Search Documents

By R. V. Ramani

Control is a vital management function by which operations are brought into compliance with predetermined standards to achieve the goals of an enterprise. Events that are characterized by a low degree of expectation, avoidability, and intent necessarily have a low degree of control. Such events are difficult not only to predict but to control as well. Fortunately, very few industrial situations fall into that category of events. It is an axiom of control technology that in order to control, one must first measure; further to measure, one must know the characteristics of the subject (or environment) upon which the measurement must be made. Finally, if measurements are to be made reliably, the influences that affect the measurement must be known and, if possible, understood. The complete control cycle therefore consists of the following: (1) defining the objective, (2) planning to achieve the objective, (3) putting the plan into practice with appropriate instructions, (4) measuring variables or parameters of interest, (5) transmitting and transforming the measurements to analyze the system's status and to predict the future outcome, (6) comparing these with the defined objective, and (7) determining and taking corrective actions to bring the actual results closer to the objective. The management principle underlying the control cycle is the principle of management by exception. The application of the principle and the frequency with which corrective actions are taken vary according to the purposes of the review and control. For example, the control of a machine operation (e.g., truck on a haul road) may require adjustments and therefore data, analysis, and decisions, in intervals of seconds whereas the review for ore-grade control may take several hours. Reviews, on the other hand, for cost control may be done in intervals of weeks or months. In any case, three specific purposes of the control cycle are: (1) to correct the operation so that it follows the accepted plan closely, (2) to evaluate the operation and predict future outcomes in light of changes in the environment or of more experience, and (3) to review the objectives and modify these to be reasonable and realistic.

Jan 1, 1979

By J. M. Smith, T. R. Horton, R. L. Blanchard, T. W. Fowler

INTRODUCTION Uranium mining operations release radioactive materials into both air and water and generate large quantities of solid wastes containing low levels of radioactive materials. Solid wastes produced by mining operations remain on the surface at many inactive mining sites in the Western United States. These mining effluents may present a potential health and environmental hazard. Therefore, Congress, in Section 114(c) of the Uranium Mill Tailings Radiation Control Act of 1978, instructed the Administrator of EPA to prepare a report identifying the location and potential health, safety, and environmental hazards of uranium mine wastes and to recommend a program to eliminate these hazards. Several facts and limitations helped shape the method and approach of the EPA study. Little information on uranium mines was available; measurement information that was available on uranium mine wastes was frequently influenced (biased) by nearby uranium mills; time and resources did not permit comprehensive field studies to provide additional data; and there are inherent variations between uranium mines and sites that complicate generic assessments of mine wastes. To accommodate these facts, the EPA developed conceptual models of uranium mines and made health and environmental projections from them. The models were based upon available data from the literature, supplemented with information from discussions with persons inside and outside the EPA, and by doing several short-term field studies in Texas, New Mexico, and Wyoming. When necessary, conservative (maximizing) assumptions were employed. This paper presents a brief account of a part of the EPA study dealing with the potential health and environmental effects caused by active surface and underground uranium mines. Airborne contaminants are emphasized, although solid and liquid effluents are also included. Due to the limited space, only the methods and parameters used and the results of the assessments will be presented here. Anyone interested in the source of the data used and the development of the parameters should refer to the EPA report (Blanchard et al., 1981). The occurrence and emissions of stable elements were included in the EPA report, however, due to space limitations and their apparent small impact, except for possibly at some specific mines, only radioactive sources will be included in this presentation. MODEL URANIUM MINES The model surface mine was located in the South Powder River Basin of Wyoming and the model underground mine was located in the Ambrosia Lake area of New Mexico. These are the prevalent type mines in those areas. The model mines were based on the average production parameters of the 63 open pit mines and the 256 underground mines that were operating in the United States in 1978 (Department of Energy, 1979) and on a report of an extensive study of open pit mines in Wyoming (Nielson et al., 1979). Information contained in environmental impact statements and in reports from federal and state agencies was also used. Parameters for the model mines are listed in Table 1. The surface mining scenario is that 7 pits are opened in the 17-year mine life with overburden from each successively mined pit used to backfill a previously completed pit, resulting in an equivalent of one pit of overburden (2.4 year production) stored on the surface. No backfilling is assumed at the underground mine. Overburden or waste rock, ore, and sub-ore are separated into separate piles that are either rectangular in shape with length twice the width or in the shape of a frustum of a regular cone. Both shapes have 45 degree sloping sides. To account for bulking, the volume of the material comprising the piles was considered to be 25% greater than the volume of material removed from the ground. It was assumed that dewatering was required at both mine sites. Wastewater discharge rates at the surface and underground mines were assumed to be 3.0 and 2.0 cu m per min, respectively. SOURCE TERMS The following radioactive contaminants at active uranium mines were assessed in the EPA report: 1. Radioactive particulates in a) wind suspended dust from waste rock (overburden) pile, sub-ore pile, ore stockpile, b) suspended dust from mining activities (rock breakage, loading and unloading ore and wastes), and c) vehicular dust, 2. Rn-222 emanation from waste rock (overburden) pile, sub-ore pile, ore stockpile, and mining activities, 3. Rn-222 emanation from mine surface areas, and 4. Radionuclides in wastewater discharged to land surface. Estimated average annual dust emissions (item 1 above) from the model mines are listed in Table 2. Emission factors and the assumptions used to estimate these dust emissions are described in detail in the EPA report. Radioactive source terms were computed for each of the sources; dust emissions were multiplied by the concentrations listed in Table 1

Jan 1, 1981

By Lucien Duckstein

The purpose of this paper is to give recommendations for utilization of water resources in a mining region, considering also water supply and environment; the case study of mining for coal and bauxite under the karstic aquifer of the Transdanubian mountain of Hungary is used to illustrate the approach, which consists in formulating a static multiobjective control model and solving it by compromise programming. The three activities of regional mineral resource exploitation, water supply and environmental protection are represented by different objectives which cannot be expressed in commensuerable units. Thus, a solution which is optimal for one objective is usually far from being optimal with respect to the other two objectives. As a result, we are not seeking an optimal solution for the conjunctive regional system, but a good compromise, trade-off or "satisfactum" (1), (2).

Jan 1, 1979

By Roger N. Kust

Because ammonia can form complex ions with certain of the transition metals, such as copper and nickel, it has long been of interest to extractive metallurgists interested in leaching or separating these metals. Although it is a relatively expensive reagent, ammonia is amenable to recycle because of its volatility. In development of processes utilizing ammoniacal leaching or separation schemes, information regarding solution vapor pressures, pH and solubility limitations is needed. There is voluminous literature on ammonia-water systems generated by the urea industry. However, frequently the systems of interest to metallurgists differ significantly in concentrations of ammonia used, the temperatures of interest. Furthermore, the differences arising from the presence of metal values in solution must be comprehended. There is surprisingly little information readily available regarding systems of practical interest to metallurgy. As a result, those interested in ammonia-based processes end up either doing expensive laboratory research to obtain necessary data or overdesigning the process. Another approach to obtaining desired information about ammoniacal systems is to attempt to calculate from first principles the various solution properties. This paper is being presented to illustrate what can be accomplished by estimating the state of equilibrium in an ammoniacal carbonate system from available thermodynamic information making simplifying assumptions when needed.

Jan 1, 1976

By Da-Rong Chou

An optimum method for selecting exploratory drilling locations has been developed. The process has been modelled as a highly non-linear programming problem subject to constraints. Solution involves an iterative algorithm which converges rapidly and procedures have been developed to distinguish between local and global optima. The algorithm has been implemented as an interactive computer program which allows the user to influence directly the solution process and to evaluate the effect of any manual adjustments to the optimal solution.

Jan 1, 1984

By S. Tafazoli, D. Cooper, I. Bell, S. Nouranian, B. Sameti, M. Ramezani

"Image-based rock fragmentation sensing in mines and quarries includes an important rock boundary delineation step, commonly referred to as rock segmentation. This paper presents an artificial intelligence-based solution to this challenge. The proposed technique encodes prior knowledge of previously analyzed images into mathematical/statistical models. Human-labeled images are used as inputs to train neural networks through an optimization process. The networks can then be used in real time for rock delineation. To build the models, special deep artificial neural networks are used as a pixel classifier. The proposed classifier labels each pixel (edge, rock or fine) by analyzing a plurality of pixels within the image. Advances in machine learning allow the network to contain many parameters. The increased number of parameters is a strong factor in the classifier’s ability to correctly classify each pixel. Deep learning-based segmentation, combined with 3D imaging followed by post processing, provides a unified fragmentation sensing solution. Results from automatic segmentation are compared to human labeled segmentation using the percentage passing curves for 64 rock images. INTRODUCTION Mines and quarries can see significant productivity and performance benefits by controlling material sizes (McKee, Chitmobo, & Morrell, 1995; Sellers & Gumede, 2012). During the past decade, image-based fragmentation analysis has been applied to estimate rock size distributions in order to optimize procedures in mines and quarries. Using a roving camera and operator assisted analysis Maerz, Franklin, and Coursen (1987) measured the size distribution of the blasted rock and eliminated the need for manual sieve analysis. Since then, many others have introduced automated and manual methods for fragmentation analysis and improved upon existing approaches (Girdner, Kemeny, Srikant, & McGill, 1996; Smith & Kemeny, 1993; Palangio, Palangio, & Maerz, 2005; Tafazoli & Ziraknejad, 2009; Raina, 2013). In image-based fragmentation, rock boundaries are identified in the image, and an image scaling is applied to transform rock pixel sizes into real world dimensions. Usually geometric references, such as regularly shaped objects (discs and basketballs) (Siddigui, Ali Shah, & Behan, 2009), or the known size of an excavator bucket (Zeng, Chow, Baumann, & Tafazoli, 2012), are used to determine the proper scaling factor. In recent years, 3D imaging and sensing have also been incorporated to improve rock delineation. Specific methods include using camera-laser combinations and stereo imaging to measure rock fragmentation on conveyor belts (Noy, 2013; Thurley, 2013; Dislaire, Illing, Laurent, & Pirard, 2013) as well as portable fragmentation analysis devices with 3D imaging sensors (Sameti, et al., 2014)."

Jan 1, 2018

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study was to investigate the influence of amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and organic acids (citric, malic, tartaric, fumaric, oxalic, succinic and ascorbic acid) on gold extraction from silicate ore. Use of amino acids to extract gold was preferred compared with organic acids due to the presence of carboxylic group and amine groups in amino acids. Among the assessed amino acids, aspartic acid and glutamic acid had higher capacities to extract gold due to their structures, which lacked aromatic rings and long side chains. Organic acids could also extract gold. In particular, oxalic and succinic acids had the greatest capacity to extract gold versus the other tested organic acids. Moreover, aspartic acid had a greater capacity to extract gold from ores than the same concentration of succinic acid. We confirmed the aspartic acid and succinic acid functional groups by Fourier transform infrared spectroscopy. The findings revealed that aspartic acid had a greater capacity to extract gold than succinic acid due to the presence of both amine and carboxylic groups (succinic acid contained only a carboxylic group). The optimal gold:aspartic acid molar ratio was 1:6 and low concentrations of aspartic acid extracted 35–42%of gold from silicate ore within 15 days. This can be used as an alternative to traditional methods for extracting gold from ore; it is non-toxic to human health and environmentally friendly.

Aug 10, 2021

By F. J. Menzer, E. M. Schern

The Morenci/Metcalf porphyry copper mining operation, located in southeastern Arizona, currently processes approximately 91,000 tonnes of ore per day and has copper ore reserves estimated to be in excess of one billion tonnes. Functional groups within the Geology Department (currently staffed with six professional and two support personnel) include mine geology, project geology, and hydrogeology. The primary task of mine geologists is daily preblast bench face mapping with grade and mill amenability estimates. Auxiliary duties include detailed in-pit metal distribution evaluation, mineragraphic work and flux quarry geology. Project geologists conduct exploration and preliminary development projects both within and outside the Morenci district and provide support to ore reserve block modeling and geotechnical work performed by the Morenci mine engineering group. Hydrogeologists handle exploration for and development of groundwater resources and groundwater flow modeling, mine dump leach solution penetration and recovery evaluation, and tailing dam water reclamation.

Jan 1, 1992

By J. W. Keck

Pilot plant grinding and concentration test results indicate that conglomerate native copper ore can be ground and concentrated using conventional techniques. Single stage autogenous grinding and rod mill-ball mill grinding required the same amount of energy far the required comminution. Metallurgical results were comparable for both types of grinding investigated.

Jan 1, 1973

By Y. A. Attia

A study was performed on selective flocculation and dispersion for ultrafine coal cleaning. A totally hydrophobic polymer, FR-7A, was employed as the selective flocculent for coal, sodium metaphosphate (SMP) as the general dispersant for shale and a synthetic polymeric product, polyacrylic acid-xanthate (PAAX), as the selective dispersant for pyrite. In the adsorption tests, nephelometry and spectrophotometry were employed for determining the concentration of FR-7A and PAAX in the solutions respectively. The adsorption tests indicated that: a) FR-7A has a higher affinity toward coal and pyrite than that for shale; and b) PAAX has a much higher affinity toward pyrite than toward coal and shale. In the selective flocculation tests, the ash-forming minerals can be efficiently rejected using sedimentation as the separation method. However, due to their relatively high specific gravity, pyrite particles co-settle with the coal flocs. To reject fine pyrite, a froth flotation was used for floc separation. The one-step flocculation-flotation process could reject more than 70% of each of the pyritic sulfur and ash minerals, while recovering more than 85% of the coal.

Jan 1, 1990

By Paul A. Rittenhouse

Its a pleasure to be with you this afternoon and to talk briefly on one of my favorite subjects -- the U.S. sulphur industry. As our Chairman mentioned, I have been associated with the sulphur industry either directly or indirectly for the last twenty years, both on the production side and as a consumer. Sulphur, while unseen and relatively unknown to most people, is like margarine ... that ubiquitous spread ... that is yellow and nearly omnipresent in the industrial world. It is because sulphur, in some form, is required in nearly all aspects of our economy that makes its study so interesting to me as a researcher. An analysis of the sulphur outlook requires examination of such industries as fertilizer, paints and pigments, copper and zinc, uranium, petroleum, chemicals, pulp and paper and textiles - just to name a few. Of course, because its use is so widespread and ever-changing it is difficult to develop and maintain a good understanding of the sulphur industry. It is also a problem to cover the industry in a short discussion and to project its really dynamic nature. Hut, if you will bear with me, I will attempt the task. First of all, let me say that sulphur today is a world commodity and to a large extent moves freely in world trade; nearly a third of the world's sulphur or something over 15 million tons in 1974 entered international trade. However, today our interest is in the current changing sulphur picture in the U.S., with particular emphasis on the western part of the country.

Jan 1, 1975

By Steven J. Schatzel, Kayode M. Ajayi, Zoheir Khademian

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine creating safety concerns. To provide recommendations for developing guidelines that ensure a safe co-existence of longwall mining and unconventional shale gas production, this study evaluates the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach using a discrete fracture network (DFN) model. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations is within values validated with field measurements. The results show that a decrease in fracture aperture (potentially due to longwall-induced stress in the likely vicinity of the breach location) reduces the potential gas flow to the mine by a significantly higher proportion. A 50% decrease in the aperture of the fracture that directly transports the gas from the casing breach location reduces the gas flow to the mine by over 70%. Similarly, changes in the fracture water saturation level significantly affect the gas flow. In all cases, the potential gas flow to the mine is higher if the casing breach occurs at an increased gas well pressure. These findings provide critical information regarding the impact of each of the parameters associated with gas flow in the event of a shale gas casing breach near a longwall mine and could help towards the development of guidelines to ensure a safe coexistence of both industries.

Sep 28, 2022

By S. J. Schatzel, K. M. Ajayi, Z. Khademian

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine creating safety concerns. To provide recommendations for developing guidelines that ensure a safe co-existence of longwall mining and unconventional shale gas production, this study evaluates the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach using a discrete fracture network (DFN) model. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements. The results show that a decrease in fracture aperture (potentially due to longwall-induced stress in the likely vicinity of the breach location) reduces the potential gas flow to the mine by a significantly higher proportion. A 50% decrease in the aperture of the fracture that directly transports the gas from the casing breach location reduces the gas flow to the mine by over 70%. Similarly, changes in the fracture water saturation level significantly affect the gas flow. In all cases, the potential gas flow to the mine is higher if the casing breach occurs at an increased gas well pressure. These findings provide critical information regarding the impact of each of the parameters associated with gas flow in the event of a shale gas casing breach near a longwall mine and could help towards the development of guidelines to ensure a safe coexistence of both industries.

Mar 2, 2022

By N. B. Aughenbaugh

Compacted clays are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials used for clay liners include a wide variety of sand, silt and clay admixtures that exhibit dramatically different engineering properties when densified. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Be-cause they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners must include an evaluation of their flexibility which is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1990

By J. Franko, M. S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium separation circuits. In this study, the performance of a continuous, laboratory wet-drum magnetic separator was evaluated both with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration and nonmagnetic material. The results indicate that, under certain conditions, the purity of the magnetic material increased after ultrasonic treatment. Key words: Ultrasonics, Wet-drum magnetic separation, Iron ore

Jan 1, 2003

By J. Moreno, P. Sinton, R. Vogwill

Groundwater models are often used to estimate and optimize dewatering volumes, locations, and rates, as well as water supply production for mines. Projections of future dewatering rates are highly dependent on the conceptual model used as a basis for the numerical model. This paper presents an audit of modeled dewatering rates versus actual data and an examination of the reasons for discrepancies. The setting is a gold mine, in a collapsed volcanic crater breached by the ocean. Mining will occur to about 200m below sea level within a remnant geothermal system. A detailed hydrogeologic investigation was conducted to support dewatering and geothermal depressurization design for future mining operations. These studies included development of a three-dimensional model to simulate heat and density-coupled groundwater flow, using software developed by URS/Dames & Moore. In this paper, the groundwater modeling results prepared 5 years previously by others was audited using operational dewatering data. This model was then extended using the new mine schedule and actual locations for dewatering wells to predict future dewatering requirements. In addition, a comparison between “hot” and “cold” model results was used to assess the need to use a heat-coupled versus a standard groundwater model for dewatering predictions.

Jan 1, 2003

By Z. Rogovin

In order to develop more accurate procedures for scale-up and design of semi-autogenous-grinding mills through detailed mathematical models, a better understanding of the charge motion and rock/ball segregation is needed. To achieve this a 0.61 m (2.0 ft) diameter x 0.305 m (1.0 ft) length plexiglas mill was constructed as a scale model of a commercial SAG mill. Rock motion in the rotating mill was simulated using various sizes of ceramic balls. Quantitative measurements of dynamic angle of repose, water and slurry motion, holdup and size segregation of the charge were taken. In addition, a video-presentaiton (available to the public) was prepared to elucidate charge and water motion at various mill speeds, charge volumes, rock size distribution and flow rates.

Jan 1, 1985

By J. A. Siekmeier

The thickness of the laminated beam modeled in this study is based on bridging potential and TDR measurements. The laminated beam stiffness is based on the effective stiffness of an equivalent transformed section. The maximum deflection of this near-surface laminated beam is compared with the maximum measured surface subsidence. The spreadsheet provides a rational technique to graphically display the character of the overburden and potentially allows prediction of a subsidence factor based on boring logs and the proposed mine plan. The U.S. Department of the Interior, Bureau of Mines (Bureau), utilizes a commercially available computer spreadsheet program in combination with a modified version of Bieniawski's Rock Mass Rating (RMR) system to characterize the geology overlying high extraction coal mines. The spreadsheet program calculates a RMR for each bed based on the lithology, thickness, and engineering properties, which are determined from boring logs and laboratory tests. Once the RMR is calculated the spreadsheet has two major functions. First, the spreadsheet calculates values used to graphically represent the character of each individual bed in the overburden. It calculates an in situ deformation modulus using an empirical rela¬tionship between the modulus and the RMR and then uses this effective modulus along with additional parameters that are based on mine geometry to calculate the bending stiffness and bridging potential for each bed. Second, the spreadsheet creates a transformed section that allows groups of beds to be modeled as an elastic beam. It then calculates a bridging potential for the entire rock mass. The bridging potential of the rock mass is a single value that takes into account both the geology of the overburden and the geometry of the mine. It seems reasonable that there would be a strong correlation between the bridging potential, the overburden response to high extraction mining, and the subsidence ratio. The results presented in this paper focus on the relationship between the bridging potential of individual beds and the deformation measured using Time Domain Reflectometry (TOR). Subsurface displacements measured over seven high extraction coal mines in southern Illinois were correlated with the bed stiffness and bridging potential profiles. Based on these correlations it was evident that the process of caving and subsidence over these high extraction mines involved momentary bridging by individual beds or groups of beds and the ultimate development of a laminated beam near the surface.

Jan 1, 1986

By John E. Tilton

Mining is one of the oldest human activities. It goes back at least to the Bronze Age and possibly even the Stone Age. The Romans mined copper in Spain and tin in England some two thousand years ago. The writings of Agricola in the 16th century show that mining was important in the Middle Ages. Today we mine more mineral commodities in greater tonnages than ever before. This long and fascinating history closely tied with the economic development of the human race is one of the charms of the mining industry. It also, unfortunately, gives rise to some widespread misconceptions.

Jan 1, 1997

By H. B. Charmbury

The acid mine drainage problem in Pennsylvania is of continuing and growing interest to the coal mining industry, the state government and the citizenry at large. Approximately one-third of the total volume of mine drainage presently polluting the streams of the Commonwealth originates from active coal operations and two-thirds come from ?abandoned mine discharges.? For this reason the Pennsylvania Department of Mines and Mineral Industries has mounted a significant research and action program seeking solutions to this two-fold problem. The Coal Research Board of the Department has sponsored a wide variety of research projects in an effort to study the treatment of acidic and highly ferruginous mine waters. A review of the published literature on the treatment of mine waters indicated that many laboratory and theoretical studies had been undertaken on various aspects of the coal mine drainage problem, but little applied, developmental, or engineering study had been undertaken. In January of 1964 the Board commenced a rigorous program using state and industry funds in an effort to find a ?least cost? solution or solutions to this vexing problem.

Jan 1, 1967