Search Documents

By Norman E. Breslow, John A. Montgomery, Sanford W. Horstman

Reconstruction of historical exposures to silica dust is required in an ongoing cohort mortality study of workers in the diatomaceous earth (DE) industry. However, historical data were collected using three different sampling methods. This study was conducted to derive empirical quantitative relationships from linear regression equations between the three methods: standard impinger, total mass, and respirable mass. Dust from one diatomaceous earth processing plant was sampled simultaneously by all three methods. Results from 61 clusters of the three sampling devices indicate that the phcle size distribution of the dust varies with the two parent products sampled. baghouse product and main product. The relationships between particle counts and respirable mass are: Respirable mass (mg/m3) = 0.064 (mppd) impinger count for baghouse product dust, and respirable mass (mg/m3) = 0.018 (mppcf) impinger count for main product dust. The relationships between particle counts and total mass are: Total mass (mg/m3) = 0.837 (mppcf) impinger count for baghouse product, and total mass (mg/m3) = 1.21 (mppcf) for main product dust. In all four euuations, the intercept did not differ significantly from zero, and the correlation coefficients ranged from 0.90 to 0.95. Results are compared with data from four previously published studies.

Jan 1, 1991

By Franz Deix, Bernd Braun

A sensitive portion of Section U 6/3 of the Vienna, Austria subway system required construction of two single-track tunnels under a telecommunications facility, where strict ground settlement limitations had been set. Local geology, hydrology, and site constraints led to the decision to use the New Austrian Tunneling Method (NATM) supplemented by compressed air and partial dewatering. In addition, ground freezing was used, as the tunnel would pass through alluvial layers beneath the facility, with a cover of as little as 1.5 m. Laboratory testing and two in situ test fields were used to collect frozen soil data so that the freezing scheme ensured minimal heaving magnitude.

Jan 1, 1987

By H. Lind

The consumption rate of Estonian oil shale increases due to the growing rate of exported oil-shale oil. Estonian oil shale active resources in working mines are predicted until the year of 2025 when the consumption rate stays at the level of 12 tons per year. If the consumption rate stays at that level, new mines should be opened after 20 years, if the rate increases new mines should be opened even earlier. The predicted active resources in Estonian oil shale deposits are calculated for 60 years, based on the parameters of the power station technicoeconomics. As a result, there is a need to open new mines. One of the potential areas for surface mine is the Tammiku-Kose prospect area (Rheinbaun Engineering, 1996).

Jan 1, 2006

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels relative to maintenance (service) intervals during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type of engine (technology) and its tuning, the type of work performed (as related to the engine workload), the suggested maintenance intervals, the altitude, the temperature and humidity of the atmosphere in the underground mine, the properties of the fuel and the operator's training and experience levels. The necessary ventilation quantities were calculated based on exhaust gas-concentration measurements and site-specific relationships between pollutants and adjusted air-quality indices. Diagrams comparing the necessary and recommended airflow for several equipment groups, featuring two engine types and different maintenance intervals, are presented.

Jan 1, 2000

By S. Lin, Y. J. Wang

Fan stall is a notorious phenomenon of axial flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts on the stability of the ventilation system are very complicated and not well understood. Results from laboratory experiments indicated that, when a fan is working across its stall zone (i.e., the pronounced trough on the fan characteristic curve), some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a nonachievable quantity range of the branch, because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). This paper discusses these important characteristics of ventilation systems by using results from tests on laboratory tubing networks.

Jan 1, 1998

By L. E. Krys, K. D. Harrison, C. G. Anderson

Since 1984, nitrogen-species catalyzed pressure leaching has been utilized at Sunshine Mining and Refining Company for the recovery of precious metals from a refractory sulfide concentrate. The process operates without the use of cyanide. The plant is now the only industrial-scale commercial application of this technology. Since the inception of the process, changes have been implemented to improve efficiencies and throughputs. Two of these changes, the replacement of nitric acid by sodium nitrite and a concentrate regrind, have recently been implemented. This paper discusses the development and potential mechanisms involved in these recently patented plant-process changes. A companion publication (Anderson et al., 1996) covers the plant integration and potential applicability of the technology.

Jan 1, 1997

By L. E. Krys, K. D. Harrison, S. M. Nordwick, C. G. Anderson

Since 1984, nitrogen-species catalyzed pressure leaching has been utilized at the Sunshine Mining and Refining Company for the recovery of precious metals from a refractory sulfide concentrate, The process operates without the use of cyanide. The plant is now the only industrial-scale commercial application of this technology. Since the inception of the process, changes have been implemented to improve efficiencies and throughputs. Two of these changes, the replacement of nitric acid by sodium nitrite and a concentrate regrind, have recently been implemented. This paper will discuss the outcomes of these recently patented plant-process changes. In particular, a comparison between the previously used method and the new leach method is made. Also discussed is the potential applicability of the process to other materials. A companion publication (Anderson, Harrison and Keys, 1996) indicates possible mechanisms responsible for the success of these process changes.

Jan 1, 1997

By C. Garcia, H. Arias, J. D. Miller, C. L. Lin

The question of ultimate recovery in heap leaching operations is always of particular concern with respect to economic considerations. Of course the particle size distribution is a critical factor which determines ultimate recovery and which must be established based on a balance between the extent of mineral exposure and transport phenomena. Now it seems that the ultimate recovery for a given particle size distribution can be established from mineral exposure analysis by x-ray microtomography (XMT). Using recently developed software, micro-CT data can be used to determine the fraction of mineral exposed and thus the ultimate recovery. Examples of mineral exposure analysis are given for the copper heap leaching operation at Zaldivar, Chile.

Jan 1, 2002

More than 5,300 mining professionals from around the world attended the SME Annual Meeting and Exhibit, March 1-3 in Denver, CO. Seventy three technical sessions highlighted innovative technologies and applications for the development of mineral resources. And the exhibit featured 421 companies worldwide and 632 exhibit booths. The 1999 SME Annual Meeting had 10% international attendance Professionals from outside the United States were guests at the first SME International Reception. Other meeting highlights included the Keynote Session. This pivotal session examined the international experience of North American-based companies. Speakers presented their perspectives on international explorations and operations. Keynote speakers included Robert Buchan, Chairman an( Chief Executive Officer, Kinross Gold; Dave Baker, Director Global Mining Project Management, Caterpillar; and Leendert Krol, Vice President International Operations Newmont Gold. Ihor Kunasz, 1998 SME President, made the introductory remarks.

Jan 1, 1999

By Ronald L. Haxby

This report presents a refractive seismic technique for evaluating the strength of rock within an open pit bench. A concept of correlating rock strength and seismic velocity is discussed and a method of predicting the degree of fragmentation of a pit bench is introduced, Figure 1 shows the area of interests [ ] Most of the work was performed while completing graduate studies at the University of Arizona.

Jan 1, 1967

By Richard R. Klimpel, Basil F. Fee

This paper summarizes the status of a series of new chemical reagents developed with the explicit goal of expanding the capabilities of existing froth flotation processes as well as allowing for new solid/solid separations to be undertaken that are not now feasible with flotation. The first portion of the paper briefly outlines the theory and motivation behind the development of each new reagent family. 'The second portion of the paper deals with specific laboratory examples of some separation systems studied to date.

Jan 1, 1993

By E. R. Reeves

The mining industry has recognized the importance of engineering controls as a primary means of preventing hearing loss. The noise control treatments most commonly observed on drills and bolters during this study were windshields, sound absorbing material, and hydraulic motor covers. These controls were evaluated on machines at underground metal mines to determine the amount of noise reduction achieved by each control. The results indicate that absorbing material has very little effect on the noise level. The noise reduction attributable to the motor covers was dependent on the material used to create the cover. Properly installed windshields were the most consistent control.

Jan 1, 2004

By M. J. Meulendyke

Within the mineral processing Industry. a range of grinding conditions exists which include semi-autogenous grinding (SAG), rod milling. and conventional ball milling. Each of these mill environments presents a unique environment for grinding media, requiring the application of specific physical and chemical properties for optimum grinding media performance. The environments are characterized by varying degrees and combinations of abrasive, corrosive, and impact wear. An extensive test program has been conducted to determine the extent wear rates vary between these different applications. Test results are related to production results, ball size, and mill operating conditions.

Jan 1, 1989

By E. D. Gálvez, L. A. Cisternas, A. López-Valdivieso, F. Lucay

"The floatability of molybdenite fines in saline solutions was investigated through microflotation studies using a modified Hallimond tube. In addition, the effect of pH and gypsum precipitation from calcium ions (Ca2+) and sulfate ions (SO4 2-) ions in saline water on the recovery of the molybdenite was analyzed. It was found that the floatability of molybdenite fines significantly increased with the ionic strength of the saline solutions and is independent of pH above 0.5 mol/L ionic strength. The high floatability of molybdenite in saline solutions is explained as being due to the low electrostatic repulsion between bubbles and the edges of molybdenite particles, which is exceeded by interactions due to van der Waals and hydrophobic forces. The precipitation of Ca2+ and SO4 2- ions as gypsum had a detrimental effect on the natural floatability of molybdenite because of gypsum crystal attachment on the faces of the molybdenite particles. This precipitation phenomenon may be initiated in copper–molybdenite flotation circuits that use recycled saline water, like seawater containing Ca2+ and SO4 2- ions.IntroductionWater availability is a significant factor in mining projects. Water, particularly fresh water from rivers and underground water, is becoming a scarce resource for mining operations and new projects. Under these circumstances, the use of water with high concentration of salts in flotation plants is becoming increasingly important (Cisternas and Moreno, 2014). The use of seawater has been studied as a sustainable solution for many mining companies in dry areas located near the sea. Notably, using seawater in mining operations is how mining companies in Chile have coped with the problem of water resources (Cisternas and Gálvez, 2014). In 1930, small plants in Chile used seawater to float chalcopyrite from high-copper-grade ores. In 1975, the results of tests in pilot plants for the flotation of copper minerals with seawater were reported. It was found that froth formation in seawater at pH 9.5 was suitable to make the rougher circuit work properly, even without frothers. The Cenizas mining group successfully floated chalcocite, bornite and chalcopyrite in the Las Luces plant in Taltal in Chile using seawater (Moreno et al., 2011). Minera Centinela (Antofagasta Minerals S.A. Chile) is currently processing porphyry copper ores using a seawater mixture consisting of 20 percent fresh seawater and 80 percent recycled water. Lower consumption of flotation reagents was reported in both seawater and salt water. In addition, studies performed with synthetic seawater showed that certain frothers increase the froth volume, whereas others decrease it. Additionally, the froth produced with seawater carries a high amount of gangue, and low-quality concentrates are obtained, requiring more cleaning stages."

Jan 1, 2015

By Karin Bäppler

"When considering large-scale infrastructure projects worldwide special attention has to be paid to the large diameter tunnel construction projects that were successfully completed in the Southern Hemisphere. The projects that are highlighted in this paper are large-scale infrastructure projects in the sector of transport. In focus are four road tunnel projects that were constructed in Australia and New Zealand using mechanized tunnelling technology. The tunnel boring machines (TBMs) that were reliably applied to these four major projects all exceed the bore diameter of 12 meters. These TBMs are therefore in the range of large to very large diameter TBMs. The technology used demonstrates state of the art technology with tailored tunnelling technology adapted to the specific project demands. Two Double Shielded Hard Rock TBMs (Ø 12.35 meters) were used for the construction of the Clem Jones Tunnel in Brisbane crossing beneath the Brisbane River and these two machines have been reused for the excavation of a 4.3km long two-lane highway tunnel for Legacy Way in Brisbane creating a new traffic artery towards the city centre. Two EPB Shields (Ø 12.48 meters) excavated and lined the twin-tube road tunnel for the Brisbane Airport Link. Excavation diameters in excess of 14 meters, such as the Earth Pressure Balance Shield (Ø 14.41 meters) involved in the Waterview Connection Project in New Zealand, are understood in the tunnelling industry as very large diameters. The machine is customized to the requirements and subsurface conditions of Auckland. The paper spotlights the large to very large diameter TBMs that were used and focuses on the comprehensive solutions developed by the machine manufacturer to provide a system with benefits for the contractor especially for the Waterview Project. INTRODUCTION Extensive large-scale road infrastructure projects like the ones implemented in Brisbane (Australia) and currently under construction in Auckland (New Zealand) show the tendency of today’s infrastructure construction projects. Functional infrastructures need to be put in place to cope with the demand of mobility and flexibility of people living in cities and metropolises. Impact during construction work to people or environment has to be kept as low as possible to ensure the quality of life is not disrupted."

Jan 1, 2016

By Nick Katsikaros, A H. Gray

Gold concentrates are produced at many mines by a variety of centrifugal and gravity machines, such as Knelson and Falcon concentrators, however the subsequent recovery of gold is relatively inefficient and subject to security problems. The InLine Leach Reactor (ILR) offers a new method to recover over 95% of gold in concentrates using a simple, secure leaching process. The InLine Leach Reactor is of particular benefit in treating slow or difficult leaching sulphide concentrates and its performance can be reliably predicted from simple laboratory tests. The InLine Leach Reactor is now successfully operating in two gold mines providing benefits of high gold recovery, low operating costs, high security and ease of operation.

Jan 1, 1999

By Leslie Thompson, Randy Hiebert, Marietta Canty

A paper is presented in which an innovative biological process is described for the treatment of cyanide-, metals-, and nitrate-contaminated mine process water. The technology is capable of detoxifying cyanide and nitrate and immobilizing metals in wastewater from agitation cyanide leaching as well as heap leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to detoxify cyanide and immobilize several metals from a mine process wastestream at a mine in Nevada. The demonstration was performed jointly under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered by the U.S. Department of Energy's (DOE) Western Environmental Technology Office (WETO) and the Superfund Innovative Technology Evaluation (SITE) Demonstration Program under Interagency Agreement Number DW89938513-01-0. MSE Technology Applications, Inc. (MSE) located in Butte, Montana, was the contractor responsible for conducting the project, and Pintail Systems Inc. of Aurora, Colorado, was the technology provider. The pilot-scale unit was field tested at the Echo Bay McCoy/Cove Mine southwest of Battle Mountain, Nevada. The biotreatment process was con­sidered to be very successful in detoxifying cyanide from the mine process water. The process was also determined to be very effective in removing metals. The pH was consistently neutral­ized and nitrates were successfully removed in the mine process water. As a result of conducting these pilot-scale tests, the biotreatment process was concluded to offer an innovative, cost­effective alternative for the treatment of mining wastewaters.

Jan 1, 1998

By William Tattersall

On behalf of my agency, the Mine Safety and Health Administration, I would like to add my appreciation that all of you could be here today. Previous dust symposia over the years have proved the value of close cooperation among universities, government agencies, and professional societies in advancing knowledge of dust research and development in the interest of miners and the industry. I'll just comment briefly on MSHA's part of the overall effort by all parties to control miners' exposure to respirable coal dust and other airborne dusts. As you know, our agency's congressional mandate is to do what is necessary to assure that miners will have safe and healthful workplaces. In the area of coal mine health, this has meant joining with the mining community in a continuous campaign to keep respirable dust and quartz levels below applicable standards to prevent or reduce disabling coal workers' pneumoconiosis and silicosis arising from excessive exposure to respirable quartz. Currently, our agency is processing about 120,000 coal dust samples taken by MSHA and company people during the year and about 8,000 samples taken from metal and nonmetal mining operations. Our dust program, like other MSHA programs, has benefited from increased computerization of records. The attack on CWP has had the highest priority of government and industry. The goal has been to sharply reduce social costs of suffering victims and their families as well as the associated future payments under the black lung benefits program. During the 1989 fiscal year, about 104,000 former miners received about one and a half billion dollars in benefits. Since the program began, nearly 25 billion dollars have been paid out. Much progress has been made in lowering dust levels in coal mines since the standard of two milligrams per meter of air was established in 1972. Before that time, there was a 4-to-10-percent probability of a miner developing coal workers' pneumoconiosis at typical pre-1972 exposure levels. However, under the maximum respirable dust levels allowed today, this probability has been reduced to about 1 percent. Since average dust levels are lower today, we can expect fewer miners to develop CWP in the future. Out goal continues to be elimination of both coal workers' pneumoconiosis and silicosis in both coal and nonmetal mining. In 1985, MSHA revised its coal mine quartz policy to allow mine operators to submit dust samples used in setting the quartz standard. Previously, only single MSHA samples were used. Even though less than half of the mine operators have taken advantage of this change, it has provided a larger population of samples for analysis then before. Also the policy allows operations that are on a reduced quartz standard to have the standard reviewed every six months. In underground coal mining, the job of roof bolter typically has higher than normal exposures to quartz. About 45 percent of respirable dust samples from roof bolting operations contain more than 5 percent quartz and therefore are put on a reduced quartz standard. One objective of the policy revision was to improve miners' health by follow-up monitoring, and this is being done with roof bolting jobs. MSHA studies of surface coal mining operations have provided data showing that bulldozer operators and highwall rotary drill operators often have high exposure to quartz dust, and our agency is directing enforcement efforts to reducing this hazard. One of the most important responsibilities of MSHA's metal and nonmetal mine health division is the respirable dust sampling program. In the last few years, nearly 3 out of 10 samples have

Jan 1, 1991

By D. Bizier, B. H. Gardner, Y. P. Wang, S. Serata

As part of an ongoing effort to develop more cost-effective and “user friendly” hardware for geomechanical measurements required for underground mine design, Serata Geomechanics, Inc. (SGI) has investigated the potential of borehole pressure cells (WCs) for in situ measurement of stress states and continuous monitoring of changes in ground stress. In particular, because of certain advantages gained thereby, WCs utilizing an elastomer, instead of metal (e.g., copper), for the skin of the pressure cell have been developed. A data analysis technique for determining ground stress state directly from BPC data has been developed. This technique has been tested for salt ground through both in situ applications and computer simulation analysis of the BPC/borehole boundary interaction. This paper discusses the data analysis technique, the results of field and computer simulation testing of its validity, and evaluates the advantages of elastomeric BPCs in relation thereto. It utilizes field data from recent elastomeric BPC applications in the salt mine at Goderich, Ontario operated by the Sifto Division of Damtarn Inc.

Jan 1, 1986

By H. A. Kortmann

Blast furnace operators have been steadily increasing their quality requirements on burden material. These requirements include a high reduction rate of the ore burden as well as good strength at the beginning and during the whole blast furnace operation. Special requirements are made on the softening and melting behavior which ensures an optimal formation of the cohesive zone in the blast furnace. On the whole, the self-fluxed and olivine-based pellets meet these higher requirements due to their chemical composition, especially in the pure pellet operation. In the mixed sinter/pellet operation partly-fluxed and acid iron ore pellets can be appropriately used. The paper describes the demands on, and characteristics of, different kinds of pellets used in the Federal Republic of Germany.

Jan 1, 1989