Search Documents

By S. Renslow, G. Wang, L. R. Moore, Y. Xiong, J. Gu

"Clays are known to contribute to a wide range of mineral processing challenges. These challenges can haunt a plant from the pit, through the beneficiation plant and even to the tailings pond and process water. Each step that the clay is present potentially experiences significant and costly impacts to the process efficiencies. The effect of clay minerals on the performance of phosphate flotation was investigated. The investigation led to an understanding of the movement of clay through the beneficiation plant, the impact on reagent usage, and the overall flotation performance. INTRODUCTION With the decline in mineral feed grades, mineral processing will continue to face challenges. One significant challenge would be obtaining high recoveries of industry specified quality mineral concentrates with lower quality raw minerals. Other challenges may be the handling of the excess tails and process water being produced to maintain a mill’s production volumes. For example, increased levels of clay have been, and will continue to be, a topic of concern for many mines. Some of these concerns include environmental regulations associated with water storage and discharge, as well as beneficiation. Gonglun Chen reported that clays produced in the phosphate industry are generally colloidal and fine (90% < 45 µm) (Chen, 2006). As such, these clays can take 20-30 years to settle, in the absence of polymeric assistance. The settling of these clays is essential as an accidental discharge can lead to substantial impacts to the wildlife and ecosystem. The Environmental Protection Agency (EPA) has referenced cases where the discharge of water can result in fines in the tens of millions of dollars, and at times causing the processing plants shut down, depending on the volume and quality of this discharged water (EPA, 1997). The turbidity discharge criteria will vary from state to state. Florida’s Department of Environmental Protection has listed a turbidity maximum of 29 NTUs, or 60 mg/L total suspended solids, above the natural background condition (Florida Department of Environmental Protection, 2016). A lot of the literature has been focused on the impact of high levels of clay (>10%) on mineral processing. Farrokhpay has reported the significant impact of clay minerals on froth stability in copper flotation (Farrokhpay, 2012). He reported that clays can form a hydrophobic slime coating on the surface of bubbles, which can yield an increase in froth stability. Clay concentrations as low as 5% can have significant impacts on the rheological properties or slurry viscosities. Increased slurry viscosities can lead to either elevated pumping/processing energies being required, decrease in flotation efficiencies due to a decrease in bubble mobility through the pulp, or decreased throughput to manage these viscosities (Tu, 2005; Farrokhpay, 2013; Burdukova, 2014)."

Jan 1, 2017

By R. Pandey, G. Elie, E. Sarver

Respirable crystalline silica (RCS) is generally considered the most hazardous constituent of coal mine dust, and a new federal rule is expected to further limit exposures in U.S. mines. For regulatory purposes, RCS is monitored by collecting filter samples, which are analyzed for quartz (the predominant form of RCS in coal mines). The analysis is done using Fourier transform infrared spectroscopy (FTIR) in a centralized laboratory. To enable more timely results, National Institute for Occupational Safety and Health (NIOSH) mining researchers developed a directon- filter (DOF) FTIR analysis method and free FAST software that can be used in the field. For samples collected under specific conditions, FAST processes the FTIR spectral data to determine quartz mass. While the DOF FTIR method is not approved for regulatory RCS monitoring, it could be useful for engineering purposes, such as to evaluate mining parameters or new dust controls. This field study demonstrates how the method, including FAST, can be applied using low-cost, widely available sampling components. It further demonstrates how quartz percentage can be estimated in the field, by pairing a continuous personal dust monitor with a filter sampler.

Jun 1, 2025

By Arnold E. Lamm

The degree of economic, progress of a nation is measured by its possession and use of energy, sources. The future of coal in the West hinges on its ability to participate and grow in the energy market. A source of energy is, in the long run, only as good as the ability of the industry to develop its reserves economically. The economic development of the tremendous coal reserves, literally hundreds of billions of tons of coal in the States of Colorado, Utah, Wyoming, Montana, New Mexico, and Arizona, poses a very real question in the light of the known mining technology of our day. Basically in America today, coal is mined from the earth either by the strip mine or underground mine method; in the West, the large long-term, contracts now in force with utilities are mostly from coal mines utilizing the strip mine method. However, the preponderance of the known coal reserves of the West are located deep underground and will have to be mined by the various; underground mining processes. The problems encountered in the West with regard to underground mining vary from state to state but, on the whole, do not present what might be considered a miner&apos;s bonanza. I do not mean to&apos; infer that the underground coal of the West is unmineable, but I do want to emphasize that the tremendous reserve figures do not present a true picture in the light of present day technology.

Jan 1, 1965

By Richard A. Thomas, Liming Yuan, James H. Rowland III, DAVOOD BAHRAMI

To reduce the number of injuries resulting from fires on mobile, diesel-powered mine equipment, it is crucial to promptly suppress a fire once it is detected. The focus of this research was to determine the effectiveness of fire suppression agents. Large-scale tests were conducted using five different fire suppression systems based on: dry chemical, wet chemical, dual agent (dry and wet chemical), carbon dioxide, and water mist. Suppression nozzles were placed around the diesel engine where diesel fuel, engine motor oil, and hydraulic circulating oil spray fires were ignited. The results of this study can help mining companies and manufacturers by providing scientifically based data on the capabilities of the different fire suppression systems.

Feb 1, 2024

By I. J. Jansen

Successful soil construction involves preparation of an adequate base, selection of high quality soil materials, and placement of those materials by means which will establish a continuous macropore network and modest to low soil strength. Where such has been accomplished, experiments reveal row crop productivity on reclaimed land which is very competitive with that on undisturbed land. Inferior productivity and sensitivity to drought stress are experienced where the soils are excessively compacted during construction. Some deep tillage practices have been quite successful in improving the compacted soils, but it is preferable to avoid compaction as the soil materials are handled.

Jan 1, 1987

By Zohreh Kazemi Motlagh, Evan J. Owen, Virginia T. McLemore, Jakob Newcomer

Five-element style deposits are unusual hydrothermal systems that are typically characterized by a nickel-cobalt-arsenic- silver-bismuth metal assemblage. This mineralization is often represented by abundant native silver, arsenic, or bismuth, and followed by nickel, cobalt, and iron arsenides (skutterudite, safflorite, nickeline, rammelsbergite, and lollingite). The Black Hawk district in Grant County, New Mexico is one of the few examples of this mineralization style in the United States. Despite the differences in formation temperature, depth of emplacement, and host rocks between five-element style deposits worldwide, there are commonalities in mineralogy, ore texture, and composition. A detailed exploration of the native metal and arsenide phases will be performed to compare ore forming fluids between systems and the effects on styles of mineralization and paragenesis, as well as to aid in broader classification of the deposit style. Mineralogy and mineral relationships of the Black Hawk District and other five-element deposits worldwide will be characterized by reflected light petrography, scanning electron microscopy, X-ray diffraction, and electron microprobe analysis. Mineralogical phase diagrams will be generated to better understand the driving processes and evolution of the systems through native metal and arsenide precipitation.

Feb 1, 2024

By S. E. Phillipson, S. Romberger

The Late Miocene San Cristobal Ag-Zn-Pb deposit represents syngenetic and epigenetic mineralization with low- and high-sulfidation characteristics. The geology of the deposit is characterized by barren dacitic ring fracture domes, mineralized resurgent rhyodacite domes, strongly altered and mineralized tuffaceous lacustrine sedimentary rocks and an extensive crystal-lithic tuff debris apron. The orebody is hosted by intracauldron sedimentary rocks and breccias. Fluid inclusion data suggest that silver, lead and zinc were transported as chloride complexes and precipitated by cooling in veins from <5% (by weight) NaCl eq. fluids at 170° to 215°C. Silver spatially and perhaps temporally associated with resurgent rhyodacite was transported as a chloride complex and precipitated by increased H2S activity or increased fluid pH.

Jan 1, 2002

By Alessandro Navarra, Aldo Quelopana

For decades, open-pit mine planning algorithms have incorporated geological uncertainty and other elements or characteristics for increasingly realistic representations. Among these complexities is the detailing of downstream processes that occur inside processing plants. Previous studies have demonstrated that the strategic mine plan and mineral concentrator design are coupled, and should therefore be optimized simultaneously within the same quantitative framework. However, existing frameworks offer limited representation of operational modes. This work demonstrates an approach to resolving this gap, in an optimization based on a parallelized Variable Neighborhood Descent (VND). The resulting algorithm embeds mass-balancing linear programming (LP) using a DantzigWolfe decomposition. A case study of a Zn-Pb deposit is presented to show the performance reached.

Jun 25, 2023

By George White

On June 25, 1876 Lt. Colonel George Armstrong Custer led the Seventh U.S. Cavalry Regiment., comprising 31 officers and 637 enlisted men, into the valley of the Little Big Horn River in southern Montana. His assigned mission was a reconnaissance-in- force to locate the Indians reported to be assemblying in that area. Custer was extremely successful in locating the Indians. Unfortunately he located more than 3000 Cheyenne and Sioux under the leadership of the great war chiefs Crazy Horse and Gall. Custer&apos;s entire battalion of more than 200 men was annihilated; there were no survivors. While I don&apos;t seriously suggest that things will be all that bad in the uranium industry, I do suggest that some very fundamental changes have occurred in the uranium market. Conventional thinking based on past truths will no longer suffice. Geology, economics, politics, nuclear growth pat terns, technology, and utility attitudes have all changed. New thinking is in order. It is at this point that I would offer my usual disclaimer. My views regarding the future are simply that--my personal views. My belief that certain events will come to pass does not mean I view those events as appropriate, wise, good, equitable, or economic.

Jan 1, 1985

By W. G. Kegel

The past few years have produced a rash of demands for changes in America&apos;s way of doing things. From manufacturer to consumer, the rules have been changed. Some of the demands were needed and, when legislated to requirements, did manage some good for all concerned. Other demands made by zealots and taken up by regulatory agencies have forced costly changes on our way of life. No segment of industry has been exposed to more new rules and regulations than the deep coal mining industry in the United States. There is no denying that some good has evolved, but most mining men know that the effects have done more to reduce production and increase cost than they were ever intended to do.

Jan 1, 1975

By R. L. Grayson

Evidence has accumulated indicating that cultural change toward safer workplace behaviors is beginning to occur systematically in the coal industry. Through a range of programmatic mining company successes, enforcement and litigative actions, economic responses to competition, and integrated efforts by federal and state agencies, a broader participation of safety and training professionals is being achieved to address prioritized workplace problems at mines. Small steps in workplace-related improvements have been realized already, but the trends in industry safety statistics, coupled with focused programmatic initiatives, indicate that more definitive and systematic steps are occurring to improve safe behavior in the workplace routinely.

Jan 1, 1996

By K. D. Luxbacher, J. T. Davis

"A wind tunnel was designed to examine air flow, heat transfer and layering near an active fire at a working face. This tunnel simulates an active entry in an underground coal mine including an attached cross-cut of similar dimensions. A steel rectangular duct 1 ft. (0.305 m) tall, 3 ft. (0.914 m) wide and 10 ft. (3.05 m) long composes the main body of the tunnel and represents a mine entry. Air flow is generated by an exhausting centrifugal fan attached to one end of the crosscut. This fan was sized to supply air velocities based on Froude scaling. A 6 in. (15.25 cm) propane burner is used to simulate fires of various heat release rates at the working face. Thermocouples are used to map heat layering in the tunnel. Ports are installed for the introduction of tracer gases into and from sampling the system. Barometric, differential pressure, and temperature sensors are also included to monitor environmental conditions. Details about the design and testing of the system are presented including an overview of how the tunnel was scaled to accurately represent fire and flow phenomena. Finally, the proposed use of the tunnel for better understanding of mine fire phenomena and prevention is given. INTRODUCTION Fires in underground mines have been a concern since the dawn of mining. While technological advancements, regulations and best practices have improved both fire detection and firefighting techniques, mine fires continue to represent high risk events. From 2006 through 2015, fires accounted for 1.06% of fatalities in underground coal mines and 0.85 percent of fatalities in all underground mines in the United States (U.S. Department of Labor, 2006 to 2015). In addition to the risk of loss of life, mine fires can cause millions of dollars in equipment damages and lost production revenue. Extensive research has been conducted on how fires occur and spread in underground mines. In addition to testing conducted by government agencies such as the Mine Safety and Health Administration (MSHA) and the National Institute for Safety and Health (NIOSH) (e.g.(Liming, 2006), researchers like Verakis and Dalzell (Verakis, 1988) and Lowndes, et. al. (Lowndes, 2004) have furthered this field by studying ignitions and propagation of conveyor belt fires. While the studies of belt fires in mines are extensive, studies focused on fires at the working face are few in number. The particularly confined space and limited access to a working face, coupled with less robust, temporary ventilation controls create a unique environment that warrants special attention. Separate from studies on mine fires, the use of tracer gases to characterize flow patterns in normal mining ventilation is well established. In 1982, Timko and Thimons (Timko, 1982) outlined current and future applications of sulfur hexafluoride (SF6). However, little experimentation has been conducted to study specifically how tracer gases might be used to evaluate active mine fires and the fires’ effect on the surrounding mine environment (e.g.(Lindsay, 2014). In order to better understand the dynamics of smoke layering from a fire in an enclosed space, a small-scale apparatus was designed to map smoke layering and to examine other aspects of fire behavior at a working face. In addition to studying smoke flow around an active fire, experiments will be conducted using tracer gases in order to determine how they might be used to evaluate an underground fire."

Jan 1, 2017

By John T. Langstaff

Rock bursts in the deep metal mines of the Coeur d’Alene district present an ever increasing problem in the safe and economic mining of the district’s silver, lead and zinc ores. Hecla Mining Company operates two mines in the district - the Star, a 1100-ton/day lead-zinc mine, and the Lucky Friday, a 750-ton/day silver- lead mine. Rock burst problems at both operations prompted Hecla management to make an all-out attempt to find a practical method of predicting and eventually controlling these bursts. Research by personnel from the Denver Research Center of the Bureau of Mines at ASARCO&apos;s Galena Mine indicated that a recognizable pattern of seismic activity preceded some bursts and this activity could be precisely monitored by present- day, off-the-shelf electronic devices. Using information gained by the Bureau and other sources, Hecla designed and installed a 24,- channel seismic monitoring system in the Lucky Friday mine. Installation was completed in December 1973 and after a year of successful operation, it was decided that a similar system would be installed in the Star mine. This second installation was completed in June 1975. Both systems are now operating and providing continuous information on underground seismic activity. Each monitoring system consists of a network of geophones with attendant amplifiers that are connected by shielded cable through an interfacing device to a computer. The origin of each seismic event is determined by the computer and a three-dimensional location is printed out. This information is plotted daily and is used to pinpoint rock burst prone areas and chart their relative seismic activity. This paper will review the causes and effects of rock bursts in the Coeur d&apos;Alene district, the equipment and operation of the microseismic system at the Star and Lucky Friday mines, and the results obtained to date.

Jan 1, 1977

By J de Cuyper, V. M. Lovell, W. Freyberger

The recovery of apatite from the phoscorite ores occurring in the Transvaal, Republic of South Africa, involves a flotation process that is particularly difficult to characterize from a fundamental point of view. However, the reagents used, (tall oil fatty acid, nonylphenyltetraglycol ether, sodium silicate, and sodium hydroxide) can successfully bring about a separation of apatite from dolomitic calcite, which is the most troublesome gangue component. Recently, it has been demonstrated with some flotation feeds that the addition of certain polysaccharides can improve the flotation significantly. It has been shown that the metallurgy obtained is closely linked to the nature of the froth, and this, in turn, is influenced, often dramatically, by the presence or absence of certain of the reagents. The character of the froth depends less on the inherent frothing ability of these reagents than on the presence or absence of fine mineral particles in the froth, and on their surface characteristics and state of aggregation. The polyglycol ether and the polysacchar- ides have been shown to affect these properties, and it is suggested that a major function of these reagents is to modulate the properties of the fine particles in the pulp, thereby changing the character of the froth and giving rise to improved results.

Jan 1, 1976

By John A. Herbst, William T. Pate

Column flotation is emerging as one of the most important new separation technologies of the decade. Attendant to this development is the need for a quantitative understanding of the dynamic characteristics of columns. An understanding of the many important sub-processes occurring in the cell makes possible the development of dynamic simulators for flotation columns which will aid in the design of control systems for dynamic and steady state optimization. This paper presents a dynamic model for the column flotation cell developed from a population balance point of view similar to that which has been successfully applied to conventional flotation cells. In particular, the mixing that occurs within the pulp is modeled with a distributed-volume, mixer-in-series model as an approximation to the axially dispersed plug flow transport that occurs in the cell. This simpler approach avoids the distributed transport model which often leads to mathematical intractability. Other phenomena dealt with are the attachment and detachment of particles from bubbles in the froth and pulp, the transport of water and the bubble volumes with the froth and pulp phases. Simulation of the flotation of an Illinois No. 6 coal in a pilot plant flotation column were performed to test control strategies.

Jan 1, 1989

By J. E. Gray

Before specifications are discussed it may be well to define the term "Mineral Aggregates." Professor K. B. Woods (1) defined "Mineral Aggregate--An aggregation of sand, gravel, crushed stone, slag, or other material of mineral composition used in combination with a binding medium to form bituminous and portland cement concrete, macadam, mastic, mortar, plaster, etc., or alone as in railroad ballast, filter beds, and various manufacturing processes, such as fluxing, etc. " This definition is too all inclusive for the purposes of this paper; therefore, this discussion will be confined to specifications for natural aggregates which means sand and gravel and crushed stone, and limited primarily to coarse aggregate which is aggregate larger than one-quarter inch in size. To the uninitiated, this may seem to be a very limited subject on an unimportant material. However, aggregates are essential in all types of construction. The tonnage and value of these two aggregates produced in the United States during 1959 as reported by the Bureau of Mines were as follows: Sand and Gravel 729,895,000 tons valued at $728,527,000 Crushed stone 581,721,000 tons valued at $824,411,000

Jan 1, 1961

By H. R. Green

The design of slurry launders has usually been based on strictly empirical concepts. An examination of the most common procedures reveals that they do not account for many of the variables that are recognized as Significant for slurry transport. These may include flow rate, volume concentration of solids, solids specific gravity, solids size distribution particle shape, launder geometry, and roughness of the wetted surface. It was decided to develop a design procedure, which would accomplish two things: First: Take into consideration most of the known significant variables and systematize the procedure to assure consistent results. Second: Provide a rational basis for examining and utilizing operating data to refine and improve the system. To accomplish this, it was necessary to develop a basic design concept. This concept has been developed through a complex development history, and yet still appears workable and technically sound. That concept may be outlined as follows: First: The solids transport velocity is the fundamental basis for slurry launder design. Second: The stream configuration, hence the launder size, is integrated with the solids transport velocity so that the actual stream velocity exceeds the solids transport velocity. Third: The launder slope is that which will achieve the required actual stream velocity. It was originally planned to utilize a series of charts and nomographs for the design procedure. A nomograph, based on data given in Taggart&apos;s Handbook of Mineral Dressing (1), was developed to determine the solids transport velocity. The velocity thus determined was used with Manning charts to determine the launder slope .and configuration as though the fluid were water. It was planned to utilize a "slope adjustment factor" to increase the slope to compensate for the apparent viscosity of the slurry. All attempts to develop a suitable correction factor failed. This failure was principally due to the complex relationship of viscosity to the required slope. It was then decided to revise the entire approach. Specifically, the present procedure is based on the Darcy-Weisbach flow equation, which is rationally preferable to the Manning equation. The Camp (2) equation is used for the solids transport velocity. The necessity of reference to the Moody curves for the Darcy friction factor is avoided by using the Colebrook and White (3) equation. The resulting mathematics require iterative solutions for several of the unknowns.

Jan 1, 1978

By D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees&apos; levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Jan 1, 1997

By G. Bonifazi

In the present work the possibility to utilize the morphometrical and morphological characteristics of an articulate solids system in a slurry flow to monitorate and to control a continuous process is considered. This goal has been reached by mean of an optical system able to acquire, to handle and to process the pictorial information derived by a suitable hardware architecture designed to realize the best lighting, focusing and sampling conditions for the examined flow stream domain. The procedure has been tested using different flow stream slurries coming from different sections of a beneficiation plant. A suitable strategy and a consequent software architecture has been set up in order to assure to the system the necessary speed and the stability to achieve correct on-line measurements and control.

Jan 1, 1994

By X. Nie

A new one-step process was developed to completely eliminate iron and directly obtain pure Ni, Co, and Cu chloride catholyte from nickel rich matte by low temperature (400 0c) chlorination roasting of Ni, Co, and Cu with HCl and leaching with water (PH 7). The effects of roasting temperature, time, oxygen potential and HCI addition and leaching temperature, pH, H2S04 addition and residue sulphur on the recovery of metals and purity of leaching solution were investigated. More than 99 % of Ni and Co and 95 % of Cu in the matte was directly extracted into the solution while 99.995 % of Fe remained in the residue. The iron concentration in the leaching solution was less than 3.6 X 10-5 mol/L.

Jan 1, 1994