Search Documents

By Pierre Mousset-Jones, Felipe Calizaya, Malcolm J. McPherson

The objective of this study is to provide potential users of booster fans in coal mines with the necessary information on monitoring and control of fans and environmental factors. The guide-lines listed in this paper were formulated based on the current practice of mine monitoring, the U.S. Code of Federal Regulations on environmental monitoring, and the United Kingdom's National Coal Board recommendations on the use of booster fans. The principles involved in the design of booster fans as well as the provisions needed to guarantee a safe operation of these units, are illustrated by means of an example problem. The example includes a summary of costs for two ventilation systems: a conventional surface fan system and a fully automated booster fan alternative. A comparison of these costs showed that significant gains may be attained by selecting a combined surface-booster fan strategy over a conventional surface fan alternative.

Jan 1, 1989

Coal fly ash and flue gas desulfurization (FGD) sludges can be returned to mine pits, fills and revegetation zones in Virginia by regulation if (and only if) a positive beneficial use can be shown. Utilization of alkaline fly ash for control of acid drainage from pyritic coal processing waste piles, and use as a soil amendment for revegetation, are the two dominant beneficial uses proposed over time. Both applications must be controlled by the basic chemical properties of the ash proposed for utilization. Currently, public concerns over long-term As and Se leaching from various applications are increasingly driving regulatory options for mine site utilization. Many fly ash materials are relatively low in inherent alkalinity or neutralizing ability, and certain ashes are actually acidic. Failure to add sufficient total alkalinity will result in strong acidification of the ash utilization zones, stripping heavy metals like Mn, Zn and Cu from the fly ash matrix. Similarly, if alkaline ash is loaded into non-acid forming coal wastes at high rates such that leachate pH is > 9.5, significant leaching of As and Se has been documented in large scale laboratory leaching columns. Utilization of fly ash and FGD as a mine soil amendment for revegetation is based upon combined liming and water holding capacity benefits, however, levels of soluble salts (primarily sulfate and borates) limit one-time application rates to 100 Mg/ha or less.

Jan 1, 2006

By Jerry L. Hodgson

This paper presents an application case history of the planning methods used for developing, costing and scheduling an underground hydro- electric pumped storage facility in weak rock. This method covers the system configuration, excavation methods and costs, initial support systems and final lining systems. This study was performed by the Omaha District, Corps of Engineers for the proposed Gregory County Hydro- electric Pumped Storage Project, and presents a synopsis and the results of the studies performed.

Jan 1, 1986

By Dirk van Zyl, Lysa Morishita

Mining companies are increasingly approaching the social aspect of sustainable development within the rural communities that neighbour their projects and operations. Rural community engagement requires significant effort and resources, and it can be extremely challenging for mining companies to earn and sustain social capital. The focus on rural, proximal community engagement is not to be understated and has led to significant benefits in many communities. However, opposition to mining projects is often exhibited in urban environments, where there may be potential for mining companies to gain social capital with relative ease. Cities tend to have existing frameworks for community engagement and public activation, such as annual parades and festivals, that make it easy for a mining company to provide financial support or value-in-kind. Local organizations and community groups can achieve the same amount of engagement in an urban environment with significantly less effort required from the mining company. By applying simple marketing principles to community engagement strategies, corporations can increase awareness for their business and encourage city residents to think critically about the origin of resources. Unlike many corporations, mining companies are not marketing or selling products to individual consumers. From this arises the opportunity for a company to use marketing to promote other positive initiatives and, as such, connect their brand with positive messaging thus earning social capital. This may lead to a wide variety of secondary impacts including benefits to recruitment efforts, increased political support, and positive media coverage. This paper explores these matters with special reference to Vancouver, BC, Canada and the mining companies Teck and Goldcorp.

Jan 1, 2017

By P. K. Ackerman, F. F. Aplan, G. H. Harris, R. R. Klimpel

Fourteen reagents that are potentially capable of chelating with a metal ion on the surface of the major copper sulfide minerals and pyrite were evaluated for their effectiveness in floating these sulfides. The reagents studied fall into the classes of mercaptobenzole mutations, thiouronium, thionocarbamates, thiourea, imidazole mutations, oximes, hydroxyquinoline and xanthogen formate. The best overall copper sulfide collector was an imidazoline (1-Hydoxyethyl - 2-Heptadecenyl), but it also proved to be an excellent collector for pyrite. Its potency as a pyrite collector can be reduced by structural alteration, but at some loss in its collecting power for the copper sulfides. The effectiveness of many of these potential collectors can be changed by minor alterations to the collector molecule and, to a lesser extent, by pH adjustment. The general order of mineral floatability with these reagents is chalcopyrite = chalcocite > covellite =bornite >> pyrite. The flotation of malachite is generally similar to that of the copper sulfides, indicating the special effectiveness of copper in the crystal lattice for collector attachment.

Jan 1, 2000

By Winfield G. Wright, Philip L. Verplanck, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

The upper Animas River watershed is affected by metal-rich drainage from abandoned mines and by natural weathering of mineralized bedrock. To investigate the importance of natural metal sources, surface waters were sampled in a minimally mined but intensely altered area of the watershed. Water chemistry was strongly controlled by the degree of bedrock alteration. Propylitically altered rocks, which contain calcite, produced neutral waters with low metal concentrations, whereas quartz-sericite-pyrite alteration was characterized by acid-sulfate type waters with high metal concentrations. A mass-balance approach was used to estimate natural metal sources, which accounted for 56-905 of the dissolved metal load discharging from the study area

Jan 1, 2000

By Lawrence A. Taylor

The rocks and minerals of the moon will be included among the raw materials used to construct a lunar base. The lunar regolith, the fragmental material present on the surface of the Moon, is composed mostly of disaggregated rocks and minerals, but also includes glassy fragments fused together by meteorite impacts. The finer fraction (i.e., < lcm) of the regolith, the soil, is probably the most important portion of the regolith for use at a lunar base. For example, soil can be used in bulk as insulation against cosmic rays, for lunar ceramic and abodes, or for growing plants. However, beneficiation of the soil can provide other feedstocks. For example, the soil contains abundant solar-wind implanted elements, as we1 1 as various minerals, particularly oxide phases, which are of potential economic importance. These components of the soil are sources of oxygen and hydrogen for water and rocket fuel, helium for nuclear energy, and metals such as Fe, Ni, Al, Si, and Ti. The uses of the lunar materials only await a fertile imagination.

Jan 1, 1990

By A. S. Malicsi, Vathsala Rajagopal, I. Iwasaki

Corrosion and abrasion properties of a series of chromium-containing, cast-iron balls, with Cr contents ranging from 0% to 29%, were evaluated and compared with austenitic stainless-steel and mild-steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite, with either 5% pyrrhotite or 5% chalcopyrite, under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynantic polarization curves under abrasion. Flotation recoveries were determined on a 95% quartzite + 5% pyrrhotite sample ground with various cast-iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with flotation results and with corrosive wear data obtained from marked ball wear tests.

Jan 1, 1993

By R. Hogg, T. F. Dumm, L. G. Austin

The applicability of SEM/EDS techniques to particle-by-particle analysis of respirable coal dust is evaluated. It is demonstrated that the correction procedures needed to account for the failure of most EDS systems to detect light elements (especially carbon) become unreliable for particles in the respirable size range (< 10 µm). Other serious limitations arise from x-ray counting errors for coal particles with low but significant mineral content and particle counting errors for liberated mineral matter.

Jan 1, 1991

By Sergio Estebanez, Martha Gross, Ruben Rubal, Yvonnick Rescamps, Alexandre Cochennec

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in coastal Virginia, USA will add two 1.5-mile (2.4 km) TBM bored tunnels alongside two existing immersed-tube tunnels between artificial islands. The site’s unusual constraints and the requirements of a large-diameter variable-density TBM shaped the design-builder’s decisions for handling TBM inputs and outputs, siting the TBM plant and supporting equipment, and sequencing tunnel-construction operations. This paper addresses the logistics necessary to enable key functions of the 46-ft (14-m) TBM and its ancillary equipment, including transport of most materials by barge, U-turn of the TBM on an artificial island, and delivery of materials for the second tunnel through the first one while interior structures are under construction.

Jun 13, 2021

By F. Calizaya, I. Duckworth

An ore-pass is an underground conduit used to transfer ore from one level of a mine to another. This method of transportation depends on the elevation energy only; therefore, it has very low operating cost. However, two inherent problems may hamper this process: (1) hang-ups of interlocked pieces and (2) a sudden release of trapped air from the ore-pass (belching). These events can create unsafe conditions with the potential for catastrophic consequences. This paper presents a summary of CFD modeling studies that were formulated to investigate the pressure build-up and belching of dust and rock particles from long ore-passes. The models were calibrated against field data collected from an actual ore-pass system and used to predict the airflow-pressure distributions in the mine for various ore feed rates and ore-pass geometries. P.T. Freeport Indonesia’s Grasberg ore-pass system (240,000 tpd capacity) was used for this purpose. This system comprises of four active ore-passes, with each being more than 600 m in vertical length.

Jan 1, 2004

By Richard Kolada

If the emission of methane into any particular area of an underground coal mine remains constant, then the calculation of ventilation requirements is relatively simple. This is also true if the ventilation system is recirculatory. However, the emission of methane into a working area can vary considerably. There is always a risk that the ventilation will not be able to dilute the emission of methane to acceptable levels, because there are often short-lived peaks of emission which are very large. The ventilation design must therefore consider what is an acceptable level of risks and calculate the airflow requirements to meet this level. The acceptable level of risk can be calculated by examining the historical variation in methane emission into the area to be ventilated. For example, consider that an acceptable level occurs when methane emission peaks only exceed the capability of the ventilation one day in twenty. Then, from the history of methane emission, it is possible to calculate the necessary ventilation requirements. This method has been used since the early 1980s for conventionally ventilated districts. This paper examines the application of this technique to districts ventilated by recirculatory ventilation.

Jan 1, 1987

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application, for geological structures, has been criticized, for its reliance on subjective interpretations. The Mine Safety & Health Administration&apos;s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and. fault zones that were parallel with projected lineaments. The Roof Control Division&apos;s successful identification o f lineaments associated with roof falls and high wall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions would allow mine operators to obviate safety concerns that might otherwise adversely affect the health and safety of miners.

Jan 1, 2003

By P. V. R. Bhaskar Sarma, P. K. Sahoo, G. Roy Chaudhury

A process was developed to treat an ammoniacal leach liquor containing zinc using Di (2-ethyl hexyl) phosphoric acid (D2EHPA) as the extractant. The objective of this work was to develop a process package for the treatment of complex sulfide leach liquors. Zinc extraction could not be carried out directly from the ammoniacal solution in mixer-settler units because of crud formation and low extraction efficiency. After neutralizing the free ammonia with H2SO4, the extraction efficiency was only about 40%, due to the high concentration of (NH4)2SO4. To decrease the (NH4)2SO4 concentration, the free NH3 was steam stripped, and the resultant liquor was subjected to zinc solvent extraction. An extraction efficiency of 98% could be achieved by controlling the equilibrium pH. Stripping studies were also optimized after removing ammonia from the zinc-loaded organic. A continuous 100-hr operation that included extraction, scrubbing and stripping, was carried out successfully.

Jan 1, 1995

By Michael D. Zuber

This paper discusses the use of a coalbed methane simulator that has been modified to account for the removal of grid blocks as a function of time to estimate gas emission and production for a variety of mine-associated problems. The specialized features of the simulator are presented. Example applications illustrate the models&apos; use in estimating methane emission rates during mine roadway development, and estimation of longwall panel degasification by horizontal boreholes.

Jan 1, 1997

By Yoshiak Mizuta, Hi Keu Lee

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium

Jan 1, 1986

Paper and paperboard manufacturers need to quantify the carbon footprint and environmental impact of their products to satisfy market, social and government demands. Coated paper products contain minerals, such as kaolin and calcium carbonate, at significant levels; some coated paper grades have mineral contents as high as 45% by weight. Some uncoated paper has no mineral content, but most uncoated paper contains some mineral to improve appearance, process efficiency and cost. Super-calendared paper grades can contain levels of mineral up to 35% by weight. This paper describes how to calculate the carbon footprint of kaolin and calcium carbonate minerals used for white pigments. The carbon footprint of these minerals strongly correlates to the primary energy sources, final product form and energy used to calcine kaolin and lime. Kaolin and calcium carbonate pigments have a favorable impact on the carbon footprint of paper and paperboard products by directly substituting for fiber and by reducing the energy needed for paper making. Key words: Kaolin, Calcium carbonate, Paper production, Carbon footprint, Lifecycle analysis

Jan 1, 2010

By T. E. Breaux

Repair of large rotating apparatus such as ball mills is uncommon but under certain circumstances is achievable. This paper describes the successful repair of trunion on a 14 foot diameter by 20 foot long ball mill. Diagrams of the repair are included for visual perspective and non-destructive test procedures are outlined.

Jan 1, 1988

By A. Giblett, J. Shuttleworth, R. Dunne

In a previous paper (Dunne, Martins, Goulsbra, Chittenden 1997), the new gravity circuits at Telfer Gold Mine, which incor­porate Knelson centrifugal separators in both the sulphide and oxides, are described. The advantages of the new circuits over the replaced spiral ( oxide circuit) and jig (sulphide circuit) were discussed, as were the improvements in gravity gold recovety. It is of note that the installation of the centrifugal separators in themselves did not result in increased gold recovery. The realisa­tion that changes in gold room practices are required to take advan­tage of the increased fine gold recovery from the Knelson concen­trator was an important step towards improved gravity gold recov­ery. This was achieved by increasing the time taken to treat the Knelson concentrate on the shaking table in the gold room. Although this increased gold recove1y, it was found that the table tailings, especially from the sulphide circuit, still contained high values of gold. In an effort to ascertain ways in which gravity gold recovery could be fu1iher improved, a sample of the sulphide table tailings was sent to the Oretest Laboratory in Perth for testwork. The results from this program are discussed in this paper.

Jan 1, 1998

By Murat Budakoglu

Albite (NaA1Si308) is one of the important raw materials for the rapidly developing Turkish ceramic and glass industry. Prior to 1980, development of the ceramic industry in terms of raw material was dependent upon small-scale mining operations; in the last decade, these efforts have increased substantially. The aim of this study is to investigate the geochemical properties and distribution of albite occurrences in the Kocayayla district, which is about 12 km northeast of the town of Milas, about 50 km west of the city of Mugla in southwestern Anatolia. Kocayayla is also well known for its famous ancient city, Labranda. The field area is located in the Menderes Massif, which was formed by major tectonic events during the Late Proterozoic and subsequent periods. The target area was studied to prepare a detailed geological map (scale, 1:10,000), and to determine the formation of albite-mica-schist-quartzite borders in the host rock gneiss. To do this, systematic sampling of albite was done in the two main areas, the Sarikaya and Yumruta? regions. In the study area, albite zones are scattered within an area of about 20 km2, and they extend in a northeast-southwest direction; mica-schists and quartzite veins accompany these units. Mineralogical observations show that quartz is the main mineral associated with albite. In the ceramic industry, the albite + quartz assemblage is well known and is classified as "standard" or "super type," depending upon the content of TiO2 and Fe203. In this study, the Sarikaya albites (profile I) exhibit remarkably lower TiO2 (0.15% on the average) values contrasted to that of Yumruta? (profile 11; 0.24% on the average), whereas Fe203 values vary slightly from 0.076% to 0.085% in both regions.

Jan 1, 1999