmental contamination by molecular chlorine and with a high degree of a gold extraction up to 80-90%.

Jan 1, 2008

By Vladimir Mindin

Simulation of complex equilibria is usually done in the P-T-X coordinates, where "Xu is the amount of individual chemical components in the system. This approach is not productive in some very important cases: (i) investigation of "open" systems, (ii) determination of coordinates (trajectories) of mono-variant points, among others. To solve these and some other problems, we use the idea of chemical potentials of elements (CPE) of the system. A system of different coordinates axes (CPE-axes ) leads to a new strategy of simulation, observing the results of the simulation, and to efficient technology of compressing and storage the data of the simulation.

Jan 1, 1994

By Julie M. Melluish

The metallurgical response of the Point Leamington deposit has been studied. Two series of bench tests were conducted and various ore samples and flotation products were examined using image analysis techniques. The majority of sphalerite and chalcopyrite grains in this texturally complex ore were found to be smaller than 10 micrometres. Copper recoveries were low with losses mainly as fine inclusions in pyrite. Sphalerite recoveries were somewhat better due to a generally coarser habit. Gold and silver recoveries were also low and only solid solution silver was identified in the ore. The deposit shows poor economic prospects unless additional tonnage of high grade zinc ore can be delineated.

Jan 1, 1989

By Roger Altman

The solubility of copper in primary spinel crystals encountered in reverberatory slag samples has been determined by electron microprobe analysis. These spinels, which ranged in composition from 22% A12O3 to pure magnetite, contained small quantities of dissolved copper (0-0.4%). Based on literature data it was estimated that the solubility limit of copper in solid magnetite is no greater than about 1% at 1200°C and about 2% at 1250°C. However, it was found that practically every spinel crystal examined contained significant amounts of matte inclusions. Further examination of converter slag revealed large quantities of irregularly shaped precipitated magnetite crystals which contained a large proportion of copper inclusions. Additional experimentation showed that the total copper content in reverberatory slag samples was greater than the sum of the estimated en- trained plus dissolved matte in the slag. This difference is believed to be significant and is due to the presence of matte inclusions in the spinel crystals. In the present reverberatory slag samples these inclusions accounted for about 1/2 of the amount of sulfide directly entrained in the slag.

Jan 1, 1976

By Xiaobing Yang, Animesh Jha, Greg Doughty

"Successful use of inert anodes should reduce the CO2 footprint in aluminum production. The search for a “holy grail” inert anode for metal electro-winning from constituent oxides using molten salt bath as an electrolytic medium is continuing. In this article we demonstrate the engineering approaches for the fabrication of intermetallic anodes, based on a quaternary Al-Ti-Cu-M (M:Ni, Fe) system for primary aluminium production. In particular, we examine the microstructural and electrochemical properties of alloys, based on the quaternary compositions. We explain the aspects of phase stability under anodic potential, which leads to the loss of anodic materials in the temperature range of 850-1050oC. The results are analysed in the context of oxidation reaction and formation of oxide layers which readily dissolve in the cryolite melt and prevent passivation. The paper also describes the conditions under which the reduction of aluminium at the graphite cathode occurs which also strongly depends on the molten salt chemistry for the nucleation of molten aluminium at the cathode.1. IntroductionOxygen-evolving inert anodes are an alternative to the conventional consumable carbon anodes for the production of primary aluminium. In this paper the materials selection criteria chosen for the engineering of anode is based on the understanding of the thermodynamic stabilities of aluminide intermetallic phases, some of which are formed and remained stable in fluoride melts. For example, the formation Al3Ti dispersed in aluminium metal via molten-fluoride flux reaction is well known in the context of aluminium casting and grain refining [1-3]. It is for this reason in our research we concentrated on the engineering of stable intermetallic phase mixture in the Al-Ti-Cu ternary system, shown in Figure 1 [4]. In this figure two compositions in the Al3-0.5zTi1-0.5zCuz family are shown with the substitution of 7 atomic % and 11 atomic % copper. However initial investigations showed that these two compositions were unsuitable due to the formation of low-temperature liquid (~540oC) and intermetallic phase, Al2Cu along the Al-Cu binary edge during solidification. The Al2Cu phase segregated along the boundaries of Al3Ti and Al5Ti2Cu, and dissolved away when electrolysis was carried out using these anodes above 800oC. The presence of consequential porosity in the anode material increased the corrosion of the alloy through local heating due to high current density at 0.8 A cm-2. The early tests were carried out with cryolite melts, shown in Figure 2, having 3 weight percent of Al2O3 in the bath at 850oC."

Jan 1, 2010

By Patrick F. Mahoney

Each year in the United States over 10 million tons of metal are discarded with our municipal waste. This, includes, not only ferrous metals, aluminum and copper but gold, silver, platinum and every other precious metal. Resource recovery, as an approach to waste management, is replacing disposal and it presents great opportunities for those in the metal refining and recovery industry. Combustion of waste enriches the metal fraction left in the ash to the point where metals can be efficiently recovered. The recovery and quality of metals can be enhanced by good combustion control. Innovative technology is needed to efficiently tap this generous, and renewable mine.

Jan 1, 1995

By Chen Yongming

In order to eliminate the serious environmental pollution caused by low concentration of sulfur dioxide smoke in antimony smelters, a new smelting process, named as reducing-matting smelting, is proposed in this paper. The effects of technical conditions such as smelting temperature, smelting time, Pyrite cinder addition and the amount of additive on the smelting of stibnite concentrate have been investigated by the method of single-factor experiment. The results show that the optimum conditions are as follow: The amount of pyrite cinder is 1.2 times of its theoretical amount. The addition of soda and sodium sulfate is 15% and 72.6%, respectively, to the amount of stibnite concentrate when the total amount of sodium is 30%. The reducing-matting smelting is conducted at 1100°C for 2h then the smelting temperature is raised to 1200°C for 50min. Under the optimum conditions, the direct and total recovery ratio of antimony can gain 90.99% and 98.87%, respectively, and the fixed ratio of sulfur is higher than 99%.

Jan 1, 2006

By E. Açma

Sivas-Divrigi flotation plant has a capacity of 90,000 tpy. Beneficiation of the tailings of iron ore magnetic separator seems to be attractive, because of its Cu, Co, and Ni contents. In the experimental work, sulfidic flotation concentrate is produced from these tailings. A roasting-leaching-H2S precipitation procedure is used to treat this concentrate, containing 0.55% Cu, 0.51% Co, 0.74% Ni, and 0.027% Zn. Sulfatizing roasting is carried out in a rotary furnace at 690°C. Roasted product is leached with 10 gpl HzSOl at 70°C and 30% pulp density. For the precipitation of desired metal, H2S is bubbled through the concentrated solution of repeated leaching, under controlled temperature and pH. Final metal recoveries of 91% Cu, 91% Co, and 50% Ni, and 92% Zn are attained. Roasting gases with their 13% SO2 content are suitable for H2SO4 production and the leach residues can be integrated with the iron ore processing plant as they contain 57.4% Fe and very low non-ferrous metals.

Jan 1, 1993

By Y. Fukunaka, M. Niinae, E. Kusaka, T. Kuzuya, R. Ishii

"Samarium oxalattr particles was precipitated in oxalic acid aqueous solution from samarium-loaded D2EHPA solution emulsified with a conventional impeller. The calculated fractional precipitation of samarium oxalate was reasonably compared with the value determined by chemical analysis. Morphological variation of oxalate precipitate particles was then examined with H2C2O4 concentration in aqueous solution, Sm(III) and D2EHPA concentrations in organic phase. The needle-like precipitate was identified as Sm2(C2O4)3 10H2O by XRD. Precipitates obtained at higher H2C2O4· or Sm(III) concentration greatly decreased the length of major axis of precipitate, while those at higher D2EHPA concentration increased it. The oxalate was further precipitated under ultrasonic irradiation. However, the morphological variation caused by theses processing variables was not so evident under ultrasonic irradiation as in an impeller or shaking mixer.IntroductionThe materials processing of the rare earth elements must be reviewed from the scope of industrial ecology, since they have the potential applications of magnetic materials as well as secondary battery in developing programs of the electric vehicle. The technological trend to develop the electric vehicle may greatly influence the concept of materials processing, since the global· environmental problem must accommodate with the sustainable development for mankind. The recycle design must be a key issue in the materials science and engineering.Solvent extraction provides a unique separation technology -in this sense. Doyle (1)(2) reported the integrating solvent extraction with processing of advanced ceramic materials, whose chemical composition and microstructure must be precisely controlled. In her paper, the higher productivity inherent to the present process superior to hydrolyzing metal alkoxides was emphasized. Oxalic acid has been used as precipitant for rare earth purification process, since rare earth oxalate has a very small solubility in water and can be easily decomposed to oxide. It is thus suitable for precipitation stripping agent in cationic exchange type extracting system (i.e. D2EHPA, VA-10, PC-88A and so on)."

Jan 1, 2000

By Mrutyunjay Panigrahi, Takashi Nakamura, Atsushi Iizuka, Etsuro Shibata

"The production of FeTi intermetallic alloys from mixed oxide precursors using direct electrolytic reduction was studied. Fe203 and Ti02 powders were mixed in appropriate molar ratios, pressed into small pellets, and then heat treated at temperatures in the range 1000-1300°C. The pellet heat treated at 1000°C was electrolyzed in molten CaCh at 950°C, using a graphite crucible as the anode and the oxide pellet as the cathode, at a potential of 3.0 V. The products of the electrolytic reduction of (Fe,Ti) oxide were examined by XRD, SEM and EPMA. It was found mat the (Fe,Ti) oxide was reduced progressively from the outside to the inside of the pellet until the metallic state was achieved.IntroductionFast and energy-efficient technologies for materials production are essential for the sustainable development of society, and such development is supported by advanced technologies. Since the introduction of titanium and titanium alloys in the early 1950s, these materials have, in a relatively short time, become major materials for the steel, aerospace, energy, and chemical industries. Its combination of a high strength-to-weight ratio and excellent mechanical properties and corrosion resistance make titanium the best material for many critical applications [1]. Titanium alloys are now used in demanding applications such as static and rotating gas-turbine engine components. Some of the most critical and highly stressed civilian and military airframe parts are made of titanium alloys. The use of titanium has expanded in recent years to include applications in nuclear power plants, oil-refinery heat-exchangers, marine components and medical prostheses.Ferrotitanium is one of the most widespread and effective ferroalloys. It is also a well-known hydrogen-storage material and will be extensively used in the future because hydrogen is emerging as an eco-friendly energy source [2], Ferrotitanium is an alloy consisting of iron and titanium, with a minimum titanium weight content of 20% and a maximum titanium weight content of 75%, and is manufactured by reduction or melting."

Jan 1, 2012

By Caisa Samuelsson

Experimental studies in laboratory-scale equipment have been carried out to study the vaporisation from dust generated during the copper converting process. In the present work the vaporisation of Zn, Pb, As, Sb, and Bi from a dust collected in the electrostatic precipitator after the copper converter were studied. The results show that Pb, Bi and As were vaporised to a high degree from the dust at a temperature above 900°C in a gas containing N2, SO2 and a small amount of H2. The vaporisation was high for these elements also in a gas containing N2, SO2 and 02 at temperatures above 1120°C. In an earlier study, thermodynamic calculations showed that it is possible to selectively condense metals at high temperature' in a gas atmosphere generated during a copper converting process. The present study was carried out to verify the thermodynamic model. The results indicate that it should be possible for a selective condensation of Zn at high temperature. The temperature required for a selective condensation of Zn is dependent upon the gas atmosphere, e.g., the oxygen potential.

Jan 1, 1998

By Anja Pfennig, Axel Kranzmann, Phillip Zastrow

"Properties of pipe steels for CCS technology require resistance against the geothermal corrosive environment (heat, pressure, salinity of the aquifer, CO2-partial pressure). To predict the reliability of two different injection pipe steels with 13% chromium and 0.46% carbon (1.4034, X46Cr13) as well as 0.20% carbon (1.4021, X20Cr13) steel coupons were heat treated by comparable routines prior to long term corrosion experiment (60°C, 100 bar, artificial brine close to a CCS-site in the Northern German Basin, Germany). In general higher carbon content exhibits better corrosion resistance with respect to corrosion rate, amount of pits and maximum intrusion depth in the case of local corrosion. At 100 bar hardened steels with martensitic microstructure have the lowest corrosion rates with an average of 0.003 mm/a after 2000 h exposure time. At ambient pressure normalized steels show the lowest corrosion rates, indicating that the corrosion is driven by grain boundaries.IntroductionEngineering a geological on-shore saline aquifer CCS-site (CCS Carbon Capture and Storage [1-3]) corrosion of injection pipe steels may become an issue when emission gasses, e.g. from combustion processes of power plants, are compressed into deep geological layers [4-8]. Typically 42CrMo4 (1.7225, AISI 4140) is used for casing, and for injection pipe the steel X46Cr13 (1.4034, AISI 420 C) or X20Cr13 (1.4021, AISI 420 J) is used. Saline formations are the most favorable storage sites in Germany [9], because of their large potential storage volume and their common occurrence. Leakage of CO2 back into the atmosphere may be a problem in saline aquifer storage, especially around the water level within the borehole. Carbon dioxide corrosion may cause failure of pipelines and wells as known from the oil and gas industry [4,6,10,11, 12].From thermal energy production it is known, that the CO2-corrosion is sensitively dependent on alloy composition, contamination of alloy and media, environmental conditions like temperature, CO2 partial pressure, flow conditions and protective corrosion scales [6-8,13- 20]. Considering different environments, aquifer waters and pressures, the analyzed temperature regime between 40 °C to 60 °C is a critical temperature region well known for corrosion processes as shown by Pfennig et al. [21-23] and various other authors [10,24-28] (figure 1). Here a maximum around 4.7 mm/year was found for the pit intrusion depth of 13% Cr steel X46Cr13. Still this may be predicted by the rather conservative Norsok-Model used in the oil and gas industry to calculate surface corrosion rates of carbon steels [29]."

Jan 1, 2014

By Alicia E. Ares

316 L Stainless Steel samples were solidified directionally under conditions which produced the columnar to equiaxed transition. The position of the transition was located in each sample and the distance from the bottom of the ingot was measured. During solidification the distribution of temperatures were measured by means of thermocouples located strategically. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solidus fronts. Comparing the location of the transition and the values of these parameters it was found that the temperature gradient reaches negative values of as low as -13.44 "C/cm, and velocities of the fronts of around 0.1 cm/s. Also, a supercooling of 5.81°C were measured which was associated with the supercooling for the nucleation and growth of the equiaxed grains ahead of the columnar front. In addition the primary and secondary dendritic spacing was measured in both regions. The spacing was compared with the predictions from available models. The results are presented and discussed in the frame of the results obtained for other alloys

Jan 1, 2002

By Huaming Yang

Infrared materials are a special kind of material widely used in military, biological engineering and chemical industry. However, the problems associated with them such as unstable properties, high cost and a high thermal expansion coefficient seriously restrict the development and the wide application of the traditional infrared materials with the SiC or ZrSiO4 matrix. The ultrafine quartz powder is normally used to prepare the infrared materials by hot-pressing technology. The aim of the paper is to investigate the thermal expansivity, the effect of the SiO2 size and the addition of Al2O3 or Fe2O3 on the infrared emissivity of the quartz matrix of the infrared material (QMIM) in a 8-25um wavelength range. The results indicate that 89% of infrared emissivity and 0.4x 10-5/°C of thermal expansion coefficient of QMIM can be obtained. The affecting mechanism of A1203 and Fe2O3 on the infrared emissivity of QMIM were also discussed.

Jan 1, 2003

By Huaming Yang

Infrared materials are a special kind of material widely used in military, biological engineering and chemical industry. However, the problems associated with them such as unstable properties, high cost and a high thermal expansion coefficient seriously restrict the development and the wide application of the traditional infrared materials with the SiC or ZrSiO4 matrix. The ultrafine quartz powder is normally used to prepare the infrared materials by hot-pressing technology. The aim of the paper is to investigate the thermal expansivity, the effect of the SiO2 size and the addition of AI2O) or Fe2O3 on the infrared emissivity of the quartz matrix of the infrared material (QMIM) in a 8-25um wavelength range. The results indicate that 89% of infrared emissivity and 0.4x 10.5°C of thermal expansion coefficient of QMIM can be obtained. The affeeting mechanism of Al2O) and Fe2O3 on the infrared emissivity of QMIM were also discussed.

Jan 1, 2003