Search Documents

By Roger B. Jr. Herbert

Surface water samples were collected from water accumulations at the surface of a neutral pH mine tailings deposit in Kristineberg (Sweden) where algal growth and iron hydroxide precipitates were observed. Ferric iron in the aqueous samples was determined by (adsorptive) differential pulse - cathodic stripping voltammetry. The analyses indicated that labile Fe3+ concentrations were in the range <20 to 337 nM, while total Fe3+ levels were much higher at 0.9 to 8.3 uM. The labile Fe3+ levels are more than two orders of magnitude greater than would be expected based on equilibrium with ferrihydrite. These results suggest that iron complexation with strong ligands in the surface water competes with iron hydrolysis, and that these ligands may be of algal and/or bacterial origin.

Jan 1, 2000

Research has determined that ground control interaction problems in mining over a previously mined seam occur primarily in the tension zone created at the edge of the subsidence trough, and in areas above lower seam remnant pillars. Based on empirical and analytical studies, planning options for improving conditions on the upper seam have been developed to optimize extraction while minimizing the negative effects of seam interactions. These options include prediction of potential upper seam damage, guidelines for minimizing inevitable negative interaction effects, and recommended opening and pillar sizes, shape, and orientations, as well as design and planning procedures.

Jan 1, 1988

By L. Wade, D. R. Pearce

A detailed account is given of the spectral ratio laboratory method for the determination of seismic velocity and attenuation through rock cores under simulated in-situ stress conditions. An account of a computer program called AUTOQ is described for automatic processing of a complete set of laboratory results. Some of these results are shown and discussion is directed to- wards the suitability of in-situ velocity or attenuation measurements in determining rockmass condition or stress regime.

Jan 1, 1996

There has been some confusion over the selection of discount rates when performing stochastic simulations of a project&apos;s net present value (NPV) using risk- adjusted discounting techniques. Some argue that lower discount rates should be used when performing stochastic valuation simulations. This creates higher NPV values and improves the attractiveness of a project. Others argue that the discount rate should not be lowered for these simulations. This paper exposes the source of this confusion. It demonstrates that stochastic simulations do not remove the risk inherent in a project and, therefore-do not improve a project&apos;s value to the risk-averse investor. Risk-adjusted discount rates should, therefore, not be adjusted downward when performing stochastic NPV simulations. Stochastic simulations are, however, shown to he useful in several aspects of project valuation.

Jan 1, 1996

Diamond wire rock cutting is the most widely used technology in carbonate stone quarrying owing to technical performance and block face quality. Interest is also growing for siliceous deposits. This paper deals with the problem of optimum wire utilization under restrictions regarding a set of variables and parameters. A computer program of general applicability has been set up with the aim of studying the most suitable combination of technologies and the effect on the technical and economic results of bench geometry, overall quarry yield, market -stone value, quarry size as well as the quantity, productivity and price of human and material resources and their organization in the elemental working cycle. Two quarrying problems are considered as significant instances a granite and a travertine quarry. The results are illustrated and discussed.

Jan 1, 1989

By E. Forssberg, Y. Zeng

Fine crushing and rod grinding have been investigated using a laboratory-scale jaw crusher and a rod mill. The net energy consumption in both crushing and grinding was evaluated from torque measurements. An empirical relationship was established between energy consumption, particle size and operating parameters. When the mill feed size is reduced, through fine crushing, to about 80% passing 3 mm, the energy consumption will be minimized in a comminution chain of fine crushing and coarse rod grinding. The results in fine crushing were compared with a large-scale test.

Jan 1, 1993

By J. A. Burger

Research in the eastern U.S. has shown that productive mine soils and forests can be restored using the following guidelines: (1) cooperation among the mine operator, landowner, and regulatory authority in developing the mining permit; (2) replacing topsoil or creating a desirable medium in which trees are planted; (3) loosely grading non-compacted topsoil; (4) using native and non-competitive domestic ground covers that quickly protect the site; and (5) planting a proper silvicultural mix of crop trees for their commercial value along with nurse trees for wildlife and soil improvement.

Jan 1, 2002

By Bruce Johnson

This paper is not written to "break new ground" in computer applications; it is just a treatment of how an operating metal mine utilizes a mainframe computer for planning, analyzing, and reporting on the ventilation and cooling systems. The Unisys mainframe computer at the mine site is used in programs that analyze the ventilation network, keep records on various ventilation installations, calculate the results of measurements and produce reports on ventilation conditions in the working places and on the main air distribution, and plan and analyze the cooling system. All the programs are interactive to terminals. There are a series of data files that are generated by some programs which may be used by other programs. Most of these programs have been developed in-house. The computer is also used as a word processor via a vendor-supplied text editing program to produce memos, letters, and to keep up-to-date lists of equipment used.

Jan 1, 1989

By Robert F. Hauck

This chapter discusses a new technology for computer control in open-pit mine operations: the real time automatic dispatching of manually driven trucks to shovels. The monitoring of truck activity is accomplished by detection of local radio signals. Computer-operated directives are communicated to drivers by remote controlled digital display units inside the truck cab. The production objective is to maximize tonnage in a cost effective manner. The problem is formulated in the appendix and the solution method is briefly described. Side conditions such as maintaining delivered ore grade aims, balancing waste to ore volumes to keep within stripping ratio tolerances, and meeting production rate requirements temporarily established for certain shovels are also discussed. Experience with a developed event- to-event simulator applied to analyses of several North American mining operations using this technique is summarized. Complete systems employing this technology are now under- going installation at mine sites in Canada and the United States.

Jan 1, 1979

By G. D. Elliot, R. L. Grayson, G. L. Winn

For the years 1990 and 1991, West Virginia&apos;s underground coal small-mine fatality rate was approximately 10 times higher than the national coal-industry fatality rate. Although the number of fatalities went down from 22 in 1991 to 17 in 1992, West Virginia still led the nation in coal-mining fatalities. A team of mining and safety professionals from West Virginia, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners&apos; Health, Safety and Training, studied this problem. A clear path for formal intervention was determined and is presented here.

Jan 1, 1996

By Steven W. Hunt, Ronald E. Heuer, Safdar A. Gill

A 3.3 m (11 feet) diameter, 51 m (168 feet) deep temporary steel casing which had been sunk within glacial soils buckled and collapsed on July 29, 1985. The collapse occurred at the CT-8 Dropshaft site in Milwaukee while two workmen were contact grouting outside the casing in an attempt to stop groundwater inflows through a bottom plug. This paper describes the soil and groundwater conditions at the site, the casing design, the method of shaft construction, and probable causes of the buckling failure. Specific aspects of the paper include: slurry method of shaft excavation and casing installation, soil creep, earth pressure due to three dimensional arching, and buckling strength of a casing surrounded by slurry rather than grout and firm soil. The paper should be of interest to designers and constructors of temporary ground support systems for deep shafts.

Jan 1, 1995

By Daniel Hodouin, Antoine Berton

Mineral processing plants are monitored and controlled using measurements that are usually processed by on-line material balance calculation techniques. However, gross errors, due to sensor biases or failures, may corrupt all the process variable estimates. On-line gross error detection methods are required to ensure efficient mass balance evaluation. In the proposed approach, material imbalances and raw measurement corrections are tested by statistical techniques designed to detect and isolate sensor problems.

Jan 1, 2000

By George A. Lawrence

A new super-large 100 m3 (3500 ft3) pneumatic mechanical flotation cell is now available to meet today&apos;s mineral processing challenges. Several innovative design concepts represent a marked departure from conventional flotation cell designs. The radial discharge from the pump action rotor and the overhung vane type stator is contained in a conical bottom round tank with no dead comers. Peripheral launders collect froth overflowing the entire circumference of the tank and these launders are of a hexagonal design permitting cells to be nested together in a honeycomb fashion. The mechanism drive is either a customized right angle gear reducer or a conventional Vee belt drive. Both drive systems are available with an optional variable frequency control system that permits infinite speed adjustment of the rotor in each flotation cell or group of cells. Results of side-by-side comparative testing between three major manufacturers of super-large pneumatic mechanical flotation cells are discussed. These results were obtained at a large copper concentrator in Chile during several weeks of commercial scale testing.

Jan 1, 1995

By Hans-Werner Tonscheidt

Introduction The endeavours to mechanise the shaft sinking operations have led to the development of shaft boring using a V-Mole. The method implies competent ground and a pilot hole of sufficient verticality. This connects the top and the bottom of the shaft and serves for air ventilation and the transport of mullock. The shaft boring machine - nick name V-Mole - with a general pattern similar to a tunnel-borer reames the pilot hole to the designed diameter of the shaft. (Figure 1) The excavating of the rock, the removal of the mullock from the face and the lining of the shaft wall are done simultaneously. If they can be done also continuously this than creates a high potential of productivity. The verticality of the shaft can be garanteed due to the laser beam guided steering system. The diameter of the shaft is variable in steps of 0.5 m between 6.0 and 10 m in accordance with the need. It decides the capacity of the V-Mole to be applied. The depth of the shaft does not depend on the machine. It is practically unlimited as long as a suitable pilot hole is available. Up to 1988 almost 12.656 m of shaft have been drilled on 40 individual projects in Germany and the U.S.A. using a V-Mole. The rocks penetrated were Carboniferous sediments consisting of Sandstones, Shales, Conglomerates and Coal seams. The average uniaxial compressive strength was in the range of 300 - 700 Mpa with a maximum of 1700 Mpa in some singular sandstones.

Jan 1, 1991

By Birger Schmidt

The design of underground nuclear waste disposal facilities poses new problems related to the requirement of long term safety against radionuclide migration. The degree and effects of rock disturbance caused by construction and by the long term thermal effects from the hot waste must be predicted with confidence. Computer modeling can, to an extent, be verified by accelerated near-surface tests. Credible extrapolation to deep, long-term conditions requires successful near-surface modeling verification, proper characterization of near-surface and deep rocks, and successful determination of in-situ stresses. Excavation induced disturbance may be assessed primarily by empirical evidence.

Jan 1, 1981

By K. N. Han, J. J. Kellar, Y. Guan

The adsorption of zinc species onto silica in ammoniacal solutions was studied. The adsorption isotherms indicated that the adsorption of zinc increased with increasing pH. The adsorption density increased as the zinc equilibrium concentration increased up to =3.5x10-4 M. Above this concentration, the adsorption density was independent of the equilibrium concentration, and a maxima adsorption density was reached. Temperature had no significant effect on the adsorption density.

Jan 1, 1995

By Frank R. Cappuccitti

This paper will deal with current market trends for sulfide mineral collectors in three distinct parts; the global market for sulfide collectors, collectors as tools to solve mineral processing problems and new collector Research in the 1990&apos;s. The global market and manufacturing of sulfide collectors will be detailed as well as the trend towards using increasing amounts of specialty products. The use of Total Quality Concepts for laboratory and plant evaluations of new products will also be discussed. Research in the 1990&apos;s for sulfide collectors will need to focus not on the development of new chemical species but on the application of the new technologies that have already been developed.

Jan 1, 1994

By D. M. Richards, A. D. MacPhail

Highland Valley Copper currently mines two low-grade ore bodies, Lornex and Valley. The partnership was formed in 1986. As a cost reduction measure, it was decided to use an in-pit crushing and conveying system to deliver the ore from the Valley Pit to the Lornex mill 3 km (1.8 miles) away and 175 m (575 ft) above the pit rim. The system uses two gyratory crushers that feed a series of conveyors to transport up to 130 kt/d (143,000 stpd) to the main stockpiles. This paper describes the performance of the in-pit crushing system as it is currently configured, as well as its evolution to date and future planned moves.

Jan 1, 1995

By E. B. Johnson, G. Kjerbol, L. J. Holloway

The Mount Baker Ridge Tunnel is a major improvement of Interstate Route 90 in the State of Washington. The total length of planned underground construction is about 3,400 feet (1,040 m) of which 1,332 feet (406 m) will be constructed by a stacked-drift tunneling method. Sized for vehicular traffic on two levels, the net interior diameter will be 63 feet (19.2 m) requiring an exterior diameter of about 80 feet (24.4 m). The material to be excavated is predominantly stiff clay, and this will be the largest-diameter tunnel ever attempted in soft ground. A construction contract for the stacked-drift tunnel was awarded in late 1982.

Jan 1, 1983

By Marvin A. Ph. D. Friedman

The following paper describes an overview of evaluations for assessing the potential hazards associated with handling newly developed reagents used in the mining industry. Important factors in determining the risk and hazard associated with handling a particular chemical include hazard identification, dose-response assessment, exposure assessment, and risk characterization. The hazard evaluation step involves collecting and evaluating appropriate toxicology information on a chemical. This can include a comparison of the structure of a developmental chemical with that of a material with known toxicology information. Acute toxicology data, including oral, inhalation, and dermal LD50 values, eye and skin irritation data and sensitization or allergic potential information are typically generated for new chemicals. Environmental and in-vitro genetic toxicology data (e.g. Ames test) are also used to evaluate new mining reagents.

Jan 1, 1994