Search Documents

By John K. Hollmann

The use of the direct method of determining coal methane content has grown in the last decade from a research technique into a practical coal exploration tool. However, the literature available on the subject is somewhat lacking in site-specific guidance and observations on the conduct of the method and the use of the resulting data. This study discusses some practical lessons learned in conducting a large scale direct measurement project at an operating mine, describes the initia1 interpretations and uses of data from the project, and presents observations from subsequent mine operations into the success and limitations of using direct measurement data in mine planning. The site studied is in central Pennsylvania on the Appalachian Plateau and includes coal seams in the Allegheny series.

Jan 1, 1987

By A. Haghighat

A risk analysis on mine fires for all U.S. underground coal mines from 2000–2012 was completed to identify locations that have a high risk for fire incidents. The data for this analysis was extracted from the Mine Safety and Health Administration’s (MSHA) mine fire accident reports database. After identifying fire incidents from this database, a risk matrix was developed for underground locations that showed a significant propensity for fire incidents. This matrix associates the hazards and risks with the severity and frequency of their consequences at each location. These significant mine areas will be the concentration of future studies in fire behavior, suppression techniques, and simulation methodologies. INTRODUCTION Fires in underground mines pose significant hazards to personnel because of inherent restrictions to movement and limitations to egress routes. Despite improvements, mine fires remain serious hazards in underground coal mine. In order to better mitigate the risks from fire hazards in the modern underground mining environment, a better understanding of where fire events occur must be gained. The following paper presents an investigation on the number of fatal and non-fatal incidents in underground coal mines fires from 2000 to 2012. Three phases of risk assessment (i.e., risk identification, estimation, and evaluation) were applied to the recorded fire events from the MSHA incident database that occurred during this time period. Using this process, a fire hazard was first defined. This definition was then used to identify any incidents that had occurred as a result of the defined hazards. The seriousness of the injuries and damages were finally quantified for each incident though an estimate of severity and frequency and then aggregated according to underground location (ISO, 1999; Van Duijne, 2008). Using this approach, locations prone to incidents resulting from fire hazards were first identified. The risk for the occurrence a fire incident in general was then estimated for each of the identified locations. The results of this assessment will be used to improve fire simulation techniques for the identified, high risk underground locations. RISK IDENTIFICATION A risk for this assessment was defined as any single occurrence of a fire initiated by the ignition of gas, dust, or electricity. Each recorded occurrence of such an event in the MSHA incident database was counted as a single fire incident. Both non-fatal incidents that were reportable but did not result in a fatality and fatal incidents that fell into the aforementioned criteria were counted. Incidents in the MSHA database that were already classified as “generic” were not considered. The remaining incidents were then totaled and aggregated according to the underground location in which they occurred. In previous studies, a number of locations, which are listed in Table 1, were highlighted as high fire hazard areas (McDonald et al, 1980; Pomroy et al, 1995; De Rosa, 2004). These locations were used to group the fire incidents extracted from the MSHA incident database. The compiled numbers of non-fatal and fatal underground coal fire incidents from 2000 to 2012 are displayed in Table 1.

Jan 1, 2019

By Thomas W. Traylor

Today, in Detroit, Michigan, a 14 ft. 6 in. diameter soft ground tunnel is being mined at penetration rates limited only by the logistics of liner handling and spoil removal. Soil conditions are highly variable and include clays ranging from very plastic to very hard, gravels, sands, silts and boulders. The permeable soils contain high concentrations of methane gas, compressed by groundwater levels some 40 ft. above tunnel invert. Despite these adverse conditions, mining crews frequently complete their 70 ft. production quota in six hours and go home. In one 4000 ft. reach of tunnel, progress averaged 68.9 ft. per mining shift. This paper has been written to explain this extraordinary accomplishment, and to demonstrate that truly continuous rapid excavation in difficult grounds is now limited by factors other than the excavation process itself. BACKGROUND The Detroit metropolitan area has a long and interesting history of soft ground tunneling. From 1949 to 1968 the city of Detroit alone constructed some 75 miles of soft ground tunnel. During this period the development and common usage of rotary or "wheel-type" soft ground tunneling machines was pioneered in the Detroit area. These machines are designed for, and were successful in, the cohesive or clayed soils that predominate the downtown Detroit geology.

Jan 1, 1997

By Clayton Vernon Deutsch, Marcel Antônio Arcari Bassani, João Felipe Coimbra Leite Costa, Vanessa Cerqueira Koppe, Pedro Henrique Alves Campos

Traditional linear approaches oversimplify the complexities of ore blending. Adopting nonlinear blending models in mining and mineral processing is critical to enhancing prediction accuracy and allowing optimization regarding nonadditive variables, such as metallurgical recovery. This study implements a simulated annealing algorithm in short-term mine planning that seeks to optimize the metal recovery by considering how to blend the ore in the mine better. Two nonlinear metallurgical recovery models are used as inputs to the algorithm to represent synergistic and antagonistic blending. The results of the case study demonstrate that the optimized schedule exhibits improvements in both blending behaviors when contrasted with conventional linear-based scheduling plans.

Jan 1, 2025

By M. Karmis

The Virginia Center for Coal and Energy Research is leading an interdisciplinary coalition to identify potential carbon sequestration sinks in unmineable coalseams as part of the U.S. Southeast Regional Carbon Sequestration Partnership. The Virginia Center for Coal and Energy Research and the Eastern Coal Council are leading education efforts for the project, as well as specific outreach efforts in Central Appalachia in order to develop a process for stakeholder education and engagement in sustainable energy.

Jan 1, 2007

By I. Iwasaki

Rest potential, cyclic voltammetry and chronopotentiometry measurements were made to study the effects of cathodic polarization of chalcopyrite, simulating the mineral contacted with grinding media under a nitrogen atmosphere. The reaction products on the chalcopyrite surface were identified by XPS, and the mechanism of the cathodic reaction was proposed. Microflotation tests were performed to investigate the effects of surface changes on the floatability of chalcopyrite.

Jan 1, 1993

By Ronald K. Frobel, Christopher J. Wienecke

Geomembrane systems and associated geosynthetics such as geotextiles, geonets, geogrids and geocomposites have been used in precious metal heap leach and tailings facilities for many years. Geomembranes have been used in the heap leach process in pad design and solution recovery ponds as well as associated collection channels as the primary liquid barrier to contain and collect metal bearing leach solution. Geomembrane systems offer an effective, low cost alternative to other containment methods such as compacted low permeability soils, asphalt or concrete. In the 19BO's, rigid High Density Polyethylene (HOPE) liners were used to a great extent with a gradual transition to the use of the more flexible Very Low Density Polyethylene (VLDPE) and Polyvinyl Chloride (PVC). These three geomembrane systems have been used successfully in precious metal heap leach solution containment. Predominant material thicknesses have been 30 and 40 mil for PVC, 40 and 60 mil for HOPE and VLDPE. Variants in recent years have included roughened HDPE and VLDPE to provide higher surface friction characteristics, as well as newer polymer materials such as polypropylene. In addition to providing an economical method for providing enhanced solution recovery, geomernbranes are also providing the primary liquid barrier for prevention of groundwater contamination. Because heap leach solution chemical components and dissolved metal constituents are classified as toxic substances, they are subject to environmental regulation. Many regulatory agencies are still developing guidelines for heap leach pad design, however a geomernbrane liner system is often used as a single liner or in conjunction with other materials to form composite double or even triple lined systems. "Other" materials can include alternate layers of drainage aggregate, geotextiles, clay layers and other geomembrane or geocomposite layers.

Jan 1, 1993

By W. Blake, J. Mahaut, W. Hustrulid

Division II at Kamoto mine in Kolwezi, Zaire represents a transition zone between Divisions I and III where transverse and longitudinal cut-and-fill rooms were being mined. Because this transition zone had been geologically depicted as being badly faulted the mining in this division had been deferred to a future time. However, to increase production and to reduce mining costs by carrying out the mining of the 3 divisions simultaneously, it was decided to mine Division II. The mining research group of Gecamines was given the task of designing a mining geometry then testing this design in a full scale test. Based on an evaluation of the faulting and fracturing of the 2 parallel orebodies and on an extensive in situ testing program preliminary mathematical analyses were used to develop and evaluate room and pillar designs in the 35°-65° dipping bedded formations. Based on these analyses and the constraints of having to fit the design of Division II to grade into Divisions I and III in a logical manner, a mining geometry for Division II evolved. To test this design an instrumented room was excavated in the most critical area. The results of this full scale testing showed that the behavior of the roof and wall rocks were as had been predicted by finite element computer model studies which incorporated the material properties and results of the field testing. The room geometry design was both judged and observed to be stable, hence mining commenced.

Jan 1, 1977

By Ross W. Smith, Xiapeng Zheng, Merrill P. Allen

The results of flotation of a primary desliming hydrosizer overflow material containing 14.6 wt.% P20, and 3.6 wt.% MgO are presented. The phosphate minerals were collophane and francolite and all minerals appeared to be liberated. The material had not been previously treated with flotation reagents. In the experimentation, various collectors were evaluated for effectiveness. The relative effectiveness of flotation in different flotation devices was determined. Finally a two-stage flotation scheme is proposed using column flotation of dolomite in the first stage and Denver cell flotation in the second.

Jan 1, 2002

By Lourens Scheepers

Mining induced seismicity and rockbursts have been part of the deep level gold mining industry in South Africa for many years. One could be forgiven for thinking that we should know everything there is to know by now to have rockbursting under control to a level that it has minimal impact on safety and production. Well, we don’t… There are things we know that we know, and they are implemented, or should be. There are thigs we know that we don’t know, and they are researched, or should be. There are things we don’t know that we don’t know, and, well, we don’t know… We know that seismicity and the associated potential for rockbursts generally increase with an increase in stress (increase in mining depth and/or mining span and creation of remnants) and proximity to faults and dykes. We know there are a number of potential sources of events in a mine; that is: mining abutments, pillar abutments, mining faces and geological structures (faults and dykes). We know there are a number of event mechanisms associated with these sources; that is: slip on a geological structure, shear through intact rock and bursting of the rock near the edge of a mining excavation. One of the tools used more and more and with increased success to identify event source mechanisms is Moment-Tensor analysis (MT). This typically assist in differentiating between three event mechanism components: volumetric deformation component, axial deformation component and slip / shear component. The insight gained from MT assist greatly in identifying the most likely event source to assist in understanding the rockmass response to mining. We know that the seismic response in our mines are mining induced (not natural). This may seem trivial, but it is important to realise that we influence the seismic response with the way we mine, and by how much we mine (extraction ratio). Therefore we put design rules and strategies in place to reduce the seismic hazard and we install rockburst support in our mining excavations. We know the seismic response to mining is influenced by the properties of the rockmass, including strength, stiffness and brittleness, but quantifying its influence is typically more difficult than expected. We know numerical modelling can improve the engineer’s understanding of the potential rockmass response associated with designed mining layouts and strategies. For our environment (narrow, tabular large area) elastic boundary element modelling remains the most convenient and practical approach, but it overestimates the stress at mining abutments and underestimates the stress further away from these abutments. Adding a crushing (based in limit equilibrium) modelling approach vastly improves the boundary element modelling ability to simulate the deformed (interpret fractured) zones and associated redistribution of stress. We don’t know how to quantify what an acceptable seismic risk is. We don’t know if we can mine remnants at an acceptable seismic risk. Some remnants are extracted surprisingly easy, others serve us with devastating rockbursts. The limit equilibrium modelling shows potential to significantly improve our ability to quantify the rockburst risk. We don’t know if large-scale preconditioning is possible and will be effective to significantly reduce the seismic risk associated with remnant and pillar mining. Research is required (and has been initiated). Vast areas of ground have been extracted historically in the South African gold fields. Most gold reserves are now in deeper ground (4000 m) and historic remnants (areas left before due to mining difficulties) as well as pillars (regional stability pillars). If we cannot find ways to extract these reserves at acceptable risk levels, the future of the South African gold mining industry is very short.

Apr 26, 2022

By R. H. Clarke

"INTRODUCTION Characterization of waste rock is frequently an oversight in mine planning which can contribute to significant delay in permitting and ultimately development. Thorough waste rock characterization is now a prerequisite to developing operating and closure plans acceptable to regulators and the public. BACKGROUND A long history of mine development has placed virtually all focus on the economic extraction and beneficiation of ore materials, while waste rock characterization and management received substantially less attention and consideration. Inadequate waste rock characterization has contributed to planning and management practices that are having unintended and unforeseen impacts to surface and groundwater, and in some cases lead to significant long term closure liability. In response, the regulatory community has developed guidelines for performing waste rock characterization during the pre- mine permitting process that in some cases seem onerous (BLM, 2013). Additionally, where a project proponent has not met these guidelines or results have been deemed “inadequate”, the Nevada Division of Environmental Protection and Bureau of Land Management (regulatory agencies) will only issue operating permits with rigid management practices to address the uncertainty, including requirements for lining waste rock facilities. WASTE ROCK CHARACTERIZATION FOR NEVADA PROJECTS Newmont Mining Corporation (Newmont) operations in Nevada approaches waste rock characterization like ore characterization, as it requires a similar investment of time, funding and attention to detail in order to pass public and regulatory scrutiny. Newmont follows a tiered approach to characterization that creates three over-lapping data sets representing an “escalation” in analysis at each tier, an approach that has thus far gained regulatory approval. “Tier 1” waste rock characterization for most Newmont projects begins with exploration drilling which follows internal standards and procedures. 20-foot composite samples are prepared from all drilling and analyzed for multiple trace elements using inductively coupled plasma mass spectrometry (ICP-MS) methods and for acid-base characterization using method ASTM-E1915. If the exploration program is successful and further resource or reserve development is recommended, the Tier 1 data are used to prepare a Waste Rock Characterization Plan (Plan) that will be presented to regulatory agencies as a part of baseline project characterization."

Jan 1, 2015

By H. T. Mikkelsen

Mineral production implies emissions of particulate matter (dust), noise and vibration that may cause conflicts with neighbors living nearby. In Norway a few conflicts has been brought to court, the latest in 2006. This paper discusses dust emissions and dust depositions (dustfall). The pollution authorities have accepted monitoring of dustfall instead of suspended dust as the first step in conflict cases concerning small and medium sized enterprises. In the case of exceeded limit values, the second step is to require monitoring of suspended dust and next the implementation of control actions to reduce dust emissions. Dustfall monitoring programmes carried out at six mineral production plants in Norway, show that the mineralogical rates of dustfall are rather low a few hundred meters away from the plants or the tailings disposal. They are mostly considerable lower than the limit value of 5 g/m²/30days accepted by the authorities. Seasonal variations between mineralogical and organic dust fractions can be observed in Norway, with higher content of mineral dust during winter time. Other sources to mineralogical dust can be recognized. During winter time wear of road pavement and sand on icy roads can give high emissions of mineralogical dust to the ambient air. Parallel monitoring of suspended dust and rates of dustfall indicate that dustfall can be used to estimate the level of suspended dust. A model for estimating suspended dust based on records of dustfall is presented.

Jan 1, 2007

By C. Anderson, K. Nikkhah

This paper outlines the role of simulation software in design and operation of a typical metallurgical plant with mineral processing and hydrometallurgical units, to produce concentrate and pure metal. It addresses the role of simulation and mass balance software in the conceptual, feasibility and detailed design stages. It discusses the use of JKSimMet for sizing of mineral processing units, and METSIM and IDEAS for development of energy and mass balances. In detailed design of a plant, the complex interaction and variation in performance of various units makes it difficult to predict overall system performance and availability. Simulation is used to: assess operating strategies that affect surge capacities at various stages compare different ore types and mining strategies that affect concentrate product quality. optimize transportation logistics for raw materials, concentrate and metal products

Jan 1, 2001

By D. Zaharaki

The present experimental study underlines the advantages of factorial design in environmental, geotechnical and waste management experimentation. A typical case study regarding solidification of metallurgical wastes is presented and the main effects and interactions of three main factors are determined in order to establish the optimum experimental conditions in terms of compressive strength. Finally, a regression equation that predicts accurately the real compressive strength of a specimen under various experimental conditions is derived.

Jan 1, 2005

By J. Gawler

In June 2005 the Minerals Council of Australia signed a Memorandum of Understanding (MoU) with the Australian Government which states an intention ?for mining companies and government to work together with Indigenous people to build sustainable, prosperous communities in which individuals can create and take up social, employment and business opportunities in mining regions?. Implementation of the MoU has begun with demonstration sites established across Australia. All sites are using a Regional Partnership Agreement (RPA) model as a framework for enabling local people to find local solutions to local issues in partnership with mining companies, governments and Indigenous communities. Mining and resources companies can provide important input into regional economic development and capacity building by working through local partnerships. Company benefits include gaining a social licence to operate, access to a reliable skilled workforce, better longterm relationships with Indigenous communities and sustainable regional communities. All levels of government, Australian, State and Local, are working collaboratively to address unemployment and other issues in remote Indigenous communities. The Australian Government has adopted RPAs as one mechanism for implementing its whole-of-government approach to Indigenous affairs. This leading edge work is unique to Australia and the model has applications and significant learning for other countries and industries.

Jan 1, 2007

By S. K. Vidyarthi

Most wastewater clean-up processes suffer from a fundamental lack of specificity in that a Reverse Osmosis process removes all dissolved solids, an Electrodialysis Reversal process removes all ions, wanted or unwanted, etc. Most techniques require the use of a membrane or contact surfaces that are prone to foul-up and are ineffective in situations where solids may be present. A photochemical process for the metallurgical industry on the other hand has the ability to operate specifically on targets that can range from one selected ion to an entire group of homologous species such as all biologically active species. Processes can be designed to change the oxidation states of a target altering the environmental impact. Several processes are currently in operation ranging from Cyanide removal to disposal of radiation wastes. This paper describes applicable photochemical processes with the help of certain key model examples.

Jan 1, 1988

By James Barker, Jacques Renault, Chris McKee

Previous XRD work by us (McKee, Renault, Barker; 199Oa, 1990b) showed that by using pressed powder briquettes and a peak deconvolution technique, quartz in perlite can be routinely determined at <0.1 wt. %. In the present report, we discuss two additional methods of standardization: 1) chemical determination of quartz in silicate standards and 2) addition of a large amount of quartz to an unknown mixture. The first method applies the concept of mass balance and is sensitive to the analysis of silica and a monitor element. The second minimizes mixing errors; its equation is non-linear and is derived from the two component case with unequal mass absorption coefficients treated by Klug and Alexander (1974).

Jan 1, 1991

By Peter Halbach

Cobalt-rich ferromanganese crusts are one type of the two oxidic metallic mineral resources in the deep ocean that incorporate metals supplied and transported from both land (aerosols, continental run-off) and sea sources (oxygen-minimum zone, hydrothermal alteration of the oceanic crust). The substances directly precipitate from cold seawater under more or less oxic conditions and form thin layers (2 up to 25 cm thick) on hard substrate rocks like volcanic hyaloclastites, weathered basaltic rocks and/or carbonate-fluorapatite; in the crusts many metals therefore exist in the highest state of oxidation. Deposits of the Co-rich ferromanganese crusts are found throughout the global oceans on the flanks, terraces and summits of seamounts and submerged volcanic mountain ranges and platforms, where the ocean currents have kept the seafloor more or less free of sediment for millions of years. The process of hydrogenetic precipitation is basically an inorganic colloidal-chemical and surface-chemical mechanism. Elements in seawater may occur as dissolved hydrated ions or as inorganic as well as organic complexes which in general have either a positive or a negative surface charge depending on the pH of the respective aqueous environment. Those complexes may form hydrated colloids that interact with each other and with other dissolved hydrous metal ions. Hydrated cations such as Co, Ni, Zn, Sn are, for example, attracted by the negatively charged surfaces of colloidal hydrous Mn-oxide particles, whereas hydrated anions (e.g. oxyanions) and elements forming larger complexes with low-charge densities (e.g. U, As, Th, Hf, REE) are attracted by the slightly positively charged hydrous Fe oxihydroxide particles.

Jan 1, 2008

The declining grades of surface deposits have re-confirmed the need for greater production rates. Large scale production requires increased investments in expensive and sophisticated equipment. The key to successful operations can depend entirely on proper equipment utilisation and in this program of research at the Department of Mining and Metallurgical Engineering, University of Queensland, much emphasis has been placed on the analysis and improvement of this aspect of a load-haul-dump operation. For a model to be successfully integrated into a mine engineering function and readily accepted by mine operating personnel, it has to offer more than just results. The concepts used in its design and construction must include sufficient detail to enable engineers to apply it usefully and with confidence.

Jan 1, 1979

By Barbara Maren Winkler

For mine production problems in mines with varying qualities, both open pit and underground, the linear programming method (LP) has been used successfully. By this method it is possible to keep the total production blend for each period within a required range of qualities while optimizing objectives like production costs, net return, ore grades, other qualities, or a combination of these. Technical restrictions like constrained capacities can be added to the model. This makes LP a flexible and powerful tool for mine production planning. Practical experiences have shown the major influence fix costs have on the actual economic result of a planning decision. It can be proven that fix costs cannot be included in LP models. We describe a way to address this fix cost problem by using mixed integer linear programming (MILP) as an extension to LP in the optimization of a mine planning problem. This raises the issue of complexity. We discuss the computational complexity of the resulting models and the enhancement of model flexibility for the user of a planning system. We demonstrate the method embedded in a practicable everyday planning system for a complex underground coal mine. By computational examples we show how the method improves the economical results of the planning.

Jan 1, 1996