Search Documents

By Wedam Nyaaba, Edward Wellman, Angelina Anani, Eduardo Cordova, Sefiu O, Cluber Rojas, Adewuyi

This study aims to investigate the optimal method for ore pass construction in incompetent rock masses. We evaluated the conventional and raise boring methods based on safety, efficiency, excavation control and ground support for ore pass construction. A stability analysis using analytical Q-raise (QR method) and kinematic analysis methods for ore pass construction with a raise borer before and after grout injection of the rock mass was performed. As a case study, an ore pass (diameter of 3 m, depth of 100 m) within an incompetent rock mass was considered to gain further insight. The rock mass was characterized according to the classification methods Q Barton, rock quality designation (RQD), rock mass rating (RMR) and geological strength index (GSI). The grout intensity number (GIN) method of grout injection was used. The safety factor of less than 1.075 obtained before injection was lower than the acceptance criteria. However, grout injection before raise borer excavation resulted in a safety factor greater than 1.5. Using a raise borer without pre-grouting indicated that the maximum unsupported diameter (MUSD) of the ore pass was less than the required 3 m and equal to or larger than 3 m post-grouting.

Dec 1, 2024

By Robert M. Mann

The Ag/S specific ion electrode has been evaluated for analysis of both free and total cyanide. Metal cyanide solutions were prepared from reagent grade compounds and by stoichiometric fixture of the metal with a potassium cyanide solution. Solutions containing Cu+1, Ni+2, Fe+2, Fe+3 and Zn+2 complexes were analyzed prior to and following EDTA pre treatment. This effort provides an understanding of the effect of each metal cyanide complex on the SIE analysis of free and "total" cyanide.

Jan 1, 1981

By Daniel Saramak, Agnieszka Saramak

A big issue in crushing and grinding operations in raw materials handling is high energy consumption and low breakage effectiveness. According to the Legendre [7], only 10% of energy input is directly consumed on the feed material breakage, while the remaining portion is dissipated in the form of heat and noise [8]. In the industry of limestone powder production, the grinding operations constitute integral part of technological circuits, and the energy consumption in operations of industrial comminution consume as high as 2% of world energy [14]. High-pressure grinding is the technology with proved energy benefits both in ore processing circuits and in limestone grinding. The promising results concerned mostly the achieved energy savings and good results of material breakage were achieved and demonstrated in numerous investigations [1,3,12]. However, it appears that a proper selection of operational parameters of the press devise, determination the feed material characteristics and adjustment of process course san be of a key-significance in improving an effectiveness the HPGR operation. Operational parameters of devices and process course should be verified towards the characteristics of the feed material, which mainly applies to the particle size and shape of the feed material and its moisture, and also mineralization in case of ores [2,4,9]. There are various investigations concerning an impact of the operational pressing force on comminution results which mostly refer to the determination of energy consumption and crushing ratio [5,6,10,13]. Investigations on the moisture content are less common, however their results suggest that, in general, the HPGR feed with higher moisture shows the tendency to higher comminution intensity, while the energy consumption increases together with increasing of feed material moisture. Investigations on olivine sand feed [11] showed that crushing ratio decreases for higher moisture, especially when the material is crushed at higher pressing force. HPGR devices, however, shouldn’t be regarded as a unique and perfect solution for comminution of each type of material. But they indeed may bring technological and economic benefits, comparing to conventional crushing and grinding machines, resulting in more favourable breakage of material particles and lower consumption of energy per unit mass of processed feed material.

Feb 1, 2025

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016

By T. Mudder

The objectives for closure of a hard rock mine include minimizing long term environmental liability, attaining regulatory compliance, and maintaining geotechnical stability, while closing as cost-effectively as possible. Proper planning for closure should come during the feasibility study, design and permitting phases, and during operations as updates. The lack of a proper or updated closure plan can result in severe environmental and economic consequences. Effective mine closure is the result of a combination of innovative concepts, long-term commitments, and multi-party cooperation. The purpose of this paper is to discuss concepts, commitments, and cooperation as they relate to an effective closure plan.

Jan 1, 1999

By G. S. Grainger, R. A. Cummings, F. S. Kendorski, R. L. Butts

Georgia Power Company's Rocky Mountain Project, located approximately ten miles northwest of Rome, Georgia, in the Valley and Ridge Physiographic Province, is a pumped-storage facility rated at approximately 800 megawatts of peaking energy. Geological field explorations and borings enabled the division of the rocks along the tunnel and shaft alignment into distinct lithologic units and defined the ground--water regime. Field explorations included a detailed analysis of the rock mass discontinuities at available rock unit exposures. Testing of rock strengths was performed in several phases in both the field and the laboratory. The field testing consisted of point-load testing, geophysical testing, in situ load testing, and hydro-fracture testing. Laboratory testing determined the Brazilian split-tensile strength, the unconfined compressive strength, the triaxial compressive strength, the joint-direct shear strength, and the pulse velocity. The rock mass along the tunnel and shaft was also characterized by empirical classification systems. The classification systems included the Rock Mass Rating (B1IR) and the Rock Mass Strength Determination (RHSD). The results of the field explorations, field testing, laboratory testing, and rock classifications were used to divide the rocks into two structural groups. These rock groups were defined as volumes of rock wherein the rock mass behaves similarly in response to the excavation. Each group, therefore, required separate rock engineering consideration.

Jan 1, 1986

By John S. Harper

Can the mining industry in the United States accept the change and challenge of the "Now Generation" of entirely new high-performance automated transportation systems? Good Question! While there has been some revolutionary new thinking and product testing in mining, none has taken place in transportation of ore and waste. With one notable exception - DASHAVEYOR - not a single really new and 'unconventional' system has even been tried on a small scale in the hardrock mines in our country. Admittedly, U.S. equipment manufacturers share the responsibility for the slow progress in mine transportation systems in our country, since they have provided very litte leadership in design innovation or education. First, let me give you my definition of what is meant by the term "Advanced Transportation Systems". Then I will describe and compare such systems, emphasizing the strong and weak features of each as they apply to vertical and horizontal haulage. I will conclude by establishing the principal requirements for implementation of these types of systems in the mining industry in the United States.

Jan 1, 1969

By Mortimer J. Richardson

In the context of this session on "Practical Placer Mining," a projection of the present into the future first assumes that there is a future for Placers. The second assumption is that there is the combination of adequate reserves and a willing, mining investment source to finance placers. This paper will point out the opportunities on both assumptions, illustrating my positive position on the future of gold placers. In order to focus this paper more effectively, I have chosen GOLD as the subject mineral. However, it is recognized that much of the technology for exploring and mining gold placers has been applied to other alluvial deposits; including platinum, diamond, tin, and various industrial minerals (which are often referred to as "placers" though this contradicts historical definitions). Over the past 10 years I have presented several papers on the general subject of placers, most of which are listed under References. These have included topics such as exploration, evaluation, small-scale gold placer mining and decision-making, mining and processing equipment designs, and dredge-mining operations. In an attempt to identify the more promising, undeveloped placer potentials in the world I have usually mentioned the USSR and China but qualified them as being either inaccessible, or, politically difficult to obtain. However, with recent developments in the USSR, the obstacles appear to be somewhat diminished.

Jan 1, 1992

By P. L. Yorio, D. R. Willmer

"The current paper presents the results of a study designed to explore the types of practices that are fundamentally important to developing and maintaining comprehensive risk-based health and safety management systems (HSMS) in mining organizations. Eighteen practicing health and safety (H&S) executives, managers, and professionals from a variety of mining commodities were asked to assess the fundamental importance of 20 distinct elements and 133 different practices assembled from a review of several HSMS consensus standards. The research approach assumes that developing and maintaining a robust HSMS requires unwavering attention to activities designed to either: 1) directly contribute to a risk management system’s plan-do-check-act cycle; or 2) build an organization’s internal infrastructure without which the cycle cannot be sustained. The results of this study suggest that the following areas require consistent focus and attention: Leadership Development; Accountability; Knowledge, Skills, and Abilities Development; System Coordination; Culture Enhancement; Behavior Optimization; and Risk Management Studies. Each element and its corresponding top-ranked and top-rated practices are discussed.INTRODUCTION Since the time of the Industrial Revolution, occupational health and safety (H&S) management has been a topic of practitioner thought and academic inquiry (1). In the U.S., decades of regulation and research have resulted in a surplus of prescriptive information (techniques, tools, approaches, standards, programs, practices, policies, etc.). With an abundance of such information, a simple H&S solution to address a problem in the U.S. mining industry may seem straightforward. Counter to this assertion, however, some evidence suggests that the abundance of information may create complexity and cause confusion in the minds of organizational leaders and H&S managers, ultimately discouraging the voluntary pursuit of a sound approach (2). In line with this perspective, in 2006 the U.S. National Mining Association (NMA) formed an independent commission to examine H&S management issues within the mining industry. The findings of the commission called for the mining industry to adopt a risk-based management paradigm. In the presentation of its findings, the commission stated that “…every mine should employ a sound risk-analysis process, should conduct a risk analysis, and should develop a management plan to address significant hazards identified by the analysis” (3). Grounded in the well-known plan-do-check-act cycle, the recommended risk management system allows for mines to ground strategic management choices in their mine-specific hazards and risk profiles"

Jan 1, 2015

By Cloyd D. McDowell

The Federal coal Mine Health and Safety Act of 1969 has been criticized by those who say it goes too far in controlling the activity of private enterprise and by those who say it does not go far enough in eliminating fatalities and accidents in an accident prone industry. Possibly a better evaluation of this legislation lies somewhere in between. From the viewpoint of the coal industry it can be said that through the efforts of those engaged in mining, both the operator and the miner, the year 1969 marked a record year in mine safety with only 190 fatalities and a frequency of 0.84 per million man hours exposure. This outstanding achievement compared to any previous was the result of a determined effort on the part of a concerned industry to improve its reputation as being the most hazardous industry in the nation. After the effective date of the Act, March 31, 1970, the Bureau of Mines assumed complete control of all safety and health activities of the mining industry. Unfortunately, there was no improvement in the safety record of underground mines in 1970 with the total of 255 fatal injuries and a frequency of 1.04 for the year. The number of fatalities declined to 177 in 1971 but the number of underground coal mines had declined from 5,955 to 2,268 during the two year period. Meanwhile, surface mined coal increased from about 38% of total production in 1969 to over 50% in 1971, keeping the annual production of coal at a normal level but involving fewer men.

Jan 1, 1973

By B. I. Pålsson, H-Å. Häggblad, J. F. Stener, P. Jonsén

"Understanding mill charge motion is important. In the charge, the center of gravity is shifted from the rotational center of the mill system, and its motion is induced by rotation of the mill. At the same time, the charge creates a torque in the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to this motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty of measuring inside a tumbling mill. Experimental measurements in a lab mill were done for a number of load cases: varying feed material, mill filling, mill speed and pulp liquid. The mill is set up to measure the charge-induced torque. The accuracy is good, with relative uncertainty less than ± 2% for relevant load cases. A full three-dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill startup behavior for torque and mill power. This proves that the model is physically correct, and can be used for modeling large-scale mills.IntroductionUnderstanding of the charge motion within the mill is of importance in mill optimization. The breakage of ore particles and the wear of liners/ball media are closely linked to the charge motion. To study these phenomena in a physically correct manner, appropriate numerical models for different parts of the mill system must be used. Validation of these models is of major importance. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behavior of the mill charge.For structural analysis, the finite element method (FEM) is the most developed and most frequently used numerical method. FEM is a numerical solution method based on continuum mechanics modeling. A constitutive relation for the actual material is described, and the governing equations are solved in Zienkiewicz and Taylor (2000). Varieties of different constitutive models for a large number of materials are implemented in modern FEM code. The computability of nonlinear problems in solid mechanics is investigated in Belytschko and Mish (2001), among others."

Jan 1, 2015

By Basar Arioglu, Mustafa Tanriverdi, Seok Jae Seo

"INTRODUCTION Istanbul is a unique megalopolis connecting two continents. Population growth and economic development require permanent solutions and continuous investments on the transportation infrastructure. While the average population growth rate in Turkey is around 1.3% per annum, Istanbul is growing at an even faster rate of more than 1.5%. Even more striking is the fact that car ownership in Istanbul is increasing 5% a year, which is four times faster than the population growth. Although Istanbul Metropolitan Municipality (IMM) has worked persistently to improve the quantity and quality of the public transportation system in the city through, in particular, extending the available rail system network, the need for extra roads has always fallen behind demand. To make things worse, Istanbul is divided by the Bosphorus Strait, the large waterway connecting the Black Sea to the north and Marmara Sea to the south, which leads to the Mediterranean. This waterway is crossed via two suspension bridges, the Bosphorus Bridge built in 1973 and the Fatih Sultan Mehmet Bridge built in 1988. Current daily traffic across the bridges is around 450,000 vehicles per day. Ever increasing cross-Bosphorus traffic demands require other routes to be in place a soon as possible. While a third bridge farther north is currently under construction, yet another tunnel crossing is coming to the end of construction and is planned to be in service by December 2016. Being implemented under a Build-Operate-Transfer (BOT) model, Istanbul Strait Road Tunnel Project (ISRTP, the Project) has been under the spotlight not only because of its distinctive technical characteristics but also because of its robust business model, exacting financial and legal arrangements, diverse stakeholders and challenging organizational management structure. The following paragraphs offer an overall view of the Project from inception to where it stands now and extend to the imminent operational phase, touching lightly on all major aspects of this challenging journey."

Jan 1, 2016

By D. J. Benton, S. Finley, D. T. Orr, A. J. Chambers, M. A. Stepan

"Corrosion of ground support can lead to falls of ground that pose a significant risk to miner safety. To address this problem, the National Institute for Occupational Safety and Health (NIOSH) is investigating corrosion at the Hecla Mining Company’s Greens Creek Mine, located near Juneau, Alaska, USA. Field studies have used photogrammetry surveys to document welded-wire mesh corrosion, and laboratory studies at NIOSH’s Spokane Mining Research Division (SMRD) have investigated the effects of corrosion on ground support integrity. Findings show that (1) corrosion monitoring through photogrammetric methods may be effective for qualitative measurements of welded-wire mesh corrosion, and (2) there is a relationship between loss of load-bearing capacity and the diameter loss due to corrosion in welded-wire mesh. Photogrammetry results thus far have measured an apparent bulking of the corroded welded-wire mesh, and preliminary laboratory tests have investigated the relationship between the larger bulked and effective wire diameter. If this relationship is verified, these results may indicate that photogrammetry, when combined with the models produced in laboratory tests, could offer a means of monitoring corrosion levels, as well as rock rib deformation. INTRODUCTION Reducing the number of rock fall injuries and fatalities is an important part of the mission of the National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD). Ground control using support systems to protect miners from rock falls is one of the oldest mining sciences, and considerable research has led to a variety of modern tools and methods in use today. Among these tools are rock bolts and welded-wire mesh, which are made from increasingly higher-strength steel grades to meet the increasingly demanding requirements of underground mines [1]. However, the benefits of these higher-quality support elements may be negated in corrosive mining environments. A better understanding of how corrosion affects the support capacity of ground support systems will assist engineers in determining when an opening is at a greater risk of falls of ground. Accelerated corrosion has been occurring in some areas of the Hecla Mining Company’s Greens Creek Mine near Juneau, Alaska, USA. Corrosion of ground support has resulted in two falls of ground occurring between April 2015 and March 2016. While these falls of ground did not injure any personnel, mine management recognized the high risk to miner safety and responded by actively undertaking a ground support rehabilitation program. Rehabilitation measures include the installation of both galvanized and coated, corrosion-resistant bolts and welded-wire mesh, depending on local conditions."

Jan 1, 2017

By M. P. A. Hames, D. R. Beaumont

INTRODUCTION Legend has it that when Isembard Kingdom Brunel was confronted with the cost and consequences of one of his bridges having failed, he responded cheerfully that the event had saved investors and taxpayers a fortune because it prevented him from repeating the same design at several other locations. To meet the demands of rejuvenating and expanding the transportation system in an era of industrial growth Brunel and his contemporaries introduced bold designs and many innovations. Great advances in design and construction techniques resulted, yet these too had their practical limits as the story tells. In the gold mining industry today we face the same challenge of expansion, yet designers must respond mindful of economic restraints. Is innovation the answer? It has two meanings; to bring in novelties and to make changes. Distinguishing between improvement and novelties, or simply recognizing the benefits and limitations of new ideas over proven technology is part of good design. This paper will illustrate the practical aspects of selecting appropriate solutions to a design problem by examining a variety of examples common throughout the industry. Since a variety of engineering disciplines contribute to the design of a gold processing plant, and each has some old wisdom to impart or new development to boast this paper is divided into the different areas of expertise involved.

Jan 1, 1987

By B. A. Hancock

New permit discharge standards instituted at Hecla Limited?s Lucky Friday Mine required installation of water treatment plants to manage water quality at two outfalls to the South Fork of the Coeur d?Alene River. The 002 Outfall Water Treatment Plant (WTP) is a clarification-filtration plant for treating the combined mill and underground discharge water flows. Process optimization efforts were a significant challenge until the negative impact the exploration diamond drilling products had on the clarification process was identified and resolved. The products were being wasted directly to the mine water discharge system which was pumped to the surface WTP. Anionic soluble oil and polyacrylamide based products were causing TSS particle hydrophobicity and dispersion that greatly affected coagulation and flocculation response, resulting in excessive chemical usage and treatment control issues. This paper details how problems associated with the drill products negatively impacted the 002 WTP and how system changes, alternative product usage and treatment at the source resulted in more consistent plant performance.

Jan 1, 2011

By C. R. Zegarra

Extraction of manganese, gold, and silver from a low-grade manganiferous-silver ore was investigated by thiourea leaching followed by standard cyanidation. The levels of reagent concentrations in this investigation were 0.0 -1.0 M thiourea and 0.0 -1.0 M sulfuric acid. Temperature and agitation speed were maintained at Z5 °c and 300 rpm, respectively. The dissolution of gold, and silver was shown to be dependent mainly on sulfuric acid and thiourea concentrations. In general, 50.0 % Ag, 98.0 % Au, and 75 % Mn were recovered from a Mn-Ag ore by thiourea leaching. Overall silver extraction of 98.0 % was obtained by cyanidation after thiourea leaching. Thiourea leaching of sodium bisulfite leach residues was also studied, and the total extraction of gold and silver were 97 % and 40 %, respectively. Finally, a two-stage thiourea leach was also investigated.

Jan 1, 1988

By B. J. Scheiner, D. A. Stanly, P. M. Brown

The Bureau of Mines has developed an equation that describes the dewatering of clay slurries with poly- ethylene oxide. This dewatering equation is: A[ ] = KC + b where n, k, and h are empirical constants and C is the concentration of polymer solution used for dewatering. The minimum amount of polymer required for dewatering, A, is determined by titration of the clay slurry with a polymer solution. In this report, the dewatering equation is applied to data obtained for a polyacrylamide dewatering sequence. Fundamental similarities between the dewatering properties of clays and the viscosity of polymer solutions were observed. These similarities were explained by correlating an equation describing polymer configuration in solution with the dewatering equation. This correlation showed that the amount of polymer required for dewatering and polymer solution viscosity are both the consequences of the frictional interaction of entangled polymer coils.

Jan 1, 1991

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

The Kaldo furnace is a type of top-blown, rotary reactor that is widely used for the production of precious metals. During the production of doré, a gas jet of compressed air is injected through a water-cooled lance to impinge upon the molten bath surface in the presence of molten metal and a slag phase. A common problem during operation is the difficulty in controlling the distance that the injection lance can penetrate through the reactor mouth without being splashed by the molten phases. Splashing may produce accretions on the lance surface as well as plugging of the nozzle at the lance tip. An additional problem may occur when the gas jet impinges upon the furnace wall and causes rapid wearing of the refractory linings. Because the conditions prevailing in the Kaldo furnace offers poor visibility to the human eye, its operation mostly relies on the empirical knowledge of plant operators and process engineers. A systematic study in a scale model of the Kaldo furnace under controlled laboratory conditions may be valuable to estimate the maximum penetration distance of the injection lance, and thus help improve the operation of an industrial reactor. From a fundamental perspective, the observation of the basic features of the flow patterns in the scale model may help elucidate the relevant phenomena governing the hydrodynamics in this type of system.

By George Hufford

An investigation is made into the applicability of queueing theory to simulating the operation of a large open pit copper mine in the southwestern United States. Actual data from a working mine was used to construct curves for truck loading time, haulage and return time, and dumping times. Known results of investigations of queueing models (Koenigsberg - 1958, Gordon and Newell - 1967, Cabera and Maher - 1973) were used to simulate the actual operation. These did not give acceptable results so commonly used probability distributions were fitted to the actual data. A large computer program known as Q-GERT was used with the various parameters obtained from fitting the curves. Kolmogorov- Smirnov tests were run that showed that this was not satisfactory either. Finally, Q-GERT was used with the actual data from the mine. An appropriate correction factor is then found to apply to the exponential probability distributions tested previously and satisfactory results are obtained.

Jan 1, 1981

By Peter Kolitsch, Galyn Rippentrop

INTRODUCTION On April 14, 1994, the joint venture of Kiewit Construction Company and Kenny Construction Company was awarded a 76 million dollar contract for the construction of the New Hampshire Avenue Tunnels in Washington D.C. The Notice to Proceed was given on May16, 1994 and scheduled completion is September 1997. This project is one of five contracts for the Mid-City E Line as part of the Washington Metropolitan Area Transit Authority (WMATA)Greenbelt Route. Once completed, the Mid-City E Line subway tunnels will connect service between the U Street-Cardozo and Fort Totten stations (See Figure 1). The New Hampshire Avenue Tunnels project consists of approximately 6800 feet of twin single track subway tunnels, three vertical shafts, associated utility work and comprehensive restoration work. Section E4b involved two methods of tunneling along the project alignment. The first method consisted of the well known soft ground open face shield driven tunnel and the second method consisted of tunnels driven using the New Austrian Tunneling Method (NATM) . The NATM section of twin tunnels begins at the Buchanan Vent Shaft and proceeds approximately 2630 feet under Rock Creek Cemetery, including the Farragut Emergency Access Shaft and connects approximately 390 feet beyond to the existing Fort Totten running tunnels (See Figure 2). Special considerations had to be given to the portion of the tunnel alignment which passed beneath Rock Creek Cemetery. The analyses and subsequent selection of the tunnel support system were based on anticipated geological conditions and the sensitive tunnel alignment. The New Hampshire Avenue Tunnels project was the second soft ground NATM project in Washington D.C. The first, by no coincidence, was completed at the adjacent Fort Totten Station and Running Tunnels Project by Mergentime/Hochtief, AJV. Currently, on a nearby WMATA jobsite, the J.F. Shea Construction Company has started a third NATM soft ground tunnel. Tunnel support systems were studied with respect to three tunneling methods: •A one-pass system consisting of a bolted precast concrete segmental lining •A two-pass system consisting of an unbolted precast concrete segmen

Jan 1, 1997