Search Documents

By T. G. Melkus

A Setaram C-80 heat flux micro- calorimeter was used to study the surface and interfacial properties of fine coal particles in water containing flotation agents via heat of immersion measurements. Heat of immersion (?Himm) is usually a small exothermic quantity and can be used' to characterize a solid in terms of its relative hydrophobicity or hydrophilicity. The effects of coal type, surface oxidation, mineral matter content, kerosene concentration, and pH on the wetting characteristics were investigated. Results obtained from the calorimetry experiments correlated well with results from independent flotation experiments.

Jan 1, 1987

By A. Newman, A. Brickey

A pesar de que parte del predominio de software de programación de producción a cielo abierto se puede explicar por la preponderancia de la minería a cielo abierto en todo el mundo, hay otros factores que han dado lugar a un retraso en el software subterráneo correspondiente. Explicamos por qué matemáticamente la programación de la producción subterránea es más difícil que su contraparte a cielo abierto y daremos pautas para la investigación en el campo de la programación subterránea.

Jan 1, 2014

By Christoph Wels, Michael Royle, Shannon Shaw

Intrinsic remediation is the effect of natural attenuation mechanisms - dilution, dispersion, sorption/precipitation and biodegradation - reducing contaminant concentrations in ground water to specified levels at predetermined compliance points in the aquifer. Current monitoring and modeling for post closure was used to assess the current and long-term potential of intrinsic remediation of contaminated seepage originating from a large reactive (sulfidic) tailings impoundment near Questa, New Mexico. It is concluded that the natural attenuation mechanisms of precipitation within the tailings (as a result of buffering) and dilution/dispersion within the aquifer are currently active and likely sufficient to reduce contaminant concentrations to below state standards in the long-term. Other natural attenuation mechanisms such as sorption and biodegradation within the receiving aquife4s) were not assessed here, but are likely further reducing contaminant concentrations. Active interception and recovery of the seepage water is being maintained until monitoring demonstrates that intrinsic remediation has successfully achieved the level of water quality control required.

Jan 1, 2000

By Bob Miller

"All industries have parts and equipment that are exposed to some type of destructive wear. Hardfacing is a cost-effective tool that will minimize wear and increase service life. At first glance, hardfacing can be confusing and troublesome. In reality, it is not.Postle Industries, a manufacturer of hardfacing products, has found that the 22 answers to frequently asked questions may help operators select hardfacing products that are most appropriate for their application. The first 10 questions are addressed in these pages, the full list can seen at Mining Engineering online under the Web-Only Content section.1. What is hardfacing?Metal parts often fail their intended use not because they fracture, but because they wear by abrasion, impact, metal-to-metal contact or some other form of wear, which causes the parts to lose dimension and functionality. Hardfacing, also known as hard surfacing, is the application of a buildup or wear-resistant weld metal onto a part’s surface by means of welding to extend the life of the part. The weld metal may be applied as a solid surface or in a pattern, such as a waffle pattern, herringbone or dot pattern, etc.Hardfacing is becoming increasingly important for many industries to protect equipment that is exposed to wear and abrasion including parts used in mining, earthmoving and construction, oil and gas drilling and steel making and forging. Extending the life of wear parts can save thousands of dollars and improve productivity. Hardfacing can be used to recondition parts that have already been exposed to wear and have lost their useful life, or used in the manufacture of new parts to improve their life before they are put into service.There are three main types of hardfacing applications:• Build-up or rebuilding.• Hardfacing or overlay.• A combination of build-up and overlay.2. What base metals can be hardfaced?Carbon and low-alloy steels with carbon contents of less than 1 percent can be hardfaced. Medium carbon and low-alloy steels are very common since they provide higher strength than mild steels and better abrasion resistance. High carbon alloys may require a special buffer layer.The following base metals can be hardfaced:• Stainless steels.• Manganese steels.• Carbon and alloy steels.• Cast irons.• Nickel-base alloys.• Copper-base alloys."

Aug 1, 2016

By Manoj Kumar, Anil Kumar Singh, Prabal Patra, Ashish Agrawal, Souvik Ghosh, Subhashis Kundu, Kamma Ramakrishna Rao, Manish Kumar Gupta, Anindya Sarkar

The slag measurement systems in the cast house are very important. In the conventional method, the slag is granulated in a slag granulation system, and the slag flow rate is measured by the associated belt scale. However, in places where a slag granulation system is not available, the alternate approach is to deduce a theoretical calculation and develop the measurement because the commissioning of such slag granulation requires huge capital and has inherent geographical limitation. However, the theoretical approach suffers from several drifts and is far from the reality. In the present paper, we have innovatively engineered a sensor by designing the stellite-coated thermocouple that can measure the temperature of the slurry and placed it in such a way that the abrasive slag granules do not obstruct it, but we could measure the temperature of hot water, and further based on the thermodynamic approach, the slag flow rate is determined that can be compared with the theoretical approach. This approach of slag rate measurement is cost-effective and long-lasting.

Oct 2, 2023

By S. Lin

Fan stall is a notorious phenomenon with axial-flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts are very complicated and not well understood. Results from laboratory experiments indicated that the immediate consequence of a fan working across its stall zone (i.e., the pronounced trough on the fan characteristic curve) is that some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a non-achievable quantity range of the branch because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). These concepts are introduced based on the test results from tubing networks to bring attention to these important characteristics of ventilation systems.

Jan 1, 1996

By Hans E. Tausig

The economics of transporting minerals by sea in less than full cargo lots encompasses an analysis of production costs, sale and inventory calculations and a careful comparison of ocean freight costs all of which when pieced together will usually definitively indicate which of the ocean freight alternatives is the correct one for the economic factors involved. To illustrate: Let us assume that a production to be marketed yields 60,000 metric tons of copper concentrates over a twelve month period. Shipment is geographically viable through Vancouver, B.C. The production has been sold to a Japanese Smelter and the mine produces at a rate of 5,000 metric tons of concentrates per month. The copper has been sold CIF FO. The Seller has carefully investigated ocean freight rates Vancouver, B.C./Hibi, Japan and finds that he could obtain a twelve month freight contract at $15.00 per metric ton FIGS based on a loading/discharging speed of 4000/ 2000 metric tons per WWDSHEX (weather working day, Sundays and Holidays excluded) this freight rate being predicated on shipping in lots of minimum. 15,000 tons. A further freight investigation reveals that to ship at the same terms and conditions but in lots of 5,000 tons, and shipping each month (in accordance with the mine's actual production) would cost $20.00 per metric ton FIOS. The calculation that is now made is whether it is more desireable to pay a higher ocean freight by shipping in 5,000 ton lots or to pay the lower freight where here the ocean freight involves a difference of some $300,000.00.

Jan 1, 1979

By M. Misra, J. Nanor

The removal and stability of arsenic over a wide pH range (3.0-10.0) from synthetic solutions and industrial waste effluents (including mining waste tailing slurry) can be accomplished with addition of impure lanthanum chloride alone or in conjunction with ferric sulfate. The long term stability of these correspond­ing precipitated compounds is critical from the disposal stand­point. In this paper test results of this new process for arsenic removal and stabilization from the above mentioned systems are presented. Also, precipitated arsenic compounds (lanthanum arsenate, lanthanum-ferric arsenate, ferric-lanthanum arsenate and ferric arsenate) from synthetic solutions have been charac­terized. The characterization technique used was XRD. XRD patterns which shows that the lanthanum arsenate and lan­thanum-ferric arsenate formed in acidic and alkaline pH at room temperature are crystalline. On the contrary, ferric arsenate and ferric-lanthanum arsenate compounds formed under the same conditions as lanthanum arsenate were amorphous.

Jan 1, 1998

By Steven G. Vick

Not too long ago a mill superintendent, when asked where his tailings were being disposed, could simply shrug his shoulders and point to the open end of the thickener discharge pipe. This “out of sight, out of mind” approach to tailings disposal is a practice of the past. Today there are very few planned hardrock or energy-related mining facilities where tailings disposal has not been identified as the major area of impact and controversy. In fact, development of some ore bodies has been stymied altogether by lack of suitable sites or methods for tailings disposal. The bottom- Iine result is that tailings disposal often controls the permitting lead time and has a significant influence on construction cost (up to 2070 in some cases) of new minemill complexes. The following article, the first in a series of three, explores technical background and historical perspectives on siting and design of tailings impoundment facilities.

Jan 6, 1981

By Dominique Francois-Bongarcon

The world mining industry is facing a severe recession. Thus, it is time to recall the value of geostatistical methods which were formerly developed as a money-saving and productivity-increasing tool. The situation has worsened, but the techniques of geostatistics have dramatically changed. Up to millions of dollars can be saved during exploration with simple use of variograms; then, during reserves estimation with kriging methods; and finally, with the parameterization of reserves, when evaluating a project and optimizing its global mining parameters.

Jan 1, 1983

By K. Mohamed, G. Rashed

A conventional mechanical anchor bolt consists of a smooth bar threaded at the anchor end, with a conical wedge, and a mechanical shell anchor. When the smooth bar is torqued, the conical wedge pushes the shell anchor against the borehole wall. Coal mines use mechanical bolts in addition to other types of bolts to control the deformation and stabilize the yielded coal ribs. Limited research has been conducted to understand how a mechanical anchor performs in a coal rib. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted the study described in this paper to define the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of a mechanical rib bolt. Based on the strength of the coal seam and the conditions of the coal mines, the bolts were installed at different amounts of torque. A typical tri-linear load-deformation response was obtained from these tests. It was found that the anchorage capacity depends on the coal strength, and the anchorage stiffness depends on the installation torque. The outcome of this research provides essential data for rib support design. INTRODUCTION Rib falls are a serious hazard in underground coal mines. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Although resin bolts has been used increasingly in the last few years to control coal ribs, mechanical bolting (mainly expansion-shell bolts) is still used in many underground coal mines. Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 79% of the mines determine their rib support requirement based on the depth, mining height, and the loading conditions, of which 35% use the conventional mechanical bolts. Conventional mechanical bolts are preferable for rib support because they do not require the miners to be too close to the rib during rib bolting. Hence, using the conventional mechanical rib bolts can reduce the risk of injuries and fatalities during the installation process. The mechanical bolt or the point-anchored bolt is the oldest type of rock bolt that is still in use today. The point-anchored bolt is a tensioned bolt anchored down the hole with a mechanical expansion shell or a grouted medium (Peng and Tang, 1984). Figure 1 shows the components of the mechanical anchor bolt. The mechanical anchor bolt consists of a plug, a shell anchor, a headed smooth bar with the top end threaded, a bearing plate, a hardened washer, and sometimes a friction-reducing washer. The shell anchor can be either standard or bail type. The shell of the standard type is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the smooth bar is generally 5/8 in for the #5 bolt or 6/8 in for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the wedge down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall.

Jan 1, 2019

By Andrew C. Katen

The mining industry faces increasing geopolitical risk in the coming decades. Constraints such as resource nationalism, corruption and social license could grow to outweigh fundamental limitations like geology or supply and demand (Ernst & Young, 2013; Verrastro et al. 2010). Lurking beneath these more immediate and palpable concerns, however, may be more significant risks entrenched in geography and history. Deep-rooted cultural and strategic forces that emerge slowly ? or erupt suddenly and unexpectedly ? can generate momentous and far-reaching political, social and economic changes. While multinational enterprises routinely assess for political risk, the nature of minerals extraction means long-term and systemic geopolitical conditions are especially important for mining companies to identify and understand. Mine development is a decades-long process that binds companies to the land and makes changing course to avert emerging threats a difficult and costly option. Consequently, geopolitical assessment is a pertinent and valuable tool that mining companies can use to more comprehensively evaluate strategic threats and opportunities. Geopolitics is the study of society, politics and strategy through the lens of geography (Gray, 1996). Its emphasis on relatively permanent physical features of the earth makes geopolitics a uniquely valuable tool for assessing political risk. Topography, climate and natural resources have shaped, constrained and motivated peoples and governments throughout history. These influences transcend regimes, policies and borders ? and even states themselves ? which, by contrast, change often and dramatically. Framing politics against mountains, deserts and rivers supports identification of historical patterns and forecasts of emerging trends. In other words, the physical map provides an objective and consistent model for studying a subjective and dynamic subject such as politics (Sloan and Gray, 1999). Consequently, geopolitical assessment can highlight threats and opportunities that go unaddressed by other risk methodologies that emphasize current conditions (Glancy, 2012). Taken together, the permanence of geography, hindsight afforded by centuries of political history, and interconnectedness of world events makes geopolitical assessment a valuable approach for conceptualizing strategic risk.

Mar 1, 2014

By Sammie D. Guy

This paper discusses the subject of "Improving Contracting Methods" from the owners point of view, particularly the public. An overview is given of the work of the U.S. National Committee on Tunneling Technology and some apparent results of the implementation of these recommendations or lack thereof. Selected recommendations that are not being implemented are discussed as to the the desirability and the possible impact of their implementation. Impediments to acceptance of the recommendations are identified and solutions proposed. The difference in the flexibility, attitudes and approaches of owners, public, quasi-public and private, toward improving contracting methods are discussed. Particular emphasis is given to the fact that the onus to improve is on the owner because they usually develop the contractual language or at least have the final decision on its content and are or should be an equal party to the contract during its administration.

Jan 1, 1983

By Howard L. Hartman

To concede that I am the most surprised - not to mention the least likely - recipient of the Daniel C. Jackling Award is a true confession I must share with you. Quite honestly, I've asked myself, "Why me?" The Jackling Award has a well-deserved reputation of being a practitioner's, a doer's, a CEO's award - not kudos for a retired school teacher! While at least five of the previous recipients have taught in universities, to my knowledge I am the first to earn the award for "alleged" academic accomplishments. It is humbling enough to keep me livable for a long time. If you glance over the roster of Jackling Award lecture topics, you will spot another anomaly: The lectures last year and this deal with the subject of education - the only two in the 37-year history of the award. The two complement one another rather well, too, C. Allen Bom of Amax addressing critical needs of public education, while I am going to look at the post-high-school years. But I want to focus on more than engineering education. The training role of industry - the principal consumer of our product-also warrants examination. As I hope to establish, there is something unique about mining engineering - education and practice - that is both strength and weakness. We need to recognize that, if we are to cope with the weaknesses in order to capitalize on the strengths. We look at five premises that relate to the uniqueness of the mining engineer and his or her preparation for a professional career.

Jan 1, 1991

By R. C. Gilmore, A. Juganda, Jr. Bogin, S. Saki, S. A. Lolon, J. F. Brune, Jr. Zipf, J. W. Grubb

"Methane-air mixtures form explosive gas zones (EGZs) in underground longwall coal mine gob ventilation systems. Such EGZs have caused a number of fatal mine explosions, including the 2010 disaster at the Upper Big Branch mine, where 29 miners lost their lives. Researchers at the Colorado School of Mines use Computational Fluid Dynamics (CFD) modeling to predict EGZ locations. In this paper, a model of a bleeder-ventilated gob system includes two adjacent panels, an active longwall and a mined-out gob. Boundary conditions for the simulations match statutory ventilation conditions for methane concentrations and air flow rates at common measurement points throughout the mine. The modeling results predict the persistence of EGZs in the gob that may compromise the effectiveness of the bleeder ventilation system. INTRODUCTION Mine operators must maintain statutory air flow and air quality requirements at various locations throughout the mine ventilation network. U.S. regulations generally require mine operators to establish bleeder ventilation systems surrounding longwall gob areas (30 CFR §75.334.) Gilmore et al. (2015) documented that explosive gas zones (EGZs) exist within bleeder-ventilated gobs and may extend into the bleeder entries that must be examined weekly, presenting an immediate fire and explosion hazard to mine examiners. In a project funded by the National Institute for Occupational Safety and Health (NIOSH) under contract 200-2009-31409, researchers at Colorado School of Mines have developed a tool for modeling gob air quality using Computational Fluid Dynamics (CFD). This CFD model is capable of examining a wide range of longwall mine ventilation systems. Marts et al. (2014a, 2015) studied progressively sealed gobs with U-type ventilation and using a back return. Saki et al. (2015) examined the impact of gob ventilation boreholes and face air quantity effects on tailgate methane concentrations. Gilmore et al. (2014) modeled bleeder-ventilated gobs and Gilmore et al. (2015) studied the effects of bleeder regulator settings on EGZ volume and locations in the gob. CFD studies for progressively sealed gobs were generally carried out using 5000 ft (1500 m) panels because the gob atmosphere remains largely unchanged from about 500 m (1,500 ft) inby the face. A modular meshing methodology (Gilmore, 2015) permitted researchers to extend bleeder models to 10,000 ft (3050 m) to include the full extent of bleeder entries. This paper further expands the bleeder CFD model to study the gob atmospheres of two adjacent longwall panels, each 10,200 ft (3100 m) in length, with the active face located 6,700 ft (2040 m) from the startup room."

Jan 1, 2016

By D. J. Simbi, T. R. C. Fernandes, M. Nyamhunga

The recovery of P2O5 from a 90-95% minus 45 microns phosphate slimes sample was carried out in a 5.08-cm internal diameter and 549-cm high flotation column cell. The influence of the feed rate, feed percent (%) solids, and frother dosage on the recovery was investigated following a truncated cubic 3 level by 3 variables experimental design. Two three-variable interactions of feed rate (-l)/feed percent solids (+l)/frother dosage (-1) and feed rate (-l)/feed percent solids (-1)/ frother dosage (+I) gave the region of optimum column performance: recovery (52.60-74.50%), mass yield (15.68-18.80%), and concentrate grade (22.87-31.2196). The collector dosage also showed a significant influence on the column performance. The high reagent consumption relative to the current plant levels points to the need for the removal of ultrafine particles (<10 µm).

Jan 1, 1999

By Richard D. Doepker, Cathy A. Summers

Part 1: Physical Characteristics The physical and mineralogical characteristics of samples from five sources in the Western United States were determined using size analyses, microscopic studies, and point counts. These results were combined with leachability assays and the chemistry of leachates obtained during slurry tests to predict sample dissolution characteristics during column leaching tests. Part 2: Dissolution Characteristics Two columns of each sample were leached over a period of 3 years with synthetic rain. Residence times were between 2 and 11 weeks. The samples were subjected to daily and seasonal temperature fluctuations and wet-dry and freeze-thaw cycles. During the latter part of this study, a biocide leachant (sodium benzoate) was substituted for synthetic rain to assess the degree of dissolution caused by biological oxidation. It was found that the presence or absence of barite or carbonate minerals can be used to predict the leaching behavior of the column material.

Jan 1, 1995

By Y. Luo

Surface subsidence monitoring is the most effective means for investigating the nature of, and developing the techniques for predicting, the surface movement and deformation process. However, because of imperfection in survey equipment and field practices, the surface movement data collected from field survey are not error-free. Also due to lack of proper numerical techniques for computing surface deformation from the measured surface movement data, a relatively large portion of the subsidence data collected could not provide more information other than surface movement. In this paper, the sources and magnitude of errors in the measured surface movements and calculated surface deformation are discussed. Techniques for improving the accuracy of the calculated deformation indices (i.e., slope, strain, and curvature) are developed. The proposed techniques include: (1) proper selection of monument spacing for subsidence monitoring; (2) a data smoothing technique for data pre-processing; and (3) a number of numerical methods and/or procedures for calculating surface deformation indices from the measured surface movement data.

Jan 1, 1992

By Ryan C. Stephan, Zach Agioutantis, Christopher Mark

Over the past 15 years, roof fall rates have decreased by two-thirds in U.S. coal mines and by even more in regions where the roof is weakest. This remarkable reduction in the number of roof falls has been accomplished with more effective roof support systems. The purpose of this paper is to present an empirical design methodology that uses real-world data to quantify the basic roof-support concepts that have been successful in the United States. A new computer package, called Analysis of Mine Roof Support (AMRS), implements the design methodology.

By Robert J. Neubauer

I was asked here today to discuss the first long-term freight rate contract ever signed by a U.S. railroad and shipper. That was ICG&apos;s contract with the hoosier energy company to haul coal from southern Illinois to an Indiana power plant. I?ll also talk about why you can expect to see more such contracts in the future But first, let me tell you a little bit about the Illinois central gulf railroad and why coal contracts are so important to us. ICG is a principal mid-American freight carrier. We are one of the ten largest railroads in the united states and one of the ten largest coal-hauling railroads. ICG links the industrial great lakes region with the warm weather ports of the gulf coast. Some of the major points on our route map are Chicago; Indianapolis; Omaha; Kansas City; Memphis; St. Louis; and, of course, baton rouge and new Orleans.

Jan 1, 1981