Search Documents

By Dennis K. Mortensen

Improvements in flotation technology are continually being made in the attempt to achieve the mineral processor's goal of maximum mineral concentrate grade and recovery at zero cost. Technology that cannot be totally proven in the laboratory must be tested under plant conditions either in a pilot plant or in the existing circuit. Problems associated with new technology can be solved effectively by the mineral processor who approaches each of the problems objectively.

Jan 1, 1989

By J. Kemeny, R. Fuentealba, C. Rodriguez, F. Fernandez, M. Rocha, T. BoBo

"Mathematical modeling in conjunction with mineral characterization is widely used as a method for design and optimization of comminution circuits, to simulate the processes of crushing, grinding and classification. An important input parameter to the simulation models is the Run-of-Mine Particle Size Distribution (ROM PSD). The run-of-mine size distributions due to blasting have a great influence on the performance of a semi-autogenous grinding (SAG) mill. In this paper, a mine case study was conducted where there are four primary geologic units and the material properties between the four units vary considerably. Also, the mixture of the four unit that will be mined at any given time also vary considerably. This presents a challenge in terms of optimizing the blasting for mill production throughout the mine life. As part of the case study, field rock mass characterization, laboratory rock mechanics tests, and laboratory breakage tests were conducted. The field characterization and rock mechanics tests provide material properties used to simulate the effect of different blast designs on run of mine particle size distributions (ROM PSD). The JKSimBlast software was used for these simulations. The rock breakage tests provide material properties used to simulate crushing and grinding performance. The JKSimMet software was used for these simulations. The goal of the mine is a mill throughput of 95,000 tonnes (104,720 tons) per day (TPD). Based on this goal, run-of-mine fragmentation analysis was conducted for four blasting designs resulting in powder factors of 0.44, 0.54, 0.64, and 0.94 kg/t. The powder factor of 0.44 represents a standard blasting design, while the 0.54 and 0.64 kg/t designs are high-energy blasts specifically to assist with mill production. The 0.94 kg/t design was investigated for the one geologic unit with very high strength. The results of the run-of-mine fragmentation analysis was then input into a crushing and grinding simulation model to predict the mill throughput for the time periods of 1-5 years and 6-10 years. The results indicate that certain blast designs are able to achieve the 95,000 tonnes TPD (104,720 tons TPD) goal, while other blast designs were not. A standard blast design with a 0.44 kg/t powder factor, for example, was not able to achieve the throughput goal, while a design with a 0.64 kg/t powder factor was able to achieve the goal in both the 1-5 and 5-10 year time periods. INTRODUCTION In recent years, mathematical modeling in conjunction with mineral characterization has been widely used as a method for the design and optimization of comminution circuits. The Run-of-Mine Particle Size Distribution (ROM PSD) is a function of rock properties and design parameters of the blast and has a significant impact on the crushing and grinding treatment circuit. Traditionally, design of the grinding treatment is estimated using only the F80 value instead of the full distribution of sizes in the feed, but the finer sizes have great influence on the treatment of a grinder, particularly in the SAG mill."

Jan 1, 2015

By A. Dadgar, R. H. Sergent

Changes in the ore types available and increased environmental concern have created a demand for an alternative technology to cyanide for the extraction of gold from ore. Great Lakes Chemical Corporation (Great Lakes) believes that halogen chemistry, in particular bromine chemistry, is the best available alternative to cyanide for gold extraction. Great Lakes is a Fortune 500 chemical company with sales of approximately one billion dollars per year. Great Lakes extracts elemental bromine from naturally occurring brines in Southern Arkansas. Great Lakes has developed a family of proprietary bromine compounds to aid in the extraction of gold. In addition to proprietary bromine compounds for gold extraction, Great Lakes has developed a method of recycling bromide ion in the leach circuit. Various recovery methods, including ion exchange and solvent , extraction are currently being studied.

Jan 1, 1990

By R. V. Ramani

In 1970, of the 603 million tons of coal produced in the United States, 339 million tons, or 56%, were produced by under- ground mines. While the ratio of underground to surface production has been decreasing in the last few years, it is anticipated that a 60:40 ratio of underground to surface-mined coal will remain for some time. Underground coal operators are continuing to invest in new mines and are interested in increasing the efficiency of all their operations. One area for improvement is in mine planning and design, particularly in the area of selection of equipment for operation. Because of the availability of a wide variety of equipment, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, such a choice must be made on the basis of technological facts and forecasts related to the mining operation. If the mining conditions can be reasonably predicted, along with a mining plan, it should be possible to insure the selection of the right equipment for the particular application. In order to increase the efficiency of underground coal operations, it is necessary to understand not only the operating system in detail, but the inter-relationships between system components and the operating environment. With such an understanding comes the application of simulation and other operations research techniques to plan and operate mining systems. Computer simulation studies have been successfully adapted to underground coal mining, and applications by Prelaz et al. (1965), and Manula and Sanford (1969) are some that are being used by the mining companies. However, a need still exists for better understanding of certain intra-system and system-environment interactions in order that computer simulation programs may be provided with better input data for more effective application. This paper deals with one aspect of the coal-winning system in need of better definition, namely, studying the performance of continuous miners.

Jan 1, 1973

By James E. Monsees, Wayne A. Carbiener, Michael R. Wigley

This paper illustrates an approach to quantitatively document the degree of technical conservatism to be incorporated into the design of a waste isolation system in bedded salt. It is anticipated that for an actual repository site the key performance constraints and/or design bases identified in this paper will be reviewed, and modified or supplemented as required. Ultimate acceptance of a repository will be dependent upon scientific peer input and scrutiny of the demonstrated conservatism inherent in each specific repository site and design.

Jan 1, 1981

By Richard L. Patterson, Alan P. Finch

Twenty years ago, when tunnel projects in the UK were generally procured by the public sector, many were completed late and over budget. Now a significant proportion of new infrastructure is developed by the private sector. Seeking more certainty in cost and programme, promoters have tried new and radically different methods of procurement and contract forms. The paper will review these developments, then examine the approach adopted for some of the largest current UK tunnelling projects (both in the public and private sectors) including the Channel Tunnel Rail Link, the Heathrow Terminal 5 Development and new highway tunnels.

Jan 1, 2003

By Konrad J. Banaszak

At least for the time being, these seems to be general but not universal agreement that Mississippi Valley type ore deposits formed entirely or in major proportion from heated connate brines (e.g. 1) Even with that agreement, major questions remain. I will present a coherent geochemical model and look at alternative views in the context of that model. The pattern of the following discussion is 1) the general geochemistry of the ore fluid, 2) the density-temperature relations and possible mechanisms of flow of those fluids, 3) the mechanisms of transportation and deposition of the ore minerals, and 4) a summary of a coherent model of genesis. The data equivocally define much about the deposits. The answer is still elusive.

Jan 1, 1979

By D. R. Forshey

Although the United States has the world's largest coal reserves, most of those reserves will require underground mining. Unless underground injury and fatality rates are reduced, the number of disabling injuries and accidental deaths will grow as coal production increases. The Bureau's Mining Research Program, designed to reduce the exposure of workers to hazards while improving productivity, is described. Major program thrusts are 1) re- moving the hazards or removing miners from the areas in which hazards exist, 2) developing ways to improve management decisions and mining skills so as to reduce the incidence of situations requiring human involvement in hazardous, emergency, or corrective tasks, and 3) improving, or at least maintaining, productivity so that both the tangible (dollar) and intangible (human) costs are reduced. In these ways, projected demands for coal can be met using resources without an increase in human suffering.

Jan 1, 1987

By Robert Stefanko

The most perplexing problem that has confronted mining engineers since the dawn of mining has been strata control. For the purposes of this paper, strata control will be defined as control of ground in the immediate area surrounding the, mine opening. To prevent movement of the surrounding strata into underground mine openings, miners have traditionally relied upon some type of artificial supports placed within the openings and located in a manner determined by trial and error from previous experience. Without the means to measure changes of stress in the supports and within the mine structure itself, an evaluation of the efficiency of the supports and mining system was impossible. Strata control thus remained an art with very little application of science. During recent years a revolution has occurred in mining. The modern mining engineer is contented no longer-with trial and error methods but is utilizing all the technological information at his command to obtain a solution to this age old problem. However, serious problems have arisen due to the lack of certain basic knowledge in three important areas: 1, The original stress distribution within the earth strata prior to mining. 2, Redistribution and concentration of the original stresses with mining activity. 3. The properties of rock that are significant in failure and its prevention.

Jan 1, 1960

By Brij M. Moudgil

Separation of dolomite from apatite, because of nonselective adsorption, cannot be achieved by conventional froth flotation technique. Results obtained in the present study also indicate, that this can be attributed to the depletion of the collector molecules due to complexation with the calcium and magnesium ions, dissolved from the two minerals. However, it has been established in this investigation that conditioning the material at pH 10, followed by reconditioning, without any additional collector, at pH 4, results in selective flotation of dolomite from the mixture. The recovery of apatite, in the proposed reconditioning process, is much higher than with the conventional conditioning under similar pH conditions. The mechanisms involved in the conventional conditioning, and the reconditioning process are presented.

Jan 1, 1983

By B. Yarar

Samples of coal from an adit in the Fording River District of British Columbia showed hydrophilic properties between depths of 0-24.5 meters and was naturally hydrphobic at higher depths. Laboratory experiments indicated that weathered samples (i.e., those mined at 0-24.5m) could be upgraded by froth flotation at pH<2 following slimes removal. The i.e.p. of samples varied regularly between pH=1.6-4.1, the weathered fractions being at the lower end of the pH scale. These values followed a pattern comparable with the flotation behavior of samples. A patchwise structure for coal surfaces determining the resultant disjoining pressure, which in turn determines flotation-non flotation relationships is postulated.

Jan 1, 1982

By William P. Shell

An important part of process control engineering is the implementation of the basic control system design through commissioning to routine operation. This is a period when basic concepts can be reviewed and improvements either implemented or recorded for application in future systems. The experience of commissioning the process control systems in the Homer City coal cleaning plant are described and discussed. The current level of operating control performance in individual sections and the overall system are also reported and discussed.

Jan 1, 1983

By Bruce C. Trent

In order to effectively model subsidence caused by underground openings, a two-dimensional computer code has been developed which couples near- and far-field response. The near-field is simulated by a discrete element block code and a finite difference code represents the continuum region in the far-field. The explicit equations allow rapid and inexpensive solutions to geometries which may lead to subsidence. Two sample problems are presented which illustrate the important features of the code.

Jan 1, 1979

By R. J. Jula

The process of treating granular activated carbon for return to service in the recovery of gold in Carbon in Pulp and Carbon in Leach circuits has been investigated. Carbons from four U.S.A. mines, one Canadian mine and one South African mine were characterized before and after regeneration. The use of thermal gravimetric analyses demonstrated the presence of inorganic compounds on the surface of the carbon. Thermal regeneration was investigated using factorial&apos; analysis to determine the effect or interaction of furnace temperature, retention time and the use of supplemental steam. The operation of acid leaching prior to or after gold elution was investigated. The effect of water quenching, regenerated carbon was also studied. From the data obtained in this investigation, guidelines are given for effective regeneration operation.

Jan 1, 1985

By L. A. Bellows

The "Athabasca oil sands" of the McMurray formation in northeastern Alberta cover an area of about 21,000 square miles and contain the world&apos;s largest reserve of oil. Fort McMurray, a small town in the heart of the oil sands area, is about 235 air miles north- east of Edmonton. A railway serves the town but no year-round roads connect the town with the rest of Alberta. (Figure 1). The McMurray formation is of early Cretaceous age, deposited unconformably on a limestone surface of Devonian age. The sediments appear to have originated from the Canadian Shield to the east and were deposited in bays and deltas of large fresh water lakes. The lakes were later replaced by marine seas in which t the overlying Clearwater shale was deposited. (Figure 2).

Jan 1, 1963

By Stephen C. Moore

The Grossschloppen vein-uranium deposit, Bavaria, West Germany, was examined utilizing underground workings during 1980-82 by Esso Erz GMbH, an affiliate of Exxon Minerals Company (EMC). Geologic evaluation entailed dense drilling of a portion of the deposit from workings constructed specifically for the program. Discovered in 1977, the deposit was initially explored by surface diamond drillholes which allowed definition of a 30-60 m wide vein system discontinuously mineralized along a 1000 m strike length and to at least a 450 m depth. The underground program was conceived as a cost effective procedure to answer questions on vein correlation, grade continuity and variability. A 1200 m decline allowed access for detailed sampling of approximately 10% of the known area of mineralization. Fanned drillholes, logged by gaga probe, were spaced to provide intersections of veins at 10 to 20 m intervals. Six cross cuts also penetrate the pitchblende and uranophane mineralization which occurs in 0.1 to 2.5 as thick quartz veins. Detailed cross-sections and level plans were constructed for resource estimates of the intensively studied portion of the vein system. The program resulted in the discovery of local, high grade areas and an average grade in the evaluated area nearly double that expected from surface drilling.

Jan 1, 1983

By Harold F. Yde

Hydraulic tailings fill in the Butte deep level mines was based upon studies made in 1958 by the Anaconda Company Mining Research Department, which published Bulletin No. 35, entitled "Hydraulic Stope Filling". Since then, many things have changed. At the time of the Research Departments study, dry mine tailings were hauled by rail cars from the Anaconda tailings ponds, twenty-five miles distant, to the underground mines&apos; tailings fill plants at the Leonard Anselmo, and Mt. Con Mines. Now, with the installation of the new Weed Concentrator in Butte, tailings is delivered by pipeline to a cyclone at the Kelley Shaft, and stope filling has become more highly automated and streamlined. Presently, mill tailings at approximately thirty percent solids by weight, is pumped from the concentrator, eight thousand feet horizontally and upward, to the Kelley Fill Plant, where they are dewatered and deslimed by three Krebs Model D20B Cyclones, which discharge the material into the cased and grouted mine delivery bore holes at desired densities up to seventy percent solids. The vertical boreholes and four-inch rubber lined Victaulic pipe carry the material downward to horizontal distribution lines, which in turn tap into the stops-filling, three inch, unlined steel Victaulic pipelines. The slurry may travel several thousand feet before it finally discharges into the stope, where it lends support to the mined-out area.

Jan 1, 1969

By David M. Parkes

The hydraulic movement of coal is here defined as the movement of all sizes of coal in pipes and open flumes, by gravity and against gravity. It is not restricted to coal which is in slurry form. In other words, it is not crushed to a size in the 8 to 20 mesh size range. The top size could be as high as 12 inches. The dewatering of coal which is transported hydraulically is carried out to restore the coal to a suitable form for further cleaning, or for transportation by other methods. The process involves complete separation of all the coal, wood and rock from the water so that the water can be recycled without undue damage to pumps, pipes and monitors.

Jan 1, 1976

By W. White

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies at the time of the Symposium.

Jan 1, 1986

By Dr. Ing. Hermann Boldt

The Bituminous Coal Mining Industry of the Federal Republic of Germany produces nearly 100 million t/yr of clean coal. The largest coal mining area is the Ruhr District with dimensions of 100 x 40 km (65 x 25 miles). Figure 1: Here is the general administration of Ruhrkohle Akteingesellschaft RAG with its three divisions. Other coal mining areas in Germany are the Saar District and the Aachen District. Ruhrkohle produces 70 million t/yr of clean coal. The company operates 28 mines in the Ruhr District with an average raw coal production of 18000 t/day. Their average mining depth is 831 m (2740 ft.) and the average seam thickness is 177 cm (70 in.). Figure 2: Preparation plant reject is 44.6%. All following production figures will be with reference to raw coal because the raw coal production is the technically relevant number. Mining operations are mainly in non-dipping coal deposits whereby mechanized equipment for flat seams is also applied to deposits dipping up to 45? Coal extraction is done exclusively by the longwall method. Approximately 200 longwall installations are in production at any time. The average longwall length is 221 m (730 ft) ranging between 140 and 290 m (460 ft and 960 ft). The average longwall advance of all operations is 2.8 m/day (8.4 ft per day). Average production

Jan 1, 1977