Search Documents

By Christopher Mark

The first International Conference on Ground Control in Mining opened with the topic of pillar design. Two classic papers were presented, one by Bieniwski and the other by Wilson. Unfortunately, the two methods were so radically different from each other that it was nearly impossible to reconcile them. Adding to the confusion were the many other pillar strength formulas (such as the Salamon-Munro, the Holland-Gaddy, and the Obert-Duvall, just to name a few) that were also available. Little wonder that discussions of pillar design in those days often ended with anguished cries of ?but which formula is the right one?? The past 25 years have seen substantial progress in the science of coal pillar design. Indeed, one testament to the improvement is the relative scarcity of papers on the topic at recent Conferences. Two factors have been largely responsible for the progress that has been made. The first has been the collection of large data bases of actual case histories of pillar performance in a variety of settings, from shallow room-and-pillar mines through deep cover longwalls. These have made possible the development of empirical design procedures that are closely linked to real world experience. The second important factor is the development of sophisticated computer models that can accurately simulate pillar behavior and roof/pillar/floor interactions. Together, these two lines of research have led to a new understanding of pillar mechanics that identifies three modes of pillar failure: ? Sudden, massive collapse, accompanied by airblast, for slender pillars (width/height<4) ? Squeezing, or slow, non-violent failure, for most room and pillar applications (4<w/h<10) ? Entry failure or bumps for deep cover and longwall applications (w/h>10) It is particularly satisfying that the insights gained from numerical models broadly support those obtained from the empirical studies. While far less controversial than in the past, pillar design problems continue to arise. One recent example is pillar design for highwall mining. NIOSH has just released a software package, called ARMPS-HWM, which employs a number of modern pillar design concepts. Since highwall mining web pillars are long and slender, the greatest danger is that of a sudden collapse. ARMPS-HWM suggests two possible prevention strategies, one which concentrates on the SF of the webs, and the other which creates a ?pressure arch? using properly sized barrier pillars. The paper will close with a discussion of some current needs in coal pillar design, including: ? Updating older empirical methods, such as ALPS, where changes in technology (new types of roof support, more demanding ventilation requirements, faster retreat rates) may have made some of the original case histories obsolete. ? Methods for determining site-specific coal strengths, focusing on bedding plane strength and other factors that may effect confinement, as input for both empirical and numerical design. ? Improved methods for evaluating coal pillar performance for environmental issues, such as surface subsidence and hydrologic impacts, which consider such factors as depth, w/h ratio, water immersion/drainage, and time dependent seam strength.

Jan 1, 2006

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By Naj Aziz

The shear behaviour of reinforced rock joints is investigated for the bolt-grout-rock interaction and for failure mechanism. The effectiveness of the bolt application under lateral and axial loading conditions within surrounding materials is investigated in different medium strength. Double shearing testing of bolts were studied in concrete blocks of 20, 40, 50 and 100 MPa strengths, subjected to different pretension loads of 0, 5, 10, 20, 50 and 80 KN respectively. The experimental study was complemented with three-dimensional numerical analysis. Parameters examined include: shear resistance, shear displacement, induced strains and stresses during bolt bending process and its ultimate failure across the sheared joint planes. The conclusions drawn from the study were; the level of bolt resistance to shearing was influenced by the bolt profile configuration, the strength of the rock or medium influenced the level of load generated on the bolt, and the increase in bolt pretension has contributed to the increased shearing load of the bolted medium.

Jan 1, 2007

By D. N. Bigby

This paper concentrates on ground control innovation in Europe since the first Morgantown conference, mainly from a UK perspective. In particular, it describes the rock engineering and ground control tools developed to address the mine support and design problems associated with coal mining at great depth in areas influenced by previous workings. The differences in approach across the Western European industries are also examined. Perhaps the most significant change in the period has been in the science of coal mine rock mechanics itself, with support design now based firmly on measurement, analysis and understanding. The ground control innovations described here have played their part in increasing the efficiency with which coal is mined and in increasing safety to the extent that fall of ground accidents are now rare.

Jan 1, 2006

By J. M. Krese

This paper gives an overview of the National REAP program emphasizing the program&apos;s current status and future plans. A brief historical review of the program will be given containing roof-fall accident trends and statistics. The latest developments in roof control technology and training as it affects the REAP program will be presented. A brief discussion concerning some effects of the implementation of the amendments to Part 75, CFR, concerning roof support is included.

Jan 1, 1988

By Gabriel S. Esterhuizen

This paper addresses the need for a method to compare the effectiveness of different support systems when designing ground support in coal mines. At present, support design methods include empirical methods based on observations of past performance of installed support systems, analytical methods where the roof is typically simulated by elastic beams and numerical model analysis. The approach presented in this paper estimates the relative stability of a support design through geotechnical evaluation of the rock mass and numerical model analysis of the interaction between the rock mass and the support system. Models are used first to simulate the design performance at the expected rock conditions. The rock strength is then reduced until collapse is indicated in the model. The stability factor is then calculated as the ratio of the expected rock mass strength to the rock mass strength at the onset of collapse, and is similar to the well-known factor of safety used in engineering practice. The stability factor can be used to assist in developing a final support design by comparing the effectiveness of various support systems and the stability of excavations under various geological and loading conditions. Examples of the method?s application in three different geological settings are presented.

Jan 1, 2012

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By Thomas M. Barczak

The resultant load vector is the representation of the forces applied to a longwall roof support element by caving strata into a single, quantifiable measure of support resistance. The relatively complex kinematics of the shield support prohibit a determination of support resistance simply by summation of leg forces. A method is being investigated by the Bureau of Nines to determine the resultant load vector by instrumenting supports with pressure transducers and strain gages to measure leg, canopy capsule, and lemnisoate link forces. This concept has been laboratory tested in the Bureau&apos;s Nine Roof Simulator. Functional relationships among variables have been assessed, and confidence intervals have been established for prediction of the resultant load vector parameters.

Jan 1, 1984

By Bill Stormes

This paper will discuss implementation of the Hilti OneStep rock anchor technology to improve face bolting operations during the May 2008 longwall move; increase rock anchor installation capacity; and improve safety by reducing employee exposure periods by utilizing the Hilti OneStep rock anchors.

Jan 1, 2008

By André C. Zingano

The coal pillars in room-and-pillar mining method are subjected to vertical stress due to overburden rock mass and horizontal stress relieve due to entries excavation around them. Some coal mining companies are applying rock bolts and steel straps to improve the pillar strength, consequently to reducing the pillar size and increasing coal recovery. This kind of approach deserves some discussion, whether it is pillar reinforcement or just rib support. The efficiency of pillar reinforcement (or rib support) is directly related to the initial load capacity of coal pillar, the type of excavation, and the width to high ratio of the pillar. The objective of this paper is to understand the mechanism of pillar reinforcement (or rib support) using rock bolts and steel straps on pillar ribs. Numerical simulation taking into account the relations listed above. The results showed that the increase of coal pillar strength is very short, and there is no influence on improvement of load capacity of pillar. However, the rib support avoids block falling, rib failure, and displacement, reducing the pillar failure propagation into the pillar center. Keywords: coal, pillar reinforcement, room and pillar.

Jan 1, 2006

By Karl Zipf

In highwall mining, once a sufficient number of web pillars are developed, they can fail catastrophically in a domino-type failure, posing a safety hazard to highwall miners and sterilizing mineable reserves. Three recent case histories of catastrophic web pillar failure in U.S. and Australian mines are documented and analyzed with two design approaches. The conventional design approach uses only a strength criterion, while the postfailure design approach uses both strength and stability criteria to insure an acceptable failure mode should strength failure occur. Catastrophic highwall web pillar failures can cost money through equipment losses, production losses, coal reserve sterilization and lost opportunity costs. Coal recovery may be higher. but the benefits of higher recovery must balance the potential costs of failure. Application of the conventional or postfailure design approach will decrease coal recovery and revenues, but the risk of potentially costly failure is much less.

Jan 1, 1999

By Kieran Black

The immediate roof lithology at United Colliery is extremely variable and provides a challenge for the design of secondary support. Support design in recent longwall installation roads at the mine has been carried out using strata management techniques. These techniques allow a robust yet economical secondary roof support design to be achieved. Analysis of roof lithology and roof displacement during first pass driveage are used as a basis for the optimisation of the secondary support design prior to roadway widening. This paper will demonstrate the application of practical strata management techniques in the optimisation of secondary roof support in six installation roadways at United Colliery. The experience gained from the installation roadways for LWs 1 to 5 will be briefy discussed. The experience from LW 6 will be discussed in greater detail. The paper will describe the strata management system that was used, including mapping, borescoping and extensometry, as well as the development and application of a Trigger Action Response Plan (TARP).

Jan 1, 2007

By Andre Zingano

The coal seam strength and the failure criteria that represent the behavior of the coal seam are very important for mine section and pillar design. Additionally, mine section and pillar design take into account roof and floor layers, which form the roof-pillar-floor system. Therefore, underground ground control design begins, most importantly, with rock mass characterization. Another issue is the distribution or behavior of the coal seam strength for the whole mine area. Sometimes, the coal seam strength is assumed to be the same for an entire area, but this is not true because the coal seam is heterogenic and anisotropic, and also the coal strength is affected by faults and spacing between fractures. The objective of this paper is to demonstrate the use of the methodology for geomechanics characterization to determine the strength for the Bonito coal seam, and discuss the coal seam strength distribution around the entire mine area. The intact coal strength was determined by laboratory tests that were completed during the last 17 years, including triaxial and uniaxial strength tests. It was noted that there is a strong correlation between all laboratory strength tests with 90% confidence interval. The explanation for this coal seam strength variation is the presence of the discontinuities and their variation in quantity and quality at each location in the mine area, because the coal seam rock classification and its behavior will be affected by the quantity and quality of fractures.

Jan 1, 2014

By Shane McDonald

Australia produces approximately 84 million tonnes of coal per annum from 30 longwalls in New South Wales and Queensland, operating at an average depth of around 300m. Industry trends and expectations place increasing emphasis on the reliability of these operations; for example, the current average face width is 245m and this is expected to increase to approximately 270m by 2010. In recent years, Beltana No.1 Mine has consistently been Australia?s highest longwall producer, with ROM output of 7.2Mt in YEJ2007. Strata management has become a key feature of the operation of Australia?s longwall mines, as a tool to manage variances in the geotechnical environment. This involves an understanding of the impacts of the geotechnical environment on ground behaviour and the implications for mine design, stability and associated support, interaction and horizon selection. The anticipated ground control impacts of these factors form the assumptions that drive the format of plans specifying both triggers and actions, with quantified, monitoring-focussed experience used to refine the plan in a continuous improvement (ie ?plan-do-check-act?) process. This paper summarises the Beltana No.1 Mine strata management methodology and experience to-date.

Jan 1, 2008

By Axel Preusse

Mining subsidence plays an increasing important role in the Chinese hard coal mining. Reasons for this are a substantial rise of production during the last decade, a dense settlement in many mining regions, the increasing emergence of private residential property as well as a grown environmental awareness. German companies and research institutions hold an over more than 150 years existing know-how in all subjects of mining subsidence engineering. Due to partially comparable preconditions regarding mining depth, mining methods and geological conditions, a close co-operation between German and Chinese mining subsidence engineering experts has been in existence for some years. This German-chinese co-operation is introduced in this paper.

Jan 1, 2007

By Thomas Barczak

Roof support systems are designed for roof control to prevent unplanned falls. It sounds logical and has been the conventional thinking in support design since supports were first installed. In order to determine which support system should be used or which would be the most effective, the degree of control provided by the support system must be known. This question embodies the concept of a ground response curve, which is a measure of support control by assessment of the convergence in the mine entry as a function of the support capacity. In this National Institute for Occupational Safety and Health (NIOSH) study to optimize standing roof support design, ground response curves were developed for longwall tailgate conditions from numerical models of Pittsburgh Coal Seam geology. The models were calibrated against tailgate convergence measurements that were made in two Pittsburgh Coal Seam mines as the depth of cover varied during the panel extraction. Ground response curves were developed for four loading conditions: (1) development, (2) side abutment, (3) front abutment near the longwall face, and (4) full extraction inby the face. In general, the tailgate convergence and required support capacity increase through each of these loading stages. It was concluded that prior to failure of the rock mass, the support system regardless of its capacity has relatively little impact on tailgate convergence. Recognizing that the support cannot prevent much of the (pre-failure) convergence that is occurring is an important part of support design. Supports that exhibit high loading stiffness but cannot sustain that loading through a displacement compatible with the ground response curve will not provide adequate roof control because they can fail prematurely. The required capacity depends on the loading plus yielding characteristics of the support and the amount of rock failure that has occurred. The loading plus yielding character establishes where the support loading intersects the ground response curve. Design criterion for support capacity based on the identifying the onset of strain-soften rock response leading to ?damaged roof? is proposed as a foundation for assessing support design requirements. The capacity without accounting for the loading and yielding character of one support should not be used to assess the capacity requirement of an alternative support design, particularly when the loading and yielding characteristics are significantly different. A sensitivity study was made to evaluate the impact of mining height and overburden depth. As expected, the results show that convergence increases with increase in mining height and increase in overburden depth. Some specific support examples are also analyzed. Although this is a first step and the two-dimensional numerical models have limitations, these initial studies provide valuable insight into the control provided by the roof support system and will ultimately lead to optimizing support design based on specific mine site conditions.

Jan 1, 2008

By Andrew P. Schissler

The Citronen Zinc-Lead Project is one of the world?s largest undeveloped zinc-lead resources, containing more than 13 billion pounds of zinc and lead metal. The project is located in northern Greenland, a self-governed region of the Kingdom of Denmark (Figure 1). Citronen is the northern-most mine in the world, operating at a latitude of 83o 3? N. In excess of 67,000 meters of diamond drilling have been completed to delineate the resource. As of January 2012, the measured, indicated, and inferred reserves for the Citronen project totaled 70.8 million tonnes, consisting of 5.7% zinc + lead (3.5% zinc cut-off) (Ironbark, 2012). For the underground mine plan, room-and-pillar and long holestoping mining methods were selected. The beneficial application of structural fill was considered for increased recovery, efficient tailings disposal, and ground control. Three types of fill were compared - paste fill, cemented rock fill, and iced tailings. An environmental and economic feasibility study concluded that iced tailings was the preferred alternative provided it met the ground control requirements. The purpose of this paper is to explain the investigatory steps that led to the possibility for the use of iced tailings as structural fi

Jan 1, 2012

By John Hoelle

Coal mines in southern West Virginia, south-western Virginia and eastern Kentucky have experienced coal bumps at least since 1933. Most of the bumps have occurred due to high cover, strong roof and floor strata and stress concentrations due to the mining sequence. A longwall mine in eastern Kentucky first experienced coal bumps on the tailgate side of the longwall face in 1989. The bumps continued until 1996. The bumps were the result of: Thick overburden up to 2200 feet Strong roof and floor (strata strengths up to 25,600 psi UCS and elasticity modulus up to 4,800,000 psi Previous over-mining in places Sandstone channels Not all characteristics occurred simultaneously. The bumps produced seismic events recorded up to 4.3 (Richter scale magnitude), and damaged pillars that were up to 147 by 152 feet in size.

Jan 1, 2008

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

By Yi Luo

A longwall mining operation went under a tall, self-supporting and free-standing wireless communication transmission tower. In anticipation of that the ground subsidence process might affect the transmission tower, the mining company took a proactive approach to mitigate the expected subsidence influences. The efforts include prediction of surface subsidence process at the location of the tower, assessment of stability, structural integrity and functionality of the tower structures, and design and implementation of mitigation measures. The intension of this paper is to demonstrate the techniques that can be used to assess and mitigate the subsidence effects on tall self-supporting and free standing tower structures.

Jan 1, 2008