Search Documents

By P. N. H. Bhakta, X. P. V. Lei

The U.S. Bureau of Mines developed an alkaline oxidative pretreatment to increase the recovery of gold from refractory sulfide ores containing arsenopyrite (FeAsS) and/or pyrite (FeS2). Pretreatment of a low grade ore containing 0.4% FeAsS, 3.5% FeS2, and 2.74g/mt Au with 1.2m NaOH, 40 psig o2, 100° C, and 4 hr in a 2-L autoclave resulted in 94 to 96% sulfide oxidation. cyanidation of the pretreated residue resulted in 88% Au extraction compared to <20% Au extraction for untreated ore. Cyanide consumption was 0.25 kg NaCN per metric ton of ore. A flowsheet for treating sulfidic low-grade gold ore is proposed.

Jan 1, 1990

By Marco Aurelio Piangatelli, Massimiliano Bringiotti, Ferdinando De Angelis

"The construction of the three connecting tunnels between the east side and the west side of station C13, adjacent to the Vistula river, has a long and complex history, as they cross beneath one of Warsaw’s main road arteries (Wislostrada). After the attempt to excavate the first tunnel, the face of the tunnel collapsed on the night of August 13, 2012, and a volume of about 10,000 cubic meters of liquid mass (water, silty soil and sand) entered and flooded the west side of the station, which was filled with more than seven meters of material. Fortunately, the workers managed to escape, but machines and equipment were lost. This is the story of how the tunnels were completed, by adopting soil improvement, jet grouting, GRP bars, ground freezing and a careful choice of work steps. INTRODUCTION The Centrum Nauki Kopernik station on Line II of the Warsaw Underground is located alongside to the Vistula river (Figure 1). This station hereinafter is referred to as station C13.The station consist of three parts: the east and west part, and three connecting tunnels 40 meters in length with a large cross section (170 m2).. It includes the rails along the sides and the platform along the centre. The reason for the underground connection of two shafts with a tunnel is due to the presence of a road tunnel (Wislostrada, hereinafter called WS), which must be underpassed by the new metro line (Figure 2).The existing tunnel (Wislostrada) was built many years before, between diaphragm walls, and some foundation structures interfere with the underground tunnel. The challenge was to build the connectors without stopping the traffic of vehicles along the highway above. All works took place in very difficult geological and groundwater conditions due to the presence of Vistula alluvial deposits with poor mechanical characteristics. The soil profile consists of relatively loose sands on top, and silts overlying high plasticity Pliocene clays highly disturbed by the effects of the repeated over-sliding of glacial moraine deposits."

Jan 1, 2016

By P .. F. Ziemkiewicz, T. E. Rymer, J. J. Renton

Prediction and quantification of acid mine drainage (AMD) from a given rock unit is in its infancy. Acid Base Accounting is the current procedure. II is a useful screening procedure and is designed to indicate whether a rock unit will or will not produce acid. In this sense, Acid Base Accounting is qualiwtivc. Researchers at West Virginia University arc developing a prediction method to estimate how much acid will be produced over the life of a rock unit's AMD production. TI1c AMD prediction procedure can also evaluate the required rates and effectiveness of various AMD control amendments. This presentation discusses the WVU AMD prediction procedure in the context of historical approaches and indicates the mechanics and applications of this new technology.

Jan 1, 1991

By Robert C. Meaders

In this paper, autogenous grinding is defined as the combined crushing and grinder of a run-of-mine ore or the product from a primary crusher, in a single stage grinding mill. This is in contrast to pebble milling where pebbles are substituted for steel balls to grind a ball mill size feed. The autogenous mill to compete in efficiency with normal methods of crushing and grinding must not use greater power, must use less labor and steel, and must produce an equivalent product.

Jan 1, 1963

By Stephen D. Schwochow

Aggregate producers nationwide well recognize the numerous problems often faced in securing local approval to open and operate new gravel pits and rock quarries. Similar problems are faced in Colorado, but this region also presents certain political, social, and geological complexities that have become particularly troublesome in the last 10 years. The gravity of the local permitting dilemma can be related directly to the worsening supply-demand imbalance for aggregates in the state&apos;s most populated area, the Front Range urban corridor, particularly the Denver metropolitan area. The drive to develop crushed-rock reserves to supplement dwindling alluvial supplies and to meet increasing regional growth demands was somewhat predictable but perhaps more a "last resort" alternative forced onto producers by a hesitant and often apathetic government.

Jan 1, 1982

By P. K. Naik, S. C. Das

Leaching studies of low-grade manganese ore containing 31.77% Mn and 23.71 % Fe from Nishikhal, India, were carried out using pyritiferous lignite as a reductant in sulfuric acid medium. The variables studied were quantity of lignite, sulfuric acid concentration and temperature. Regression equations for the extraction of manganese and potassium were determined from 23 full factorial design data. The experimental conditions for the extraction of manganese were optimized using the steepest-ascent method. It was found that 99.03% of the manganese could be extracted in three hours with an ore to lignite ratio of 1:1.8, a sulfuric acid concentration of 1.9 M and a temperature of 99°C. Key words: Leaching, Manganese ore, Lignite, Statistical design

Jan 1, 2003

By George H. K. Schenck

It seems appropriate to review the history of mechanization of our underground coal mines at this time when many favorable flags are flying for this industry. It is a reasonable hope that such a review may stimulate thinking as to the directions that new technological developments are apt to take and in which members of the Society of Mining Engineers are destined to play important roles. Discussion of the relative importance of the various changes that have taken place since the advent of electric power provides the starting point. It is in the economic factors utilized that we find conditions which permit more efficient utilization of the capital committed to the industry. Concepts rather than specific items are emphasized in the following discussion because once the value of a concept, such as mechanical conveyors, is established, it then spawns many variations which are not significantly different. The shift from animate to inanimate energy has been the most important change in the modern industrial scene, including coal mining. Although introduced into coal mines for some purposes early in the period of general electrification, the coal industry adopted mechanical power relatively slowly, and 1944 was the first year in which a majority of deep-mined coal was mechanically loaded.

Jan 1, 1968

By C. K. C. K. Gupta

The rare earths in elemental form are required for a variety of scientific and technological purposes. They are not easily obtained in this form, due to the great chemical stability of the rare-earth compounds and the strong tendency of elemental metals to react with everything they come in to contact with, especially at high temperatures. Beginning in the 1950s, when sufficient quantities of separated rare earths became available, as the result of intense research and development, three processing routes were developed to accomplish the preparation of all 16 naturally occurring rare-earth elements. They are chemical reduction of the halide intermediates, the oxides and electrochemical reduction of chlorides and oxide-fluoride mixtures. Not all the processes are effective with all the rare earths. In spite of the celebrated similarity of trivalent rare earths, the physical properties of individual rare-earth elements are sufficiently different that a variety of techniques are required for their preparation. The development of reduction processes for the rare-earth metals are covered in this paper, with focus on the oxide reduction routes. The strong reliance of effective reduction processes on the fundamental science of reduction reactions is highlighted.

By L. John Minnick

Extraction of crude ores and minerals inevitably produces various by-products either as a result of nonusable residues or as waste by-products from process operations. Thus for each 100 tons of coal extracted in a strip mine operation, one can expect to produce 25 tons, or more, of mine refuse. In addition, the amount of ash produced from the burning of coal will represent 10 to 20 percent of the weight of coal burned. With the advent of lime/limestone scrubbers now being installed on many power plants, an additional by-product is produced that in most instances is equal in volume to the sluiced fly ash. Statistics developed by the National Ash Association have indicated that sluiced waste from power plants in the United States currently exceeds 25 million tons per year (dry basis). Overall mineral industry statistics (copper mines, etc.) indicate better than 200 million tons per year. In the past it was general practice to send most of these waste materials to holding ponds or lagoons simply as a means of disposal or "throwaway" of unwanted by-products. Unfortunately modern society has reached a stage where these large quantities of waste materials are creating monumental environmental and economic problems that need urgent attention. Among these problems are concern for loss of future usable land, pollution of ground water, loss of potential mineral reserves, and loss of opportunities to recycle or use these by-products for the benefit of future generations. An example of the latter is the serious shortages of construction quality aggregates that can be replaced with some of the by-products produced from waste materials from the extractive and chemical industries.

Jan 1, 1975

By D. M. Walters, C. M. van der Vyver, L. J. deVulliers

The occurrence of underground fires in narrow tabular ore- bodies where high density timber support is used is a dangerous and disruptive occurrence. The containment and extinguishing of the fire remains a very important consideration in reducing not only the loss in production time but also in limiting the extent of the area damaged by the fire. Mindful of this, Gold Fields have adopted and developed the inert gas generator system from its origins in Poland for use in Group precious metal mines. The system generates an oxygen- deficient atmosphere which is introduced in the fire area after this has been sealed. A number of problems had to be overcome to operate this system successfully within the infrastructure of these mines. Of particular significance is the operation of a jet engine, the prime component of the system, at air pressures encountered below sea level. The modifications have been found to be satisfactory to the point where, since 1992, ten underground fires have been extinguished using this system. Invariably, the areas affected by these fires were extensive (over 1 000 000 m3) and required continuous operation of these units over extended periods of time (in some cases in excess of 400 hours).

Jan 1, 1997

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, despite its natural abundance, demand for coal exceeds its countrywide supply due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98 percent of total raw coal production in the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an environmentally friendly manner, especially in populated areas adjacent to the mining zone. This technology eliminates blast hole drilling, blasting and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks.

May 1, 2023

By Gerald C. Smith

Carlin Gold Mining Company is a wholly owned subsidiary of Newmont Mining Corporation and is located 76 kilometers north west of Elko, Nevada. Multiple bench open pit mining methods are being used to mine 24.5 Mt of ore and waste per year. Mining started in 1964 and up through 1983 Carlin has mined 138 Mt of ore and waste and has milled 13.8 Mt of ore. Selective mining of carbonaceous and oxide ores together with a good grade control program have been key factors in the success of the operation. This paper will present the raining methods and the mining equipment being utilized to make Carlin Gold Mining Company a very profitable operation while mining and milling low-grade gold ore.

Jan 1, 1985

By J. T. Kline

This paper will present a review of the underground leaching of remnant copper mineralization left as a result of the block cave mining operation at the Lakeshore Mine in Casa Grande, Arizona.

Jan 1, 1985

By R. Q. Honaker

Although the fundamental principles of hindered bed classifiers are relatively simple, the complex interactions between the operating parameters provide a degree of difficulty that hinders the ability for on-line plant optimization. Thus, a dynamic population balance model was developed for determining the hindered settling velocity of particles varying in density and size. The steady-state results of the model include partition curves as a function of particle size and density as well as metallurgical data. A statistical comparison of the simulation results with those obtained from industrial units reveal a high level of accuracy with adjusted R2 values greater than 0.95.

Jan 1, 1999

By R. J. Lutton

The U. S. Army Corps of Engineers is seeking empirical slope data from mining companies and other organizations to help establish guides for engineering Judgment in crater excavation for canals and other civil works. Slopes from about 100 open pits and other excavations range in heights to greater than 1000 ft. Factors known or expected to affect stability (and optimum slope inclination) are: geological structural orientation, geological structural ordering, method and technique of blasting, design life of slope, groundwater conditions, depth of excavation, climate, and height. These and other more subtle factors appear to combine and produce an overall effect brought out best on a family of empirical curves relating slope height and inclination.

Jan 1, 1968

By Erik S. Bernard

"INTRODUCTION Conventional steel bar reinforcement is used in many tunnel linings to provide high flexural and tensile load resistance. These Reinforced Concrete (RC) tunnel linings may suffer flexural cracking during service or, in the case of precast concrete segments, during production, handling, or installation. Cracks can lead to corrosion of steel reinforcement, so limits are placed on maximum acceptable crack widths to reduce the likelihood of corrosion during the intended design life (AFTES, 2013; MC2010, 2012). However, the relatively light level of reinforcement used in many applications can result in quite wide in-service crack widths, so either additional steel bar reinforcement is required to limit maximum crack widths, or fibers can be included to control crack widths. Numerous investigations have been undertaken into the efficacy of including steel fibers to reduce crack widths in conventionally reinforced members (Stang and Aarre, 1992; Abrishami and Mitchell, 1997; Bischoff, 2003; Dupont and Vandevalle, 2003; and Jansson et al, 2010), but steel fibers suffer the problem that they are at least as sensitive to corrosion at cracks as steel bars and therefore have similarly tight limits placed on acceptable crack widths (AFTES, 2013). An alternative means of maintaining narrow crack limits in RC members has therefore been sought. The current investigation was instigated following an observation that theories promoted as an explanation for the ability of steel fibers to reduce crack widths in reinforced concrete flexural members (Deluce et al, 2014) do not depend on the material composition of the fibers used but instead depend primarily on the tensile stress generated by the fibers across cracks. Since it is known that macro-synthetic fibers are capable of equaling the post-crack tensile capacity of steel fibers, it has been hypothesized that macro-synthetic fibers are also capable of reducing crack widths in reinforced concrete flexural members but with the added advantage that macro-synthetic fibers are completely immune to the effects of corrosion. Use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete flexural members subject to aggressive environmental exposure is more rational than use of steel fibers because steel fibers are very sensitive to the corrosive effects of environmental exposure at cracks. The current investigation was therefore undertaken to explore the potential use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete members subject to flexure. Barchip BC54 fibers were selected as they are one of the most widely used and competitive high performance macro-synthetic fibers currently available."

Jan 1, 2016

By Terry L. Muldoon

On July 7, 1971, noise regulations for underground coal mines were implemented under provisions set forth in the Federal Coal Mine Health and Safety Act of 1969. These same regulations now also apply to coal mine surface facilities. In August 1971, in anticipation of these regulations, the Bureau of Mines, through the cooperation of the mine operators, conducted extensive noise surveys in three coal cleaning plants. The survey was conducted in an attempt to identify those occupations where exposures would exceed the proposed regulations.

Jan 1, 1972

By Mirza Muhammad Zaid, Nana A. Amoah, Ping Chang, Guang Xu, Ashish R. Kumar

The key takeaway of this study is the significant improvement in dust protection for roof bolter operators in underground coal mines. The optimized canopy air curtain (CAC), with a redesigned two-level manifold system, provides uniform airflow distribution that effectively reduces dust exposure. By enhancing the protection of operators from harmful respirable coal and silica dust, this technology can reduce the risk of diseases such as coal workers’ pneumoconiosis (CWP) and silicosis. The application of this optimized CAC design in real-life coal mining operations can dramatically improve worker health and safety by minimizing dust-related exposure, ensuring compliance with industry regulations and prolonging the lifespan of mining equipment by reducing dust accumulation.

Dec 1, 2024

By Robert D. Deister

The Buick Concentrator represents state-of- the-art technology in automated digital process control operation utilizing a centralized computer. The process control strategies implemented at Buick are no longer new to the industry but the successful application of these developments is still rather unique in North America. Productivity improvements, determined to be a direct result of the process control developments, are the primary topics of this paper. Emphasis is placed on metallurgical benefits including both lead and zinc recoveries, lead concentrate grade and reductions realized in reagent consumptions, operating costs and personnel. The productivity improvement discussion is preceded by a concentrator description and a brief history of the process control development at Buick. Current control strategies and future applications are presented afterward.

Jan 1, 1985

By Heinz C. Dittmar

The phenomenon of radioactivity has been known since the turn of the last century. Scientists of many nations, intrigued by the strange effects of radioactivity, have engaged in research to probe the heretofore presumed, but largely unknown world of atomic structures and subatomic- particles. A theory evolved of splitting the atom, thus providing insight into the structure of matter and opening the way to possibly create new materials. Many years of effort culminated in the first chain reaction in 1942. The beginning of the atomic age was drastically demonstrated by the flash of the large scale chain reaction of the first atom bomb. It was actual proof of the incredible energies contained in matter.

Jan 1, 1966