Search Documents

By Lianhui Jia, Yali Han

"The key technologies of a large rectangular pipe jacking machine with dimensions of 10.12m × 7.27m (width x height) include selection of rectangular cross-section cutting modes, analysis on the strength and stiffness of the rectangular shield, integrated control of electro-hydraulic proportional thrust systems and ground conditioning for excavation are presented in detail in this paper. These key technologies have been successfully applied and verified on site during tunneling, providing a new concept for the building of large rectangular traffic and pedestrian tunnels in urban areas for the future.1 INTRODUCTIONIn the past, underground tunnels were mainly used for drainage, sewage, utilities, metro tunnel, etc. and most of them had circular cross-sections. Recently, as a result of economic development, gradually accelerating urbanization process and diminishing ground space, underground tunnels have already become a new trend for urban underground space utilization. Due to the heavy traffic flow, the demands for rectangular cross-section underground tunnels, such as pedestrian underpass and road tunnel, are increasing gradually.The Rectangular pipe jacking machine (hereinafter referred to as RPJM) was firstly developed in Japan for the construction of metro station, pedestrian underpass, underwater tunnel by-passes, etc. Kazunaki Kawai et al. introduced a RPJM developed and manufactured by KOMATSU in 2002 [1]. Tosikazu Kubota et al. confirmed the rectangular tunnels’ superiority to circular tunnels with regard to larger inner cross-section and lower construction cost in their RPJM construction reports [2]. Compared to circular pipe jacking machines, a RPJM also has the merits of a higher inner tunnel space utilization ratio and is able to excavate in shallow overburden areas. As shown in Figure 1, the effective area of a rectangular tunnel is more than 20% higher than that of an equivalent circular tunnel."

Jan 1, 2016

This paper discusses the type of scaling operations presently in use in underground mines. It defines a scaling factor that is expressed as the area necessary to scale to extract 1 t (1.1 st) of ore. The problems associated with conventional scaling methods are discussed as well as recent developments in mechanized hand-held scaling de- vices and methods of loose detection. The elements of the scaling process are further analyzed. The conception and design of a mechanized scaling device, developed at Universite' Laval is also described. The results of field tests conducted in Quebec hard rock mines are presented. The experimental findings show that the mechanized hand-held scaling device shows potential in improving the productivity and safety of underground mining operations.

Jan 1, 1996

By S. K. Kawatra

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. In order to reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite, and that the bulk of the recovered pyrite is there either as a result of simple entrainment or by being physically locked with floatable coal particles.

Jan 1, 1991

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching' into a science. Leaching of copper, whether from copper-bearing ore or waste, follows well established chemical reactions. These reactions are commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300, 000 tons of copper are produced annually in this manner where as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced.. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydro-metallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks, or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 1, 1972

By A. K. Stagg

Toxic substances in On solutions can retard biological leaching of copper sulfide dump ores. On solutions were analyzed for metals, organics, and chloride, and showed inhibitory concentrations of aluminum, manganese, and chloride. Inhibition of bacterial activity by the solid fraction of On solution, with and without the organic constituents, was evaluated. Toxicity to bacterial species was evaluated by monitoring bacterial numbers, pH, Eh, and rates of iron oxidation. The On solution solids were toxic at 50 -60% of their field concentration. Most of the toxicity of the On solution was due to the organic fraction. Different SX reagents show varying degrees of inhibition of T. ferrooxidans. Bacterial inhibitory effects of carriers and lixiviants used in the SX plant should be determined so that entrained SX reagents do not retard biological dump leach systems. The reagents used should be the most cost effective and the least toxic.

Jan 1, 1994

By K. Feledi

"A booster fan is an underground mechanical ventilation equipment installed in series with a main surface fan that is used to boost the air pressure provided by the surface main fan passing through it. As mining continues to expand and go deeper, the need for improved and efficient ventilation increases. This has led to the use of booster fans and other auxiliary ventilation devices in underground mines. This paper details experiments and results carried out at Missouri S&T Experimental Mine that investigated air leakage and recirculation caused by the use of booster fans. The results were compared with the situations where booster fans are used and not used.The variables considered were the booster fan blade angle and the fan combinations. Air quantity measurements were taken at each individual stopping under a number of scenarios and across four blade angle settings. The first set of situations examined were; the main surface Joy fan only running, the main Joy, and the west booster fan running, and the main Joy fan and east booster fan running. Observations were made which lead to the conclusion from the experimental analysis that booster fans affect the behavior of leakage and recirculation. The locations of the booster fan and the blade angle setting have the most effect on leakage and recirculation. To limit the potential for system leakage and recirculation, the location and size of a booster fan in a ventilation system should be thoroughly evaluated.INTRODUCTION Missouri S&T Experimental Mine ventilation system The Missouri S&T Experimental Mine has two shafts. One currently serves as the main intake shaft. Air is forced through the main shaft by a Joy Manufacturing Vane Axial fan and follows the direction shown on the map on Figure 1. The air is currently naturally exhausted through the Wheeler portal. As indicated on the map there are eight stoppings in the mine, with stoppings number 2 and 8 fitted with man doors. The mine also consists of three raises which are either fully or partially blocked, two portals with one acting as an exhaust and the other generally closed by a hydraulic Kennedy door."

Jan 1, 2015

By Chee Theng

"Keep calm and carry on mining. That has long been the conventional wisdom in the mining industry, a largely cyclical one that has weathered roller-coaster booms and busts. But in the years from 2002 to 2016, an unprecedented steep rise in commodities prices that lasted a decade and then took a sharp turn downward had made it hard for gold and silver miners to stay the course.“The last 15 years highlighted some of the structural and inherent challenges that our industry has, from product price uncertainty to long lead times to the capital intensity of our business,” said Mitchell Krebs, president and chief executive officer of Coeur Mining, who was the luncheon speaker at the American Exploration & Mining Association’s 122nd Annual Meeting held Dec. 5-9, 2016, in Reno, NV.Looking back, Krebs said, “We were given this enormous gift of a commodities super cycle, and the industry kind of blew the opportunity.” While gold prices rose 319 percent and silver prices rose more than 200 percent over the 2002 to 2016 period, the XAU index of 30 gold and silver mining companies’ stock prices went up by only 20 percent.Entering 2016, precious-metals prices have made a comeback, with gold rallying strongly from a six-year low at the start of the year. This time, the industry is ready. Companies are leaner and meaner, with lower costs, reduced debt and an increased focus on higher grades and quality ounces. Although opportunities were missed in the past, the industry has got its act together and is now well positioned to take advantage of a price upswing and even to show profits when prices fall, as they did in August 2016, pushed down by a strong dollar."

Feb 1, 2017

By W. C. Morgan

This paper discusses some of the problems involved in predicting the productivity of a shovel and truck fleet in a new set of operating conditions. More specifically, it concentrates on the problems of predicting the travel times on the haul and return portions of the truck cycle under new profile conditions and the prediction of the interaction effect between the shovel and trucks at the loading point. The ability to calculate the travel times for a new road profile is not new. Additional corrections of these calculated times for expected actual operation can be made. In considering the interaction between the loader and the hauler, there are two approaches that can be taken. Probably the most accurate method of predicting the shovel-truck interaction is a simulation of the step-by-step operation considering the variation in cycle times of the shovel and trucks. This is usually called a stochastic simulation and requires input describing how these cycle times vary. However, by understanding the causes of this shovel-truck interaction it is possible to make sufficiently accurate predictions with much simpler methods. For the purpose of this discussion let us assume that the problem involves trying to predict the productivity of a single shovel-truck fleet at some future time in an existing operation. Let us also assume for simplification that the new operation to be simulated has the same loading and pit conditions and the same dumping conditions as did the existing operation. Therefore, the only difference would be the difference in the hauling profile for the new operation. The problem then becomes one of predicting the change in the travel times on the haul and return portions of the cycle, and in determining the change in interaction between the shovel and trucks with the new truck cycle times.

Jan 1, 1968

By H. E. Wyslouzil

The highly competitive nature of the international iron ore market has forced producers to improve the quality of their pellets. The demand for low acid pellets suitable for direct reduction has resulted in an increase in the number of plants utilizing reverse froth flotation for silica reduction. Column flotation is being favoured for this service due to the low capital and operating cost of the equipment, as well as improved metallurgical performance when compared to conventional flotation cells. This paper describes the benefits of column flotation and discusses some important aspects of circuit design.

Jan 1, 1993

By J. R. Dyni

Colorado nahcolite deposits, estimated at 29 billion metric tons, formed in an asp metric permanent-lake basin whose waters were rich in algae and sulfate-reducing bacteria. Nahcolite (NaHCOg) occurs in oil shale of the Green River Formation (Eocene) as aggregates (62 percent), disseminated crystals (24 percent), and impure beds (14 percent). Because much of the nahcolite is nonbedded, it will be mined with oil shale and can be concentrated to marketable grade by crushing and screening Impurities in nahcolite are kerogen, quartz, pyrite, and carbonate minerals. A promising new market for nahcolite is in the process of removal of sulfur dioxide from industrial stack gases. When heated, nahcolite reacts with sulfur dioxide to form sodium sulfate. Differences in thermally induced microporosity may explain why nahcolite is more reactive than trona, a possible competitor with nahcolite for SO2 removal. Limited production of nahcolite at one or possibly two localities is expected in the next several years, but large-scale production is probably at least 10 years away.

Jan 1, 1980

By Alan Bauer

In recent years there has been increasing interest in employing the technique of explosive casting in strip mines. Explosive casting, applied to dragline mining, describes the procedure whereby the overburden is horizontally displaced by blasting causing a portion of the material to be thrown into the previously mined cut. Therefore, it is not necessary to subsequently excavate this waste with the stripping equipment. In addition, allowing the overburden unrestricted movement during the blast most often results in improved fragmentation and enhanced machine productivity. The method is receiving attention because the capital and maintenance costs of stripping equipment has risen rapidly in relation to explosives costs. Improved productivity is necessary to maintain unit costs at an acceptable level.

Jan 1, 1983

By H. Fayed

Froth flotation technology is the backbone of the minerals pro-cessing industry where minerals are concentrated by selective separa-tion; either direct or in-direct flotation. In direct flotation useful minerals are conditioned to become hydrophobic (water-repellant) and attach to air bubbles while impurities (non-useful particles) remain in water. The hydrophobic particles are transported by air-bubbles to the top froth (foam) layer in flotation tank which can be removed as a concentrate. There are many factors that controls this selective separation process such as: particle’s degree of hydrophobicity, size, mass loading, air holdup and bubble size distribution. Turbulent fluctuation of the slurry in the tank is another important factor that controls the collisions rate between particles and bubbles and hence attachment rates. The turbu-lent fluctuations are measured by the local distribution of turbulent dissipation rates. Conventional flotation machines are restrained by residence time of the slurry that is about 3-5 minutes that results in a large footprint and limits the capacity of flotation plants. The designers of conventional flotation machines try to reduce the footprint of flota-tion tank by scaling up the flotation machines to increase plant throughput. The scale-up process reduces the specif power consump-tion and the local distribution of shear rates and turbulence dissipation rates. This scale-up results in a larger mean bubble size and lower particle-bubble attachment rates.

Feb 1, 2023

By Richard D. Begley

This paper will present the results of an analysis of several abandoned coal mine projects and includes field data for over a dozen different reclamation projects recently completed in the state of West . Virginia. The analysis was performed with the objective of summarizing and or classification of the environmental consequences with reference to the characteristics of the mining facilities (surface, underground, etc.). The analysis also addressed the itemized cost of remediation with respect to procedures, environmental concerns and time. The results of the analysis are that each abandoned coal mine site in West Virginia have/had many unique features and in most cases include a combination of environmental concerns that complicate comparisons. The study also revealed that the abandoned mine land program for mines abandoned prior to 1977 that is being financed by a tax on the production of coal, has produced many benefits for the state of West Virginia. This grant program administered by the Office of Surface Mining, has resulted in a high quality methodology of remediation that has been successful for many years in greatly minimizing and/or eliminating environmental concerns from abandoned coal mines.

Jan 1, 1997

By O. J. R. Baena

Mining activity in the Segovia region in NE Colombia is the main source of employment in the local economy. This has created major problems of illegality and informality mining associated with a high social and environmental impact, as inefficient technologies are used and high consumption of toxic substances required in the process of gold recovery by amalgamation and cyanidation. In this work is presented mineralogical characterization of six local mills and studied beneficiation processes developed in them. With the results presented a proposed plant design that eliminates the use of mercury by replacing gravity concentration processes taking advantage of the characteristics of the treated material. Significant results were obtained regarding the recovery of precious metals and present a methodology that can be replicated in other mineral beneficiation plants that use gold amalgamation processes. This implies a significant reduction in mercury use and decreased risk of human contamination associated with this.

Feb 23, 2014

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

 The paper combines theoretical and experimental analysis to improve the accuracy of predicting paste yield stress by slump flow. It derives an analytical model of slump flow for yield stress, providing a theoretical basis for quantifying the rheological properties of paste with slump flow. The study uses three different tailings-prepared pastes and constructs an empirical yield stress model, showing high accuracy and good generality.

Aug 1, 2023

By R. Miller

Lowering our globe’s emissions is a major effort as we move toward a future net-zero carbon environment requiring significant investment in a new, low-carbon infrastructure, along with key market incentives to change. Industry will play a key part in this transformation, requiring expertise in both energy and emissions. Key elements of the de-carbonization strategy are: energy data, emissions reporting method, governance, de-carbonization project generation and drivers, the MACC, electrification, and the de-carbonization checklist. For a zero carbon future, it will be key for business leaders to understand decarbonization, anticipate technological changes, and implement new business me

Mar 2, 2022

By Y. J. Wang

Editor's Note: Y.J. Wang's paper appeared in the September Technical Papers section. There were some inadvertent editorial errors in it. So we are reprinting it here. Abstract - This paper examines the ventilation network problem from a view point of solving a system of B equations in B unknowns, where B is the number o f branches in the network. Based on Kirchhoff s current and voltage laws, the solution to the general ventilation network problem must satisfy B network equations. In this paper, the air quantities and control-device pressures are chosen as variables and are grouped into B dependent variables (unknowns) and B independent variables, resulting in a system of B equations in B unknowns. Based on whether their variables are dependent or independent, the network branches are classified into f our types: five d, non-fixed, p-fixed, and q fixed. The ventilation network problem may include all four types of branches. There are .some conditions under which the problem as defined in this manner does not have a unique solution. To have a unique solution, the Jocabian matrix of the equations m us! he nonsingular. It then follows that: • the number of branches with independent air quantities must be less than or equal to the number of chords with respect to a spanning tree; •the subnetwork of branches with independent air quantities must not contain any cutset; and •the suhnetwork of branches with dependent control-device pressures must not contain any cutset. These three conditions must be met regardless of the values for the variables. In addition to the problem formulation, a solution procedure applying the Newton (or Newton-Raphson) method is outlined and illustrated with an example problem.

Jan 1, 1991

By Randy Fulton, Ignacy Puszkiewicz, George H. K. Schenck

Stuart Olson Construction, Inc. excavated 385m (1263 ft.) long twin tunnels with 6.25m (20.5 ft.) O.D., a portal and a cross-over for the Edmonton, "Metro". The work for Contract No. 76458, SLRT South Tunnel and Portal, in Edmonton, Alberta, Canada was performed in 1989 and 1990. NATM was specified because of the instability of glacial deposits. The contractor decided to use "two firsts" on this project: Fully mechanized NATM and a novel excavator¬mounted tunneling machine. An excavator was equipped with a cutter boom, and a loading and conveying system. This novel machine cost only about one-third of the price of a special NATM roadheader. This new combination of NATM and an excavator-mounted cutter boom offered a cost-effective alternative to shields, slurry TBMs and roadheaders for short tunnels in unstable ground. For NATM tunneling in hard rock or in mixed faces, the roadheader-type cutter boom can be replaced with an impact hammer (hydraulic breaker).

Jan 1, 1993

By R. F. Hüttl

The restoration of surface mining landscapes requires the (re)creation of ecosystems. In Lusatia (eastern Germany), large-scale open-cast lignite mining operations generated spoil dumps widely consisting of acidified, phytotoxic substrates. Amelioration and rehabilitation measures have been developed and applied to these substrates since the 1950s. However, it is still not clear whether these approaches are sustainable. This paper reports on collaborative research work into the ecological potential of forest ecosystem development on typical minesites in the Lusatian lignite district. At first sight, pine stands on minesites along a chronosequence comprising about 35 years did not show differences when compared with stands on non-mined sites of the general region. Furthermore, with some modification, conceptual models for flora and fauna succession in forest stands on non-mined sites seem to be applicable, at least for the early stages of forest ecosystem development. For example, soil organism abundance and activity at minesites had already reached levels typical of non-mined sites after about 20-30 years. In contrast, mine soils are very different from non-mined soils of the test region. Chemically, mine soil development is dominated by processes originating from pyrite oxidation. Geogenic, i.e. lignitic, soil organic carbon was shown to substitute for some functions of pedogenic soil organic matter. Rooting was hampered but not completely impeded in strongly acidified soil compartments. Roots and mycorrhizae are apparently able to make use of the characteristic heterogeneity of young mine soils. Considering these recent results and the knowledge accumulated during more than 30 years of research on minesite rehabilitation internationally, it can be stated that minesite restoration might be used as an ideal case study for forest ecosystem development starting at "point zero" on "terra nova".

Jan 1, 2002

By L. Bomvisinho

As a result of today?s requirements for larger mills with higher power demand, and in order to cope with maximizing throughput, and optimize grinding efficiency, the minerals industry is increasingly relying on the robust Gearless Mill Drive (GMD) solution. This paper describes the new features introduced with the revolutionary ABB drive controller for Gearless Mills, and explains the benefits this can bring to the operation. Extensive surveys have been performed with GMD users to gather suggestions and understand the market wishes. As a result the new driver controller capabilities and functionalities focus on safety, high availability, operational flexibility and remote diagnostics.

Jan 1, 2010