Search Documents

By Paul S. Parobeck, Robert A. Haney, Andrew J. Gero, Thomas F. Tomb

As a result of recommendations made in the 1988 Report of the Mine Safety and Health Administration Advisory Committee on Standards and Regulations for Diesel-Powered Equipment in Underground Coal Mines, the Mine Safety and Health Administration (MSHA) initiated a program to develop and test a diesel particulate sampling device. The sampling device employed the principles of inertial impaction to separate respirable dust into two fractions; one fraction containing particulate material having an aerodynamic equivalent diameter equal to, or greater than, 1.0 micrometer, and the other fraction containing particulate material having an aerodynamic equivalent diameter less than 1.0 micrometer. The design criteria were based on data which showed that virtually all of the diesel particulate material and very little of the mine generated dust was less than 1.0 micrometer in size. The instrument was tested in underground dieselized coal mines and in the laboratory. Comparative measurements were obtained with the MSHA designed impactor sampler, a University of Minnesota (UM) designed impactor sampler and MSHA's standard respirable coal mine dust sampler. Simultaneous measurements were also obtained with five of the MSHA and five of the UM designed impactor samplers to investigate between sampler precision. The paper discusses the design differences between the MSHA and UM impactor samplers, the precision of replicate measurement obtained with both instruments and compares measurements obtained with the respective samplers of the sub- and supermicron fractions of the respirable material.

Jan 1, 1991

By Donald D. Carr

Four counties in Indiana--LaPorte, Vigo, Vanderburgh, and Switzerland--have potential for deep underground limestone mining because they are in or are near high population areas and have no surface-minable limestone de- posits. The principal markets are Gary-South Bend, Terre Haute, Evansville, and Cincinnati. Minable seams suitable for aggregate are 120 to 150 meters (400 to 500 feet) below the surface in LaPorte and Vigo Counties, about 90 meters (300 feet) below the surface in Switzerland County, and about 600 meters (2,000 feet) below the surface in Vanderburgh County. Some deposits are also suitable for high-purity uses or for cement raw materials, which enhances their potential for exploitation.

Jan 1, 1980

By Clinton A. Hollingsworth

The Flotaire Flotation Cell is a simple, efficient hydraulic/pneumatic Flotation Cell that has no moving parts. It is normally used in conjunction with a surfactant (frother) in which case the combination is known as "The Flotaire System". On many ores, metallurgical efficiencies are substantially increased and operating costs reduce. For example, in floating phosphate rock, it is not unusual for BPL recovery to be increased more than 10%, the major increase being due to floating coarse phosphate, up to 14 mesh, and the difficult to float phosphate. Substantial improvements have also been made on coal, mica, vermiculite, kaolin, barite, copper, etc.

Jan 1, 1981

By Paul Dean Proctor

The world's population by 2000 A. D. may approximate 6.5 billion and the United States' 304 million. South Asian population increases between 1970 and 2000 A. D. will be triple the projected population of North America. Such anticipated dramatic and probably traumatic increases in world population yield grave concern for the standard of living in the world and the United States. The people of the United States currently consume 32 percent of the world's energy and similarly large percentages of the world's mineral raw materials. With only 6 percent of the present world's population and slightly smaller percentage by 2000 A. D., much expanded world-wide production of energy and raw materials will be required to maintain even a standstill living standard. A minimal 2 percent increase per year in the standard of living in the United States and a 4 percent increase elsewhere in the world, beyond the demands of the estimated population increases, suggest the magnitude of the increased need for energy-mineral raw materials and the possible crises the world will face in these areas by 2000 A. D. Mineral engineers and scientists with broad educational backgrounds will be required in greatly increased numbers to help alleviate, and possibly avert, expected energy-mineral raw materials shortages of the next millenium. Explorationists, mineral engineers, commodity economists, environmentalists, city, county, state, and federal mineral materials planners and coordinators, and metallurgists will be among those most needed. AIME membership in the second century of the Institute's history will contribute directly to this personnel pool.

Jan 1, 1971

By M. J. Laurila

The concentration of low grade iron ores to pellets or sinter fines suitable for blast furnace feed or direct reduction is highly energy intensive and costly in terns of both size reduction and separatory processes. Large equipment with high throughputs are required to make the fine grinds and multi-stage separations economical. Control of these circuits is essential to producing a high grade product. As a result, iron ore concentrators possess some of the more sophisticated instrumentation for process control in the mineral dressing industry. These instruments must characterize flowstreams of up to 8,000 gpm where 80% of the particles are less than 50 µm. The past decade has been one where enormous strides have been made in automated control of iron ore plants. This paper reviews state-of- the-art control systems for crushing, grinding, magnetic separation, froth flotation and sizing/classifying circuits. Trends toward computerization and plant automation in response to a dismal outlook for North American steel production are also examined.

Jan 1, 1984

By Thomas H. Ferrigno

Modern Plastics (July, 1983) reported that about 2.2 million tons of mineral fillers were expected to be consumed by the plastics industry that year, of which 7096 was limestone derived. The combination of fillers and polymers is called a composite and, in the more general sense includes continuous and discontinuous components in a matrix. The only significant technical advance in the fillers industry has been the greater general availability of surfied (Ferrigno 1959), an acronym for surface modified, fillers. The many reasons for this occurrence will be given in detail later, but the primary reason lie with differences between inorganic filler surfaces and the polymers which bind them together to form the composite. Minerals and glasses (fiberglass, fly-ash and beads) have surface tensions in excess of 200 dynes/cm, whereas organic materials have surface tensions less than 75 dynes cm. Water has a surface tension of 72 dynes/cm and is always present as an absorbed layer on high surface tension materials to reduce the surface tension. Although almost any organic liquid or polymer has a surface tension low enough to displace the water layer, the highly polar nature of filler surfaces requires highly polar agents to produce a permanent effect, and frequently the water is so tightly bonded or so much more active that the displacement is temporary. Furthermore; the water layer causes tiny particles to adhere to each other (agglomerate) to make sepaartion or dispersion of the individual particles very difficult. The solution to these problems is then to form a chemically bonded layer on the filler surface similar to that of the polymer so that immediate wetting, dispersion and uniform distribution of the filler particles is obtained.

Jan 1, 1985

By B. Denby, D. J. McMlarnon

During the ongoing research into the possible applications of Virtual Reality in underground operations, the AIMS Research Unit has developed a user-interface driven program which enables a user to input the geometry of underground mines, and add equipment and working processes in order to produce an accurate simulation of their operation. This paper describes the main features of this system (VR-MINE). Virtual Reality is a field which has grown out of three dimensional computer graphics techniques, and allows a user to move freely around a model held within the computer's memory. Movement around this model is carried out by the use of intuitive peripherals such as joysticks, with the user's view from their position within the model being produced in real time on a computer monitor or other device (such as a headset). This enables a user to interact with any three dimensional model and see the results of their actions immediately. VR-MINE is broken into two separate programs, both running under Microsoft Windows 3.1 or above. The first, the editor, allows the user to develop the mine layout and add equipment and personnel. The mine geometry is considered to be made up of various types of objects, for example a straight roadway segment which can be inclined, a junction roadway segment, and a turning segment. The geometry can then saved into a file to be loaded in by the second program of VR-MINE, the viewer. This generates a real- istic representation of the mine, with undulating floors and walls. It also has the ability to display multiple windows on the mine at the same time, which are arranged interactively. The simulation occurs within this program, with the user traversing the model in real time to examine possible areas of improvement in operations. This paper gives a number of examples of how the AIMS Re- search Unit has applied this technology to a range of underground mining scenarios to improve the safety of workers in the under- ground environment. The application discussed include computer graphics and Virtual Reality systems to training, risk analysis, visualisation, simulation, accident investigation and major hazard planning.

Jan 1, 1996

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

To provide critical scientific data and engineering guidelines to federal and state regulatory agencies as well as the coal and gas industries, the National Institute for Occupational Safety and Health (NIOSH) initiated a Gas Well Stability Research Program in 2016. This paper summarizes the critical scientific data acquisition, interpretation, and modeling by NIOSH regarding the stability of unconventional shale gas wells influenced by longwall mining. Currently, NIOSH is the only organization in the U.S. conducting such fundamental and impactoriented research, which receives input and collaborations from MSHA, PADEP, WVDMS, OHDNR, the coal industry, and the gas industry. Results from the NIOSH field instrumentation programs—which include surface, subsurface, and underground instrumentation—and the parallel three-dimensional numerical modeling programs indicate that, under shallow and medium covers, the measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Casing couplers are found to play an important role in longwall-induced casing deformations. Cementing alternatives are found to have significant impact on longwall-induced casing stresses and deformations. Measured 60-arm caliper logging results are in good agreement with three-dimensional computer simulation results. Engineering guidelines on longwall-induced deformations, casing and cementing alternatives, gas well setback distances, as well as risk assessment strategy are proposed.

Mar 2, 2022

By S. Chander

The effect of sample storage in argon and in air on kinetics of oxidation of pyrite from a coal source was studied using accelerated weathering test in laboratory columns. Prior to the weathering tests the samples were crushed, ground, and stored for various time periods in argon and air. The results showed a dramatic difference in the rate of oxidation of the aged samples. The differences were interpreted based on the hypothesis that the aging of pyrite led to the formation of surface coatings which changed with time. The significance of these results in pyrite/reagent interactions in flotation and in evaluating the acid mine drainage potential of pyritic waste materials is discussed.

Jan 1, 1993

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995

By R. H. Hanewald

The processing of EAF baghouse dusts from both the specialty steel industry and low alloy producers will be reviewed. In addition, the INMETCO process has been modified so as to recover nickel, chromium and iron from many other waste materials such as pickling solutions or filter cakes, spent nickel and chromium plating baths, carbon refractories from pickling tanks, and super alloy wastes including baghouse bags. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high temperature metals recovery. This, along with the details of INMETCO's BDAT Test Program and results performed to pre-agreed standards with the EPA will be discussed.

Jan 1, 1992

By Kuda R. Mutama, Allen E. Hall

A wind tunnel investigation into the fundamental characteristics of jet fan performance is described. The effects of varying fan positioning in a square tunnel cross section are reported for two fan outlet diameters and velocities. Tests were conducted, also for a jet fan placed in a flow developed by an external fan operating in the same direction as the jet fan. The position of the jet fan relative to the tunnel walls was found to affect its performance. Performance parameters were determined and used to formulate theoretical equations based on momentum and energy considerations. The results identified a range of flow ratios which can be used to design an effective jet fan ventilation system and provide a basis for the selection of jet fans for practical mining applications

Jan 1, 1997

By Osvaldo A. Bascur

Most mining and metallurgical plants have developed predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis, oil and lube analysis for critical equipment. Process control strategies have also been installed in several metallurgical sites. These control strategies require instrumentation maintenance from local personnel. The availability of real time and process history to identify the most critical part of the processing system from mechanical integrity is a must for global plant optimization. Specialized performance control monitoring algorithms are required to justify their existence and contribution to the bottom line. Emerging technologies are combining these techniques into a single total plant system. Tools are required to assist in troubleshooting and adapting these process control instruments and strategies. The key is the plant equipment and process control availability and utilization rather than just maintenance.

Jan 1, 1997

By Kenneth A. Pietila

The thickening and dewatering characteristics of refuse slurries are as variable as the coal mining operations and preparation plants that create them. This paper discusses these characteristics based on field studies at a number of mine sites. The connection between bench and full scale performance is confirmed with the design, construction and operation of an integrated 18m (60 ft) diameter thickener and 2.5 meter belt filter press system in Western Kentucky. The data from this system are presented.

Jan 1, 1984

By David Butts

Completion of a railroad to the high Tibetan Plateau in Central China has now made it economical to exploit its mineral reserves. Lead and zinc mines are now being established. A potash plant to produce 40,000 tons per year KC1 is now in operation. Plans to produce 200,000 tons per year by 1987 are being implemented. Pilot drilling for oil and natural gas have proved up reserves. Slaughter houses are being constructed to ship yak, mutton and beef from the endless grasslands on the plateau. Research Centers in Xining and Golmud have been completed for the sole purpose of increasing technology and exploitation of the Tsaidam Basin and surrounding area.

Jan 1, 1984

By R. J. Zagrocki

Rekindled public concern about lead toxicity has intensified the awareness of lead-bearing materials in contact with the environment and the human population. Lead's common association with other metals makes the increasingly restrictive lead standards a primary concern for a large number of metal and metal-related industries. In commercial scale demonstration tests with lead-bearing wastes, the HRD Flame Reactor process has a demonstrated ability to separate and recover over 95% of the lead as a recyclable oxide, while rendering the remainder of the material as vitrified, non-leaching, and nonhazardous co-product. Recent Flame Reactor process tests and preliminary cost data for secondary lead soda slag are highlighted.

Jan 1, 1992

By J. F. Abel, R. J. Spengler

Convergence measurement across the 17.4-m (57-ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 x 9.6 m (38 x 31.5 ft) inside diameter. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2.75 in.), and 5.7 cm (2.25 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1987

By F. Milton Lewis

Several alternatives are available for treating lover grade gold ores averaging 0.04 to 0.10 ounce per ton. These include heap, vat and agitation leaching and may involve conventional zinc precipitation or carbon adsorption-electrowinning systems. Each of these processes have their inherent economic and operating advantages and disadvantages and the selection of the optimum method for a given gold ore is solely based on economic evaluation of the applicable processes. In this paper an effort is made to provide engineering feasibility estimates for the above processes under varying operational conditions such as ore grade and price of gold.

Jan 1, 1974

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to develop a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 ppm WO3). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten vas recovered as a marketable iron-tungsten concentrate containing 44 percent tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process investigation unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By S. Tuylu, D. Adiguzel, A. Bascetin, H. Eker

"Tailings can be more stable in-site where they are stored and and so the risk of conventional tailings dam accidents can be reduced by alternative methods. In recent years, surface paste disposal (SPD) method is one of the alternative tailings storage methods. According to the results obtained from the previous lab scale experiments, optimum storage design was determined and then, this design was carried out in-site application under atmospheric conditions by a pilot scale tests. In the field study, two separate dams with no environmental hazards were established by the hazardous waste storage directive, whose surface area is measured as 400cm × 200cm. Also physical changes in the paste tailings were measured by the sensors such as volumetric water content, mutric suction and oxygen consumption. In addition, seepage water was collected in the drainage pool and examined for acid mine drainage and metal mobilization risks. As a result of the preliminary data obtained from measurements of pilot scale tests, when the pH value of seepage in the cemented dam (only 1th and 10th layers with cemented) is about 11, the pH value of seepage in the uncemented (reference) dam is measured at 8-9. INTRODUCTION Environmental damages occurred during the deposition of mine process tailings at surface using conventional methods (tailings dam etc.) can be reduced and/or eliminated with the use of new technologies and methods to an important extent. Nowadays, it has been investigated to safely deposit metal mine wastes generally discharged into surface tailings dams, seas, rivers, creeks etc. using Paste Tailing Technology which gains the growing importance in recent years. Meanwhile, Paste Tailings Technology has two applications in industry as an underground paste backfill and surface paste deposition. Particularly scientific studies about deposition of process tailings as paste sample in underground and surface have been increased. These studies showed that surface paste deposition can minimize the free water amount which is the biggest problem in conventional tailings dams. Additionally, it also provides less particle segregation, in other words, the formation of more homogenous material, the development of geotechnical properties which causes to obtain more stable material, increases the strength and stability of the paste with addition of binder where necessary surface paste material, and reduces the risk of Acid Mine Drainage (AMD) (Bascetin et al., 2017a). Theriault et al. (2003), Martin et al. (2006) and Simms et al. (2007) reported that Bulyanhulu mine in Tanzania is the first gold mine to employ surface paste disposal (SPD) worldwide. Here, tailings are deposited alternately via several towers. The tailings flow away from each tower to forming a conical deposit. Each layer had a lower thickness than 30 cm. The fresh tailings were poured on top of drying and hardening layer after a waiting period of 5-30 days. No cement was added into the tailings to prepare paste material. Uncemented paste was deposited by a solid content of 73% which corresponded to a 250 mm slump cone height (Yilmaz et al., 2014). In a study conducted by Yilmaz (2010) illustrates the preliminary results of a field cell testing undertaken to investigate the effect of in situ climate conditions and material properties on the performance and quality of fine-grained, sulphide-rich paste tailings at the LaRonde mine in Quebec, Canada. A total of two field cells are constructed in the surface disposal site of the mine and categorized as cemented cell CC and uncemented cell UC (Bascetin et al., 2017b)."

Jan 1, 2018