Search Documents

By Achille Balossi Restelli, Elena Rovetto, Andrea Pettinaroli

"The Station “C13” of Warsaw Underground Line II, with tunnel crown 10m below the water table, required the excavation of three connection tunnels, underpassing a six-lane in service road tunnel, working from two lateral shafts. After the collapse occurred while digging the first tunnel, the use of artificial ground freezing was chosen to ensure the excavation under safe conditions. A complex freezing pipe geometry and excavation sequencing was necessary because of the interferences of the overlying road tunnel diaphragm wall foundations, shaft internal structures and previous grouting activities. A combined freezing method was used: nitrogen for freezing the tunnel arches, brine for freezing the intermediate wall and for maintenance stages. Sandy and silty sandy layers were frozen around the crowns and sides. No treatment was necessary for the inverts, lying in clay. A monitoring system of ground temperatures and structure movements allowed for successful completion of work in 8 months. INTRODUCTION The C13 Station of the Warsaw Underground-Line II is located on the West bank of the Vistula River. It consists of two shafts and three connecting tunnels, passing under the Wislostrada (WS) Road tunnel. According to the initial geotechnical investigation, tunnels should have been excavated in high-plasticity clay, but during the first borings non cohesive soil was encountered. Additional investigations were performed on both shafts and a more detailed stratigraphy was reconstructed (Lombardi et al. 2015). Layers of fine sand, sandy silt and sandy silty clay were present along the tunnels crown arches and in the North East tunnel they extended down to the centre line (-13.735m above the Vistula River medium level). Based on the new stratigraphy, it was decided to stabilize the crown and control the groundwater inflow from the face with jet-grouting columns extending the treatment down to the clayey soil, but a collapse occurred in the North West tunnel with soil and water inflow inside the shaft."

Jan 1, 2016

By NARAYAN K. BHAGAT, ARVIND K. MISHRA, Aditya Rana, M. M. Singh

The paper presents an innovative directional controlled blasting (DCB) technique for excavating unstable slopes along the Konkan railway in India without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw were developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3, irrespective of the actual free face, was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle was changed from 80–82 to 45–47 degrees, and possible wedge, planar and toppling failures were eliminated. No incident of rockfall and slope failure along these slopes has been observed after the stabilization.

The need for an integrated approach to optimization of unit operations in both the pit and the mill has long been recognized, but the complexity and nature of the overall problem has up to now resisted solution. This paper reports on a modeling methodology which couples symbolic and numeric computing to unify operations in both the pit and mill. The ultimate goal of this work is to optimize all operations that are influenced by blasting. Blasting plays a key role in all facets of operations. Obviously, drilling and blasting costs are determined by blast design, but the down-stream costs that are closely related to blasting results are often treated as separate functions: loading, hauling, cleanup, and crushing and grinding are all heavily influenced. Diggablilty and bucket fill factor are a function of fragmentation, the condition of the floor and uniformity in the shape of the muck pile. Likewise, cycle times and loading delays partially determine haul cycles, while fragmentation distribution and size determines the efficiency of truck loading. Removal and breakage of oversize causes loading delays and increases cleanup costs. The influence of blasting doesn't stop at the crusher. Mill productivity, power consumption, and maintenance are a function of the feed. Even at the SAG mill a reduction of a critical particle size during blasting can increase throughput. Thus, a bottle-neck for production far removed from unit operations in the pit can be alleviated by a modification in blast design. The question is: how do we optimize blasting with respect not only to itself but to al\ related mining and milling operations? For that matter, how do we even model blasting so that we can control the results of a blast?

Jan 1, 1991

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive, and it is quantified as a confined or unconfined velocity. The confined velocity is more significant as explosives are usually used under a definite degree of confinement. This study evaluates the stepwise increment of the air-deck volume from 10 to 30 percent, and its effect on the VOD. The VOD estimation in the 172-mm-diameter explosive column was conducted using the Dáutriche technique. The air-deck volume increment has an attenuation effect on the steady-state VOD, and detonation failure is high at 30 percent air-deck volume. This attenuation effect is directly linked to the explosive’s rating and efficacy. The air-decking approach in this study is different from conventional air-decking techniques in that it does not employ the fixed blasthole parameters, air-deck volume and specific VOD. 

Despite two large projects represented in the keynote docket, the mood of the 2011 SME Arizona Conference was summed up best by Ferol Baker, general manager of New Mexico Copper Corp. (a wholly owned subsidiary of Themac Resources Group), ?In the past, it seemed like you couldn?t go to a conference like this without hearing about one big new greenfield project after another. Now what you see is companies doing internal expansion or small-scale brownfield development.? Overall, the tone of this year?s meeting, held at the J.W. Marriott Resort at Starr Pass in Tucson, AZ, was upbeat, yet practical. From the keynote and luncheon addresses to the six panels of sessions, the projects described were positive about the future, yet focused on the details required to make those projects come to fruition.

Jan 1, 2012

When I wrote the Railroad portion of "Mining Engineering" magazines 94 Powder River Basin (PRB) Coal Article I described to you some definite destinations the Railroads had in mind. As with many destinations, the ones I wrote of turned out to be merely stops on the way to places that we have yet to reach. Somewhere along the way we discovered that making it better is a continuous process not just something that you can do in phases I, II, III, & IV. We always knew this I suspect, but perhaps not at the awareness level that exists in RR environments in 1997. The purpose of this article is to update the 94 article, which I could do very quickly. Everything I told you we were going to do in 94 is done, end of story! But in addition to making it a very short article it would not be telling you the things RR has done beyond what we were planning in 94 and for the future.

Jan 1, 1998

Several major impediments threaten the successful delivery of tunnel and under-ground construction projects. In addition to technical design and construction risks associated with tunnel projects, many of which are well understood, budgetary pressures, funding constraints and the complexity of procuring, administering and executing multiple concur-rent projects in a large program could also have a catastrophic impact on the program?s objectives. Contributing factors often include poorly managed design, procurement, construction, managerial, organizational, market and stake-holder risks, as well as nonconforming inputs or outputs to the costs and schedule, or any other potential inabilities to deliver the required or desired results. A strategy to prevent ?failure? of a project requires a proactive and holistic approach to risk management. Through planning, identification, analysis, management, monitoring and control of the project?s risks (both threats and opportunities), attention to management of risk will in-crease the probability and impact of positive events and decrease the probability and impact of events adverse to a project?s objectives.

By J. J. Moore

Combustion synthesis, or self-propagating high-temperature synthesis (SHS), reaction systems are discussed with respect to thermodynamics and kinetics. In particular, the effect of the process parameters, e.g. particle size, [All] ignition and combustion temperatures, on these self-sustaining reactions is discussed. Combustion theory is used to investigate the effect of the overall actuation energy of the SHS reaction on the combustion front propagation rate and in obtaining a clearer understanding of the transition from stable to unstable propagation. Finally, examples of the application of combustion synthesis to advanced materials processes are made, in particular the synthesis of Ni-Ti-X intermetallic shape memory alloys, TiC-AI2O3 and ZrB2-AI203 ceramic composite materials.

Jan 1, 1992

By A. E. Ketler

Optical smoke monitoring fills an important gap in ventilation and fire safety: namely monitoring of smoky, low temperature fires where little CO and heat are generated. Smoke monitoring also avoids the nuisance alarms due to diesel exhaust, battery chargers, blasting and welding. The smoke optical density (OD) fire alarm standard specified by MSHA presents an opportunity for improved safety. Experience of actual mine usage of the SmokeBoss*100 is reviewed, with particular regard to effectivity, maintenance and cost.

Jan 1, 1995

By III Scotland

Genstar's underground mine at Texas, MD experienced a failure of the mine roof and subsequent damage to an underground backfill caused by surface floodwaters. A hydraulic backfilling program was developed in house to stabilize temporary repairs to the mine roof, replace 2300 yards of pneumatically stowed backfill, and complete a permanent repair to the mine roof. A flowable backfill material was developed, tested, and later marketed as the result of experience gained during this project. In addition, Genstar personnel developed backfilling techniques to meet the requirements of the repairs and completed work without the additional expense of non company services or contractors.

Jan 1, 1992

By K. N. Han, K. Peri, Y. Guan

The leaching behavior of gold in ammonical solutions with iodine as an oxidant was investigated using cyclic voltammogram and Tafel polarization. The majority of the experiments were carried out at 75°C, and the results were compared with consideraton given to the equilibrium of the iodine-ammonia system. The distribution of nine iodide-containing species at various pH values in the absence and presence of ammonia were considered at three different temperatures. It was found that, with the introduction of ammonia into the system, the concentration of iodide (I-), iodine (I2) and triiodide (I3-) is increased substantially, which in turn helps the rate of gold dissolution. The apparent activation energy was found to be about 46 kJ/mole, indicating a chemical-controlled mechanism.

Jan 1, 2002

By M. D. Bath

Minproc Engineers Inc. (Minproc) recently completed the construction and start-up of a process facility to treat 14,000 t/d of gold-silver ore at Kori Kollo, Bolivia. The comminution circuit consists of crushing and SAG-ball mill grinding. Breakage characteristics of the ore were determined and a circuit model developed. This enabled variations of the circuit to be simulated, and evaluated in terms of predicted performance to provide the criteria for final engineering design. Subsequently, analysis of the operating circuit provided data for circuit model-fitting. The validity of the original model and circuit performance predictions are discussed.

Jan 1, 1994

By Mogens Henriksen

In the past decade, numerous urge scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in Figure 1. Allen1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs2. His data, however, do not reflect sensitivity of flowrate to air/water ratio. Further, in Gibbs' work, air apparently is injected continuously along the column of water. This configuration differs from that used in reverse air lift drilling where air is injected at discrete points only. Gas lift theory has received considerable attention over the past decades. Orldszewski3 defined flow regimes in two phase flow. Griffith and Wallis4 determined relative velocities of gas to liquid. Two-phase flow has been studied extensively for oil transport in inclined and vertical pipes by Chierici et a15, Beggs and Brill6, and Gould, Tek and Katz.7

Jan 1, 1977

By William Gleason

With more than 20 major mines extracting copper, gold, coal, molybdenum and lime, Arizona is recognized as one of the better mining jurisdictions, not just in the United States, but in the world. However, that is not to say the road to production is always paved with gold, or in many cases, copper. Earning the license to mine in Arizona is a complex process with years of paperwork and permitting before the first tons of ore are ever processed. Now, get the federal government involved and the process becomes even more complex, and the path to production can become even longer.

Jan 1, 2013

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata

"Rock tunnels suffered severe damage from recent large earthquakes in Japan, despite the empirical knowledge that tunnels tolerate earthquakes better than surface structures. Seismic design for rock tunnels have therefore become a fascinating subject for many tunnel engineers. However, even basic behavior, including deformation mode and loading magnitude for hard-rock TBM tunnels and conventional ones during earthquake, has not been fully understood due to lack of actual seismic data; while EPB and slurry TBM tunnels take account of seismic design in Japan if needed. This study conducted a dynamic measurement in an actual road tunnel constructed in rock. The strongest aftershock of “the 2011 off the Pacific coast of Tohoku Earthquake” (Mw = 7.1) occurred during the measurement, providing precious data to examine deformation mode of the tunnel. Considering the acquired data, numerical analysis was also performed to calculate loading magnitude to cause fatal fracture of tunnel lining during earthquake.INTRODUCTIONLarge earthquakes can pose serious risks even for rock tunnels, as evidenced by large earthquakes in the past. In the large earthquake in Japan in 2004 (Mw = 6.6), some tunnels suffered severe damage including collapse of their permanent lining (Mashimo 2005), even though the tunnels were constructed in ordinary ground conditions except for fault, fracture zone, portal area, etc. To mitigate such risks, mechanical behavior of tunnel lining during earthquake should be clarified; however, even basic mechanical behavior including load-bearing capacity of the tunnel lining against earthquake is not fully understood.Numerous damage modes were actually observed due to various ground conditions (eg. Wang et al. 2001; Mashimo 2005). Among them, major tunnel damage caused by earthquakes can be grouped into three main modes as shown in Figure 1, excluding extremely unusual conditions such as a tunnel located on a stratum boundary where the stratum stiffness varies significantly. TYPE-I shows flexural failure or crack by bending moment at shoulders; TYPE-II indicates compression failure or flexural compression failure at crown; and TYPE-III illustrates compression failure at sidewall, mainly observed on tunnel that was constructed using steel ribs and lagging method. These damage modes, Type-I, II and III, are predominantly caused by shearing, horizontal compressing and vertical compressing deformations of the surrounding ground, respectively (Kusaka et al. 2011; Asakura et al. 2001)."

Jan 1, 2016

By R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al (III) and flotation collectors. It was found that the presence of Al (III) is necessary for good flotation of the organism whether or not Pb(II) is present when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8 and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al (III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminoproprionic acid is used as collector good flotation occurs at about pH 4 without the addition of Al (III).

Jan 1, 1990

By Y. J. Wang

This paper describes a procedure for solving the generalized system of n network equations in n unknowns considering the following ventilation variables and parameters: (a) air quantities, (b) pressure losses or gains caused by the control devices (i.e., fans or regulators), (c) resistance factors, (d) natural ventilation pressure, and (e) fan pressures (as a function of air quantities). The air quantities and pressure losses for all branches in the network are grouped into dependent and independent variables. The branches with an independent quantity are contained in a chord set, and the branches with a dependent pressure loss are contained in a chord set. In addition to the problem formulation, the solution procedure, applying the Newton method, is discussed and illustrated with a numerical example.

Jan 1, 1989

By J. P. Matoney

The operation of a modern coal preparation plant, particularly in western Canada, is a very complex task. Most western Canadian operations are processing two or more, sometimes up to ten, different seams through the same plant. This requires a sophisticated multi-circuit plant that needs close operational control. Add the soft nature and large amounts of natural fines of western Canadian coal and you have a formidable cleaning task. To assist in the operation, programmable controllers and sophisticated control concepts are being more widely used. Two of the newest coal preparation plants in Canada have been designed by Raymond Kaiser Engineers Inc. and its Canadian subsidiary, Phillips Barratt Kaiser Engineering, Ltd. The use of programmable controllers and control systems will be illustrated by showing their application in a "typical" western Canadian coal plant. This example will cover flowsheet design, control concept systems application, and possible future uses.

Jan 1, 1983

By Aaron Jones, Guy Reed, Russell Frith

"In 2017, one of the international authorities on coal bursts, Dr. Chris Mark, published a paper entitled “Coal Bursts that Occur during Development: A Rock Mechanics Enigma,” in which several relevant technical issues were identified, the most pertinent being:i.whilst development coal bursts are commonly associated with geological faults, understanding which specific faults result in burst-prone development mining conditions and why, remains undefined.ii.conventional wisdom in relation to strong roof and floor geology of the coal seam might be limiting, based on certain burst examples in Colorado.iii. development coal bursts can occur without the local ground stresses being substantially elevated from their in situ levels.This paper outlines what is considered to be a credible, first-principles, mechanistic explanation for these three current development coal burst conundrums by reference to early published coal testing work examining the significance of a lack of “constraint” to coal stability and an understanding of how very specific structural geology and other geological features can logically cause this to occur in situ, albeit on a statistically very rare basis. This basic model is examined by reference to published information pertaining to the development coal-burst that occurred at the Austar Coal Mine in New South Wales, Australia, in 2014 and from the Sunnyside District in Utah, USA.The “cause and effect” model for development coal bursts presented also offers a meaningful explanation for the statistical improbability for what are nonetheless potentially highly-destructive events, being able to explain the statistical rarity being just as important to the credibility of the model as explaining the local conditions associated with burst events.The model could also form the basis for a robust, risk-based approach utilising a “hierarchy of controls” to the operational management of the development coal burst threat. Specifically, these include the use of pre-mining predictions for likely burst-prone and non-burst-prone areas, the use of the mine layout to avoid or at least minimise mining within burst-prone areas if appropriate, and finally the development of an operational Trigger Action Response Plan that reduces the likelihood of inadvertent roadway development into a burst-prone area without suitable safety controls already being in place."

Jan 1, 2019

By Morgan M. Sears

The LaModel program is widely used to calculate stresses and displacements on thin tabular deposits, particularly when multiple seams or complex mining geometry is encountered. The program itself allows the user to create multiple mining steps to show a progressive sequence of mining. However, LaModel considers each individual step as an independent steady-state condition, and any previous loading conditions of the materials are not tracked. It also does not consider any sort of dynamic stress change during the mining process. In certain circumstances, especially in multiple-seam situations, modeling a scenario of the seam of interest without considering the previous mining sequence in the off seams can potentially lead to inaccurate results. The primary objective of this paper is to present a situation where a potentially dynamic, unstable mining condition was encountered. It was not evident until the previous loading conditions in the off seams and the impact of dynamic stress changes in the active seam were considered. It is important to make the mining community aware of these potential modeling scenarios where the path-dependent nature of the mining sequence is of key importance. This paper presents a case history where room-and-pillar retreat mining was being conducted in a relatively deep cover stress regime where multiple seam interactions were present from both undermining and overmining. Mining in the active seam was being conducted with roomand- pillar mining techniques consisting of a series of parallel production panels being successively developed and retreat mined along a set of Mains. In this situation, the traditional global LaModel analysis without any path-dependent adjustments did not fully identify the area of poor conditions that were encountered. This paper explores the impacts of mining in the active seam on the lower seam which, in turn, has a negative impact on the active seam. This provided a solid foundation for the subsequent analysis of the three seams simultaneously. Based on the calibrated model, it is likely that retreat mining in the active seam resulted in increased stresses in the underlying seam that conceivably resulted in additional convergence and, most likely, additionally convergence of the pillars under the panel being developed. This in turn could have caused active subsid- The LaModel program is extremely useful for analyzing multiple-seam mining scenarios. As multiple-seam situations become even more prevalent, the potential for encountering a path-dependent mining scenario also increases. To successfully model path-dependent mining scenarios, the ground control engineer will be required to make sound judgments on the condition of pillars in sub-adjacent seams. These engineering judgments should be based not only on the current state of stress, but also on any prior or future states of stress. This means considering the stresses from over or undermining as well as stresses applied to the sub-adjacent seams from actively mining the seam of interest.

Jun 25, 2024