Search Documents

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By K. Zabrusky

Epithermal vein systems are often modeled as simple, discrete high grade structures within low grade host rock. However, geologic setting and structural preparation influence how such vein systems form. In structurally complex areas, veins may follow several structural trends and occur on a variety of scales. Geologic and grade modeling within such complex structural regimes can be difficult as individual veins cannot be delineated from host rock based on grade alone. Structurally complex areas require a different approach than traditional discrete vein modeling. Presented herein is a study of a structurally complex area that hosts vein mineralization to be mined underground. All veins could not be modeled discretely, so an alternate approach was needed. Major structures were modeled using surface and underground mapping and were then used to create a structural trend for the area. This trend was used to guide 3D grade shell construction. The grade shells replaced 3D vein solids for grade estimation in order to mitigate the influence of high grade samples. Structurally guided grade shell construction offers a more effective modeling method than discrete vein modeling in deposits that are structurally complex.

Feb 23, 2014

By Al. Valero, A. Domínguez

This paper appraises the energy requirements for mineral production through an exergy approach taking into account the long-term decline in ore grades. In this context, the exergy required for restoring resources from the dispersed state of the so called Crepuscular Earth into the physical and chemical conditions in which it was delivered by the ecosystems in light of the available technology, is known as exergy cost. The exergy cost is the point of reference in order to evaluate in a single variable, characteristics such as composition, concentration (ore grade) and the state of technology. The ratio between the exergy cost and the minimum thermodynamic cost required to accomplish the same process is called unit exergy cost and provides a measure of the irreversibility of the analyzed processes. Otherwise, the ore grade is one of the main issues which affects directly the costs associated with mining the ore. Hence, the unit exergy costs to produce minerals from progressively lower ores grades by the current technology is analyzed. The unit exergy cost curves are presented for some important minerals such as aluminium, chromium, cobalt, copper, gold, lead, manganese, nickel and zinc, in order to know the trend when the ore grade decreases.

Jan 1, 2011

By Madan M. Singh

Although roof bolting has been a major means of strata support for nearly two decades, little attention has been directed towards the design of bolt Installations. The variables involved are interdependent and their study complex. However, some simple tests may be employed to serve as guides to the efficient design of roof bolt systems. Local conditions are continually varying and are important to pattern design. This paper discusses such considerations and suggests techniques which may be employed to effect improved roof control with bolts.

Jan 1, 1967

By Paul R. Kruesi

A patent-applied-for process has been developed in which zinc chloride is extracted by tributyl phosphate in kerosine, and stripped with ethylene glycol or ammoniated ethylene glycol. The anhydrous zinc chloride is precipitated from the glycol as the ammine and zinc chloride is prepared by thermal decomposition with recycle of ammonia. The process permits the production of high grade zinc from scraps and drosses. Its applicability to the recycling of zinc will be illustrated.

Jan 1, 1984

By Liliana Rybarska-Rusinek, Aleksandr M. Linkov, Ewa Rejwer-Kosińska

Joined modeling of stressed state and induced seismicity is a means to join geomechanics with seismic observations. When applied to quantifying rockburst hazard, it provides, on one hand, estimations in terms of mechanics, such as stress concentration, and, on the other hand, in statistical terms of the risk analysis developed in mining seismology. The modeling became possible due to progress in computers and numerical methods. However, despite tremendous increase of computational abilities, the joined modeling is still quite time expensive. To make it available for wide use and real time simulations, there is need to reduce the time cost of its key stages: calculation of stresses, caused by mining, and simulation of seismic events, induced by these stresses. The present work aims to decrease the time cost. The stages are time costly because of the same reason, which is a very large number N (up to millions) of elements, representing rock structure, openings and flaws. This leads to immense computational complexity (roughly of order N2) of conventional accounting for pairwise interactions between the elements. The complexity may be notably reduced, when employing the fact that interactions decrease with growing distance between elements. Specifically, the fast multipole methods (FMM) avoid the complexity N2, by employing translations of far-fields from whole collections of sources. This reduces the complexity to the order 22, where p is the number of terms involved in a single translation, is the number of translations, and is the dimension of the quantity translated. Still, for conventional FMM, the complexity remains too high to routinely perform joined modeling of stresses and seismicity.

Apr 26, 2022

By Marcos Vieira, Gil Vilela, Wanderson Silvério, Livia Faustino, Pierre Fernandes

New global industry standards and regulatory changes regarding mining tailings management are driving installation of tailings filtration plants to decommission existing tailings dams and implement dry stacking. Target of this project was to reduce ultrafine slime tailings deposition. Previous investigation at Samarco concentrator has showed a 35% decrease in tailings filtration throughput when feeding a mix of 95% flotation tailings with 5% slime tailings (compared with 100% flotation tailings), also worsening geotechnical aspects such as material workability during dry staking. Industrial trials using a proper filter aid at tailings filtration plant feeding a mix of 94% flotation tailing and 6% slime tailing (equivalent to 30% of total slime generation) have provided filtration performance maintenance (throughput and cake moisture), and dry stacking the dewatered material. Results achieved will enable life expansion of existing slime disposal structures, as well as potential life of mining extension. Furthermore, reagent chemistry influence is discussed by the light of geotechnical aspects, which has been showing improved KPIs, such as workability, compressibility and permeability.

Feb 1, 2025

By Mohamed Gamal, Bill Zietlow

"In oil fields that have been depleted with conventional surface oil wells but still contain significant reserves, an extraction alternative that has been constructed recently consists of a drilling gallery below the oil-bearing formation at the bottom of a 1,200-ft deep shaft where upward sloping wells are being drilled to allow oil collection by gravity. The gallery is 92-ft diameter with a flat ceiling supported by rock bolts and shotcrete structurally connected to the shaft liner, which doubles as a large tension support element. A special excavation sequence was implemented for the gallery to maximize arching in the stress above the large diameter gallery. The gallery was located in competent sandstone, constructed with sequential excavation methods, and designed with a 3D finite element model. Special consideration was given to optimizing the gallery location to take advantage of the geology for construction and support while giving good positioning to the well drilling equipment. BACKGROUND Brierley Associates was contracted to provide both design and construction management services for an approximately 1,165-ft deep, 18-ft excavated diameter vertical shaft that opens to a 92-ft diameter flat roof gallery. The geotechnical data for the site was based on information available from literature and from data obtained during core drilling and from in-situ testing in a 1250-ft deep borehole. Wire line coring was conducted using a HQ, 10-ft long core barrel with a mud-rotary drilling method through sedimentary bedrock. The geometry of the shaft and the bottom gallery is shown in Figure 1(a). GEOLOGIC SETTING AND STRUCTURAL GEOLOGY The stratigraphy at the site includes a series of interbedded marine limestone, shale, claystone, siltstone, sandstone, and chert units. Limestone and shale are the predominant lithologies in the upper approximately 675 ft, while the lower portion contains five distinct sandstone units and more abundant shale, claystone, siltstone, and coal than the upper zone. A cherty sandstone at a depth of 1,130 below ground surface (bgs) was encountered. At a depth of about 1,000 ft to 1,116 ft bgs, a non-marine sandstone unit was encountered. This sandstone is the hydrocarbon bearing layer. Joints and fractures observed in the limestone had dips ranging from 0 to 90 deg. from horizontal with joint and fracture surfaces that ranged from planar to irregular and smooth to rough. Several, near vertical shear planes with slickensides were observed with surfaces that were generally smooth and planar. RQD values for the limestone ranged from 0 to 100 percent but in general were good to excellent."

Jan 1, 2016

By M. Solomon

Crushers are designed and manufactured to survive the severe duty of mining environments worldwide. Under these conditions the crusher performance and availability is one of the critical factors in the mine?s production and profitability. Traditionally the development of these machines tends to be experience-based, incremental improvements in design due to challenges of different applications, duty, or manufacturing. In order to better serve the mining industry a new approach was taken to the design of primary crushers. This approach was to focus on safety and maintenance activities. The result of this effort is a new generation of gyratory crushers that can be serviced from above. Using the features of this new generation of crushers to their fullest extent crushing installations have improved safety, reduced design and construction costs, and lowered maintenance requirements. This presentation explores the benefits of two crusher installations utilizing top service crushers.

Jan 1, 2010

By Jeff Easton, J Johnson, D. Foot

The Mina Santa Rosa mine in Panama was the victim of a mine closure 24 years ago that left the community in dire straits. The mine showed the potential resources of greater than 1M ounces of gold and 4.5M ounces of silver. Veragold Mining Company decided to reopen the mine and address all the issues that were involved in the startup of an historic mine. This paper provides methods to restore the community trust, provide a transparent process, and develop an environmentally sound flowsheet. Immense scrutiny surrounded the Tailings Storage Facility, and the company developed a plan focused on paste thickening and surface stacking to eliminate the need for a conventional tailings’ facility. Paste thickener principles and benefits are also provided.

Feb 1, 2024

By T. Hayashi

A sophisticated process of extracting ultrafine sulfide mineral particles of under 1µm size suspended in clay slurry has been developed through studies of electrochemical properties of particle surface. Experimental procedure and data of the process applied to some clay ores containing sphalerite and pyrite, and molybdenite and other sulfide minerals are reported. Discussions concentrated on the function of process reagents, particularly on various modifying reagents, and on the effect of dispersed or flocculated state of ultrafine particles in slurry which affect significantly the performance of the process.

Jan 1, 1982

By I. Iwasaki

Precious metals are commonly believed to be recovered along with sulfide minerals in flotation, but a few neutron activation analyses showed that the recoveries of gold and silver were unexpectedly low. Recoveries of platinum group metals remained unresolved due to interferences in the analyses. Electron micro-probe, scanning electron microscope and scanning auger microprobe analyses have identified nickel arsenide minerals in the ore and confirmed a close association of platinum group metals with the arsenide minerals as minute inclusions. These results indicated a need for re-evaluation of flotation procedures which have so far ignored special problems related to arsenide minerals. The electrochemical and flotation behaviors of nickel arsenide and their implications to the flotation recovery of arsenide minerals from copper-nickel bearing Duluth gabbro are presented.

Jan 1, 1985

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Joseph Sopko, Xavier Lacourse-Dontigny

For the REM (Réseau Express Métropolitain) project, a 2500 m tunnel was built using a tunnel boring machine (TBM) under the Montreal Pierre Elliott Trudeau Airport (ADM). Although the geology under the Montreal Airport (ADM) would have been suitable for an excavation with a hard rock machine, the rst section reuired an earth pressure balance (EPB) TBM due to the soft soil located under wetlands. After excavating 280 m, the TBM was blocked in a transition zone of unconsolidated, water-bearing soils directly above the underlying bedrock. A free air intervention was not possible due to these geological conditions. After several failed attempts to create a slurry cake for hyperbaric interventions, a ground freezing system was designed and implemented, incorporating angled pipes drilled from outside the wetlands to directly in front of the cutterhead. This paper discusses the engineering reuired to form a frozen, water-tight zone in front of the cutterhead using liuid nitrogen. It also describes the complex method of replacing the disc cutters while holding the ground freezing system active in a manner protecting the health and safety of the workers.

Jun 23, 2024

By Y. C. Guan

The leaching kinetics of chalcopyrite in ammonium iodide solutions with iodine has been studied using rotating disc. The variables studied J include the concentrations of lixiviants, rotation speed, pH of the solution, reaction temperature, and reaction product layer. The leaching rate was found to be independent with the disc rotating speed. The apparent activation energy was measured to be about 50 kJ/mole from 15°C to 35°C, and 30.3 kJ/mole from 35°C to 60°C. Experimental findings were described by a kinetic model, and the overall rate was found to be: (formula)

Jan 1, 1997

By Andrew N. Peterson

US mine operators frequently fail to investigate more cost effective and productive bulk material handling systems because surface mines seem to lend themselves to truck ore haulage. In this country, as a result, use of conveyors to move heavy loads from mine to process facilities has been minimized, if not actually neglected. In contrast, there are more than 50 conveyorized surface mines in successful operation around the world. These mine operators have learned that properly applied conveyorized systems can offer major savings in capital and operating costs, which contribute to improved profits when combined with other proven mining technologies. Growing acceptance and application of conveyorized bulk material handling in surface mines also points up how unique each mine is and how careful planning contributes to maximum mine effectiveness. Because of these differences, mining executives and technical and operating staffs need to develop an understanding of three factors in applying conveyorized bulk material handling in surface mines: • Why each mine will benefit from the type of automation permitted by conveyorized operation, •What kind of equipment is available, and • What applications most effectively demonstrate the first two factors in action - hauling either ore or waste. The conveyorized systems considered in this presentation have production rates from 0.5-2.7 kt/h (500-3,000 stph). Worldwide, these systems have been operating since the early 1960s. Advantages of Conveyors Why do you want conveyorized bulk material handling? First, it almost always provides lower operating and maintenance costs. Second, it frequently requires lower initial capital costs and almost always requires lower capital costs over the life of the surface mine. Third, it provides comparable operating availability, and finally, it frequently gives comparable operating flexibility - depending on the mine plan. Cost avoidance can be accomplished with modern production methods. These, in turn, permit increased productivity and reduced operating costs such as those for energy, maintenance, and manpower. It has been demonstrated in European surface mines and elsewhere, that conveyor systems frequently require lower initial costs than does truck haulage. Almost always such operations require lower capital costs over the mine life. Those costs include the continual addition of haulage trucks to both accommodate the increasingly difficult haulage routes and fulfill replacement requirements when trucks wear out. Conveyor systems handling ore in numerous large crushing and port facilities, which have operated since the early 1950s, have clearly demonstrated a useful conveyor life of more than 25 years. In contrast, off-highway trucks have life spans of six to eight years. The following examples illustrate comparative capital costs to purchase conveyor systems and comparable truck haulage units. Example 1 The ore haulage route from point A to point B is level and 610m (2,000 ft) long. The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be transported at a rate of 1.8 kt/h (2,000 stph). The installed capital costs to provide a properly designed conveyor that will transport the described material from point A to B is about $450,000. The capital cost to purchase three 77-t (85-st) off-highway trucks and one spare truck - which would provide equivalent capacity - would be about $1.2 million. The truck cost estimate is based on a 6 min. or 771 kt/h (850 stph) truck cycle time. Truck efficiency is estimated at 0.8. Each 77-t (85-st) truck would have an actual haulage rate of 617 kt/h (680 stph). Therefore, three trucks would be necessary to transport the designated tonnage of 1.8 kt/h (2,000 stph). A movable crushing plant would be located at point A for the conveyors and a permanent crushing plant at point B for the truck haulage system. Capital costs for these primary crushing plants were not included in the calculations for either system because the capital costs are frequently comparable. Example 2 The transport route from point A to point B is 610 m (2,000 ft) horizontally and 122 m (400 ft) vertically - on a 20% grade (Fig. 1). The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be moved at a rate of 1.8 kt/h (2,000 stph).

Jan 6, 1983

By F. Mielli

Over the last three years there has been an increase in mining congress and conferences focusing on water management. Water in mining is a key concern for mine managers and operations, and we are now seeing this operational dilemma escalated to the level it deserves. According to Frost & Sullivan research, mining water and wastewater treatment and its related technologies will be a U$3.6 Billion global market in 2016, which translates the importance of this issue. Looking at the current mining trends, some factors increased the importance of water in mining operations, including: ? Future mining investments will be located in geographical locations where water is scarce (water stressed areas) ? A decline in grade will increase the intensity of mineral processes and therefore increase the use of the water ? Increased sustainability and regulations will extend the control/monitoring of water during the entire mine life cycle representation of the mine water flow system. A water balance has several benefits/objectives in a mine operation: ? Mine planning/simulation of mining scenarios/climate change Production optimization ? Minimizing strategic and operational risks ? Social license to operate ? Water-smart mine planning ? Target: water neutral mines ? Benchmarking within and between sites ? Sharing knowledge/technology transfer ? Reporting/communications ? Permitting/Compliance

Feb 23, 2014

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, CWP and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by particle composition, size distributions, shapes). This preliminary study sought to characterize dust from an underground coal mine in Central Appalachia using scanning electron microscopy with energy dispersive x-ray (SEM-EDX). Respirable dust samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate total respirable dust concentrations during sampling. Here we report initial results of this work, and discuss advantages and challenges of particle-level characterization of mine dusts in terms of occupational health research.

Feb 23, 2014

By Roger J. Araujo

A photochromic material is one which undergoes a change of color when exposed to light and reverts to its original color when the light is removed. Review articles carrying extensive bibliographies have been written by Brown and Shaw (1) and by Schwab and Bertelson (2). Organics. Schwab and Bertelson divide the reactions in different organic photochromic materials into some half-dozen categories; Windsor (3) reduces these to the following three main classes of general interest, based on how they work. 1. Stereoisomers. Absorption of light breaks one of the chemical bonds in a. ring molecule, thus allowing the molecule to unwind and form a different geometrical arrangement. The reverse process is a reforming of the bond. Examples of this class are the spiropyrans and the anils. 2. Dyes. A triphenyl methane dye, for example, is oxidized by energetic light; the absorption characteristics of the positive ion so formed are different from those of the original electrically neutral benzene rings. 3. Triplet States. In the class of polynuclear aromatic hydrocarbons, ground-state molecules are excited first to a singlet state by irradiation, and then go, via the lowest triplet state, to an excited triplet state. Visible light is absorbed in the triplet-triplet transition.

Jan 1, 1970