Search Documents

By T. C. Canter

Technological change is continually affecting the mining industry and the many papers being presented at this meeting reflect this fact. I fully agree that miners must remain fully cognizant of technology that can change mining costs and therefore your competitive marketplace. Despite the embrace of new technology and effective mine management techniques, the mining enterprise may not realize increased net income if the structure of the minerals marketplace is not understood. An important segment of the marketing structure for minerals is transportation. Transportation costs per ton can be much greater than the mining costs per ton and may accordingly overshadow hard earned gains in productivity. Change is greatly affecting the transportation industry but the change is driven more by governmental policy than technology. Although some technological advances are occurring in the bulk transportation business, the changes I want to address arise from policy. Policy changes have come from legislation in the 1970's culminating with the Staggers Act of 1980 and ensuing Interstate Commerce Commission decisions.

Jan 1, 1985

By M. W. Brandt

In the November 1957 issue of "Chemical Process Engineering," a British publications, there appeared an article entitled "Correct Selection of Drying Equipment." The author wrote as follows "Whether batch drying or continuous drying' methods are applied, the basis of efficient drying is heat distribution, control of rate of heat input, and heat transference from heating medium to the particles of the material to be dried." The author continues: "Because the efficiency of direct dryers, such as hot air or hot gas dryers, increases with rising inlet temperature of the drying air or gas when exhaust temperature remains fixed, the highest practical drying temperature should be used. Exhaust air should leave the dryer at the lowest possible temperature, but as fully saturated with moisture as possible." It is certainly conceivable that the author of this article by outlining the basic requirements for efficient drying methods has unwittingly given the reasons why fluidized drying is rapidly being adopted for so many industrail applications, including the dryingof fine coal. An examination in greater detail of the individual basic requirements for efficient drying as outlined by the author is perhaps the most logical starting point.

Jan 1, 1958

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001

By Ashis Bhattacherjee, Rahul Upadhyay, Nearkasen Chau, Aditya Kumar Patra, Dhanjee Kumar Chaudhary

Heavy earth-moving machineries used in openpit mines intensively expose drill operators to whole-body vibration and shocks, and thus to musculoskeletal disorders. The roles of individual, machine and rock-related factors in their exposure remain poorly understood. This cross-sectional study investigated their roles in 39 drill operators from Indian iron ore mines. It shows that 70 percent of the operators were exposed to high levels of vibration, above the limit values recommended by ISO 2631-1 (1997). Multiple linear regression models showed that the whole-body vibration and shock exposures were strongly associated with operator’s age, drill-machine model and rock hardness, uniaxial compressive strength and density. The role of body mass index was close to significance (p = 0.08). Univariate analyses found the drill’s age, seat-pad thickness and seat backrest height were also strong predictors. These results help in identifying risky operators, materials and occupational situations, and in implementing appropriate prevention and intervention strategies to reduce and monitor the exposures and health risk. In addition, during the planning stage of acquisition of new equipment, anthropometric data of the operators should be considered for the ergonomic design of the seat.

Caterpillar unveiled a new dozer, the new Cat D10T2 dozer, that builds on the success the company has had with its D10T model. The newest version of the dozer includes refinements to its power train, automated controls and structures. The result, the company said, is high productivity with superior fuel efficiency, reliable operation with long-lived structures, as well as enhanced access for service technicians and operators. The D10T2 uses the latest load-sensing hydraulics technology combined with Cat advanced engine controls to maximize the amount of material moved for every drop of fuel burned. Improved filtration protects the fuel system, hydraulic system and power train oil system to help ensure high reliability and minimal machine downtime. Refined large structures, such as redesigned track roller frames, deliver longer service before rebuilds. Improved access and egress features enhance safety and productivity of technicians and operators, and optional powered access systems and platforms enable configuring the D10T2 for the site. Caterpillar offers the D10T2 with two variations of the Cat C27 engine with ACERT Technology. One version is U.S. Environmental Protection Agency (EPA) Tier 4 Final certified, and the other is capable of achieving emission levels equivalent to EPA Tier 2 standards. Both engine configurations produce net power of 447 kW (600 hp) in forward gears and 538 kW (722 hp) in reverse gears. The engine controller automatically adjusts power output based on the direction of travel. With the new system, the D10T2 has about 20 percent more power in reverse compared to its predecessor model. The result is faster cycle times and greater productivity in certain applications. The D10T2 is suited for a variety of applications including mining, heavy construction and bulk materials handling.

Mar 1, 2014

By Bruce E. Holbein, Dennis K. Kidby, Ann L. Huber

World gold production figures and the processes used for gold production indicate a high dependence on both cyanide leaching and carbon adsorption metallurgies. Problems associated with the use of carbon in the treatment of refractory ores as well as economic and environmental considerations associated with the use of cyanide point to the advantages that can be realized through the use of more efficient gold adsorption media and with cyanide recovery. We have developed a process termed AurosaveTM-1 which provides a number of advantages through the use of a new synthetic robust gold adsorption medium, termed Vitrokele TM V-911. This process allows further recovery of gold from a variety of ores and allows for a simplified process for use not involving thermal regeneration or high pressure elution. We have also developed a cyanide recovery process termed Cyanosave ™ which uses Vitrokele TM V-911 and allows efficient recovery of cyanides from decants or tailings and re-use of recovered cyanide. This obviates the high chemical expenses for cyanide destruction where environmental issues require such water and tailings management.

Jan 1, 1998

By B. Kolonja

This paper considers simulation of truck dispatching system designs using maximum expected production of the truck-shovel system as the measure of performance. Two methods are utilized, multiple comparisons with the best (MCB) and the combination of MCB and the variance reduction technique known as common random numbers (CRN). These two techniques are compared via simulation experiments. The results show that the combined procedure of MCB with CRN is the superior tool to reduce the total number of replications needed to ensure the specified probability of correct selection over the finite number of designing systems. In this case study, MCB with CRN reduces the variance by 29% and the number of required replications by 48%. Also, the MCB with CRN procedure narrowed the confidence interval by 18%.

Jan 1, 1994

By Stuart K. Nicol, Malcolm D. Engel, Neville T. Moxon

Ion flotation of gold is a process continuing to be developed to selectively beneficiate dilute aurocyanide liquors using a novel surface­active complexing agent. Aeration of these liquors causes accumulation of the precious metal species in the froth concentrate produced in a flotation column. Successful development of ion flotation for concentrating solids-free liquors would offer a low--cost method for recovering specific metals from heap leach runoff or waste tailings solutions. The cost of constructing and operating a 100 tph gold ion flotation facility has been compared with the relevant carbon adsorption plant costs. Reductions in operating costs of 25% and installed capital of 40% are possible in relevant expenditure areas. For an 'average' processing plant, this equates to annual operating savings of A$ 170 000 and a capital saving of A$ 515 000, with a three-point increase in total (mine and plant) site DCF ROI. High gold inventories are eliminated and the number of processing steps is reduced. The application of gold ion flotation will initially be confined to heap leach operations in the western U.S.A., although use of the process in mine abandonment programmes elsewhere is also an area of future development.

Jan 1, 1992

By J. I. Adetunji

Mining activities usually affect the soil, subsurface layers, water resources, the atmosphere and in general the lives of the people. The effects can be mechanical, biological, ecological and economical in nature and these effects can be characterized by their intensity, frequency, duration and scale. In Oyo State, Southwestern Nigeria efforts are being made to employ a sustainable method in the exploration and exploitation of abundant industrial minerals present in the state. The minerals exploited include talc, clay, marble, sillimanite, tantalite, niobium, beryl, tourmaline aquamarine, rock aggregates, etc. Results of this sustainable approach show that the environmental impacts of surface and underground mining of industrial minerals are not spread far beyond the mines site acreage. More lands are being reclaimed, the amount of dust released into the air has been minimized, the quality of sewage waters produced during operations are minimized, top soils removed during subsurface mining are preserved, the tonnages of minerals exploited are being monitored and controlled. All these point to a positive development in practicing sustainable methods in mineral exploitation to meet the developmental needs of the Oyo State at present and to conserve for the future.

Jan 1, 2003

By Terry O. Arney

Ore Reserve Models are well established evaluation and mine planning tools. BY definition, these models are made up of regularly sized blocks, arranged in a three dimensional matrix. Two dimensions correspond to north and east directions, and the third, to the depth or elevation. The dimensions of the blocks need not be equal, but generally at least two of the dimensions are equal. The blocks are located in space by coordinates which are generally translated into index values for computer applications. Each block will have quantitative attributes, such as grades, densities, rock characteristics, etc. assigned to it. The process of assigning values to each block in the three dimensional matrix is the process of ore reserve model development. One of several interpolation procedures may be employed to predict the value of a block, based on surrounding data. Block value models have several uses. The utilization of block models in ore reserve computations is quite common. Here, ore reserves may be calculated by level or by cross-section for the entire deposit. For each ore reserve calculation, multiple cut-off grades may be analyzed to determine the ore reserves under different cut-off conditions. The other major use of block value models is in mine simulation. Through simulation, profitable studies that analyze the effect of alternate ore removal sequences can be undertaken to determine economic optimality. Other studies that are undertaken in mine simulation problems include the evaluation of mine layout, pit slope effects, and the impact of varying cut-off grades.

Jan 1, 1974

By K. Perry, R. Eades

"Highwall miners continue to be implemented by operations to increase recovery, improve margins, and justify higher stripping ratios as high quality surface reserves become increasingly rare. Many times, operations facilitate projected underground operations by leaving an intact highwall for development purposes. These facts result in larger highwalls that are left standing for increased periods of time prior to reclamation. As a consequence, worker exposure and risk is also elevated, resulting in higher potential for accidents or fatalities relating to surface highwalls. Highwall stability is a complex issue, dependent on both geologic and mining factors. Dynamic numerical modeling offers the capability to assess possible stability issues related to blasting-induced ground vibrations. Research has been conducted to evaluate the effect of highwall stability due to ground vibrations from blasting events. Additionally, the relationship of amplitude and frequency, and their impact on highwall stability is investigated. The results of this modeling indicate that amplitude has little impact on stability. However, frequency has a significant impact on highwall stability. INTRODUCTION The number of mining fatalities has declined since 2010, and 2016 is currently on pace to continue this trend (MSHA 2016). This decline can be directly correlated to the decline in surface mining activity and the overall decline of the coal industry. However, since 2002 the percentage of surface coal mine fatalities associated with highwall activities remains relatively high, constituting approximately 15% of all surface mine fatalities. 2014 was the first year with a highwall failure fatality since 2011. Most recent surface coal mining fatalities are associated with machinery and haulage. Table 1 provides a summary of the total surface coal mining fatalities, and the number of highwall failure fatalities dating back to 2010.Highwall stability is a complex issue, dependent upon geology and geologic discontinuities within the rock mass, along with highwall geometry, standing time, and applied stresses. Another possible concern that has not been previously investigated is the effect of blasting-induced stresses on highwall stability and the stability of web/barrier pillar systems as a result of ground vibrations from blasting events. Many modern surface coal mines employ numerous extraction fronts that rely on blasting for primary rock breakage. This results in highwall and highwall pillar systems experiencing blasting-induced stresses of many different types and magnitudes."

Jan 1, 2017

By T. W. Camm

One function of the U.S. Bureau of Mines is assessing potential economic impacts of federal land withdrawal policies. This often requires performing economic ana1ysls for an area with limited geologic information available. Input to the economic decision process relies heavily on estimates of mine and mill costs for the potential resources in the area being considered. A methodology for performing these cost estimates was needed to address this situation.

Jan 1, 1992

By H. Cetin

The availability of coal resources of selected 7.5-minute quadrangles of southwest Indiana was examined in this study. Resources were defined as original coal in place, remaining after mining, and currently available considering land-use and technological restrictions. The amount of coal mined from each study area varies depending on the mining practices of the companies operating within the area. Of the three quadrangle investigations, the available resources range from 50 percent to 79 percent of the original resources. Most of the coal resources under deep-minable category were not available because of technologic restrictions, such as insufficient coal thickness.

Jan 1, 1996

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By Kenneth A. Grace

Each and every mining operation from a simple sand-and-gravel pit to the largest integrated mine-mill-concentrator-smelter-refining complex has, as its foundation, a quantity of extractable natural resource the reserves. Without reserves, there is no mine, and any concentrating or extracting plant, no matter how sophisticated, is simply so much scrap metal. And, of course, without resources there are no reserves. It is remarkable, therefore, especially in this age of careful planning, high quality engineering, and state-of-the-art financial analysis, that such a fundamental and vital item is so little understood and the subject- of so much confusion. Time and time again it has been the experience of the author, when called in to a mining operation that has run into trouble in reaching projected production targets, to find that the designed-for tons were not reaching the concentrator/extraction plant, and/or the grade of such tonnage was substantially below the forecast and design grade of the plant. The mill blames the mine for delivering below standard tons and/or grade and the mining engineer blames the geologist for overly-optimistic assessment or incorrect interpretation of the deposit. The geologist blames the mining and metallurgy division for wrongly interpreting his data and conclusions, or simply fouling-up a fine orebody.

Jan 1, 1983

By C. Anderson, D. Kolstad, M. Unger

Operators are often challenged with the management of water throughout the life cycle of a mine. High water levels can lead to physical or chemical instability of water-retaining structures. Operators need to predict changes in water levels to make timely operational decisions and plan for contingencies, particularly in remote legacy mines. A closed mine in northern Canada with no permanent on-site personnel had a simple water balance model that was effective for decades to inform annual water treatment operations. In recent years challenging water quality and more stringent effluent quality criteria has strained those treatment operations and led to more water being stored. Additionally, the region has experienced more precipitation and higher water levels, which have triggered emergency response activities. A calibrated probabilistic model was used to provide enhanced prediction capabilities and to identify key sensitivities in the water balance for monitoring. A several-year case study shows the value that this modelling tool provided for mobilizing personnel and performing response actions, particularly the inclusion of probability paired with forecasted pond water levels. Annual drawdown targets were subsequently established which provided more certainty in scheduling of annual treatment operations

Mar 2, 2022

By Randal J. Barnes

The nonlinear network optimization algorithm developed in this paper solves the following mine ventilation design problem: find the location and size of all fans and regulators which minimize the overall system power consumption while satisfying all physical, legal, and operational constraints. This work includes the formulation of the problem within the framework of mathematical optimization, the development of the computational theory, and the creation of an efficient solution methodology. The algorithm has been implemented on a microcomputer, and a small but representative example is included. The algorithm presented in this paper has four limitations. First, the optimization process is for a single point in time: the dynamic nature of a mine ventilation system in an evolving mine is not directly addressed. Second, the topology of the ventilation network is required input information. The mathematical algorithm does not optimize the size or location of the mine ventilation airways; however, the post optimality analysis techniques can be used to aid in topological decisions. Third, the problem is formulated using volumetric flow; thus, heat and moisture transfer are ignored. Fourth, the capital cost of ventilation equipment is not included in the formulation.

Jan 1, 1989

By B. T. Field

Pyroprocessing systems range from low temperature dryers to high temperature reactors. The materials and process requirements cover a broad spectrum. It is not the intent of this paper to do a detailed examination of individual processes and equipment, since that can be found in a multitude of other sources; rather it is the intent of this paper to examine the key process variables and offer empirical guidelines to assist in a user?s overall evaluation.

Jan 1, 1998

By L. B. Hales

The advent of the process control computer with its capabilities of monitoring, storage, and real-time control has revolutionized control technology in the mineral industry. Initial efforts to introduce the computer into process control began in the early 1960's. However, it wasn't until the last decade with the introduction of integrated circuits and minicomputers that truly successful applications became visible. Computer hardware and real-time operating software have improved to the point that they rarely provide major problems in the implementation of successful control systems. At this time the most prevalent problems and obstacles affecting the successful implementation of a control system are as follows: (1) reliable and representative sampling systems; (2) rugged and reliable process sensors; (3) the availability of well-defined control strategies; (4) the willingness of plant management to provide the continuous support necessary to acquire and/or train appropriate personnel in the operation and maintenance of advanced control systems. Discussion of these problems and of the instrumentation required for the successful application of computers in minerals processing plants follows. In order to enhance this discussion the remainder of this subsection is broken up into individual mineral processing categories.

Jan 1, 1979

By Allister McLeod

Coal is expected to play a major role in energy supply in the next 20 years. Oil is a convenient and still reasonably abundant fuel. However, its major sources of supply are regions where there is nervousness about political stability. Uranium is a more efficient fuel - but there is a continuing community apprehension regarding its use. What coal may lack in efficiency, it makes up in long term availability and competitive overall cost. Moreover, diversity of source ensures stable long-term supply. In this way, a major role for coal in the world energy scene is assured. Cyclical considerations aside, demand for coal will increase significantly and it will meet a substantial share of new energy demand, replacing oil and gas in major industrial and electric utility markets. By around the year 2000, coal's share of world energy could reach 30% and rival oil as the largest single source of energy.

Jan 1, 1982