Search Documents

By David I. Dr. Hoyer

The Hicom mill is a conical mill in which a ball or autogenous load tumbles within a high-intensity acceleration field. An autogenous Hicom mill with a power density of about 1100 kw/m3 and a volume of just 4 litres reduced a 50 m quartzite feed to 90% passing 38 microns at a feed rate of 160kg/h (in closed circuit with a hydrocyclone). Batch tests have identified fracture, chipping and abrasion breakage mechanisms at pebble sizes of 5 to 50 mm. The special behaviour of the load in Hicom mills was exploited to develop a novel technique for estimating steady state autogenous load size distributions.

Jan 1, 1992

By P. A. Tuzinski, L. J. Dahl, N. R. Adamson, S. E. Brink, R. L. Blake

The US Department of the Interior, Bureau of Mines is developing a process to selectively extract manganese from oxide ores as part of its in situ mining research program. The Bureau is conducting site characterization studies of two manganiferous iron-formation deposits. These studies include: drill core, regional stratigraphic relationships from the existing geologic database, ore body geometry, geologic structure, hydrologic conditions, accessibility of ore minerals to leach fluid, surface subsidence potential and data collected from laboratory leaching experiments. This information is being used to evaluate the technical, environmental and economic feasibility of in situ mining of manganese for these two deposits. This paper will focus on the stratigraphy, mineralogy, ore textures, fractures, permeability and porosity as they relate to in situ mining.

Jan 1, 1994

By G. Baudet, M. Save

Ethoxylated phosphoric ester surfactants were evaluated as collectors for flotation of carbonates from sedimentary phosphate ores, at slightly acidic pulp pH, using sulfuric acid or sodium fluorosilicate as a phosphate depressant. With 12 to 15 carbon atoms in the hydrophobic chain, maximum collecting power was observed for 9 to 10 ethylene oxide units. Only fine carbonates, ranging in size from about 20 to 160 µm or 40 to 200 µm, were effectively removed with phosphoric ester collectors. Utilization of seawater, or water of extremely high hardness, did not detrimentally affect selectivity. Silica, silicates, and residual fine carbonates can be separated in a second flotation stage, with primary amine as a collector. Coarse carbonates are separated by direct flotation of phosphate with fluoride ion as a phosphate activator and primary amine as a collector. In a seawater pulp, fluoride ion was not required. Typical examples of laboratory and pilot- scale test results are given to illustrate capabilities of the various flotation flowsheets.

Jan 1, 1999

By V. R. Manukonda, I. Iwasaki

Selective flocculation of iron ores is extremely sensitive to the type and amount of soluble salts in pulp solutions. Chemical precipitation of alkaline earth ions combined with ultrasonic treatment deactivates their adverse effects without using any environmentally ill-defined reagents. The manner in which ultrasonic treatment affects starch adsorption on hematite, dissolution of quartz, and the selective flocculation process was investigated. Selective flocculation tests were conducted in the presence of up to 400 ppm calcium ion on a quartz-hematite mixture by precipitation as calcium carbonate, and the role that silicate ion generated by ultrasonic treatment plays in achieving the selectivity of separation is discussed.

Jan 1, 1988

By R. C. Oberth, C. F. Lee, E. M. Taylor

INTRODUCTION Underground siting of nuclear power stations is drawing increasing attention in various parts of the world. Scandinavian countries took the early lead in this field because of their experience in the design and construction of underground hydroelectric stations and industrial plants, and because they have near-surface rock formations which are ideally suited for hosting large underground caverns. The world's first underground nuclear facilities were built in Norway (Halden) and Sweden (Agesta) and were commissioned in 1959 and 1963 respectively. Figure 1 summarizes the main features of these and two other small-scale European facilities. (1-4) American utilities and regulators are also for a variety of reasons assessing the benefits and penalties of underground siting. A recent study by Sandia Laboratories (contracted by the Nuclear Regulatory Commission (NRC) focussed on identifying potential safety benefits of underground siting. (5) Although the study concluded that underground plants would have improved containment for some accidents, as well as better external protection, NRC, in assessing the overall benefits and penalties, decided not to impose mandatory underground siting for nuclear stations. In June 1976, the California Legislature enacted a law which directed the California Energy Commission (CEC) to examine the issues concerned with underground siting of

Jan 1, 1979

By R. R. Oder, R. J. Gray

We report measurements of the effects of rank, type, and grade of coal on grinding energy and grinding media consumption in a Pitt Mill. The rank of coal has a greater effect on grinding energy than does coal type. The effect of coal grade on grinding energy depends upon the relative grindability of the mineral matter and of the hydrocarbon components of the coal. The mineral matter is primarily responsible for abrasive media wear in a Pitt Mill. The widely recognized HGI test for coal breakage may yield misleading results, particularly for multiple-banded bright and dull coal where the screening procedure used in sample preparation favors the testing of the hardest coal fraction. The work reported here indicates that the Pitt Mill, which grinds the whole coal in a single stage and which yields easily interpreted results, is an excellent candidate for testing coal pulverization characteristics including energy requirements and equipment wear. The measurements of the effects of coal characteristics on grinding energy and on media consumption have been used to estimate the cost of fine grinding in a Pitt Mill. The results, based on a conceptual level evaluation of grinding at the rate of 1 TPH, show that there are trade-offs possible between the cost of energy and cost of media consumption which involve choice of grinding media size. The use of fine-size grinding media to lower grinding energy and to increase throughput can be deceptive because the total cost of grinding must consider both energy and media consumption.

Jan 1, 1992

By Sizhe Tan

An open pit mining operation can be considered as a production system with at least two products: ore and overburden (waste). A primary mine planning task is to schedule the production of ore and waste over its life span subject to several technical and economic constraints to maximize some objective such as the overall profit from the operation. Two major constraints are (i) the feasible combinations of ore and waste productions and (ii) the limiting function for ore production as a function of mine life. The task in scheduling production and stripping ratio (ratio of waste to ore production) is to find an ore production curve below the upper bound function of ore production, and a stripping ratio curve within the feasible domain of ore production and overburden removal while maximizing the defined objective. Zn this paper, feasibility of developing computerized optimization models to perform such a scheduling process is explored. Two optimization models are proposed for the task. In the first approach, a linear programming (LP) model is employed and in the second, a dynamic programming procedure (DP) is outlined. In these models, in addition to the consideration of the two major constraints mentioned earlier, various other contributing factors such as interest rate, equipment purchase cost and installation schedule, operating cost, and equipment idle cost are incorporated. An example is provided to illustrate the LP model application.

Jan 1, 1992

By V. Adamek

The specific lithological conditions over the Pittsburgh coalbed, highly resistive limestone and sandstone units with relatively shallow overburden, prevent the use of any predictive method as developed for European conditions. This paper describes the development of a subsidence precalculation methodology suitable to the mining-geological conditions in the Northern Appalachian Coal Field. It has been found that due to lithological conditions over the Pittsburgh coalbed the subsidence coefficient varies within the area of the subsidence trough. This is different from the European conditions where the subsidence coefficient is considered to be a constant. The effects of lithology, in-the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hypothetically homogeneous overburden and existing lithological conditions, while providing for different mining conditions. Field data from eleven Bureau longwall panel studies were used in the regression analysis. For each panel the characteristics of the variability of the subsidence coefficient along individual profile lines were defined. Regression analysis of the subsidence coefficients from all test sites on the location relative to the edge of the panel has yielded a third degree polynomial equation with a coefficient of correlation of 0.9999. All sensitivity tests have shown good results.

Jan 1, 1985

By H. Peter Knudsen

Karst hosted lignite deposits are characterized by variable thickness of lignite that was deposited in depressions in the karst topography and by the variable extent and shape of the lignite pods. Since the lignite to be mined will feed a mine mouth generating plant, an extremely important criteria in the mine plan is to assure continuous feed to the plant. The variability in both the extent of the pods and the thickness of the lignite within the pods must be taken into account in any mine design in order to quantify the risk that an area being developed will have enough lignite to feed the plant for the specified period. Indicator kriging was used to create a model of lignite thickness of the deposit. Pod boundaries were determined from the indicator kriging model by two methods. First, contour maps showing the probability that the lignite is above a minimum mining thickness were prepared. Using these maps the mine planning engineer can determine either conservative or optimistic boundaries. The second method recognized that the most costly error that can be made in the mine plan is to run out of lignite. Thus, a loss function was determined from the costs of overestimation and underestimation. Using this function, the probability that minimizes the risks of overestimation versus underestimation was calculated.

Jan 1, 1989

By Pentti Kallio

From the aspect of economic feasibility of mining, ineffective use of expensive mechanization investments is becoming a problem. In many cases, the machinery is in operation only 50 - 60 % of the total working time. The lost time when the machines are idle means a considerable over-investment in machines. The lost time, with LHD equipment in particular, accumulates from the following constituents: - the needs of the person operating the machine trips to the work site, lunch, coffee and other breaks, want for comfort, etc. - deficiencies in the monitoring and control systems for machine operation waiting periods at loading and unloading stations, unnecessary and erroneous actions, inefficient work, etc. - deficiencies in the machine condition monitoring system , and inefficient service and maintenance work The data transfer and computer technology of today provides means for resolving problems in several areas - including the area of underground loading operations. In the paper those areas of automation and data handling are considered which make possible an improvement in the usage and monitoring of LHD equipment. These fields are: remote control of equipment, use of TV cameras and monitors in remote control, locating equipment and data transfer down the mine, measurement of the load and the data storing system, systems for following the condition of the equipment, unmanned operation of equipment.

Jan 1, 1989

By F. Aurelian

The development of the uranium mining industry in Romania started in 1950. The exploitation of Bihor region, one of the most important metallogenic zones of the country, began in 1962. Uranium exploitation activities were ceased in 1995 due to the exhaustion of the ore deposits. Between 2001 and 2002, due to the entire mining zone closure, ecological rehabilitation and decommissioning was initiated. The proposed solutions, concerning terrain, equipment and buildings utilization were elaborated according to the guidelines of the Romanian Environmental and Nuclear Authority.

Jan 1, 2006

By G. F. Friel, G. S. Morrow, J. C. Edwards

An experimental program in the U.S. Bureau of Mines' Safety Research Coal Mine evaluated the effects of dead end crosscuts on the transport time of CO along a mine entry. The presence of carbon monoxide is a characteristic of a fire in its incipient stage, and is significant in the determination of a fire location in a mine from the analysis of arrival times of pre-set concentrations at CO monitors. In this investigation two entries, with a total of ten crosscuts, connected by a room were instrumented with CO sensors as part of a real-time monitoring and data acquisition system. Controlled release of 1% CO was monitored as the contaminant traveled the entries for several different configurations of CO sensors and exhaust fan settings. In addition to the normal longitudinal dispersion of CO due to turbulent mixing at the front of the CO wave, the induced rotation of air established within a crosscut by the entry flow diluted the CO concentration through entrainment. It was determined experimentally for the entry and crosscut configuration considered that the transport time for a specified CO concentration was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and total crosscut volume. The proper interpretation of the measured transport time of a specified contaminant concentration between sensors is important for mine safety in the isolation of a fire and plans for miner evacuation.

Jan 1, 1993

By M. H. Kotze, M. J. Virnig, G. Steinbach

Earlier work at Mintek on the development of gold-selective resins culminated in a plant-manufactured batch of the first generation of Minix resin. A subsequent pilot-plant campaign at a South African gold mine identified some problems with that resin. These included lower capacity and selectivity for gold compared with the laboratory prototype, and a slow but progressive loss in capacity as the resin was eluted and reloaded cyclically. These problems were overcome by chemical modification of the resin structure. Examples of these improvements are presented. The commercialization of a new resin for a new metallurgical application presents problems, which are exacerbated by the initial lack of demand for the resin because the process is unfamiliar to the mining industry. Progress in the commercial development of Minix is discussed in this context.

Jan 1, 1993

By R. A. Bauer

Investigations of bedrock within subsided areas over abandoned coal mines in Illinois reveal very little disturbance of the bedrock. In areas that have surface subsidence of 0.3 to 1 m (1 to 3.25 ft), examination of cores from exploration drilling and investigations of the boreholes by means of closed circuit television have shown that fractures are spaced at least 0.9 to 3.6 m (3 to 12 ft) apart. They are located within a zone 6 to 15 m (20 to 50 ft) above the collapsed area in coal mines 42.6 to 112.7 m (140 to 370 ft) deep. The dip of the fractures ranges from 25° to 60°, cutting across nearly horizontal sedimentary bedding planes. The amount of fracturing found in the collapsed area decreased as the amount of soft, weak materials increased in the immediate overburden of the mine.

Jan 1, 1987

By Wai Wu, C. Haycocks

The majority of Appalachian coal deposits lie in a multi-seam environment. Historically, the decision to extract a particular seam has been based on ease of access, ownership and economics rather than ground control considerations. As mining progresses and seams are being mined out, it is increasingly common to find working and abandoned mines in close vertical proximity to each other. Such contiguous operations can produce both positive and negative ground control situations in neighboring seams. These ground control problems, defined as interaction problems, are frequently reported, and their severity can range from minor roof problems that may require no additional support to complete loss of a large section of coal reserves (Stemple, 1955; Peng & Chandra, 1980; Haycocks & Karmis, 1983; Su et al, 1984). As a consequence, interaction problems are of growing concern to the Appalachian underground coal industry. Although interaction problems in multi-seam mining have been recognized for many years and many investigations have been conducted to study the problems, the ground control principles involved in their development are only partially understood. Previous research has identified four interaction mechanisms: pillar load transfer, innerburden shearing, arching effects and upper seam subsidence (Haycocks et al, 1982; Haycocks & Karmis, 1983). Pillar load transfer mechanisms and innerburden shearing have been successfuly used to explain interaction phenomena associated with undermining operations, while arching and subsidence have been used to assess problems during overmining. In addition, interaction-controlling factors such as cover, innerburden and seam thicknesses, extraction percentages on both seams, time delay between operations on two seams, and characteristics of innerburden rock have been identified and utilized in evaluation of interaction effects (Haycocks & Karmis, 1983; Webster et a1.,1984). As an example, Figure 1 shows the relation of innerburden layering and thickness to interaction on the lower seam. The combination of such theoretical work and the analysis of case study information has made it possible to determine, with a certain degree of confidence, the interaction damage in undermining conditions. The results of such an approach have been sufficiently successful and complete to be incorporated into a software package to assist field engineers in estimating potential interaction effects when undermining a previously mined upper seam (Grenoble et al, 1984; Grenoble & Haycocks, 1985; Grenoble et al, 1985). Although the conventional finite element and photoelastic modeling techniques have been

Jan 1, 1986

By H. D. Sharma

INTRODUCTION Uranium mill tailings, by-products from the mining and milling of uranium oxide contain all decay products of uranium-238, uranium-235 and all the Th-232. The ore containing all daughter products of the parents U-238, U-235 and Th-232 is ground to approximately 50% under 200 mesh particle size and after extraction of uranium, the residue, described as tailings, is discharged into natural depressions confined by dams. These deposition sites are referred to as tailings ponds. Tailings ponds are located in two mining districts, Bancroft and Elliot Lake in the Province of Ontario, Canada. Some parts of tailings ponds are dry up to a depth of several meters, whereas other parts have a water table very close to the surface and still others are covered with water. The extent to which the daughters of uranium isotopes are in equilibrium with the parents U-238 and U-235 is dependent on the age of the deposit in which uranium occurs and the extent to which the decay products are removed by geochemical processes. In the mining district of Bancroft, the deposit is known to be approximately 1 billion years old, whereas in Elliot Lake, the deposit is considered to be approximately 2 billion years old. The ratio of radiogenic lead isotopes Pb-206 and Pb-207, can provide some estimates concerning the age of the deposits. If the tailings are not affected by geochemical processes, the tailings would contain all the daughters of the 4n+2 and 4n+3 series in equilibrium concentrations. The equilibrium activities of some members of the 4n+2 series are calculated in Table 1. [ ] The amount of radiogenic stable lead isotopes depends on the age of the ore deposits. If the deposit in each district is of the same age, a definite relationship is expected with respect to the activity of Pb-210 and the radiogenic stable isotopes. Approximately 33 million tons of the tailings have been deposited in the early 1960's, approximately 20 years ago. During this period of storage, the segregation of uranium daughters, like radium, the diffusion of gaseous product, Rn-222, and removal of precursors by geochemical processes, can cause dis-equilibrium. Earlier work concerned with the uptake of Ra-226 and Pb-210 by plants (Kalin and Sharma, 1981), indicated that the concentrations of Pb-210,in samples of the tailings taken, were lower than the expected equilibrium. The diffusion of radon from a variety of matrices has been studied (Tanner, 1964). It has been shown that the diffusion coefficient is dependent on the particle size in which its precursor is present, the moisture content and the surface conditions. The direct measurement of radon concentrations in the environment near the ponds is dependent on the metereological conditions. Kramer, Schroeder and Evans, 1964, have examined the variations in the concentration of radon near the ground level with respect to atmospheric variables, such as changes in barometric pressure, precipitation, wind velocities, thermal atmospheric instability. It is difficult to relate the total release of radon from the ponds to the atmosphere over an extended period. Our measurements of Pb-210 and total lead on tailings samples taken from 16 sites indicate that the ratios of the activity of Pb-210 to the mass of total lead can provide parameters which are helpful in the estimation of the total amount of radon and its decay products diffusing from the tailings ponds. In this paper, we present the results of measurements of activities of Ra-226, Pb-210 and total lead in samples from various ponds situated in both mining districts. The measurements were confined to samples taken at 0-25 cm depth from the surface.

Jan 1, 1981

By I. Shah, L. G. Austin

A method for quantitative investigation of the phenomena involved in fine grinding of materials that follows the changes in the breakage rates of fine particles has been presented. For relatively hard, brittle, non-coating material like quartz, the slowing down effect of breakage rates starts to be significant at relatively coarse sizes, which goes often undetected in closed circuit grinding systems, producing relatively coarse product, say P80=75µm However, for fine grinding systems, as the -10µm fractions begin to build-up, and classification becomes more difficult, the build-up of fine sizes causes a slowing down effect Compounding this problem is the difficulty of obtaining accurate cumulative weight size distributions in the fine size region.

Jan 1, 1983

By Monica Pavlik, Thomas Wildeman

Water from the Forest Queen mine adit near Silverton, Colorado drains into a natural wetland. Because the pH of the water averages 5 and the iron concentration averages 18 mg/L, it was thought that the wetland might naturally treat the water. Of most concern with respect to the aquatic environment is zinc whose concentration averages 0.60 mg/L. Starting in October 1997, the surface waters, ground waters in the peat substrate, and the sediments in the wetland were sampled and analyzed four times over the course of four months. The adit water primarily remains as surface water where Fe, minor amounts of Al, and no Zn are removed. After the adit water enters the peat, then it is found that the pH rises to 5.8-6.5 and sulfate is reduced. The removal of Zn and A1 is caused by these two changes. However, Fe in its reduced state is quite soluble and may be remobilized in the reduced environment of the peat.

Jan 1, 2000

By R. E. Wardwell, J. D. Nelson

The design of cover systems for reclamation schemes in tailings requires estimation or determination of tailings materials properties such as compressibility, shear strength, and consolidation characteristics. It is very difficult and expensive to obtain truly undisturbed tailings samples for laboratory testing. In situ testing methods have been developed for economically obtaining large amounts of information. Two of these methods are described, the piezocone and the flat plate dilatometer. Both of these methods provide a rapid means of detailed material identification in a nearly continuous fashion for the entire depth investigated. The equipment is described and typical data from a uranium tailings impoundment is presented. The results are compared and the advantages and disadvantages of these methods are discussed.

Jan 1, 1987

By Ing. Alois Adamus, Ing. Václav Pošta, Ing. Lubomír Hájek

This paper reviews experiences connected with the use of nitrogen in the Czech coal industry. Special attention is focused on the first use nitrogen In the Czech Republic, it is probably the first case of fighting a mine fire using nitrogen in all the World. Discussion dwells on the present-day use of nitrogen, its sources, consumption, technological equipment, and the theoretical evaluation of nitrogen flushing.

Jan 1, 1995