Search Documents

The role of ZnSO4 in activation of sphalerite (ZnS) and deactivation of lead-activated sphalerite has been investigated. Adsorption of metallic ions at the solid-solution interface, electrokinetic results for sphalerite under different chemical conditions, and thermodynamic calculations were used to elucidate the mechanisms involved. It is shown that flotation response of sphalerite in absence of activators is rather weak and that adsorption of ethyl xanthate on the mineral mainly electrostatic in nature. Zinc sulfate is found to activate the mineral but only in a narrow acidic pH range. This is attributed to the increase of zeta potential as well as the possible increase in amount of negatively charged bulk precipitated zinc xanthate. Lead ions activate sphalerite in a wide pH range and the lead activated mineral assumes a flotation behavior similar to that of galena (PbS). However, addition of ZnSO4 depresses the lead-activated sphalerite by replacing lead ions at the mineral/solution interface.

Jan 1, 1999

By Carl E. Schubert

The application of geophysical technology relative to the exploration, planning, and operation of coal mines is expanding. This is due to the trend of the industry to increase the size of operations, use of mechanized equipment and mining of more difficult coals, where unforeseen conditions can affect mine profitability. Coal is a good geophysical target because of its lower density, higher electrical resistivity, lower seismic wave velocity, and lower magnetic susceptibility in comparison to typical country rock. The more important techniques are well logging, high resolution seismic reflection, seam wave velocity, and radar. These methods can be used to map coal horizons, determine the physical properties of the coal, and identify mining hazards. The methods are not a pancrea however. Their use should be based on a careful assessment of their expected success and cost benefit analysis in comparison with conventional technology, primarily drilling, which none of the techniques presented should entirely replace. In general, the level of technology developed for geophysics surpasses their current level of application to coal problems. In some cases, identifying hazards in advance of mining using seam wave seismic in particular, the state of the art has been developed in Europe and is awaiting fruitful application in the United States.

Jan 1, 1982

By L. L. Anderson

Western bituminous coal can be processed to low sulfur liquid fuels by fast reactions. A process (LEFCO) under development at the University of Utah uses coal and catalyst under hydrogen pressure to convert 60 to 70 percent of the coal matter to fuel liquids and gases. Coals have been processed in small diameter (less than 1/2 inch) tubes and at reaction residence times of less than 10 seconds. Effects of process variables on the yield and quality of products have been studied. General features of the process and the properties and characteristics of the products produced are presented. Special features of the process that distinguish it from other liquefaction processes under development are also discussed.

Jan 1, 1975

By Pengfei Wang, Guorui Feng, Shufeng Zhang, Yuxia Guo, Tingye Qi, Dian Li

"Based on the geological conditions of the No. 10203 mining face of the Xinyang coal mine, a numerical model of the longwall backfilling face is built using the FLAC3D software to calculate the limit broken length of the key strata. Based on the deformation laws of the immediate roof, the backfilling parameters are determined. Furthermore, the movement laws of the overburden strata with different volume filling rates (0, 40, 60, 100, and 100%) and with different layout forms of the filling strip (under a volume filling rate of 60%) are analyzed. The results of the numerical modeling show that the stress of the two sides of the working face and the deformation of the overlying rock are gradually reduced with the increment of the volume filling ratio. In view of the deformation of the roof strata within the allowable range, a volume filling rate of 60% is selected to simulate and analyze the filling effect under different layout forms of the filling strip. The filling width, stress concentration area, and layout form of the filling strip are the key factors to control the movement of the overlying strata. In addition, the probability integral formula is used to calculate and predict the ground subsidence on the filling area, which confirmed that the backfilling mining method is fully applicable in the Xinyang coal mine. The results of this study provide a certain theoretical basis for the determination of the filling process in the field.INTRODUCTIONIn China and other coal producing countries, gob is managed using the caving, filling, supporting, and slowly sinking methods (Zhang, Zhou, and Zhang, 2009). With the continuing development of the concept of green coal mining (Guo, Deng, and Zou, 2004), the filling method, which is safe and environmentally friendly, has been widely used in the field. On one hand, this method could reduce waste rock and other waste discharge. On the other hand, it could effectively slow the surface subsidence. Recently, strip-filling mining mostly adapted the arrangement of the strip backfill with equal intervals and widths (Xie et al., 2004), but the reasonability of this arrangement should be discussed. To arrange the intervals and width of the strip-filling body reasonably, Feng et al. (2019) put forward the “constructional backfill mining (CBM)” concept. The CBM is a type of backfill mining with low backfill rate, strong structural stability, and good backfill effect. The targets of the CBM include the efficient usage of solid waste resources in mining areas to reduce the backfill cost, the improvement of backfill materials and backfill technologies to increase the backfill efficiency, and rational planning of backfill and mining scheme to reuse the underground mining space. The determination of proper width and intervals for the strip-filling body is the main content of the CBM. Strip-filling mining using cemented coal gangue backfilling is the main method to undertake overburden of the overlying strata and to slow down the surface deformation. It also plays an effective role in cost reduction (Xu et al., 2007). This study focuses on proper determination of the strip-filling body parameters according to actual geological conditions by a simulation. It provides an appropriate reference for backfill mining in the Xinyang coal mine."

Jan 1, 2019

By A. Wang

This paper defines the elements of a basic economic model for decision-making when considering a methane drainage system for an underground coal mine. A drainage system will require significant capital and operating expenses; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision-making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision-making are provided for an actual mine decision.

Jan 1, 1997

By J. Van Kleunen

In the Spring of 1959 the Riverside Cement Company, a Division of American Cement Corporation, placed into operation at their Oro Grande California plant a new crushing-blending-reclaiming facility. This new facility, in conjunction with other modernization in the plant, has established a degree of automation and reliability on a-plant-wide basis which heretofore had not been attained in the industry. The blending and reclaiming facilities for raw stone and cement clinker at this plant represent not only the first computer programmed materials handling system of its type in the industry, but also the first installation of specialized equipment which was designed for high capacity, fully automated operations.

Jan 1, 1963

By J. J. Schwoebel

Resource Enterprises, Inc. (REI) is exploiting the coalbed gas resource by working in unison with active underground mining operations. At REI?s pilot project at the Soldier Canyon Mine, Carbon County, Utah, REI has drilled nearly 15,250 m of horizontal in- seam and slant boreholes during the initial two years of drilling activity. Produced gas has been sold to a natural gas transmission company on a continuous basis since mid 1983.

Jan 1, 1986

By Lee W. Saperstein

P.L. 95-87 contains explicit demands for land-use planning in its reclamation and designation sections. Both sections require recognition of local land-use plans; however, the sections are not well integrated. Accommodations to these planning requirements may be found in suggestions based on British mineral planning practice. Better links can be created among local land-use planners, the state's permitting authority and designation office, and mine designers. Mining companies should take more interest in local land-use plans and in resource inventories; states should consider devolving to local government responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 1, 1982

By A. M. Gaudin

The recent study by R. M. Hays(l) prompted the study summarized in this paper. In his Interesting paper, Mr. Hays shows fine results to be attainable by a relatively complex flowsheet on a semi-taconite, a manifestly difficult ore to treat. We obtained a semi -taconite from Minnesota, and treated this sample by wet magnetic separation alone. The device in which the separation was accomplished is the standard pilot-plant, laboratory separator in use at Magnetic Engineering Associates' laboratory (MEA) in Cambridge, Massachusetts. It consists of a cylindrical space which can be magnetized by turning on the magnet of the separator. In this cylindrical space, there is a canister which provides the special configuration of the magnetic field and magnetic field gradients that MEA considers to be required. The ore pulp is made to flow through the canister while the current is on. A portion of the pulp is retained in the canister, and the rest is evolved as a non-magnetic fraction. The laboratory device is cyclic, but it accurately predicts the results obtainable by an Industrial unit of either cyclic or continuous type (moving matrix). The ore tested was 99.5°%o -325 mesh, and approximately 75% -500 mesh. The concentrate from this ore was, therefore, eminently suitable for pelletizing. In passing the ore through the magnet, we had the choice of repeatedly passing the concentrate from the first step through the operation, or of repeatedly passing the non-magnetics. In our experiments, the first method was clearly superior from the stand¬point of the cleanliness of concentrate. Of the many tests which we have made, we think that we have to retain two which

Jan 1, 1971

By F. W. Bond

Predictive ground-water modeling is currently being applied to a wide range of engineering applications. In recent years models have been used to evaluate the effect of large ground-water withdrawals on regional water supplies; subsidence associated with overpumping; siting and design studies for chemical dumps; siting and safety aspects of nuclear waste storage; and heavy metal migration from disposal sites. Similar modeling techniques could be used to analyze water-related problems in the minerals industry such as mine dewatering (both open pit and underground), environmental and pollution control, and process water supply and disposal The objective of this discussion is to describe how ground-water models are being used to assist in the solution of water-related problems outside the industry and to extrapolate that use to mining problems.

Jan 1, 1980

By X. Cheng

A series of batch flotation tests was performed on chalcopyrite-quartzite, pyrrhotite-quartzite, and on chalcopyrite-pyrrhotite-quartzite mixtures. Pulp potential measurements in the flotation tests of single sulfide minerals indicated that each sulfide mineral had its own optimum potential range for flotation. When these results were used to select the potential ranges for the separation of the two minerals from their mixture, their flotation responses changed and the selectivity of separation was adversely affected. A possible mechanism involving surface alteration through galvanic interaction is discussed. A method to improve the selectivity of flotation separation was proposed.

Jan 1, 1992

By J. P. De Carvalho, R. Dimitrakopoulos

An actor-critic reinforcement learning approach is presented to improve the production of an industrial mining complex by defining shovel allocation and adapting the short-term plan given grade-control decisions. Blasthole data updates the simulated orebody models, which are input into a stochastic grade-control method based on a spatially constrained clustering approach that minimizes the profit-loss function. These aspects are embedded in a discrete-event simulator that defines the material flow from faces to processors. A case study at a copper mining complex shows the methods’ ability to adapt to new information, improving the quality of the material feed and increasing cash flow by 23% compared to a baseline case.

Jun 25, 2023

By J. M. Ekenes, C. A. Caro

"New approaches that increase hydrometallurgical recovery from refractory minerals in below mill cutoff -grade sulfide copper ore can add significant value, improve profitability and increase ore reserves. This paper describes the development and implementation of an engineered heap (EH) approach to leaching low-grade, chalcopyritebearing ore at Freeport-McMoRan’s mine in Morenci, AZ. The technical evolution of the engineered heap concept is described together with the challenges and benefits following implementation. Introduction The Morenci ore deposit, located in eastern Arizona, has been mined for copper for 140 years. Mineralization in the Morenci district consists of sulfides and oxides. To process these ores, Morenci operates concentrator and leaching circuits. Leaching accounts for two-thirds of the copper produced in Morenci. More than one-half of this leaching-derived copper production comes from run-of-mine (ROM) stockpiles. The largest category of material moved in Morenci is destined for ROM stockpiles and waste dumps. Materials that are not economic to mill or leach are designated “waste.” However, this designation can change based on improvements in extraction technology and commodity prices. Chalcopyrite does not leach well due to its refractory nature. For predominant chalcopyrite mineralized ore, copper recovery during a typical leaching cycle may be as low as 5%. For this reason, chalcopyritedominant ores below mill cutoff grade have historically been classified as waste. By incorporating advanced leaching technology to improve metal recovery from previously leach-resistant ore types such as chalcopyrite, the Morenci Mine has been able to reclassify substantial amounts of this “waste” to “ore.” Process chemistry Chalcopyrite copper extraction is temperature, oxygen and ferric dependent. The temperature is achieved primarily by pyrite oxidation (Eq. (1)) and secondarily by oxidation of chalcopyrite itself (Eq. (2)). The regeneration of ferric in solution can be enhanced by providing the appropriate acid and oxygen levels according to Eq. (3). In the absence of microorganisms, this reaction is very slow."

Jan 1, 2015

By M. A. Klugman

[This paper represents a portion of a lager study, concerning dispersion patterns of major, minor and trace elements in wall-rock about ore-bodies in part of the Colorado Mineral Belt. This phase of the work pertains to the Mg/Ca ratio variations in wall-rock adjacent to ore-bodies in two mines of the Alma-Horseshoe Mining District of Central Colorado. The mining district is located 80 miles southwest of Denver (Figure 1) on the east flank of the Mosquito Range. The area is typified by rugged relief with altitudes from 10,500 to 14,000 feet.]

Jan 1, 1962

By K. F. Unrug

Fractures of sedimentary rocks in the vicinity of the outcrop are commonly encountered around the world. Mine highwalls and numerous highway cuts give excellent views for detailed study of surface fractures. This paper gives an explanation of the origin of fractures as well as characterization of the distribution and extent of joint system with reference to lithologic composition of the rocks. Practical implications of the joint system affecting mine operations are described. Among the subjects discussed are: discontinuous deformation as an effect of surface subsidence, stability of mine portals and near outcrop underground operations, and stability of highwalls, when using highwall miners and strip operations. Some design procedures are recommended that can minimize the problems encountered in mining areas with intense joint systems.

Jan 1, 1994

By Francis S. Kendorski

INTRODUCTION Caving offers the lowest cost per ton of any large-scale mining method, but its successful application demands an ore body that conforms to several rigid requirements. The deposit must be of wide areal extent, massive and not spotty in ore values, and insensitive to ore dilution. It must also be a rock mass that breaks up readily. There are only three active caving operations in the US-Climax, Henderson, and San Manuel-but caving methods have recently taken on new importance as deeper lower grade mineral occurrences and ore bodies are found. These deposits are too deep for surface min¬ing methods, and too low grade to support any type of underground mining except a bulk method such as caving. Announced discoveries or indications that may be amenable to caving include: Climax's Mt. Emmons molybdenum discovery in Colorado; Molycorp's Goat Hill molybdenum prospect in New Mexico; the Phelps Dodge molybdenum deposit in Beaver County, UT; Arizona copper occurrences such as Asarco's Sacaton, Hanna's Casa Grande, Noranda's Lakeshore, and Ken¬necott's Safford; Anaconda's suspected deep copper de¬posit in Butte, MT; Anaconda's Carr Fork, UT, deposit; and perhaps others. CAVABILITY'S ROLE IN FEASIBILITY STUDIES Caving is a system of underground mining which removes support from underneath an ore body. As a result, the rock mass fractures, fails, and flows vertically downward by gravity to be collected in previously ex¬cavated funnels. Types of ore that have been mined by caving include molybdenum, copper, iron, nickel, as¬bestos, and diamonds (Julin and Tobie, 1973). It is primarily a large-scale method, with production rates of more than 45 300 t/d (50,000 stpd) having been achieved. However, the initial capital investment before return is very high, often in the hundreds of millions of dollars. The cavability of an ore body or mineral occurrence is a critical item in the feasibility study of a proposed mine, not only from the point of overall minability, but from the point of impact on other costs such as blasting, loading, hauling, crushing, and grade recovered. Aside from the often-asked question of, "Will it or will it not cave?" the real questions are, "Can we afford to make it cave, carry the rock away, and extract the mineral?" The last is not a topic of this chapter, but the first two are. The cavability of an ore deposit or mineral occur¬rence is based on many things, but clearly, if a large enough area is undermined, any rock mass will cave. The result could be a violent collapse as occurred at Urad, CO (Kendrick, 1970), or perhaps the rock mass will cave beyond the ore boundary. Another unfavor¬able result could be ore blocks that are too large for the equipment and orepasses to handle without considerable secondary blasting. Weak rock with numerous fractures may produce a very fine ore when it caves, resulting in dilution and ground control problems. DETERMINING STRUCTURAL DOMAINS It has long been recognized that the geologic nature of an ore body is important to cavability (King, 1946). Such items as weak rock material, intensity of fractur¬ing, and severity of faulting all contribute to the success of a caving operation, and information regarding these is required as a minimum for the cavability determination. In practice, the rock mass-defined as the blocks of intact rock together with the intervening fractures, joints, faults, bedding planes, and other discontinuities-that contains the ore body, as well as the surrounding and overlying rock, must be examined in a systematic and detailed fashion. Surficial geology maps must be pre¬pared, exploration holes drilled, and core logged for en¬gineering information. The fracturing of the rock mass must be studied to ascertain the three-dimensional dis¬tribution of fractures and their characteristics, and faults must be located and described. The strength and other mechanical properties of the rock material, the fracture surfaces, and the fault filling materials must be tested and reported for later use by designers and planners. With this basic information and an understanding of the geologic setting, the rock mass can be divided into one or more structural domains which tend to behave similarly in response to engineering activities (Robertson and Piteau, 1970). One must keep in mind that the determination of the structural domains goes beyond the geologic units present. Several lithologic units may be lumped together, while a single lithologic unit can be divided into multiple domains. Major faults often form their own domain, and the direction of engineering ac¬tivity-for example, cave advance to the north rather than the south-may alter rock mass behavior, resulting in different domains. As an example of the detailed rock fracture map¬ping required for such studies, the structural domain determinations at the Climax mine (Kendorski, 1973) are shown in Fig. 1. The circles are Schmidt equal area projections of the three-dimensional attitudes of frac¬tures (Ramsay, 1967) mapped in detail at various rock exposures. The attitude of fractures is important to the cavability determination since it dictates the directional behavior of the rock mass as it fails, and determines the effectiveness of arching, keying, and rock block inter¬locking. Low-angle fractures must be present to allow movement of the rock in the vertical direction during undermining (Mahtab and Dixon, 1976); if low-angle planes of weakness are absent, the rock mass may arch with a keystone effect, rather than moving vertically downward.

Jan 1, 1982

By E. M. Williams

The U.S. Bureau of Mines recently conducted a limited-scope study on the use of lineament analysis and electromagnetic geophysics to better identify the surface expressions of faults at the Cimmaron Mine near Raton, NM, an operating longwall mine in the York Canyon mine complex. Two normal faults were encountered by the mine, one during gate road development and drilling and another only through drilling. The potential ground control problems and offsets associated with these faults will severely impact long-range development plans, so it is essential to know the lateral extent of these faults within the coal reserves. The surface topography at the site is fairly rugged, yet outcrop exposure is poor. There is no obvious visible geologic evidence to indicate that the faults identified at depth extend to the surface. Both the geophysical and remote sensing techniques provided information on the presence and extent of important geologic structures which could not be gained just from drilling and surface outcrops. The geophysical surveys also were invaluable in confirming the presence of subsurface geologic structures in the vicinity of the lineaments assumed to be associated with the faulting.

Jan 1, 1995

By P. C. Schutte, A. J. Kielblock

INTRODUCTION Certain activities, such as emergency work and rescue operations, often have to be undertaken in environments where heat loads often exceed limits prescribed for routine work. This is particularly relevant to the South African mining industry where heat stress-induced fatalities are not uncommon during rescue operations. In this regard an excessively hot environment is defined as one where either the dry-bulb temperature exceeds 37,0°C or the wet-bulb temperature exceeds 32,5"C, and it is therefore not surprising that heat stroke mortality escalates rapidly when these limits are exceeded. A review of both local and international standards indicated that the available information on safe exposure times under abnormal heat stress conditions is very limited. Where available, such standards are aimed at the general population, including both sexes, irrespective of age and also the least heat tolerant worker, and not at a medically-screened, all-male population free of grossly heat intolerant individuals, as is the case in the South African mining industry. It is suggested that available norms and limits are too conservative for local application and, therefore, unrealistic. In view of the definite need to protect workers when exposed to abnormally high environmental temperatures, the present study was undertaken to establish a scientifically derived data base. applicable to local conditions, to determine safe exposure times: Any exposure limit, especially in an emergency situation, should be easy to administer, valid and reliable. These aspects, there- fore, form an integral part of this paper. FORMULATION OF HEAT STRESS LIMITS The formulation of heat stress limits was based on the criterion that a heat exposed individual should experience a negligible risk of developing dangerously elevated body temperatures. In order to provide a database for risk assessment, certain physiological responses of heat tolerant men were determined at various combinations of thermal conditions and work rate in a climatic chamber. These physiological responses were analysed statistically in order to predict safe survival and tolerance times as a function of thermal conditions and work rate. EXPERIMENTAL DESIGN A total of 202 randomly selected, medically fit mine workers volunteered for the study on the basis of informed consent. These men were considered to be inherently heat tolerant in as far as they had successfully completed a heat tolerance test (Anon., 1991) or the standard climatic room acclimatisation procedure used on many South African gold mines (Anon., 1989). The subjects were allocated randomly to 14 experimental groups and each group was exposed in a climatic room to one of

Jan 1, 1997

By T. Hollingsworth

The Boddington Gold Mine, located near Perth in Western Australia, has recently completed the construction of a new process plant. An overland conveyor system was installed to convey the ore from the primary crusher to the process plant. This paper will discuss the overland conveyor?s mechanical design including dynamic analysis and the selection of primary mechanical and electrical components.

Jan 1, 2010

By Charles G. Zink

Early anthracite "deep mining" methods, production, manpower. underground transportation, labor, safety and reserves are reviewed and compared to the present and to future requirements which must be met in order to economically win the fourteen million tons of untapped reserves and to keep the product competitive in the market place.

Jan 1, 1971