Search Documents

By Liu Xiao, Lin Xiaoying, Ma Geng, Tao Yunqi

"The soft coal in China has several issues, low permeability, high gas content and prone to gas outburst, making it difficult to drill and improve its permeability. Using the rock mass loading test, the relationship of stress-strain-permeability-time of sandstone was investigated. The fracture network that communicates with coal seams to provide the pathways for gas migration can be established by drilling, hydraulic fracturing or loose blasting in the roof and floor about 5m from coal seams top and bottom. The gas migration can be summed up as ""desorption-diffusion-two levels of seepage"" for gas drainage of the quasi-protection-layer in hard coal seams, and ""desorption-two levels of diffusion-seepage"" in soft coal seams. In the quasi-protection-layer, different gas drainage techniques were used during different stages of mining. Gas drainage of the quasi-protection-layers was demonstrated at Hebi Zhongtai Mining Co., Ltd. The results showed that the technique promotes the gas seepage flow, and improves the efficiency of drainage. The influence zone of the quasi-protection-layer was 1601 m2 and the average amount of gas drainage was 328m3/d, with the maximum being 661m3/d. INTRODUCTIONGas is one of the main factors that cause disasters and influence safety production in underground coal mines (SACMS, 2009). The coal-bearing formations in China have been subjected to multiphase tectonic stress field during the period of geological evolution. Coal body was often crushed into fragmented coals and mylonitic coals under the tectonic stresses (Su and Lin, 2009). The gas permeability of coal is generally poor. So in underground, drilling and hydro-fracturing technology have been used to improve the permeability of coal, such as intensive drilling, hydraulic punching, hydraulic cutting, hydraulic extrusion and deep hole blasting. But the gas drainage rate was low, only 23% (Liu, Li, and Li, 2006; Li and Wei, 2006; Henan Polytechnic University, 2008; Ma, et al., 2014; Lin and Wu, 2009; Zhou, et al., 2011) that was much lower than the rates achieved in the main coal-producing countries such as America and Australia whose average rate of gas drainage was 50%. The protection layer mining technology has been used widely as an effective technique to improve the permeability of coal in the mining of multiple coal seams (Cheng and Yu, 2003; Diaz and Gonzalez, 2007; Karacan, et al., 2007; Palchik, 2003; Latham, et al., 2013; Yuan, et al., 2013; Shi and Liu, 2007; Wang, et al., 2008, Guo, et al., 2015; Lu, et al., 2015; Slazak, Obracaj, and Swolkien, 2014 ). In the single low permeability coal seam, there is no protection layer. This kind of coal seam has low permeability, high gas content, soft coal body, and is prone to serious gas outbursts. During drilling, the holes very often spray, collapse, stuck and wedged the drilling tool. The hole length drilled is difficult to reach the required minimum, the service life of holes for gas drainage is short, the construction cost is high, and the holes are difficult to maintain. The gas drainage efficiency of single low permeability coal seam, especially soft coal seams, cannot be improved even though hydro-fracture technology has been implemented, because its permeability is not improved."

Jan 1, 2016

By Jun Lu

This paper presents the evaluation, enhancement and comparison of two hydraulic fracturing techniques which were employed to mitigate the impact of a massive sandstone channel on two successive longwall faces. The hydraulic fracturing technique and Longwall Visual Analysis (LVA) software were initially employed to mitigate the impact of thick, massive sandstoneroof during mining of longwall Panel 21. Improved longwall face conditions and productivity were observed as Panel 21 mined through the sandstone channel. However, moderate sandstone fractures and falls at the face were still present in areas where hydraulic fracture influence was not present. Such adverse conditions caused two to three weeks of production delays due to large face cavities, jammed face conveyor and subsequent face gluing. Based on the mining experience in Panel 21, and site-specific roof geology in Panel 22, a modified and more effective hydraulic fracturing program was employed. Fewer well-placed holes were drilled, and larger volume of water was pumped into each hole in order to propagate the individual horizontal pancake fractures over a larger area, thereby enhancing caving and relieving face pressure caused by overhang of the massive sandstone. Longwall Visual Analysis (LVA) software was also employed at Panel 22 to predict the cavity risk index and guide the longwall face crew in double-pulling shields behind the shearer drum. This helped to reduce the tip-to-face distance at the critical spots along the longwall face, which helped mitigate the formation of the roof cavities and failure of massive sandstone onto the face conveyor. Underground observations, face advance rate and face rock delay analysis confirmed that longwall face conditions and advance rate in Panel 22were significantly improved compared to those of Panel 21. Consequently, safety and productivity were improved.

Jan 1, 2014

By Gregory J. Chekan

Developing a coal seam that has been influenced by previous mining in seams either above or below can result in severe ground control problems. In many instances, interactions between operations are inevitable. but improvements in ground stability can usually be achieved by-predicting potential problem areas in advance and adjusting the mining plans accordingly. This report investigates four case studies involving interactions between operations that used both room-and-pillar and longwall mining methods. In each case, geologic and mine design parameters are addressed, and those parameters found critical to the interaction are further defined in relation to observed ground problems.

Jan 1, 1990

By A. H. PH. D Wilson

Compared to the rocks encountered in, say, metalliferous mining or tunnel drivage in igneous and metamorphic rocks, the strata associated with the coal measures are relatively soft. If excavations are made at depths greater than one or two hundred metres, zones of fractured or yielded rock develop around the openings. The stress which can be taken by yielded rock at the boundary of an opening is low, but because of the friction present between the fragments or particles, the sustainable stress rises rapidly with distance from the opening until sufficient confinement has been developed to prevent failure of the rock in the first place. Thereafter the laws of elasticity will apply and increasing distance will reduce the stress field until conditions consistent with the cover load are reached. For rocks which maintain their elastic condition right to the edge of an opening, finite element analysis and similar techniques have proved successful in determining the distribution of stress around the opening. This approach, however, is not successful when a yield zone is introduced between the elastic zone and the opening. Nevertheless, some estimate is required if help is to be given in the siting of roadways and in the determination of adequate pillar sizes. This matter is of particular importance in the planning of new mines especially if retreat faces are involved, as extensive roadway drivage must be planned and executed before experience of the effects of face extraction is gained. In 1977, the author published [I] a method based on 'stress balance'. The total aggregate downward load over a large area will remain that of the cover load even after part of the coal seam has been removed. Any rise in stress in ribsides and pillars must be offset by an equivalent stress reduction across roadways and other areas of extraction, and vice versa. Knowledge of one can lead to an estimate of the other, provided the general form of the stress distribution can be postulated. It is the object of this paper to revue the method in more detail and to give further examples of its successful application.

Jan 1, 1981

By Russell Frith

The paper defines the various operational advantages associated with the use of cribless tailgates during longwall extraction and considers the associated ground control issues that need evaluating to ensure a successful outcome. Reference is made to longwall mines in Australia currently using cribless tailgates and the geotechnical and ground support factors that allow them to do so This includes the nature and behaviour of the roadway roof the stability of the chain pillar and also the type and timing of installed support A specific case history from a colliery in NSW will he referred to whereby heavy standing support was replaced with lower density tensioned cables as routine TV secondary support, which resulted in both improved TG roof conditions and a significant cost reduction. The conclusion will be drawn that cribless tailgate roadways can potentially he used in many environments either due to the existence of highly competent immediate roof conditions or through the appropriate application of active reinforcing support measures in less competent conditions. Use will he made of Strata Engineering?s roof behaviour and stability model in demonstrating the various concepts involved.

Jan 1, 2000

By André Zingano

This paper analyses possible causes for floor heaving in room-and-pillar coal mining. The coal mines are in the southern part of Brazil, where the Barro Branco Coal Seam varies in depth from 20m to 400m, and a very thick volcanic formation overlies part of the sedimentary basin. The erosion of part of the volcanic formation causes this large range of overburden thickness, which formed large V-type valleys. The mine in study is located near the slope of one of these valleys. The mine inclined shaft is at the lower overburden thickness area of the valley and the mining is developing toward the thicker overburden area. The floor heave occurred in the crosscuts, which are parallel to the slope valley direction. Numerical modeling was applied to study the stress distribution around the openings; and fieldwork on the floor heaved entries was carried out. The geometry of mining (pillar and openings width) also was analyzed. The results showed that the very weak rock and the high horizontal stress were the causes of floor heave. As the mining gets near the valley slope, the stress distribution around the crosscuts changes considerably. In addition, the stress distribution changes as the mining goes far from the crosscut. Keywords: floor failure, room and pillar, finite element model

Jan 1, 2002

By Maynard O. Serbousek

The mechanics of load transfer of fully-grouted roof bolts in coal mines has been investigated in laboratory and analytical studies. The purpose of this research is to increase the understanding and better interpret data from pull tests which are routinely performed in the field. Laboratory work includes variation of bolt length, hole diameter and grout type in pull tests. Four-foot bolts were tested in holes of 1- and 1-3/8-inch diameters. Both polyester resins and inorganic grouts were used as the anchorage medium. The bolts were strain gauged at six locations to observe the rate of load transfer from the bolt to the rock mass when a force was applied at the bolt end using standard Jack pull testing procedures and equipment. Analytical studies using closed form solutions and finite-element techniques were compared to experimental results. The models are for the elastic regime only but do include slip elements. A detailed analysis of the load transfer mechanisms from the bolts through the grout to the rock mass is presented.

Jan 1, 1984

By James Arthur

In deep coal mining the support of the underground roadway is fundamental and without knowledge of the mechanics of ground control a mine is unlikely to be operating safely and efficiently. It is therefore important for the support system to be designed sat¬isfactorily for the size of the excavation required and to do so an understanding of the behaviour of the surrounding strata is re¬quired. Over the last 15 years there has been a major change in the industry and the support systems adopted. The industry has been privatised, legislation has been updated, a comprehensive research programme has been carried out and guidance docu¬ments produced. The paper will show how privatisation has not allowed support standards to deteriorate, highlight research, the legislation and guidance documents updated and how this has led to a reduction in accidents and falls of ground..

Jan 1, 2002

By Tetsuro Esaki

This paper describes the present condition of mining-induced damages in Japan and the characteristics of them. The change of mining operation and environmental condition has caused various significant impacts on the ground environment: subsidence, cave-in, springing out of ground water etc. The characteristics and the influences of these phenomena are discussed by investigation of the actual conditions and by fundamental studies. Some counter measures are also introduced.

Jan 1, 1989

By Salah Badr

Longwall mine layouts with their entries, chain pillars, face support systems, advancing mining faces and compacting gobs represent a geomechanically complex mining operation. Geomechanical aspects are further complicated if mining occurs at depths exceeding 350 m, as stresses induced adjacent to the excavations exceed the unconfined strength of the coal and result in fracturing of the sidewalls of entries and chain pillars during development. Traditional methods of geomechanical analysis, whether empirical or numerical, are unable to represent such behavior satisfactorily. Achieving some meaningful results requires explicit representation of the three-dimensional boundary conditions and implementation of appropriate constitutive models for the rock mass. This paper describes a numerical modeling methodology for deep longwall mines operation using the FLAC3D finite difference de, which incorporates a strain softening constitutive law for modeling failure of coal. An important aspect of the modeling method includes accounting for stress relief provided to the pillars and entries due to the increasing load applied to the compacting gob.

Jan 1, 2003

By M. E. Duncan Fama

The aim of the paper was to model numerically some aspects of the extraction of coal pillars by split and fendering. A two-dimensional elasto-plastic plane strain model with strain softening and interface modelling was used. The model was able to simulate the improvement of conditions experienced in lifting from the fender, when the roof adjacent to the fender has caved. In contrast, when a stook was left, providing support to a span of uncaved roof, the model predicted the fender would suffer considerably more deformation and strain.

Jan 1, 1992

By Jingyi Cheng

Many longwall panels in China are laid out along the dip direction such that the direction of longwall retreat mining is along the strike direction of coal seams. Downward mining longwall panels in steeply inclined seams refers to those that are laid out in a non-uniformly developed fold structure where the seam is not only steeply dipping, but also highly undulated along the strike direction, causing longwall mining extremely difficult because it has to deal with large dip angles that vary both in the mining and faceline directions. Obviously, the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply dipping seams have unique patterns that are very much different from those cases of mining the flat or gently inclined coal seams. The effects of those unique patterns presented a big challenge to production and safety. Almost all previous and current researches on ground control have been concentrated on issues related to the flat and gently inclined coal seams. Conversely, research on steeply inclined coal seams, especially those with large angle variation both along the seam dip and strike directions is almost none. Therefore, it is very important to initiate a study to better understand the characteristics of mine pressure and overburden strata movement for this special type of geological condition. The objective of this paper is to monitor and analyze the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams, the angle of which varies greatly along both the seam dip and strike directions. The measured data has conclusively demonstrated that the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams are different from those for the flat and gently inclined coal seams. The large downward angles of coal seam undulation along the strike (mining) direction can obviously affect the roof movement and reduce strata pressure. Study in this research showed that appropriately increasing the rate of mining (or face advance) is positive to roof control.

Jan 1, 2013

Results of direct shear tests on rock discontinuities and triaxial compression tests on intact rocks are presented and - discussed. The main parameters considered area stress functions, angle of internal friction and cohesion variations. Primary objective of this work is to determine relationships that adequately describe the rock behaviour for design of mining excavations, while still maintaining a certain degree of simplicity.

Jan 1, 1987

By Anthony T. Iannacchione

This study, funded by the Appalachian Research Initiative for Environmental Science (ARIES), examines how mine layout, mining method, and geology interacted to allow water from the Grove No.1 mine pool to discharge into local surface waters. Federal and State regulations prohibit the discharge of acid or iron-producing waters from underground coal mines. Mining companies design barriers around their operations to prevent mine waters from discharging to the surface. The Grove No.1 represents one mine where these designs proved inadequate. Unique geologic conditions at the Grove No.1 mine pool, combined with retreat room-and-pillar mining, contributed to a discharge that required passive water treatment.

Jan 1, 2013

By Bruce Hebblewhite, Jim Galvin

"A coal burst occurred on 15 April, 2014 at the Austar Coal Mine, located west of Newcastle, NSW, Australia. The burst resulted in fatal injuries to two men working as part of the mining crew at the development face. At the time, a continuous miner was being used to mine a longwall development gate road through heavily structured coal, at a depth of approximately 550m. A number of pre-cursor bumps had occurred on previous shifts, emanating from the coal ribs of the roadway, in proximity to the coal face.This paper reviews the geological, geotechnical and mining conditions and circumstances leading up to the coal burst event; and presents and discusses the available evidence and possible interpretations relating to the geomechanical behaviour mechanisms that may have been critical factors in this incident. The paper also discusses some key technical and operational considerations of ground support systems and mining practices and strategies needed for operating in such conditions in the future.INTRODUCTIONAustar Coal Mine is an underground longwall coal mine located near Cessnock in the Hunter Valley of New South Wales (NSW), Australia and is the only underground mine still extracting the Greta Seam in this region. The mine was the first in Australia to adopt the Chinese-developed Longwall Top Coal Caving (LTCC) method for thick seam extraction. Typically seam thickness ranges from 4m to 7m and depth of mining from 480m to 560m, with future mining planned down to depths of up to 700m, making it one of the deepest operating coal mines in Australia.On 15 April 2014, a pressure burst occurred in the left hand rib at the active mining face of B Heading, 2 to 3 cut-through, Maingate A9 panel, during development of the gateroads for the ninth longwall top coal caving panel. Strata in the general vicinity was affected by disturbed geology and multiple geological structures. Figure 1 shows a section of the mine plan as at October 2014 (six months after the accident), indicating the current longwall extraction panel (AS) and the development panel A9 where the accident occurred. (Note: Neither development nor longwall face positions changed significantly between the time of the accident and the date of this plan). At the time of the accident the current longwall face was in excess of 1,000m away from the Maingate A9 development panel face position."

Jan 1, 2016

By Erdal Akyol

The rockbolting method of support is employed widely in several countries in different of mines. Hard rock mines use this method extensively. Soft rock mines, such as coal mines, have employed standing supports (steel sets) as the main method, although some countries such as the U.S.A. and Australia have preferred rockbolting. There is increasing interest in extending the rockbolting method in coal mines. The application of rockbolting techniques in an industry which traditionally has not applied such techniques, has required the development of a systematic design approach. This design approach uses extensive monitoring, to asses the viability of the support system in differing conditions. Currently at a number of new and existing mine developments in the U.K., rockbolting is being successfully applied. Although, inevitably some localised geotechnical problems have been encountered and have needed to be taken into account. The effect of faulting on roadway conditions is discussed in this paper and a design approach has been applied using a numerical analysis method, namely the Finite Element Method. The results presented in the paper serve as a useful guide to roadway support designers, and in particular the role played by different bolts in a range of conditions.

Jan 1, 1992

By Kikuo Matsui

Standing supports such as steel arches or square work supports along with the necessary struts and lagging have been traditionally employed in the longwall gateroads of the Japanese underground coal mines. Miike Colliery has newly introduced the interpanel-pillar mining system and the strata bolting system in gateroads to raise productivity levels and reduce operating costs. The Department of Mining Engineering, Kyushu University, in cooperation with the Miike Colliery and the Coal Mining Research Center, Japan (CMRCJ), has been conducting research into the optimum design of strata bolting as a primary support system in longwall gateroads. This paper presents a brief overview of the current state of strata bolting technique being applied in longwall gateroads at the Miike Colliery and discusses some problems in employing bolting.

Jan 1, 1993

By Paul Hagan

A diverse range of rockbolt designs and resin anchors are available for use in underground mines. Despite their wide spread use, the factors that affect the performance a rockbolt is not fully understood. The laboratory-scale rockbolt test facility at the UNSW Mining Research Centre is being used to gain a better understanding of the behaviour of rockbolts leading to an improvement in ground support. A test program investigated the nature of load transfer between a fully encapsulated rockbolt and the surrounding rock mass. It was found that with all other factors held constant, there were differences in the behaviour of load transfer depending on the method of loading. The typical pull-out arrangement as used in most field test work resulted in a different load transfer function to that observed when the load on the rockbolt was induced through bed separation.

Jan 1, 2004

By Hamid R. Nikraz

This paper reports the finding of a comprehensive investigation carried out to evaluate the compaction characteristics of saturated sandstone aquifers in the Collie Coal Basin under conditions anticipated during dewatering operations. A triaxial technique has been adapted to evaluate the compaction characteristics of the sandstone aquifer in the Collie Basin. This technique, which allows the strata stress regime to be reproduced by triaxial loading with zero lateral strain, also provides a precise evaluation of lateral stresses and consequently Poisson's ratio under in situ conditions. The paper contains a description of the equipment commissioned, test techniques, results, analysis and interpretation of the data obtained. The testing evaluation techniques are general in nature and can be applied to field situations in locations where similar weak sandstones occur.

Jan 1, 1993

By Kot F. v. Unrug

The depletion of thicker coal reserves has resulted in the thinner seams being economically attractive. Surface protection against subsidence limits the extraction ratio to 50% for the room and pillar method as a "no subsidence condition". That rule was developed for pillars with smaller width/height ratio because seams mined at the time were commonly 6 feet thick. Over time pillar ribs deteriorate around the pillar perimeter and thus decrease the area of the pillar. Using 50% extraction as the no subsidence condition in the squat pillar category (below 42 in with w/h > 7) causes unnecessary losses of reserves because squat pillars are stronger. In this paper a method is presented for design of long-term pillars. Based on the analysis of pillar deterioration and field observations, an increase of the "no subsidence" extraction rate to 60% for squat pillars is proposed.

Jan 1, 2001