Search Documents

By W. T. Walter

High-G centrifuges from five preparation plants were sampled to determine and quantify the various operating factors affecting performance. The operating factors that were considered include feed rate and percent solids, size of feed material, screen-basket type, hardness of coal and age of the flights. The performance parameters that were measured include product surface moisture, recovery and degradation of the coal. Regression equations with good significance levels were developed.

Jan 1, 1982

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A three-stage fluidizing-bed process consisting of chlorination, selective oxidation and sulfur chloride conversion was tested for processing chalcopyrite concentrate. It was found that the use of excess oxygen was essential for the stable operation of the oxidation reactor. The excess-oxygen gas inevitably causes the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and selective oxidation steps with separate flow paths of the fluidizing gases, thereby, preventing the passage of excess-oxygen gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratoryscale fiuidizing bed setup.

Jan 1, 2002

By David M. Spatz

Ore deposit models are defined largely by physical geologic features that relate conveniently to remote sensing. New Landsat, SPOT, RADARSAT and other multispectral and hyperspectral sensors with improved spatial resolution are currently in development. Near-infrared and thermal airborne hyperspectral scanners hold outstanding promise for both mineral exploration and feasibility stage mapping at potential new mining projects. These scanners are capable of identifying silicification, differentiating silicate alteration types, and mapping compositional variations within igneous and metamorphic complexes. Research in 'mineral and rock spectrometry is helping to advance applications of remote sensing. Hyperspectral scanners are capable of differentiating compositional variations within individual mineral species. Innovative data processing techniques continue to enhance computer software applications and facilitate imagery analysis by the geologist. Today, . remote sensing imagery is commonly integrated with multiple data sets in GIS format to form the core data base for regional exploration programs.

Jan 1, 1995

By David Beck, Eko Wibowo, Hendri Silaen, Andres Sugiyanto, Karl Llewelyn

PT Freeport Indonesia’s Deep Mill Level Zone mine is one of the deepest block cave mines in the world and is in mountainous terrain in West Papua, Indonesia. The mineralization is hosted in a skarn deposit in a structural setting that is complex at the footprint, mine and regional scale. Large seismic events and significant episodes of rapid rock mass deformation are potentially critical geotechnical risks during this ramp-up stage of mining. Understanding the interaction between stress, strain, rock mass strength and geological structures is essential to minimize the hazard and engineer control measures to help ensure the safety of the employees while achieving production targets. This paper discusses how the seismicity and excavation damage have been shaped by the interactions between the mine and geological features, and how this affects strategic mining decisions. Additionally, the paper presents a summary of the mitigation measures used for mining the DMLZ in the safest and most productive way. These include improvements to geotechnical characterization of rock mass and structure, dynamic ground support designs, production scheduling for desirable cave propagation and a seismic monitoring system with re-entry protocols.

Apr 26, 2022

By John B. Goddard

The discovery of rhenium on the ion exchange resin used at the uranium in-situ leach operations at Palangana (Texas) led to a laboratory study on the possible methods of recovery. Rhenium, present in small amounts in the ammonium carbonate leach liquors as the perrhenate anion, Re04-, concentrated on the anion exchange resin, which was a factor of ten more selective for rhenium than for uranium. Various elution systems were investigated for stripping the rhenium from the columns after the uranium had been eluted with chloride or nitrate solutions. Although the perchlorate ion was most efficient on a molar basis, nitrate ion combined the benefits of efficiency and low cost. A 3[N] or stronger concentration of nitrate containing up to 0.5[N] H+ was found to be the system of choice. A rhenium sulfide concentrate containing up to 14% Re was obtained from these effluents by hydrogen sulfide precipitation. Preliminary experiments were run to produce rhenium metal powder by oxidation of the concentrate to NH4Re04 followed by hydrogen reduction at elevated temperature.

Jan 1, 1982

By David Lynn Passmore

The reliability of mine operators reports to the Health and Safety Analysis Center of the U.S. Deparetment of Labor of days lost from work by injured miners is .267.

Jan 1, 1985

By Joe B. Rosenbaum

Fine-sized mineral wastes discarded by ore milling plants require stabilization to prevent air and water pollution. Methods devised for achieving this stabilization include physical, chemical vegetative, and combination procedures. Although vegetative reclamation is preferred to physical and chemical stabilization, it is difficult to achieve because the wastes are sterile, contain deleterious inorganic salts, and lack the essential nutrients and physical characteristics required for sustaining vegetative growth. Nevertheless, recent research has developed methods for producing vegetative growth on all but excessively acidic, basic, or saline tailings at costs ranging from $100 to $650 per acre. This report summarizes effective procedures developed for vegetating average tailings, the cost differential between the various methods, and suggests procedures that may be applicable for achieving stabilization of pyrite-containing wastes that may oxidize and become excessively acidic. The use of buried layers of sewage sludge to prevent this acidification is discussed.

Jan 1, 1972

By R. Hogg

The sedimentation and dewatering characteristics of flocculated slurries are determined by the size and density of the flocs. Studies of the formation and growth of flocs reveal that floc size is limited by breakage of the agglomerates due to shear in the suspension. Floc density measurements indicate that there is an inverse relationship between size and density. This relationship appears to be determined primarily by the nature of the solid particles, especially the size distribution, but it appears that agitation of the suspension can lead to some densification of the flocs, in addition to breakage. It follows that both size and density can be controlled to a significant extent by regulating the physical conditions (agitation, method of flocculant addition etc.) during flocculation. The use of physical floc conditioning to control the sedimentation and dewatering (filtration) behavior of flocculated, fine-particle suspensions is evaluated in terms of its effects on floc size end density.

Jan 1, 1986

By M. K. Boateng, K. Awuah-Offei

"Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. The results show that the model is much more sensitive to the probability of imitation than the other two parameters. Thus, to reduce uncertainty surrounding the model’s predictions of community acceptance of mining, mines need to obtain accurate estimates of the probability of imitation. INTRODUCTION Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. AGENT-BASED MODEL OF COMMUNITY ACCEPTANCE A few researchers have started using agent-based models to study mining systems (Fujiono 2011; Nakagawa et al. 2013; Bahr 2015; Boateng and Awuah-Offei 2017a, b). Nakagawa and co-workers used ABM to evaluate dynamics of a mining project’s stakeholder networks whereas Fujiono used ABM to study innovation diffusion in the mining industry. Our previous work has presented models and a framework for modeling information diffusion in a mining community and its impact on level of acceptance (a measure of SLO) of the mining project (Boateng and Awuah-Offei 2017a, b)."

Jan 1, 2018

By E. R. Hoskins

The Gulf Coast States ranging from South Texas to Alabama contain vast resources of lignite ranging in energy content from about 4000 to 7000 Btu/lb (as-received) with sulfur content ranging from about 0.5 to 2 percent. Currently, the strip mining rate is about 35 million tons per year in Texas and essentially zero in the other Gulf Coast states. Estimates of future mining rates are as high as 310 million tons per year by the year 2000 with 240 being in Texas. In this paper, we examine the life cycle of the surface mineable lignice based on the most recent estimates of surface mine recoverable resources with two scenarios. The first indicates that a 310 million tpy rate could be sustained for only 15 years while the second scenario suggests that the 310 million tpy could be sustained for 25 to 30 years. If lignite resources are required beyond those that are surface mineable, the deep basin lignite will be developed. Five strategies for developing deep basin lignite are discussed.

Jan 1, 1983

By R. V. Ramani, K. V. Raj

"The air flow problems in open pit mines are complex. Computational fluid dynamics (CFD) models provide a detailed knowledge of the airflow pattern and velocity distribution, temperature, and pollutant concentration within an enclosed domain of the open pit. A range of turbulent model can be selected for varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithm they use; as a result, prediction varies from model to model. This paper presents a study of pollutant transport in an actual open pit mine under stable boundary layer. The objective is mainly to test two turbulence models using the same input conditions, model constants, and similar geometry. Measured data are used to compare results of the two CFD models, namely, the kappa-epsilon (?-e) model and the Large Eddy Simulation (LES) model. Despite the complex synoptic situations, different meteorological input data and the fast changing conditions, the simulation results from both the models are in good agreement regarding the dispersion of pollutants.INTRODUCTION Modeling of contaminant transport under Arctic air inversion is an important step for an assessment of the amount of pollutants within the open pit. The Airflow in open pit mines is of larger scale and does not follow the principles of pipe flow. The air flow problems in actual open pit mines are thus far more complex. CFD models provide a detailed knowledge of the airflow pattern and air velocity distribution, temperature, and pollutant concentration within an enclosed domain of an open pit. There is no known application of CFD in three-dimensional modeling of air flow in large open pit mines. Two equation RANS kappa-epsilon (?-e) and Large Eddy Simulation (CFD) models, however, have been developed to solve the stable boundary layer (SBL) problems in Atmospheric Sciences (Baklanov 2000, Basu and Porté-Agel 2006, Dop and Axelsen 2007, Bandopadhyay et al. 2014). Because an exact flow situation in open pit mines is not known a-priori, it is therefore, necessary to investigate various turbulent models to identify the appropriate model that would simulate the flow phenomena with reasonable accuracy, and predict the contaminant distributions within the pit. Dispersion models differ in their assumptions and structures as well as in the algorithm they use and, as a result, predictions vary from model to model. Furthermore, it is also important to investigate the behavior of a CFD model in simulating a complex phenomenon such as the transport and distribution of contaminants in open pit mine under Arctic air inversion. The simulation of an enhanced period of turbulence in SBL is of particular interest because traditional air pollution dispersion models cannot explicitly treat such intermittent events, and yet the SBL is often the worst-case scenario in an open pit pollution transport"

Jan 1, 2015

By Peter Zhang, Daniel Su, Heather Dougherty, Jack Trackemas

"Longwall mining has a significant influence on gas wells located within longwall chain pillars. Subsurface subsidence and abutment pressure induced by longwall mining can cause excessive stresses and deformations in gas well casings. If the gas well casings are compromised or ruptured, natural gas could migrate into the mine workings, potentially causing a fire or explosion. By the current safety regulations, the gas wells in the chain pillars have to be either plugged or protected by adequate coal pillars. The current regulations for the gas well pillar design are based on the 1957 Pennsylvania gas well pillar study. The study provided guidelines for gas well pillars by considering their support area and overburden depth as well as the location of the gas wells within the pillars. As the guidelines were developed for room-and-pillar mining under shallow cover, they are no longer applicable to modern longwall mining, particularly under deep cover. Gas well casing failures have occurred even though the chain pillars for the gas wells met the requirements by the 1957 study.This study presents seven cases of conventional gas wells penetrating through longwall chain pillars in the Pittsburgh coal seam. The study indicates that overburden depth and pillar size are not the only determining factors for gas well stability. The other important factors also include subsurface ground movement, overburden geology, and weak floor, as well as the construction of gas wells. Numerical modeling was used to model abutment pressure, subsurface deformations, and the response of gas well casings. The study demonstrated that numerical models are able to predict with reasonable accuracy the subsurface deformations in the overburden above, within, and below the chain pillars, and the potential location and modes of gas well failures, therefore providing a more quantifiable approach to assess the stability of the gas wells in longwall chain pillars.INTRODUCTIONIn the eastern United States, abundant gas wells have been drilled through coal seams that are being actively mined by longwall mining. The existence of gas wells in the U.S. coal fields, whether active or abandoned, have caused many issues for longwall mining. First of all, any gas well in the mining area has to be located by all possible means. Secondly, the gas wells within longwall panels have to be plugged, as cutting through gas wells will allow natural gas to flow into the active longwall mines. On the other hand, the gas wells within longwall chain pillars or barrier pillars can be left in place if the wells are protected by properly designed pillars."

Jan 1, 2019

By W. Miles

Introduction From a historical perspective, bentonite is the common rock term for various uses and applications. Its name originates from water-based muds near Fort Benton used for lubrication of wagon wheels during the 19th century migration to western territories (which are presently part of the United States) when the pioneers ran out of axle grease. From a clay mineralogy perspective, bentonite is composed primarily of montmorillonite, an expandable magnesium aluminum silicate clay mineral. When magnesium occupies an octahedral structural site that usually contains an aluminum atom, a negative charge is created. In order to neutralize negative charges, cations are drawn to the interlayer surfaces between clay mineral sheet structures. Modern applications for bentonite depend on the sodium or calcium cation populations and other characteristics of the clay mineral. When sodium is the dominant cation, the material is also called sodium bentonite, also known as swelling bentonite, western bentonite or Wyoming bentonite. When calcium or magnesium is the dominant cation, the material is called calcium bentonite, also known as nonswelling bentonite or southern bentonite. Swelling bentonite is recognized for its rapid hydration of interlayer sodium and subsequent dramatic expansion up to more than 20 times its original volume. Low shear can then disperse the hydrated sodium bentonite to form suspensions that increase viscosity and suspend solids. However, when shear is subsequently eliminated a sodium bentonite slurry gels. Characteristically, nonswelling calcium bentonite has relatively poor hydration properties and thus low expansion of the clay mineral. When subjected to low shear, calcium bentonite exhibits very little viscosity and poor suspension. Additionally, when shear is subsequently eliminated no more than minimal gelling takes place. The domestic and export markets related to both swelling and nonswelling bentonite are discussed below.

Jan 1, 2007

By Dan Plazak

The authors are to be congratulated for presenting a simple and practical tool for quick estimates of ground water flow rates. At the risk of detracting from the simplicity of the method, I would like to suggest a slight refinement to the equation as presented. As the authors noted, the Jacob-Lohman equation (1952) assumes confined-aquifer conditions. To use confined-aquifer equations in water-table aquifers, Jacob (1963) presented a correction to convert water-table aquifer drawdowns [ ] to equivalent confinedaquifer drawdowns [ ]:

Jan 1, 1994

By C. E. Jordan

The fundamental characteristics of ultrafine chalcopyrite flotation were investigated by the Bureau of Mines to establish techniques to improve recovery of ultrafine chalcopyrite. Intense agitation during conditioning was found to improve flotation recovery of the ultrafine chalcopyrite. A split-circuit flotation design, treating the plus 38-µm-size ore by the conventional method and treating the minus 38-µm-size ore with intense agitation conditioning followed by flotation, recovered 95.6 pct of the copper in a 28.3-pct-copper concentrate, This was a 5-pct increase in copper recovery over the conventional chalcopyrite flotation method.

Jan 1, 1986

By Nick A. Hasenack

A full survey of the laboratory and blast-furnace tests on 2 types of acid pellets is given. From the laboratory tests, carried out in an atmosphere containing hydrogen, it appears that type B, produced out of 100% magnetitic ores, has a far better low temperature disintegration index and a lower reducibility index than type A, produced from a hematite/magnetite mixture. The swelling index, chemical composition and mechanical properties of both types of pellets do not differ significantly. From the blast-furnace test, carried out with a burden consisting of 45% of pellets and 45% of sinter with basicsty ratio about 2.2, and at constant driving rate, it follows that there is no significant relationship between the disintegration value of the pellets and the blast-furnace permeability. If also is concluded that the lower reducibility of the type B pellets leads to a significantly higher coke consumption.

Jan 1, 1975

By R. C. Berry

The Environmental Impact Statement (EIS) has become a routine requirement for mining operations on federal lands. A similar document is being required in developing countries. Baseline studies are needed prior to writing an EIS and these studies involve surface water, groundwater, air quality, and wildlife/ native plant evaluations. The required baseline hydrology and geochemical studies are often the most expensive and lengthy evaluations. This paper summarizes the hydrology and geochemical baseline studies required for .An EIS and presents suggested methods to expedite these studies and to shorten the time and the cost to complete the studies and the EIS.

Jan 1, 1999

By M. Canty

Results are presented that were gathered during pilot-and field-scale testing of an innovative technology, sulfate-reducing bacteria (SRB), designed to treat and control acid mine drainage (AMD). The project was performed under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy through an Interagency Agreement. The MWTP is implemented by MSE, Technology Applications, Inc., located in Butte, Montana. Sulfate-reducing bacteria, a common group of anaerobic bacteria, produce hydrogen sulfide and bicarbonate when supplied with sources of carbon and sulfate. Hydrogen sulfide reacts with metal ions in AMD, precipitating them as metal sulfides; the bicarbonate serves to help neutralized the drainage. Pilot-scale testing was performed within eight packed-bed reactors at a temperature representative of a field application of this technology in a northern climate, nominally 8°C. The reactors, packed with an organic substrate, were operated continuously in upflow configurations receiving AMD at a flow rate corresponding to a 5-day retention time over a test duration of 60 days. During this time, numerous physical and chemical parameters were monitored. Pilot-scale metal removal efficiencies reached 99% for zinc, 99% for aluminum, 96% for manganese, 98% for cadmium, and 96% for copper. Iron and arsenic removal was not as effective as the aforementioned metals, which was largely attributed to the high levels of iron and arsenic contaminating the organic substrate. Evidence existed that both adsorption and sulfate reduction were occurring within the reactors.

Jan 1, 1998

By Bruce D. Hanson

A computer model capable of simulating the basic production system in a variety of underground mining methods has been developed at the Twin Cities Mining Research Center. This Bureau of Mines paper describes the simulation of the basic production system at the working face, which includes drilling, blasting, mucking, and roof bolting. The model is event-oriented; that is, the status of the system is updated at the occurrence of an event. All event or activity times, including failure and repair of equipment, are treated as stochastic variables. A location dimension, in addition to the time dimension, is used, allowing the simulation of multiple location systems. To aid the user in determining the efficiency of his system, the model provides several reports. An event or activity report gives the frequency of occurrence total active time, and cumulative delay statistics for each event. An equipment report delineates the availability and utilization of all equipment. A production report provides information on various performance measures such as tons produced and holes drilled. The cost report gives the cost of various elements in the system. Operating data from an actual mining situation were used in validating the model. In addition to the description of the model, examples of simulation experiments which were performed on a room-and-pillar mine system are given. Use of the model to determine methods for improving the efficiency of the system is discussed.

Jan 1, 1974

By Dani Delaloye, Kas Zurek

Evaluating and selecting the appropriate excavation method is a key to the success of any tunnelling project. The benefits and risks of different methods should be well understood by the designer and communicated to the project owner to enable selection of a preferred method from a technical, social and environmental impact, cost and constructability perspective. For tunnels that have an internal diameter around 3 m, depending on the tunnel purpose and ground conditions, both microtunnelling with pipe jacking and tunnel boring machine excavation with a one- or two-pass lining may be feasible construction methods. Using the Ferry Road and Riverbend Combined Sewer Relief Project located in Winnipeg, MB as a case study, this paper will discuss the benefits and drawbacks of each method, including technical design, social, environmental, cost, schedule, and risk considerations.

Jun 13, 2023