Search Documents

By Bowen Li

Copper vermiculite is a special nanomaterial with excellent antibacterial and antifungal performance. By means of ion exchange, copper vermiculite containing up to 5.8wt% copper was prepared. The chemical and mineralogical characterization of the material was investigated in this study based on the XRD, AAS, TEM and EDS analysis, as well as the calculation of crystalline parameters and crystal chemical formula. Cu2+ and Mg2+ have similar atom radius and same electrovalence. Correspondingly, the structure character of copper vermiculite is very close to that of standard Mg-vermiculite. Most of the CU21 may have occupied the interlayer cationic positions in the form of hydrate in vermiculite. However, some may have entered into octahedral coordinate positions. The values of au and bo of the copper vermiculite crystal cell have no obvious change compared to that of original vermiculite micropowder, but the Co value decreased slightly, which is desirable for the stabilization of the Cu2+ in copper vermiculite.

Jan 1, 2003

By Jenq-Gong Duh, Jyh-Wei Lee

"Hard chromizing process is a method for developing a surface modified coating providing wear, corrosion resistance and high temperature surface protection. Two carbon steels with 0.45 wt% and 0.95 wt% carbon contents, respectively, were chromized with pack cementation process at 950'C for 4 and 9 hours, respectively. The phase transformation and microstructure phenomena of chromized coating layer and matrix of two steels were studied with X-ray diffractometer and electron probe microanalyzer. (Cr,Fe)23C6 and (Cr,Fe)7C3 carbides and (Cr,Fe)2N1-x nitride phases were observed on the chromized surfaces. The thickness of chromized layers obeyed the parabolic rate law. The mechanism and diffusional kinetics of the chromizing process were proposed. The diffusivity of chromium in the (Cr,Fe)7C3 carbide phase was calculated using the moving boundary method.IntroductionChromizing process is one of the surface treatment technologies that can produce a chromium contained surface layer with sufficient corrosion and wear resistance on the steel matrix [1-7]. The relatively low cost and no ""line-of-sight"" restrictions are main advantages of chromizing. Adequate bonding strength of these coatings to the substrate was reported [7]. Chromizing process can be classified into soft chromizing and hard chromizing [2]. Soft chromizing is applied to steels containing less than 0.1wt% carbon through which chromium will be diffused. High temperature oxidation resistance improvement is the main purpose of soft chromizing process. On the contrary, the hard chromizing can be applied to steel containing more than 0.3wt% carbon, and very hard chromium nitride and carbide layers will be formed on the surface, which are very resistant to wear, corrosion and temperature [5-7]. In the previous studies on the Fe-Mn-Al-Cr alloy [5,7] and carbon steels [6], the thickness (X) of chromizing layers was analyzed and found the parabolic rate Jaw prevailed:"

Jan 1, 2004

By Kimio Itagaki

The distribution ratios of Ag, Pb, As, Sb and Bi for the Cu2S-FeS or Ni3S2-FeS matte / FeOx SiO2, FeOx-SiO2-CaO or FeOx-CaO slag equilibration in a MgO crucible were determined experimentally at 1523~1573K under controlled partial pressures of S2 and O2 at given PSO2 of 10.1, 50.7 and 101.3 kPa (0.1, 0.5 and 1 atm) and be observed dependency of distribution ratio on the matte grade, SO2 pressure and slag basicity were analyzed on the basis of thermodynamics,

Jan 1, 2003

By O. E. Omotoso

This study is part of an ongoing investigation to understand the mechanism of stabilization/solidification of hazardous chromium wastes in ordinary Portland cement (OPC). Tricalcium silicate (C3S*),a major component of OPC is mixed with reagent grade Cr(lll) and Cr(VI) solutions, to simulate complex cementiCr waste systems. Scanning electron microscopy (SEM) and energy disperse spectrometry (EDS) were employed to provide microstructural and chemical information. Transmission electron microscopy (TEMlEDS), apart from complimenting the SEM, was used to probe the distribution of Cr in the hydration products of C3S and to provide crystallographic information. 29Si MAS NMR (magic angle spinning - nuclear magnetic resonance) Was used to characterize the influence of Cr on the hydrated silicate structure.

Jan 1, 1995

By Takao Mori

Novel rare earth boron icosahedral compounds are investigated as potential high temperature thermoelectric materials. REB50-type compounds and REB22C2N compounds were synthesized and the thermoelectric properties measured. Seebeck coefficients in excess of 200 V/K are observed at temperatures above 1000 K for the REB50-type compounds. Strikingly, n-type behavior was observed for REB22C2N. Up to now, non-doped B12 icosahedral compounds have all been p-type. The discovery of an n-type compound is extremely important in terms of the potential development of this class of compounds as viable thermoelectric materials. Low thermal conductivities of < 0.03 W/cm/K at room temperature was observed for these rare earth boron cluster compounds.

Jan 1, 2006

By G. S. Rao

Levitated drops of Fe-18%Cr-2%C were reacted with oxygen-argon mixtures to study the reactions that occur in the AOD process, where the gases are injected into the melt and form bubbles. In the laboratory an argon-oxygen pulse, followed by pure argon, was flowed past the levitated drop to simulate the transient conditions in the gas phase as the bubbles rise in the melt. Oxide layers formed on the drops immediately when they came into contact with gas pulses containing 75% or more oxygen. Once the oxygen flow had ceased, the oxides reacted with the carbon in the drops to form CO gas and eventually disappeared. The de-carburization reaction occurred without oxide formation when the gas contained 50% oxygen or less. Melts that were sampled after EAF tapping, ready to be charged into the AOD, showed a higher tendency to oxide formation and consequent carbon boil than pure ternary Fe-18%Cr-2%C alloys made in the laboratory. The actual steel samples contained significant impurities, such as 0.25% Si and 0.56% Mn. A similar effect of oxide-forming impurities had been observed previously with binary Fe-C alloys. Movies were taken of the oxide formation and decomposition, and the results will be presented, along with data on the experimental conditions, including temperature and oxide compositions. The results are important because they give an insight into the reaction mechanisms in the AOD, which must be understood in order to improve and model the process.

Jan 1, 2006

By Charles A. Sorrell

Two red muds, two fly ashes, and several aluminosilicate minerals were subjected to direct treatment with concentrated H2SO4 at temperatures of 175°C and below. X-ray analysis showed that virtually all the sulfate reaction products remained in the solid residue because of their low solubilities in x SO Substantial portions of the Al2O3 Fe2O3TiO2, Na2O, and K2O components of the materials reacted to form water soluble sulfates, which were then removed by H2O leaching at 55°C. The solid residue after water leaching consisted largely of amorphous silica and, in lime bearing compounds, CaSO4, The reaction and leaching processes were effective in removing all or nearly all the Al2O3. Fe2O3, TiO2, Na2O, and in lime components in the fly ashes, red muds, china clay, bentonites, the nephelioe fraction of nepheline syenite, and a plaster insulating brick composed of anorthite and mullite. Reaction with potassium feldspar and petalite took place, with formation of alkali aluminum sulfates, but the reaction rates and yields were extremely low. Potassium feldspar can be heated with Na2O and x O in air at 700°C for 24 hours, or with CaO at 1000°C for 24 hours, after which the reaction product kaliophilite, nepheline, and leucite-like phases, prove to be very susceptible to H2SO4, reaction and H2O leaching, providing yields near 100% of the Al2O2 content. An alternative method of H SO treatment consists of heating the sample in a silica tube and passing H2SO4 vapor over it. Preliminary results indicate that this method can be effective in enhancing the kinetics of reaction with the Al O component of potassium feldspar and offer the possibility that formation of Al2 (SO ) Fe2(SO4)3 and TiOSO4 can be accomplished selectively by taking advantage of the fact that the upper stability limits of the respective sulfates in the presence of H2SO4 vapor will be different.

Jan 1, 1982

By James M. Fragomeni

"The mechanical behavior of an Al-Li alloy was studied and related to the extrusion processing parameters, the plastic metal flow during defonnation, the anisotropy, and the microstructure. The extrusion temperatures, strain rates, extrusion ratios, billet temperatures, and extrusion geometries were varied during processing and correlated with the microstructure and properties. The extrusion processing variables were related to the mechariicar behavior, anisotropy, and microstructure through the ZenerHollomon parameter i.e., the temperature compensated strain rate. Based on optical and electron microscopy studies it was found that regardless of the extrusion conditions, the various microstructures for the most part were unrecrystallized for both the as-extruded and the solution heat-treated conditions. Smaller grain sizes were correlated to larger Zener-Hollomon parameters. The extrusion temperature and ratio did not significantly affect the strength or ductility as did the section geometry, which had a large affect on these mechanical properties. The anisotropy of the properties varied substantially when comparing the extruded longitudinal versus transverse grain orientations.IntroductionThe extrusion process also has a substantial influence on: the microsfructure and mechanical properties of a material that is Athens, Ohio, 45701 fonned The plastic defonnation that occurs during the extrusion process alters the grain size, crystallographic texture, anisotropy, subgrain size, dislocation density and various other microstructural features. Often the material being extruded is not homogeneous, therefore variations in the microstructure and properties occur across the cross-section of the final extruded product. The mechanical properties and microstructure can also vary with length since it is hard to maintain a constant temperature throughout the extrusion process. The extrusion temperature often varies from the heat generated during the extrusion process. The demonstration material that was extruded for this .study was an aluminum alloy containing 2.6wt, % lithium and 0.09wt.% zirconium. This alloy was strengthened by heat treatment causing nucleation, growth, and coarsening of coherent metastable o' (Al3Li) precipitates in the microstructure. The ? precipitates which are a consequence 9f artificially aging the AlLi alloy, are spherical, ordered, and coherent with the aluminum matrix and impede the dislocation glide inotion during plastic defonnation. Theo particles grow homogeneously in the matrix, and have the Cu3Au (L 12)"" superlattice crystal structure. Aluminum-lithium alloys are used primarily for aerospace structural applications since they have attractive properties such as a lower density and higher elastic modulus than conventional 2XXX and 7XXX alloys."

Jan 1, 2000

By Marcelo Mourao, Adolfo Pillihuaman, Alberto Nogueira, Cyro Takano

"The self-reduction is an alternative and promising process for production of pig iron because offers decisive benefits such as enhancing the reaction kinetic with decrease in fuel consumption and C02 emissions. The self-reduction mixture of iron ore fines, carbonaceous reducer and additives for slag forming components, without agglomeration, was tested in a laboratory rotary kiln. The additives for slag were defined for presenting two different estimated liquidus temperatures (1623 Kand 1773 K) to verify the effect of these temperatures on the iron-carbon nuggets coalescence process. These mixtures were tested at 1673 and 1773 Kin an experimental rotary kiln. After reduction-melting and coalescence processes the samples were disaggregated and the iron nuggets were classified by size. It was considered that nuggets larger than 7,93mm would be a good reference for coalescence index. Low liquidus temperature slag presented 37% of this larger fraction against only 13.5% for high liquidus temperature one. The low liquidus temperature slag would facilitate contact between the particles of iron-carbon in a rotary kiln, enhancing the coalescence.IntroductionThe slag composition usually depends on the reducer ash composition, the ore gangue, the binder composition and any fluxing material [l], and the mechanism of carbon transportation in slag that contains iron oxide reducible by carbon can be explained by the oxide reduction and the metal carburization. During carbon transportation, the carburized particle is transported to slag-metal interphases by the gravity effect, being assimilated by the metallic phase [2]. When the slag's iron oxide comes in contact with the solid carbon, it is immediately reduced, forming Fe particles and CO bubbles as it is shown in the figure l(a). The Fe particles are carburized by carbon particles; they are liquefied simultaneously in the carbon-slag interphase. The Fe-C liquid particles are transported from the slag-carbon interphase to iron-slag interphase as a result of slag flow, based on the surface tension difference (Marangoni effect), figure l(b). The Fe-C liquid particles coalesce on the iron surface and the carbon is immediately diffused in the iron as it is shown in figure l(c). The reduced iron is carburized continuously by repeated sequences [3]."

Jan 1, 2013

By Beate Ina Jenssen

Ferric iron removal from the nickel electrolyte at Glencore Nikkelverk AS in Kristiansand, Norway, is achieved by precipitation of iron hydroxide followed by filtration, and it is desirable to improve filtration properties of the precipitated iron hydroxide in order to decrease the filtration time. The effect of increasing the residence time from the current 45 min to 75 min and temperature from 65 °C to 90 °C on the filtration properties of the precipitated iron hydroxide (akaganéite) was studied by simulating the industrial process conditions in a continuous reactor setup operating at steady state, using ferrous-containing process solution as feed material. It was possible to decrease the filter cake resistance by both increasing residence time and temperature, but temperature gave the most pronounced effect and reduced the filter cake resistance by one order of magnitude.

By Omid Marzoughi

In this research, both the kinetics and the mechanisms of the roasting of a sphalerite concentrate from the Bafgh mining complex in Iran were investigated. The oxidation process was performed in a muffle furnace in air and the effects of time and temperature on the degree of oxidation of the zinc sulfide sample were quantitatively studied. The experimental data were fitted to the shrinking core model. In the temperature range of 650–800 °C, the rate-controlling step was the chemical reaction between the zinc sulfide and oxygen with an activation energy of 103 kJ mol−1. On the other hand, in the temperature range of 850–950 °C, the rate-controlling step was oxygen diffusion with an activation energy of 50 kJ mol−1. Also, the roasting process was studied using thermogravimetric (TGA) and derivative thermogravimetric (DTGA) techniques.

By Wolfgang Steffes-Tun

Pyrite ore concentrate from the Meggen mine (FRG) , which contains about 0 300 400 ppm thallium, is roasted in a fluid bed furnace at 1000 -1100 C to form sulfur dioxide and ash consisting mainly of hematite. Subsequently, the sulfur dioxide is separated from the ash or dust during several steps while cooling to about 250oC. The pyrite ash fractions show decreasing grain size down to 5 pm, a pH-decrease down to 2,4 and a marked enrichment of arsenic and thallium by a factor of 12. In the final fraction, the hot electroprecipitator dust of the dump (EGR), minute crystals of thallium-containing jarosite can be detected by analytical transmission electorn microscopy (TEM). Under oxidizing, acid conditions, jarosite may be a possible "reservoir mineral" for immobilizing thallium.

Jan 1, 1989

By Nagahiro Saito, Takahiro Ishizaki, Mituhito Hirota, Akio Fuwa

"Owing to their extremely high toxicity in the environment, the dioxins have been attracting social, technical and scientific attention in recent years. The authors theoretically had predicted the thermodynamic properties of all the dioxins via quantum chemistry and statistical thermodynamics and elucidated the generation-decomposition behavior of dioxins in the equilibrium calculation· of C-H-0-Cl system. In actual combustion processes, it is said that metallic compounds have much influences on the dioxins behavior. The aim of this study is to reveal the roles of metallic compounds the generation-decomposition behavior of dioxins is revealed from the viewpoints of quantum chemistry. Especially, the catalytic effect of copper has been investigated for the reaction, 2HCl(g)--H2(g}+Cl2(g) and for the etherification reaction from precursors, which is Phenol(g) here, to dioxins. The catalytic role of Cu is shown to have much influence on the generation -decomposition of dioxins.1. IntroductionIt is well known that dioxins are very harmful not only for our health but also for that of our children and grandchildren because they are very stable substance and their reaction rates of decomposition are considerably low. On the other hands, it is not well know how dioxins are generated and decomposed; the generation-decomposition conditions and paths as well as the catalysts to decompose them'1l. The authors believe that the thermodynamic and kinetic study of dioxins is useful to find a solution to these issuers. The authors have been investigating the following problems to reveal the generation-decomposition behavior of dioxins; (a) the prediction of the thermodynamic parameters of dioxins (2), (3), (b) the generation -decomposition behavior of non-chlorinated dioxins by the thermodynamic equilibrium calculations in C-H-O system(4) and (c) the generation-decomposition behavior of dioxins by the thermodynamic equilibrium calculations in C-H-O-CI system(5). Summaries of these thermodynamic researches are as follows.(I) The thermodynamic parameters for dioxins, which had been unknown and/or inaccurate'6 l, could be predicted and are available within the scientific accuracy."

Jan 1, 2000

By Michael F. Kitto

The production of sulphuric acid at base metals smelters is predominantly an involuntary activity and now comprises approximately 17% of all-forms sulphur supply in world terms. The majority of elemental sulphur is also produced involuntarily in response to environmental regulations regarding emissions from hydrocarbon processing plants. The paper examines the points of similarity and difference in the sulphur and smelter acid markets, and reviews their interactions. The reasons for the merchant acid market collapse of 1993 are analyzed, and the prospects of a recurrence are considered.

Jan 1, 1996

By Melvin A. Jennings

Ion-exchange technology for precious metals recovery is at a turning point. Some very exciting technology has been developed in the past five years which should lead to commercialization of the process. Ion-exchange will allow not only for the recovery of gold and silver, but also will allow for the recovery of cyanide form plant tailings. This process may soon be competitive with Merrill-Crowe for silver and once this occurs, it will become the process of choice.

Jan 1, 1991

By V. V. Kutumbarao, M. T. Nimje, G. Balasubramanian

Wastes from the aluminium industry such as red mud from the alumina refinery, fly ash from the captive power plant and spent pot lining from the smelter, have been successfully converted into glass-ceramic products. The process involves addition of a small quantity of glass former along with traces of nucleating agents to aid crystallization, to a specific mixture ofred mud, fly ash and spent pot lining, followed by melting at around 1300°C and vitrification by cooling. The resultant glass is then converted into a glass- ceramic by a suitable heat treatment at around 700 - 750°C. The glass-ceramic products show excellent wear resistance, besides possessing an aesthetic appearance. The major application foreseen for such products is as decorative tiles in the building industry.

Jan 1, 2000

By Aureo D. V. Machado

An experimental study to obtain zirconia powders (ZrOz) from carboxylate zirconium solutions followed by hydrogen peroxide stripping and precipitation, has been carried out. Zirconium carboxylate was prepared by solvent extraction from a chloride aqueous phase using magnesium carboxylate as organic phase. The variables examined in the precipitation reaction were: Temperature: 25 - 90 ?C ? H202= concentration: 0.3 - 5% wt/wt - pH: 1 ? 9 Organic/Aqueous ratio (1/1) and reaction time (30 minutes) were maintained at constant levels. The optimum results (98% precipitation) were achieved at 25 °C, 5 % wt/wt H202=, and pH = 5. The precipitates were composed of large amorphous aggregates (<I00 micrometers). After calcination for 1 hour at 1000 OC, monoclinic ZrO2 with a large variation in particle size (1 -100 micrometers) was obtained.

Jan 1, 1991

By F. J. Tavera

A study on the electro kinetics of lead carbonate, silica, and alumina, in aqueous media was carried out at different pH values. The behavior of potential was determined for these species in the pH range between 3 and 12. Homocoagulation of lead carbonate in aqueous media is analyzed at its isoelectrical point. Lead carbonate heterocoagulation is analyzed with silica, alumina, and silica ? alumina mixtures at low pH values. The experimental results are considered for their possible application to treat residual water polluted with lead.

Jan 1, 2006

By L. Cifuentes

Electrodialysis (ED), i.e. a technique based on the effects of electrically charged membranes on ions in solution in an electric field, has been applied to Cu-Fe-As-Sb- H2SO4 electrolytes similar to those used in copper electrorefining and electrowinning operations. The effects of current density, time and species concentration have been studied in a batch ED cell. The technique has shown to be effective in concentrating and separating a range of ions and points to possible new methods of treating copper electrometallurgy effluents.

Jan 1, 1999

By Min Chen

A numerical simulation of the stress field of the solidified shell in the mold during continuous casting of peritectic steel slab was calculated with commercial software. The results showed that the maximal stress on wide face of the solidified shell was located at the corner and near middle of the slab, and it increased with increasing the width of slab. In addition, the stress was also influenced by operating parameters such as superheat degree, drawing speed and cooling intensity of the mold, and the maximal stress value and its position changed with these parameters. For the slab with section size of 3200mm×150mm, the proper drawing speed was around 1.2m/min, with cooling intensity of 5500L/min while the superheat degree was 15°C to 25°C in order to prevent longitudinal crack occurring during peritectic steel continuous casting.

Jan 1, 2009