Search Documents

By T. A. Gray

There are several potential large-volume uses for coal ash in mining-related applications that could be environmentally and economically beneficial to mining companies. Actual usage, however, may be constrained by regulations or by perceptions of coal ash and the potential uses. To identify currently allowed uses and to assess constraints to coal ash use in the eastern coal fields, questionnaires were sent to state coal mining agencies to determine their policies on coal ash utilization and to mining companies to solicit their viewpoints on coal ash utilization. Identifying and understanding the constraints will allow for the development of a coordinated and consistent approach to remove or reduce these constraints and possibly allow for increased utilization of coal ash by the mining industry. This paper summarizes the findings of our investigation.

Jan 1, 1995

By Julian S. Edwards, C. Frederick C. Pearson, Sevket Durucan

Information gained at the site investigation stage of the Carsington aqueduct project led the designers to suspect that methane might be encountered during tunnelling and therefore gas detection techniques, including emergency shutdown systems, were introduced. After construction, on completion of the excavation and lining of the tunnels, a survey showed that methane was entering the aqueduct dissolved in infiltrating groundwater. General body air concentrations were very low but on closure methane concentrations rose rapidly within the aqueduct. A research project has now been initiated to investigate the mechanism of methane generation and entry rate into the system, the results of which are being taken into account in the preparation of future operating procedures.

Jan 1, 1989

By F. Soumis

This paper describes an integrated procedure for the very short term production planning of an open pit and the execution of this plan: the truck dispatching. Integration of plan and dispatch means that the plan is realistic so that its objectives can be realized by the dispatch. This realism is obtained by supplying the plan optimization, which involves mixed integer programming, linear programming and non-linear programming, with experimental O.R. models of waiting and blending. The arrangement of these models in the computer programm has made it possible to obtain very short computing time for the planning in spite of the width of the optimisation. The dispatching of a truck is made by solving a classical assignment problem for each dispatch over a horizon of the expected*next 10-15 trucks to request dispatches. This deep-reaching dispatch procedure uses the continuously arriving information about trucks' positions and shovels situations and models by probability functions the expected waiting time of shovels and trucks. In this manner trucks and shovels are synchronized and last moments' opportunities for productivity gains can be obtained. The dispatch procedure takes .5 second on PDP11. This integrated planning and dispatch procedure gives high productivity while ensuring good blending. Results from the Mount Wright mine of the Quebec-Cartier Mining Co., where the integrated procedure has been installed on the existing computer equipment PDP11, are included.

Jan 1, 1989

By Ralf Vergeiner

The most famous landmark of the city of Graz (Austria) is the clock tower on the castle hill. An underground chamber was built as a multifunctional structure beneath this landmark. The required structure was designed as cavern. The overburden to the clock tower in the north side of the cavern was only 30 m. To allow access from the city to the chamber and the clock tower, a vertical shaft was built near the cavern. Rock excavation was by drill and blast method. The pilot shaft was made by the raise-boring method. Because the location of the building site was in the center of Graz, special care was taken to minimize deformations and vibrations so as to protect surrounding buildings.

Jan 1, 2001

By G. Johnston, P. K. Chatterjee, S. Holguin

Underground mine planning is largely manual and can demand considerable resources to generate a working plan and to perform limited tests of sensitivity to variations in geological and mining conditions. It is possible to use computer aided mine planning to automate many of the manual procedures to allow the planner to evaluate a number of layouts, extraction strategies, and schedules. his paper examines the simulation and scheduling of an under- ground coal mine operation through the-use of on- screen graphics. The simulation will provide a basis for predicting productivity and other relevant information over a specified number of shifts. The software developed is extremely user friendly and reduces the tedium of repetitive manual calculations inherent to mine planning and drafting to a minimum, thus offering considerable savings in an area that is widely recognized as extremely labor intensive.

Jan 1, 1988

By Richard R. Klimpel

This paper reviews some of the factors involved in selecting amine flotation reagents used to remove silica from ores. A comparison is made between the chemical reagent design approaches used to identify flotation reagents that are used to recover silica- and oxygen-containing minerals and the chemical reagents used to recover sulfide minerals. This introduction gives practitioners who are involved with oxide- and carbonate-type minerals and who may not be familiar with sulfide mineral flotation some ideas of the chemical reagent design challenges that exist with froth flotation on a broader scale and why oxide type mineral flotation reagents are what they are. This is followed by several sections that discuss various classes of available amines. The closing sections emphasize that the optimal choice of an amine collector depends not only on that amine's specific chemical characteristics and costs but also on the operating conditions, especially the flotation feed particle size distribution.

Jan 1, 1999

By John B. Comer

Compelling evidence indicates that at least the plateau bauxite of northern and central Jamaica formed from volcanic ash. The predominance in plateau bauxite of zircon grains younger than the host limestones and the relative abundance of zircon grains having idiomorphic form support a direct ash-fall origin for much of the bauxite parent material. Based on revised mass balance calculations, not enough of the middle Eocene to lower Miocene host limestones have been dissolved to make an important contribution to bauxite. Likewise, the pre-middle Eocene rocks of Jamaica have made only a very small contribution to plateau bauxite; they may have made a more significant contribution to the graben bauxite of southern Jamaica.

Jan 1, 1984

By Q. X. Yun

This paper presents a new approach to optimize the transportation system in open-pit mines. The new approach employs artificial intelligence, fuzzy sets, dynamic programming and CAD technique to determine the transportation system. The determination consists of 4 phases: initial selection, road alignment, final decision .and open-pit drawing.

Jan 1, 1992

By Y. Tao

The features of the teeter bed separator and its application in the coarse slime separation of Chengjiao coal preparation plant were discussed. The relationship between the coarse slime separation efficiency by TBS and the particle size were studied, and the influence of using TBS on dense medium consumption and oil consumption were investigated, it increased the clean coal yield and the comprehensive recovery of the whole plant, and brought huge economic benefits to Chengjiao coal preparation plant.

Jan 1, 2011

By R. J. McGregor

The Internet has revolutionized worldwide communications. Any real or perceived mining incident or environmental spill, no matter how small or remote, can become a disaster of "biblical proportions" through the judicious use of the Internet by environmental and anti-mining groups. In addition, mining companies' own Web sites and unofficial message boards can provide plenty of additional ammunition to the anti-mining forces. This paper explores how the Internet and readily available information are used by anti-mining groups active on the Web.

Jan 1, 2001

By W. J. Wuest, M. J. DeMarco, J. R. Koehler

Yield-pillar-based gate-road designs often fail to provide mine operators with adequate ground control. This is because of the unknowing m is employment of "critically" sized pillars. A "critical” pillar is one that is too large to either yield nonviolently or to yield before the roof and floor sustain permanent damage and is too small to support full abutment loads. To demonstrate the critical pillar concept, afield study of a tapering gate road was conducted by the US Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m (55.1-ft) wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m (40-ft) wide design more closely approaches proper yield pillar dimensions. A probe hole in several 10.6-m (34.8-ft) wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1997

By Roman Pyrih, Jim V. Rouse

Because cyanide is a naturally-occurring chemical, geochemical and biogeochemical mechanisms exist to retard or attenuate the movement of cyanide and its compounds in the subsurface and to degrade such compounds into low-hazard reaction products. The attenuation capacity of subsurface earth materials can be measured, predicted, and enhanced by simple and inexpensive procedures. The paper describes methods of testing the geochemical and biogeochemical attenuation capacity of the subsurface and offers general suggestions for methods of enhancing such capacity. It also presents examples of data which documents such attenuation.

Jan 1, 1991

By K. M. Stone, N. J. G. Masson, A. C. Woollett

The Jabali zinc deposit in Yemen contains at least 9.4 Mt (10.4 million st) of ore at a grade of 10.7% zinc, 2.2% lead and 77 g/t (2.2 opst) silver. The zinc occurs as smithsonite with minor hydrozincite. The Jabali ore does not produce a zinc concentrate of sufficient grade to be acceptable to a conventional zinc smelter, and it has been necessary to formulate a less-conventional development plan. This involves the construction of a mine and concentrator at Jabali and a metal production facility using a new flowsheet designed specifically for the treatment of oxide material at Yanbu, Saudi Arabia. To give the facility the necessary economies of scale, the Jabali concentrate will be supplemented by feed from other deposits, this may be either oxide or sulfide material. The paper outlines the geology and proposed mining and treatment operations at Jabali, presents the flowsheet for Yanbu and estimates preliminary costs for both operations.

Jan 1, 2003

By M. J. McPherson, P. Mousset-Jones, G. Danko, I. M. Konduri, F. Calizaya

The flow of air through a bare rock, underground airway is affected by the size and frequency of the micro- and macro-asperities of the rough surface. The focus of this study is to characterize this roughness using the coefficient of friction, the friction factor and the fractal dimension. The rough surfaces were identified by two sets of 177 and 78 transverse profiles measured by a laser profiler along the length of an underground airway at the Sunshine Mine, Idaho. Based on the measurements, the friction factor was estimated from Atkinson's equation and the coefficient of friction from the Moody diagram, and power series and variography were used for computing a fractal dimension for the airway surface. Significant conclusions are reached relating the effect of error in the measurement of cross-sectional and rubbing surface areas of a drift, on the estimated friction factor for the airway. The potential role of the fractal dimension as an alternative to the friction factor for characterizing the roughness of a mine airway is discussed.

Jan 1, 1993

By Birger Schmidt

INTRODUCTION Urban tunneling in soil poses a unique set of problems to planners, designers and contractors. One of the important concerns is the impact of tunneling on the environment: not only the effects of noise, vibrations, construction traffic and surface traffic diversions, but also the effects of ground movements and dewatering on existing structures and facilities. Underpinning or other protection of structures often consume more than 10% of the total construction cost of an urban rapid transit tunnel, and another unknown percentage is expended on construction procedures designed to minimize these environmental effects. Ideally, many basic planning and design decisions should be based on reliable predictions of ground movements due to tunneling. Some of these decisions are: the choice of tunnel alignment and depth to minimize risks and effects of ground movements; selection of schemes to protect existing structures through soil improvement or underpinning, or outright acquisition and possible' demolition; relocation of utilities; selection of procedures for construction monitoring and project control; and the choice of construction and lining methods. To make rational decisions of this nature, the owner and his designers must perform analyses that will balance risks and costs of a variety of alternatives; but to make meaningful risk analyses, they must employ rational methods of predicting ground movements and their effects and must know the reliability of these predictions. Of course, the risk analyses also must consider politics, public relations, insurance and liabilities.

Jan 1, 1974

By Jack D. Melin

The commercial development of the Liwell Screen is a result of a thorough search for a non-blinding and highly efficient screening device capable of handling even the most difficult-to- screen feed materials. A proprietary development of Hein, Lehmann A.G. of Duesseldorf, West Germany, the Liwell Screen utilizes a unique flexible deck motion for sizing a variety of sticky, high surface moisture feed materials including raw coal and lignite at separations ranging from 3/4-inches (19mm) down to 10 mesh (1.5 mm).

Jan 1, 1983

By M. J. Meulendyke, J. D. Purdue

Within the mineral processing industry, a range of grinding conditions exists which include semiautogenous grinding (SAG),rod milling, and conventional ball milling. Each of these mill environments presents a unique environment for grinding media, requiring the application of specific physical and chemical properties for optimum grinding media performance. The environments are characterized by varying degrees and combinations of abrasive, corrosive, and impact wear. An extensive test program has been conducted to determine the extent wear rates vary between these different applications. Test results are related to production results, ball size, and mill operating conditions.

Jan 1, 1990

By R. J. Gochin, G. D. Schena

Mineral processing options and technical innovations should be financially assessed. Indeed technical feasibility alone does not offer an adequate process selection criterion. An appraisal by the use of engineering economics principles leads to a more efficient evaluation and selection of feasible mineral processing solutions. Financial consequences of different options synthesised by profitability indices allow better decision making. Selected examples derived from real world problems are used to illustrate the potential of engineering-economics methods applied to mineral processing.

Jan 1, 1995

By A. M. Taweel, M. T. Ityokumbul, A. I. A. Salama, M. W. Mikhail

The liquid-phase mixing within CANMET's Western Research Centre's (WRC) 0.76-m-diem pilot-plant flotation column was characterized using a salt tracer. The process variables studied were frother addition and, gas and liquid flow rates. The response of the column to a tracer pulse was monitored at three axial and two radial locations. The results showed that the 2-tph flotation column was well mixed. Discussed are the implications of this observation to column design and scale-up.

Jan 1, 1996

By C. J. Pritchard

Productivity improvements reduced the number of continuous miner sections from seven to three while maintaining full productive capacity. So a decision was made to test an advancing tailgate ventilation system on the shortwall mining section. Having the shortwall mine its own return air system has freed the third mining section for more productive, less costly mining. The advancing tailgate has provided effective ventilation across the face and gob with acceptable pressure losses. The low-productivity, tailgate-development, continuous-miner section has been transformed into to a high-productivity, development-retreat section that is also available for long-term mine development duties, increasing mine planning flexibility.

Jan 1, 1991