Search Documents

By Antoon W. van der Vooren, Colin R. Phillips

A comparison of analytical models used to describe deposition in the first generation of lung bifurcations is presented. In order to allow testing of the mathematical models, experimental data were obtained from radon daughter deposition in simplified lung bifurcations. The experimental data for particles deposited by diffusional mechanisms is best described by the assumption of a thin concentration boundary layer at the entrance of a right circular tube. Other more complex models do not accurately describe the deposition of submicron particles. The angle of bifurcation was found to have a minor effect on deposition.

Jan 1, 1981

By Ümit Yasar Onder, Tevfik Prof. Dr. Güyagüler

This paper describes the results of an investigation done to determine thermal properties and heat emission of coal measure rocks in Karadon district of Zonguldak Coal Colliery. In Karadon District, depth of working level is about -600 m where the heat problem arises. In the near future, workings will be at deeper levels and working conditions will be more difficult due to high heat emission. At the beginning of the paper the importance of wall rock heat emission in underground mine have been explained and then the amount of heat emission to the ventilating air has been calculated. It has been found out that the strata is the main source of heat in the mine. Therefore, geothermal gradient of the region has also been determined simply by measuring the virgin rock temperatures in different levels of the mine. All other data directly related with heat emission from different sources has been collected and has been analyzed by using a special computer package. As a conclusion, total heat and moisture content in ventilating air and heat balance has been determined for Karadon Coal Mine. In addition, some recommendations and suggestions have been made for the future works when the mine workings go to the deeper levels.

Jan 1, 1995

By M. E. Kuchta

Research is currently being conducted at the Colorado School of Mines in the use of high-pressure water for scaling down loose rocks in underground mine openings. In addition to improved miner safety, the adhesion strength of shotcrete applied to rock surfaces treated with high-pressure water is also increased significantly, resulting in improved overall support capabilities of the shotcrete layer. Test results show an increase in adhesion strength by a factor of four on a concrete test wall cleaned with water at 21 MPa (3,000 psi) as compared to a surface cleaned at 0.7 MPa (100 psi).

Jan 1, 2003

By R. L. Jones, D. D. Runnels, D. P. Dupon, D. J. Cline

To establish meaningful remediation goals and monitoring programs in areas disturbed by mining and associated industries, it is desirable to determine the natural concentrations of metals that existed in these areas prior to being disturbed. In mineralized areas, multiple natural populations of metals and associated components may be present. This paper describes a method for characterizing the natural background chemistry by means of probability distribution dia¬grams. The method can be applied to water, soil and other natural materials. In a study of a complicated hydrogeologic system at the Kennecott Utah Copper North and South Operational Areas near Salt Lake City, UT, probability distribution diagrams were used to differentiate between natural background waters and waters impacted by human activities. The probability distribution diagrams allowed a component-by-¬component interpretation of the chemistry of ground¬water and surface water over a large geographic area. Natural chemical background populations and anthro¬pogenic effects were identified Although the method is illustrated for mining-related sites, the same approach can also be used for other natural and anthropogeni¬cally impacted sites.

Jan 1, 1999

By David A. Roberts, Edward J. Cording, James W. Mahar, Robert A. Robinson, Noppadol Phienweja, Harvey W. Parker

Horizontal inclinometer and deflectometer casings were used to measure deformations up to 15.2 m (50 ft) ahead of and adjacent to the heading in highly fractured and sheared shales at the Stillwater Tunnel. The measurements were compared with borehole extensometer and tape extensometer deformations to evaluate ground movements in advance of, adjacent to, and behind an advancing tunnel heading. Ground deformations of up to 127 mm (5 in.) occurred during passage of the innovative "walking blade-gripper" TBM. Deformations were compared with curvometer/distometer and vibrating wire strain gage data from steel ribs to assess rock-support interaction.

Jan 1, 1985

By H. Nakazawa, A. S. Malicsi, K. J. Reid, P. J. Ryan, I. Iwasaki, P. W. Weiblen

Precious metals are commonly believed to be recovered along with sulfide minerals in flotation, but a few neutron activation analyses showed that the recoveries of gold and silver were unexpectedly low. Reasons for low recoveries of platinum group metals remained unresolved due to interferences in the analyses. Electron microprobe, scanning electron microscope, and scanning Auger microprobe analyses have identified nickel arsenide minerals in the ore and confirmed a close association of platinum group metals with the arsenide minerals as minute inclusions. These results indicated a need for re-evaluation of flotation procedures that have so far ignored special problems related to arsenide minerals. The electrochemical and flotation behaviors of nickel arsenide and their application to the flotation recoveries of precious metals from copper-nickel bearing Duluth gabbro are presented.

Jan 1, 1987

By Sidney M. Cohen

This paper describes an economical method of upgrading a clay deposit using conventional separation processes into a suitable cement plant feed. The natural size difference of clay and silica in the clay deposit is utilized in the dry air classification device. A case study in which the raw material from a clay deposit is converted into a portland cement plant feed is presented.

Jan 1, 1983

By Stanislaw Nawrat, Waclaw Dziurzynski

An increasing concentration of coal production, especially in the circumstances of intensive methane inflow makes the coal mine managing staff apply new techniques of safe mining. It paves also the way for scientists to develop new directions of investigations and implementation of state-of -the- art technical solutions. Simultaneously, it could be noticed that the funds assigned for expansive 'En situ ' investigation are continuously decreasing. Better and better results are reached when applying computer technique in calculations of the parameters of ventilation process. Recent theoretical and experimental investigations of air and gas (methane) flow in longwall areas with caving, combined with the implementation of methane drainage system allowed to create, a mathematical model and consequently to elaborate a computer supported numerical simulation of discussed phenomena. The mathematical model has been modified and the simulation program was prepared in such a way that the software is convenient for a user looking for an optimal solution. The paper presented the methodology of optimal choice of following parameters: - ventilation system - rate of flow through the wall. The procedure takes into consideration keeping a safe level of concentration methane in air flowing through the longwall as well as the criterion of maximum methane concentration within the methane drainage pipe line. Results of variant computer simulation regarding the longwall with caving are shown in graphs and tables.

Jan 1, 1995

By Jianmin Qin, R. V. Ramani

The major parameters affecting dust flow at a longwall face are dust generation rate, air velocity and quantity distribution at the face, and the characteristics of the dust such as particle size distribution, density etc. Previous studies have identified the longwall shearer as the major source of the airborne dust in the faces. In this study, the effects of dust generation rate and shearer speed on the levels of ambient dust concentration are investigated. A series of experiments were performed under controlled conditions in a full scale simulated longwall face at the Lake Lynn Laboratory mine of U.S. Bureau of Mines using characterized bituminous coal dust. A trickle-duster was moved up and down the longwall face to simulate the shearer. In each experiment, a known amount of dust was dispersed by the trickle-duster into the air and the average dust generation rate was calculated. At the same time, gravimetric respirable and total airborne dust samples were collected and air velocity measurements were made along the face. The experimental conditions, data, and results are presented and discussed in this paper. The airborne dust concentration and air velocity data indicate that the concentration increases and air velocity decreases with distance from headgate for the first half of the face. Towards the tailgate, the air velocity increases with increasing distance but the dust concentration levels off with some variations. The data show that a higher dust generation rate results in higher dust concentration levels. More importantly, the data show that the rate of increase of airborne dust concentration is higher than that of dust generation rate. For the same air velocity distribution and dust generation rate, lower speed of the dust source results in higher airborne dust levels at the face.

Jan 1, 1991

By William H. Pomroy, Annie M. Carigiet

This U.S. Bureau of Mines report is an analysis of underground coal mine fire incidents occurring in the United States during the 15 years from 1978 through 1992. The fire data used in this analysis were obtained from Federal Mine Safety and Health Administration (MSHA) mine fire investigation reports. Fires were analyzed by year, state, coal bed thickness, mining method, evacuation measures taken, ignition source, burning substance, location, equipment involved, detection method, time of day, number of injuries and fatalities, and method of extinguishment. In all, 164 fires are reported, or an average of 10.8fires per year. The most common ignition source was electricity, the most common burning substance was coal, the most frequent fire location was the belt entry, belt conveyors were the most common equipment involved in fires, and water was the most common extinguishing agent.

Jan 1, 1995

By Eleanor Kentish, Nathan Bond, Edward Batty, Simon Webber, Alan Skarda

"Crossrail is Europe’s largest construction project — a new 100km rail route running through central London. A joint venture of BAM, Ferrovial and Kier (BFK) has constructed the tunnels and escalator shafts at the new Bond Street and Farringdon Stations. The recent trend in the UK industry towards sprayed secondary linings is driven by the potential for significant savings in cost and time. BFK is unique within Crossrail by constructing both sprayed and cast secondary linings. This paper presents a direct comparison between sprayed and traditional cast in situ secondary linings at Bond Street and Farringdon Crossrail Stations. An objective comparison is drawn between procurement and mobilisation periods, production rates, flexibility, tolerances and logistics in the tunnels. The technical challenges surrounding cast and sprayed secondary linings are explored, and recommendations are made of how each method could be improved for future use. INTRODUCTION It is well established that sprayed concrete offers a fast and effective method to seal the face of an excavation. In a relatively short space of time, sprayed concrete can be applied to an open face to support the short term ground loading on the tunnels during construction. Advances in sprayed concrete lining (SCL) technology — such as the use of wet mix processes, improved accelerators, fiber reinforcement, remotely controlled spraying robots, innovative surveying equipment and nozzleman competency schemes — have greatly increased the speed and safety of tunnel excavations using this technique. As a result, design engineers have become increasingly confident to use SCL primary linings as part of the permanent structural lining (Su 2014). Historically, long term ground and water pressure loads have been considered to be carried by the main structural or secondary lining, constructed using cast in situ concrete (Pickett 2014). However, the advances described above have made sprayed secondary linings a viable option, which has already been proven on the A3 Hindhead Tunnel (Arnold 2012). Sprayed concrete secondary linings offer potentially significant savings in cost and time during the construction process. The contractor does not need to procure a bespoke formwork system for each different sized tunnel — the SCL plant required is already on site for the primary lining. Each bay is sprayed with accelerated concrete, becoming self-supporting almost immediately — compared to moving and resetting the shutter, pumping concrete and waiting for it to cure. With sprayed concrete, working sequences and cross sections can easily be changed."

Jan 1, 2016

By Zhenqi Cai, Mike Lichte, Kimberly Kennedy

The Ohio River Tunnel is the first of three combined sewer overflow tunnels to be constructed under Allegheny County Sanitary Authority's Clean Water Plan. The project consists of a total of approximately 5.5 miles of 18-ft and 14-ft finished diameter, segmentally lined deep rock tunnels and smaller diameter dewater and flow connector tunnels, as well as 8 deep flow drop and access shafts varying from 25-ft to 70-ft in finished diameter and 130-ft to 170-ft in depth. This paper describes the project components and the primary engineering challenges faced during design, including tunnel alignments and shaft site optimization with tight right-of-way constraints and multiple railroad and highway crossings. Assessment of tunneling methodology as well as tunnel and shaft designs and constructability included overcoming 5-bar hydrostatic pressure, abrasive bedrock, and the selection of the appropriate support of excavation systems in high-permeability alluvial soils adjacent to the Ohio River.

Jun 23, 2024

By Y. Nan

A new computer simulation model for the analysis of underground coal mine production systems in the Peoples Republic of China is presented. As a case study the model was used to analyse the railway system of an existing underground coal mine. Some results of this first application are given in this paper and some conclusions of common interest for underground rail haulage systems are discussed.

Jan 1, 1986

By Liu Hanzhao, Jin Yongduo

Many gold ores which are not only submicroscopic but also rich in arsenic and organic carbon, for example Dongbeizhai Mine, have been found in china. These ores belong to the most refractory ores The key to the recovery of gold from these ores is preoxidation. Dongbeizhai ores have been tested with biooxidation, chlorination, double oxidation, acidic and alkaline pressure oxidation, catalytic oxidation, NITROX and roasting. To date it appears that either roasting or pressure oxidation is optimal. It is suggested that the flotation-roasting (or pressure oxidation)-CIL process should be used to treat this type of ore.

Jan 1, 1995

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, A. E. Clark, R. P. Bush, L. E. Schultze

The U.S. Bureau of Mines conducted copper exchange capacity (CuEC) tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the CuEC as a function of Cu concentration, pH, and temperature. Further testing resulted in regression equations expressing CuEC's of Na and Ca montmorillonites and attapulgite as a function of Cu concentration, pH, and the concentration of metal ions which compete with Cu for exchange sites. Using these equations, an analysis was made of the impact each clay could have on overall copper recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of copper from in situ leaching solutions. Copper losses are decreased by the presence of competing ions, and A1 and Mg have the largest impact of those ions normally present in Cu leaching solutions.

Jan 1, 1993

By K. S. Shivakumar, R. Bhima Rao, M. R. Patil

Liberation size can be estimated using various techniques such as grain counting, frequency curves, X-ray intensity and the mesh of grind. The present investigation deals with the estimation of the liberation size of graphite flake contained in a schistose ore from Shivaganga, India. It was observed that the flakes are liberated at from 75 to 150µm. The rougher flotation concentrate obtained after grinding the run-of-mine ore for 5 min contained 54% fixed carbon. This represented the first stage of liberation. After regrinding to <90 µm in the presence of sodium silicate and guar gum, a cleaner concentrate containing 82% fixed carbon was obtained.

Jan 1, 1998

By R. H. Grau

The National Institute for Occupational Safety and Health&apos;s Pittsburgh Research Laboratory is now involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration&apos;s compliance dust-sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels and the controls being used. A summary of the mining operations, sampling procedures, resulting data and suggested methods to improve dust control are provided.

Jan 1, 2003

By H. L. Ehrlich

Modes of microbial attack of metal carbonates, metal silicates, metal oxides and metal sulfides are summarized. The current status of microbial redox mechanisms, whereby metals in metal oxides and sulfides are mobilized, is discussed. Opposing theories of a single mode of attack involving interaction with a microbially produced reductant or oxidant in the bulk phase and of dual modes of attack involving a reaction requiring physical contact between microbe and mineral surface on the one hand and microbial production of a reductant or oxidant in the bulk phase that reacts with the mineral on the other hand are considered. No one mode when finally completely unraveled should be expected to fit all cases. Some biochemical, electronmicroscopic and spectrophotometric approaches for elucidation of missing details of different modes are suggested. Key words: Bioleaching, Biobeneficiation, Metal mobilization

Jan 1, 2003

By A. Marabini, G. Belardi, N. Sheau, F. Veglio

The present paper deals with the modelling of a Multi-gravity separator in the treatment of chromite fines. A first screening study was carried out by 2" full-factorial experiments in order to check the main effects and interactions among the investigated factors: shake frequency, shake amplitude, tilt angle and washwater flowrate were taken in consideration in the study. Two size fractions were employed in the experimental tests. Successively, considering the factor with larger influence on the Cr203 and SiO2 grade and Cr203 recovery in the concentrate, a further improvement of the experimental design was performed to determine empirical models to describe the behaviour of the MGS in the mineral treatment. The results show how intrinsic interaction among the factors take place, highlighting that an optimization study must be carried out considering all the MGS setting parameters.

Jan 1, 1995

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

Jan 1, 2007