Search Documents

By W. H. Wilson, G. Bjarnholt, D. C. Holloway

This paper describes the results of field tests conducted on a 5x25m bench face to evaluate several new concepts for improving smooth wall blasting. These ideas involved the use of notched boreholes to direct the fractures and unconventional types and placements of explosives. The notches were made with a mechanical broaching tool, a water jet and with shaped charges. Borehole pressures were measured with an inexpensive and expendable pressure transducer developed for this program. The testing showed that at hole spacings 38% greater than normal practice, notched holes with half the normal loading density produced equivalent results.

Jan 1, 1986

By Madeline Mello, Michael Low, Nick Karlin, Bryce Scofield

The LA Effluent Outfall Tunnel is the first tunnel in the United States to incorporate post- tensioning into the precast segmental lining. Several unique components were integrated to ensure that the post tensioning could be carried out successfully in the tunnel, even concurrently with the TBM excavation. This also required the development of new processes both in the casting facility and in the TBM to ensure that the almost 3,700 rings could be successfully manufactured, threaded, stressed, and grouted. This paper will discuss the material selection, fabrication, and installation of, as well as lessons learned from, this first in country tunnel lining.

Jun 23, 2024

By I. Melik-Gaykazov, N. N. Melnikov, V. A. Fokin, S. P. Reshetnyak

Kola Mining Institute has been carrying out investigations of the possibility to steepen the walls of the Kovdor open pit with the design depth of 600 m. Steeping (up to 60°) wall angles is done by double height (24 and 30 m) benches with vertical slopes. One of the safety factors of mining with such walls is choosing the width of the safety berms preventing against rock falling from the slopes into the pit working area. The test on rock falling from 24 m benches has shown that vertical slopes are not more dangerous compared to the inclined(60-75°) ones.

Jan 1, 2003

By A. L. Mula

Pasaremos revista brevemente a 10s fundamentos de 10s ciclones, considerando un ciclón típico. Los datos gráficos disponibles en la literatura han sido convertidos en ecuaciones matemáticas por conveniencia. Se suministran los procedirnientos preliminares para seleccionar y diseñar tanto los ciclones como las bombas, y se facilita con algún detalle un ejernplo de cálculo para un hipotético circuito de molienda. En general, debe consultarse a 1os proveedores de ciclones y bombas para determinar un disefio definitivo. Algunos suministradores de ciclones emplean normalmente computadores digitales para el diseño definitivo con objeto de asegurar una gran precision.

Jan 1, 1982

By Bjørn Nilsen

"INTRODUCTION/BACKGROUND Weakness zones or faults containing clay-rich gouge represent one of the most challenging rock mass conditions to be encountered during tunneling. In Norway, such conditions count for a large part of the rock support costs, and in cases where the rock support has been insufficient, serious instability and cave-in have in many cases been the result. Most commonly, such cave-in has occurred after water filling of hydropower tunnels, but in some cases it has also occurred in tunnels under excavation and in completed “dry” tunnels. To avoid instability, two important requirements have to be fulfilled: 1) The location of the weakness zone and its character have to be identified in time. 2) The rock support has to be sufficient to withstand the loading caused by the zone. An incident which really brought the problems related to swelling clay into focus was the cave-in at the Hanekleiv road tunnel in 2006. Here, rock fall from the roof as shown in Figure 1 occurred unexpectedly about 10 years after the tunnel was completed. Fortunately this happened at a time with very little traffic, and nobody was injured. This incident emphasized the significance of the issue of swelling clay, although it was found to be caused also by gravitational collapse of the clay-rich gouge material of the weakness zone, and not related to swelling only (Nilsen et al. 2007).In this paper, main focus will be on discussing the characteristic features of swelling clay, test procedures which are being used for characterizing swelling clay, and the reliability of the results from testing for use in support evaluation and design in conditions with swelling clay. It is generally well known that swelling clay may cause considerable pressure on support elements, but quantifying this pressure for reliable analysis and design of rock support is still a great challenge."

Jan 1, 2016

By M. W. Osterberg

The Cyprus Pinos Altos mine exploits small high grade Cu-Zn skarns using trackless equipment and a modified room and pillar mining method. The skarns occur around early Laramide diorite and quartz monzonite stocks. Stage I calc-silicates and sphalerite developed in the Pennsylvanian Magdalena Group between diorite and the marble front and were partially incorporated into a diffuse breccia body. Stage II calc-silicates and Cu sulfides formed in the contact zone with quartz monzonite and along NE-SW faults, overprinting stage I rocks and breccia. The result is a geologically complex deposit formed in two distinct pulses.

Jan 1, 1992

By William G. Pariseau

Safety of mine ramps begins with an analysis of stress that almost certainly must be done numerically to take into account ramp geometry, route geology, rock properties, and pre-ramp stresses. The popular finite element method serves analysis purposes quite well. As a practical matter several obstacles to implementation need to be addressed including collection of rock and joint properties along the proposed ramp route, selection of ramp type, and specification of cross-section shape, size, and route grade. Additionally, stresses along the proposed route must be specified, preferably from in situ measurements. One need not be an expert in numerical methods to proceed to ramp design, although a background in mechanics of materials and rock mechanics is essential, and a first course in numerical methods is quite helpful. The necessary software is easily brought to the design task, more accurately, to the task of design evaluation. This software also addresses other important mine design problems including design of safe (1) main entries in stratified ground, (2) barrier pillars, (3) bleeder entries, (4) inter-panel barrier pillars, (5) room and pillar mines, (6) shafts, and (7) “tunnels” (Pariseau 2022).

Feb 1, 2024

By R. J. Sweigard

One possible alternative for disposal of flue gas desulfurization (FGD) by-products is use as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation of stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix proportioning of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48 percent and the peak stress could be decreased about 58 percent. The study indicates that fairly weak FGD materials can eventually lead to stability of backfilled highwall adits.

Jan 1, 1996

By T. E. Wilson

The length of Alaska's coastline, combined with the presence of a significant number of fjords, encourages consideration of marine disposal of mine tailings. However, the decision-making process is complex because various factors govern the viability of the submarine tailings disposal (STD) option. An expert system, called the Submarine Tailings Disposal Expert System (STADES), was developed to help mining project planners explore the feasibility of STD. A review of the existing literature, supplemented by engineering recommendations, on the various aspects of the marine disposal of tailings formed the knowledge base for the expert system. The shell used to develop the expert system was LEVELS.

Jan 1, 2003

By Thomas D. Henderson

Este capítulo presenta- un "caso histórico" de los pasos a dar para estimar IDS castes de capital y operativos para un concentrador típico de cobre porfirico de ± 9;070 toneladas métricas de producción diaria. El concentrador que se describe es hipotético, pero está basado en la experiencia propia y es, en efecto, una composición de varios proyectos reales. Las cifras utilizadas son ilustrativas solamente y no representan los castes reales de ningún lavadero en particular. Estas cifras son, sin embargo, representativas de los castes tipicos de molienda en un punto en el tiempo y son to suficientemente precisas coma para iIustrar los procedimientos de estimación de castes descriIos en este capítulo, No es posible publicar cifras reales y corrientes de los castes del lavadero y, en cualquier caso, las cifras de Ios castes reales pierden rápidamente su significación en Ia actual situación económica con los rápidos incrementos de las diversas partidas que configuran los castes. El trabajo está dividido en tres partes: (1) orden de la magnitud estimada, (2) estimación def estudio de viabilidad, y (3) comparación entre los castes estimados y los castes rea¬les. Con vistas a este trabajo supondremas que una mina tiene una propiedad minera explorada mediante perforación con testigos que refleja un yacimiento, ampliamente definido, como de unas 45,3 millones de toneladas métricas con una ley del d,6°/ de sulfuro de cobre, Esta compañia desea obtener primero una estimación del orden de magnitud de los costes (canto de los costes operativos como del capital) para determinar si la pertenencia garantiza más perforación y desmuestre de testigos. Suponiendo que esta evaluación económica obtenida utiIizando Ia orden de Ia magnitud de Ios costes sea favorable, sera a continuación requerido un estudio de viabilidad más preciso de los castes de capital y operativos. Seguidamente of recemas una descripción de los diferentes pasos dadospara desarrollar ]as costes del orden de primera magnitud y a continuación para los castes del estudio de viabilidad.

Jan 1, 1982

By J. A. Oraniscak

Longwall mining operations continue to increase extraction rates and the potential to generate higher amounts of airborne respirable dust (ARD). The National Institute for Occupational Safety and Health (NIOSH) has gathered data from underground longwall surveys and laboratory crushing tests to identify the important factors influencing the amount of ARD levels generated. Coal-seam characteristics, operational parameters (i.e.,cut sequence, mining height, etc.), extraction rates and dust-control parameters (i.e., airflow, water flow, etc.) were examined to determine their influence on ARD levels measured at longwalls during actual mining operations. ARD generated by a laboratory crusher while crushing bituminous coal samples collected from underground longwalls was also examined to determine if there were cor relations with coal-seam properties. Results from the longwall and laboratory data collected indicated that low-ash, high-volatile coals (low moist fuel ratio or MFR coals) generate higher amounts of ARD. It was found that face ventilation and water application to the coal product are essential elements to controlling longwall ARD levels.

Jan 1, 2000

By Peter Zhang, Daniel Su, Mark Van Dyke, Heather Dougherty

The integrity of shale gas wells in longwall chain pillars under the influence of longwall mining is a safety concern for both coal and gas operators. Previous modeling studies of gas wells in longwall pillars have shown that a FLAC3D model can predict longwall-induced stresses and deformations in gas well casings with reasonable accuracy. The predicted casing deformations can be verified by multi-finger caliper survey. This study concerns the influence of longwall mining on eight shale gas wells in a shale gas well pad located in the chain pillars between two adjacent longwall panels under 1,030 feet of cover. FLAC3D modeling was performed to predict longwall-induced deformations in gas well casings based on site-specific mining and geological conditions. Small deformations less than 0.5 in were predicted in the intermediate casing above 600 ft depth, and very small casing deformations less than 0.15 in were predicted below 600 ft due to high abutment pressure and high frictional resistance along the weak bedding interfaces. After the first panel was mined, a 56-arm caliper survey was performed on one of the wells to measure the longwall-induced casing deformations in the intermediate casing. The predicted casing deformations were then compared with the measured deformations, which indicated that the prediction was generally in good agreement with the measurement in terms of deformation locations and magnitudes. Findings from this study provide valuable information not only for stability assessment of shale gas wells in longwall chain pillars but also for developing engineering guidelines to preserve casing integrity through adequate pillar and casing design.

By Jamal Rostami, Tala Tahernia

TBM utilization rate is a component of machine performance prediction and critical for developing a reliable estimate of the construction completion time and cost of the tunnel. Estimation of the utilization rate involves identifying and quantifying the time dedicated to each activity in a tunneling jobsite. Ring building is a common activity in TBM tunneling and takes a large amount of tunnel excavation time when using shielded TBMs. This paper concentrates on the effect of tunnel diameter on the duration of downtimes related to ring building and examines the impact of machine diameter on downtimes. For this purpose, the dependency of segment installation time to segment configuration, and also the diameter of the tunnel was investigated. Furthermore, the ring building time for four tunnels with different sizes of diameters and a variety of ring arrangement were analyzed and the relationship between TBM diameter and segment installation time and consequently TBM utilization was evaluated.

Jun 13, 2021

By A. H. Baldo

Covers a very broad spectrum of problems and solutions. The problems are multitudinous and their solutions are sometimes simplistic, sometimes ingenious and sometimes within a very broad interpretation of the law. However, one thing is quite certain: the problems and their solutions will have a direct impact upon corporate and personal well being. First of all, why does one mine in a foreign land? Since the Bronze Age, when ancient man discovered the metallurgy of copper, tin and zinc, intrepid souls have been wandering afield searching for and exploiting those mineral deposits which would create wealth and security for his city-state or community.

Jan 1, 1981

John C. Greenway was responsible for much of my success in the seven years from what I called the end of my apprenticeship in exploration until I entered the Army in World War I. I first met Green- way on my return from Promontorio and, as he was replacing Powell, he was to be my boss. Even at first glance you couldn't help liking and trusting him. He was tall, well built, and erect-an old Yale athlete. After college he became a captain in the Rough Riders and a friend of Theodore Roosevelt, distinguishing himself in the Cuban campaign. He made good friends in all ranks of the Rough Riders, some later becoming leaders of industry and others following Greenway where-ever he went. After the Spanish War Greenway worked for iron mining companies around the Great Lakes and when the directors decided that Calumet and Arizona needed a new manager the ones who were also prominent in Oliver Iron Mining Co. selected Greenway It was a lucky choice for Greenway and for me. He became the best manager among those who ran the big copper mines He was open-minded in encouraging discussion and even opposition-until he made up his mind. Then, in military fashion, everyone must follow his decision without question. I think this is an essential of good management. Unfortunately a few did not feel this way and they had to leave. It was characteristic of those times that respect for the boss was so great that in the 16 years in which he was one of my best friends I, like all under him, always called him "Mr. Greenway." Soon after he arrived Greenway asked the leading mine operators in the southwest, Dr. Louis D. Ricketts and James S. Douglas, son of the Dr. James Douglas who had made Phelps Dodge great, to do special work for Calumet and Arizona. I found later that the object of the study was to determine the terms on which the half-dozen Warren District properties of Calumet and Arizona were to be joined in one

Jan 1, 1976

By Dae S. Young, Steven F. Hoerger

The geostatistical method of indicator kriging (IK) was extended to analyze two-dimensional distributions of rock joint orientations. The IK method provides a non-parametric approach for spatial analysis of local probability distribu- tions. By taking into account the spatial correlation of rock joint outcomes and the relative geometry between estimation unit and samples, the IK method provides optimum, spatially conditioned estimates. The estimation method was tested by comparing distributions of actual mapped rock joint orientations with their corresponding kriged estimates. The comparisons show the unbiasedness and accuracy of the non-parametric approach for estimating local probability distributions.

Jan 1, 1986

By William Paul Robinson

I would like to first summarize the relevant health information relating to the workers and general populations around uranium mining as a basis for understanding the hazards associated with these operations and their available remedies. This discussion will summarize the literature on Radon and its daughters, among the most toxic uranium decay products. Second, I will discuss waste handling in the uranium industry: past, present and future, discussing exploration, mining, and milling and the volumes of water and solid and gaseous wastes which are associated with these various phases of uranium operations. This paper will also include a discussion of the various past and present materials handling technologies and their responsiveness to the concern for uranium waste isolation. I will then conclude with a summary of recent modifications in the relevant standards as applied to uranium mining and milling. Joseph Wagoner, a research epidemiologist with the U.S. Public Health Service has summarized the literature on uranium mining and its health effects in his written testimony as a commissioned witness in British Columbia Royal Commission of Inquiry into Uranium Mining in January of 1980, entitled Uranium, The U.S. Experience: A Lesson in History.1 Briefly summarizinq his report, as early as 1546, miners of uranium bearing ores in Central Europe were reported to have unusually hiqh frequencies of fatal lung disease2. As early as 1879, the real nature of pulmonary disorders among these miners was first diagnosed to be malignant neoplasia or lung cancers. Of 655 miners dying between 1875 and 1912, 40% or 276 of these Central Europe miners died of lung cancer.4 By 1939, it was reported that lung cancer mortality rate for miners in these Central European mining districts was several times (9.7 per 1000) higher than that for similar populations in Vienna, Austria (0.34 per 1000). Thus, before uranium mining began in the U.S., there was a considerable body of information linking uranium mining to lung cancers. The U.S. experience can be summarized in Table 1 also from Wagoner's B.C. Testimony.1 This table shows that through 1978, 205 respiratory cancer deaths have been observed among white underground uranium miners in the

Jan 1, 1980

By K. H. McDaniel

This paper describes the development of a Windows-based interactive mine ventilation simulation software program at the Waste Isolation Pilot Plant (WIPP). To enhance the operation of the underground ventilation system, Westinghouse Electric Corp. developed a program called WIPPVENT. While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC from Mine Ventilation Services Inc. and uses the same subroutine to calculate airflow distributions, the user interface was completely rewritten as a Windows application with screen graphics. WIPPVENT is designed to interact with WIPP ventilation-monitoring systems through the sitewide central monitoring system. Data (e.g., air quantity and differential pressure) can be continuously collected from the underground ventilation remote-monitoring and control system and from the mine's weather stations (psychrometric data). Furthermore, WIPPVENT incorporates regulator characteristic curves specific to the site. The program utilizes this data to create and continuously update a real-time ventilation model. This paper discusses the design, the key features and the interactive capabilities of WIPPVENT.

Jan 1, 1997

By Susan G. Bilhorn

A number of studies have been conducted in active and inactive mine environments using continuous monitoring and data acquisition systems to detect various parameters. In addition to the information obtained for research purposes, these monitoring systems can provide a means to remotely collect required information (such as radon daughter concentrations and air velocity) and control various conditions (such as fan operation and air door position) in numerous working sections of an active mine. Selection of detector locations and placement, which are critical to obtain the information and control desired while not inhibiting mine operations and influencing the detector readings, are covered in this paper.

Jan 1, 1984

By Richard L. Sanford

The generalized rail haulage simulator described in this paper is an outgrowth of the need to expand a previously developed single level simulator to permit analysis of production problems where intermediate car storage is used. Many of the ideas of the former single level simulator, which is an integral part of an Underground Generalized Materials Handling Simulator (UGMHS), have been used in model development. In addition, experience gained in applying the earlier model to a variety of operating conditions has been heavily relied on. The generalized rail haulage simulation model can operate as an independent system and, as such, can be used to analyze rail haulage systems using production distributions as data input. In addition, this model is designed to replace the present rail haulage sub-assembly in the UGMHS model and the linking procedure has been integrated into the model. The flow of coal from production sections in UGMHS, for example, fill the mine cars and a condition of no empty cars at a loading station will shut down in by production systems.

Jan 1, 1974