Search Documents

By Bhaskar B. Thapa, Christopher Laughton, Michael P. Bruen

At Fermilab, located in Batavia, Illinois, a 4,000-foot underground complex of tunnels and caverns is being excavated on a decline of six percent, at depths of up to350 ft, below grade. The site geology consists of dolomitic and shale formations overlain by glacial till. Since the start of construction in March 2000, work to date has concentrated on the excavation and support of the Target Hall cavern, which is characterized by a low rock cover and a final lining of shotcrete. Ground vibrations, noise levels, and rock movement were monitored during excavation by drill and blast methods to prevent damage to experimental facilities, impacts on surrounding communities, and to allow evaluation of cavern performance. The cavern design was based on a UDEC numerical analysis that was validated during construction by comparison to encountered conditions and measured cavern movements.

Jan 1, 2001

By Galyn Rippentropp, Finn Erik Overlie

INTRODUCTION The wet shotcreting system utilizing steelfiber microsilica shotcrete with remote controlled equipment (The Robocon System) was developed in Norway 7-8 years ago. Norway was the natural origin for this system due to several factors. Almost 30% of all underground hydro-power stations in the world are located here. These projects created a need for high productivity shotcreting rigs for the rock support work in the caverns and in the connecting tunnels. During the period of 1976-1980, more than 1000 miles of tunnels were completed in Norway. Secondly, the utilization of microsilica in concrete was also developed in Norway due to a concentration of the world's ferroalloy p ants there. Robocon has presently placed approximately 110,000 m (150,000 cu. yds.) of this superior shotcrete, and has consequently an extensive experience in the shotcreting method. During a relatively short period of time (1975-1980), Robocon had a change from hand-operated, dry-process shotcrete to remote-controlled, wet-process shotcreting, because of improved productivity, reduced rebound, safer and cleaner working conditions. The introduction of microsilica and water-reducing admixture made it possible to produce wet-process shotcrete of high strength.

Jan 1, 1987

By H. Hejny

"The mine of the future will exploit mineral raw materials at greater depths than today, requiring completely different approaches compared to today’s deep mines, in order to get mineral rights. Only these eco-efficient mines will contribute to improved access to domestic mineral resources, secure the sustainable supply of mineral raw materials for Europe and reduce the import dependency. IntelliMine will contribute to realise these concepts of invisible, zero-impact and safe mines. The mine of tomorrow will run an integrated concept in order to guarantee the desired level of sustainability. All operations necessary for the eco-efficient provision of the minerals including waste management will be carried out underground. This will drastically reduce the volumes being transported, minimising above ground installations and thus the environmental impact. IntelliMine will develop necessary innovative methods, technologies, machines and equipment for the safe, eco-innovative, intelligent and economic exploitation of mineral raw materials in the EU, especially at greater depths."

Jan 1, 2011

By Tom Gonzales

At San Manuel, AZ, Magma Metals Co. operates an Outokumpu flash furnace, four Peirce-Smith converters and two anode casting wheels that are supported by six anode vessels. Process gasses from the flash furnace and converters are treated in a two-train/ double-contact sulfuric acid plant. The plant captures 98% of the sulfur. A new flash furnace was commissioned in July 1988. It has since processed more than 2.7 Mt (3 million st) of sulfide concentrate without a major rebuild. The company has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. Process flow description At Magma's San Manuel plant, concentrates and other copper-bearing material are blended and conveyed from two separate areas of the plant to three 420 t (465 st) capacity wet charge bins located above the rotary dryer. Flash furnace silica flux is conveyed to a 227-t (250-st) capacity fine flux bin located adjacent to the wet charge bins. The concentrate and flux are blended in controlled amounts and fed into a 168-t/ h (185-stph) gas-fired rotary dryer. The wet charge enters the dryer at 8% moisture and is dried to 0.2% moisture. The dried charge is pneumatically conveyed to a 580-t/h (640-stph) dry charge bin located above the flash furnace. Flash furnace charge is drawn from the bin by two drag conveyors at a concentrate feed rate of 145 t/h (160 stph). The charge is mixed with enriched combustion air and injected into the furnace reaction shaft. In the reaction shaft, the charge is oxidized to form matte, slag and a rich SO, off-gas.

Jan 1, 1992

By Donald Hulse

"Mining has been a source of controversy for at least 500 years. “Since there has always been the greatest disagreement amongst men concerning metals and mining, some praising, others utterly condemning them…” (Agricola, 1556). In 2016, it is widely recognized that mineral resources and reserves must give due regard to the social license in order to operate.“Most commonly, the social license to operate (SLO) is understood to refer to ‘the ongoing acceptance and approval of a [project] by local community members and other stakeholders that can affect its profitability’ (Moffat, 2014).” “Social License to Operate has gained traction, in part, because it is also a concept which – while remaining poorly, technically defined – is generally easily and widely understood by community stakeholders (Bice, 2014).”A generation ago we learned that mining is based on a stable platform supported by three pillars, geology, mining and metallurgy. The three-legged stool is a very stable structure (Fig. 1).In 2016, it seems that we have added some other legs to the stool (Fig 2). The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC Code) addresses “social, and governmental factors…” (JORC 2012), and refers specifically to social license in Section 4 of the Report Template “Estimation and Reporting of Ore Reserves.”The Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Guidelines refer to “environmental, legal and social data…(CIM 2003).”Compared to these, the 2014 SME Guide is positively verbose stating “a discussion of any potential social or community related requirements and plans for the project and the status of any negotiations or agreements with local communities,” (SME 2014) although in all cases the scope of this disclosure is left at the discretion of the competent person.When there are more than three legs on the stool, it is imperative that all legs be constructed exactly to the design. Any one or more legs that are out of alignment will cause the stool to wobble.Engineers are trained to create designs to meet specifications. Loads can be estimated, forces calculated and cost studies completed that will lead to, not only a stable design, but the most efficient design that meets the specifications."

Jan 1, 2015

By Daniel W. H. Su

A nearly 305-m- (1,000-ft-) wide sandstone channel was projected to run through the mid panel area of a 457-m- (1,500-ft-) wide longwall panel in a southwestern Pennsylvania coal mine. This sandstone channel was known to cause serious longwallface roof control problems in the mine?s B-panel area in 1998 and 1999; and most recently, it induced many large face cavities and caused a substantial production delay in the preceding panel. For the two B panels mined in 1998 and 1999, hydraulic fracturing of the massive sandstone was conducted to facilitate better caving, thus relieving cantilever compressive stress at the longwall face. Vastly improved longwall face condition was observed and four weeks of mining delay due to bad roof conditions were eliminated. The implementation of the hydraulic fracturing technique, results of underground observation and measurement, and results of numerical modeling were summarized in a paper presented in the 20th International Conference on Ground Control (Su et al., 2001). This article is a summary of the activities that took place during a four-month period (October 2011 through February 2012) at a Consol Energy longwall mine southwestern Pennsylvania to improve face conditions and safety of underground personnel during mining of the 457-m- (1,500-ft-) wide longwall panel. The elevated concern for safety was driven by adverse face conditions encountered while mining the preceding longwall panel. Many of the problems were attributed to a thick and massive sandstone channel. A joint task force consisting of coal operations engineering, Pennsylvania operations engineering and CNX Gas personnel was formed in August 2011, which recommended drilling four hydraulic fracturing holes along the center axis of the sandstone channel to reduce pressure and improve face conditions at the longwall face. To further provide detailed monitoring of the longwall face and to evaluate the effectiveness of the hydraulic fracturing program, the Longwall Visual Analysis (LVA) software (Hoyer, 2011) was installed in early December 2011 to track the face pressure and c

Jun 1, 2013

By Nathan Bowersox, Zuzana Skovajsova, David M. Jurich, Brian Harris

When unwatered after more than 50 years of operation, the White Rock Tunnel of the Upper American River Project in the foothills of the Sierra Mountains exhibited failing rockbolts and ground falls. Repairs designed for the 5 mile-long, 24-foot horseshoe unlined hydropower tunnel included pattern rock bolts, shotcrete, and cleanout of the rock trap. The work, originally scheduled for two 3-month winter outages, was completed under challenging conditions in a single 4-month outage following a carefully sequenced work plan using robotic shotcrete and rockbolter machines. Flexibility, creative solutions, and collaboration by all parties were key to project success.

Jun 13, 2021

By D. Kozelj

Introduction The porphyry copper deposit “Borska Reka” is the biggest undeveloped deposit in the Timok Magmatic Complex (TMC). Total reserve calculated manually is 611 Mt (cut-off grade 0.3% Cu) of 0.62% Cu, 0.21 g/t Au and 1.81 g/t Ag and 869 Mt of 0.58% Cu, 0.14 g/t Au and 1.11 g/t Ag using software. But since several deep drill holes are suspended in high grade (0.7% Cu) porphyry, total reserves could exceed 1Gt. The massive sulfide is also detected in the central (12 m at 4% Cu) and the bottom of porphyry style. Deposit was discovered during geologic exploration of deeper part of the Bor copper and gold deposit, i.e. area of high sulfidation with dominant massive sulfides. During exploitation of massive sulfide, constant explorations were carried out aimed at the expansion of reserve and discovery of new ore bodies. In that way, porphyry copper mineralization was discovered without knowing in the beginning that it was different mineralization type in regard to the ones that had been already identified and exploited. Vertical extension of porphyry is 0 m up to -1000 m sea level and not contoured along plunge. In the very beginning (1976), the exploration was focused on the shallow part of porphyry. That is because block caving method of massive underground mining was not developed at that time. Up to 1999, most of activity was related to underground exploration up to level -395 m. Geographic position The Bor deposit is located close to the industrial and University town Bor, which has over 50,000 inhabitants (census made in the year 2002). Apart from the Bor Mines, industrial complex of Mining & Smelting Basin Bor (RTB) comprises also a copper smelter (installed capacity up to 160,000 tons of blister copper) and tank house, copper wire factory, copper tube factory etc. Currently, RTB Bor is under privatization process that is going to be completed by the end of 2006. Up to date, over 20 companies have bought tender documentation.

Jan 1, 2007

By Heiner J. Sander

Stanford University operates the National Research Facility which is located at the Stanford Linear Accelerator Center (SLAC) in Menlo Park, California. In order to improve and allow for enhanced experiments, the current facilities required expansion. A1500 foot long tunnel (20 ft wide by 21 ft high) and a 220 foot long underground cavern (49 ft wide by 32 ft high) were excavated through the Ladera Sandstone formation which is an intermediate geo-material with week rock properties. The overburden between surface and crown of the structures varies from 10 to 80 feet. The underground structures were excavated according to the principles of the NATM (New Austrian Tunnel Method). This paper addresses the challenges that were encountered during the construction phase of the project and how construction issues were resolved mutually by the owner, engineer and contractor. The implementation of geotechnical instrumentation, recorded data and interpretations, soil conditions and behavior encountered during construction are also presented.

Jan 1, 2008

By Kevin Beirne

Most people involved in the mining industry are familiar with student-industry co-op work-study programs. Many colleges and universities have used them for years. Northern College’s Haileybury School of Mines student co-op program adds a new dimension of productivity to the college and the mining industry. The college is located in Hailey-bury, Ontario, Canada. An example of the program’s success is the school’s relationship with Sabin Metal’s SMC (Canada) Ltd.’s McAlpine Mill in Cobalt, Ontario. Students gain practical knowledge and experience while industry gains an eager-to-learn worker. And many of the college’s advanced research services are made available to industry to supplement their own capabilities. The McAlpine Mill was established to provide custom milling of slags and ores. It also recovers metal values from other products of the primary and secondary precious metal industries.

Jan 1, 1999

By Dr. Peter J. Conroy

The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to the DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. This paper summarizes the work that has been completed through September of 1981 and presents the results that have been achieved during this period. Technical difficulties encountered during both the installation and monitoring phases are discussed, and recommendations for future work are presented.

Jan 1, 1982

By A. Halim, J. Gustafsson, A. van Wageningen, J. Johansson, · J. Lööw, K. Kocsis

A major part of the European Union’s (EU) project Sustainable Intelligent Mining System (SIMS) is investigating the development of diesel-free/carbon–neutral underground mines in order to ensure sustainable underground mining in the future. Replacing diesel machines with electric vehicles in underground hard rock mines has been widely acknowledged by the mining industry worldwide as a critical step to improve working conditions by reducing diesel exhaust–related contaminants, to reduce mine ventilation electrical power cost by reducing mine airflow quantity, and to reduce mine greenhouse gas emissions. All of these are major requirements to achieve sustainable future underground mining practices. A field trial of Epiroc’s 2nd generation of Battery Electric Vehicles (BEVs) at Agnico Eagle Finland’s Kittilä mine was conducted during 2019–2020. Vehicles tested were MT42 mine truck, ST14 Load-Haul-Dump (LHD), and Boomer E2 jumbo drill rig. This paper outlines the improvement of the working conditions observed in the field trial, and the opinions of the mine personnel at Kittilä mine on using BEVs instead of diesel machines. Measurements of atmospheric contaminants and air temperatures taken during the field trial clearly demonstrated a significant improvement of working conditions when BEVs were operating as opposed to diesel machines. This field observation was supported by the opinion of the majority of the Kittilä mine workers. However, some remaining concerns must be addressed before BEVs can replace diesel machines.

Oct 25, 2021

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

In recent years, there has been increasing interest in the role that individual factors play in health and safety (H&S) outcomes in the mining industry. Two surveys, one measuring self-reported routine safety performance and one measuring individual perceived competence in the non-routine knowledge, skills, and abilities (KSAs) critical to emergency response, were administered to two samples of mineworkers in separate research studies over a 2-year period (N=2,020 and 696, respectively). Eight demographic items were common to both surveys and their associations with each performance outcome were tested in response to a series of exploratory research questions.

Jan 9, 2022

By B. Waterman, D. Ramey, L. Schlink

"Water is a primary commodity for most industrial processes. It has become a global focus in light of climate change and population growth. Reuse of process water has two major benefits - minimize the amount of fresh water added now and minimize the amount of discharge water that requires treatment later.Mining and mine product processing has its share of reused water. For example, reclaim water from a tailings impoundment, overflow from thickeners and leach solution to raffinate and back again all demonstrate the use and reuse of water in mining circuits. Eventually, a mine reduces production or ceases operations completely, eliminating the option to reuse the impacted water and, thus, requires treatment of the remaining water.Current methods of water treatment remove the impacts, providing clean water for discharge, but leaves behind a concentrated waste that requires further treatment or disposal of a hazardous waste. Freeport- McMoRan is currently testing three water treatment technologies specific for sulfate and/or metal removal from mine impacted water with the approach of transformation not concentration. These technologies provide clean water for alternative use while creating byproducts that could be marketable, or disposed as a nonhazardous material, thereby reducing the cost and longterm liability of disposal.The selection of a water treatment process is site-specific. The volume of water, contaminant to be removed, disposal options, length of time for treatment, location of plant and reagents and discharge requirements are some of the factors that need to be considered when selecting a water treatment process. Common water treatment technologies for mine impacted water consist of low- or high-density sludge (LDS/ HDS), reverse osmosis (RO) and evaporative technologies. In addition to operating costs, these processes require additional handling of the concentrated sludge or brine. Advanced water treatment technologies include ion exchange, solvent extraction and metals precipitation with or without the aid of a biological system. Some of the more complex systems have a series of unit operations to achieve required discharge regulations."

Jan 1, 2014

By Ren Xiangwen, Shi Xuefa, Shao Mingjuan, Ye Jun, Yang Yaomin, Li Bing

"The Mid-Atlantic Ridge (MAR), one of the archetypes of slow spreading ocean ridges, extends from the Arctic Mid-Ocean Ridge southward to the Bouvet triple junction making up a significant proportion (~ 40%) of the global oceanic ridge system. During the past few decades, many hydrothermal fields like TAG, Logatchev, Ashasze were discovered along the northern part of the MAR, whereas the southern part, which makes up one third of the ridge (6000km), shows little documentation of hydrothermal mineralization, except for three sites: Site 4°48! the Nibelungen Field, and Lilliput. During March to May 2011, following discovery of three new hydrothermal fields during the 2nd Leg of COMRA's 22 Cruise of the R/V DayangYihao, the 3rd and 4th Legs found another two high temperature hydrothermal fields (SMAR15°S, SMAR26°S), one low temperature field, and several fields with strong turbidity and temperature anomalies in the water column. In this study, we present a preliminarily study of the mineralogy and isotopic geochemistry of the sulfides from SMAR 15°S and SMAR26°S.SMAR 15°S is situated in a SE-NW offset depression of an axial neovolcanic ridge in the median valley, with water depth of about 2793m. In the water column around this field, strong turbidity and temperature anomalies were detected. Ten-meter tall venting chimneys, hydrothermal mounds, as well as a large amount of hydrothermal vent shrimp were also observed and recorded by ROV and deep-tow camera surveys. The samples collected from this field include sulfide chimney fragments, massive sulfides and basaltic rocks. Based on the major metal and the mineral assemblages, three types of sulfides have been identified: 1) Zn-Fe rich sulfides with abundant wurtzite and pyrite zoned fragments, 2) Cu-Fe rich sulfides with much isocubanite and pyrite assemblage, 3) Fe-rich sulfide with massive pyrite fragments. These indicate that this field has undergone at least three phases of mineralization during the venting history."

Sep 1, 2014

Flooded-bed scrubbers on continuous miners have been shown to be an effective respirable dust control technology, traditionally used during the extraction of extended cuts of up to 12.2 m (40 ft). To effectively use scrubbers in faces that employ exhaust ventilation, the return ventilation curtain or tubing should be located outby the scrubber discharge on the continuous miner, which results in a setback distance from the face of approximately 12.2 m (40 ft). The goal of this research was to compare respirable dust levels generated in 6.1 m (20 ft) cuts when using extended curtain setbacks with a scrubber operating to dust levels in 6.1 m (20 ft) cuts when using traditional exhaust face ventilation without a scrubber operating. Dust surveys were completed at three mines with area and personal sampling conducted to quantify respirable dust concentrations on a cut-by-cut basis. Sampling results did not show a statistically significant difference in respirable dust at the continuous miner or shuttle car locations with and without the scrubber operating. However, with the scrubber operating, respirable dust concentrations in the return airstream downwind of the miner showed reductions of 91%, 86%, and 40% at Mines A, B, and C, respectively. The reductions at Mines A and B were statistically significant. Likewise, reductions in respirable quartz dust levels in the miner return were observed at all three mines, with statistically significant reductions of over 80% observed at Mines A and B. Consequently, operation of the flooded-bed scrubber did not impact respirable dust levels in the face area but did significantly reduce respirable and quartz dust levels downwind of the continuous miner. These results were obtained with the mines operating at or above the minimum operating levels specified in their ventilation plans.

Feb 23, 2014

By I. S. Parrish

This article offers one of the infrequent looks at Chinese mining. It includes a brief review by Parrish of a tungsten symposium held there and his comments on and impressions of the mines he visited. In early Oct. 1981, a Symposium on the Geology of Tungsten was held in the Peoples Republic of China. There were approximately 100 participants. Half of them were Chinese. The remainder included representatives of the United Nations, geologists from other nations in Southeast Asia, and 10 invited specialists from other countries. The invited guests included K.F.G. Hosking of the Camborne School of Mines, United Kingdom; C.S. Hutchinson of the University of Malaysia; K. Mattson of LKAB Int. AB, Sweden; T. Kwak of Latrobe University, Australia; K. Sato and S. Ishihara of the Geological Survey of Japan; M. Clarke of the Department of Mineral Resources, Indonesia; P. Bateman of the US Geological Survey; and the author. R. Horsnail of Amax was also invited but was unable to attend because of delayed visa clearance. The meeting was noteworthy because the Chinese were presenting more than half the papers. In addition, following the formal session, everyone was taken to the famed Jiangxi tungsten district and toured four mines there. Organization and Background The idea for a symposium on tungsten geology was brought up in late 1979 during a visit to China by the Economic and Social Commission for Asia and the Pacific (ESCAP) and, in particular, by members of the Regional Mineral Resources Development Centre (RMRDC) of the United Nations. Discussions continued and in the spring of 1981 invitations were sent to selected geologists throughout the world. China's Ministry of Geology handled arrangements, scheduling, and logistics. Travel to China and all correspondence before the symposium were coordinated by the Bandung, Indonesia Bureau of RMRDC. All costs in China were met by the Peoples Republic of China. Airfares and "per diem" enroute for participants were paid by respective governments, sponsors, or individuals. On Oct. 10, visiting participants entered China from Hong Kong. The author and a few others traveled by train to Guangzhou (Canton). Most of the group flew in the next day. The entire group was then taken to Nanchang, traveling by sleeper train and arriving on Oct. 11. The symposium group stayed at the Kiangsi Hotel, where the meetings were held. Meetings Oct. 11 was a day of orientation and rest. The group was taken to an art museum and treated to a Chinese opera movie. The formal meetings began on Monday, Oct. 12. Simultaneous translations aided presentations, though more than half the Chinese speakers delivered their talks in English. The acoustics and sound system were excellent, and the Chinese provided 35-mm and overhead projectors. There was no screen, however, and the yellow, painted wall that was used detracted from projection clarity. In general, the Chinese papers were detailed, thoughtful, and professional. Some, naturally, were stronger than others. Taking them as a unit, one derives the following sequence to the Chinese approach to tungsten exploration: (1) Geologic investigations with mapping at a scale of 1:200,000 accompanied by only minor geochemical or geophysical work. (2) Geophysical investigation with regional gravity and magnetic surveys directed toward identifying deep, tectonic systems and seeking granites in thick, crustal environments. (3) Geochemical sampling in-

Jan 6, 1982

By James Wm. White

Today a large number of open pit mines use computer-based mine management systems to automatically assign haul trucks, track equipment, and manage information. Now advances in digital communications allow the use of these systems in underground operations. Underground mine management systems help maximize production by providing impressive gains in areas such as equipment and manpower utilization, draw point equalization in block caving operations, preventive maintenance, and safety. Current systems use allocated or "locked" train and LHD dispatching. While allocated dis-patching rarely optimizes open pit production, it offers an efficient mode of operation underground where options are more limited.

Jan 1, 1996

By A. Vien

Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the results of a research program to evaluate the technical and economical merits of such a device on a SAG mill. The evaluation includes validation through discrete element modelling and comparison to measured static volumetric load. Inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed.

Jan 1, 2001

By I. J. Wu

China’s land area, comparable in size to United States or Canada, contains diverse geological environments and mineral resource potential. The diversity in geological environments is such that the potential for developing many world-class mineral deposits in China is good. However, China’s mining sector was not open to foreign investment until the1990s. The long-term prospect for Chinese resource development is attractive because of China’s enormous population and cumulative demand for minerals. Approximately 33 foreign mineral companies, including 11 major internationals, are to various degrees active in China. Chinese mining laws and regulations pertaining to joint ventures with foreign companies are, from the international investment prospective, evolving slowly, but positively. This positive trend is continuing under the current government reform process, which is moving China towards a freer market economy. Although improving the enforcement of relevant laws and regulations is an ongoing process, the environment for mineral investment and joint ventures is increasingly more accommodating to foreign companies.

Jan 1, 2000