Search Documents

By E. A. Lauha

The Goldstrike Mine is in Eureka County, Nevada, U.S.A., approximately 23 miles northwest of the town of Carlin. The mine is at the north end of the Tuscarora Spur of the Tuscarora Mountains at elevations of 5,300 feet to 5,950 feet. It is part of the Bluestar/Goldstrike sub-district of the Carlin Trend, a northwest alignment of sediment hosted, disseminated gold deposits. The Carlin Trend includes over 15 major gold deposits with production, reserves and geological resources of approximately 65 million ounces of gold (Figure 1). In the Bluestar/Goldstrike sub-district, there are seven major deposits: Betze, Lower Post, Post, Genesis, Bluestar, Purple Vein and Deep Star, plus numerous smaller deposits (Figure 2). Production, reserves and resources for the sub-district are approximately 40 million ounces. Betze and Purple Vein are located on property controlled by Barrick Goldstrike Mines and Bluestar and Genesis on Newmont Gold property. Post, Lower Post and Deep Star occur both on Barrick and Newmont property.

Jan 1, 1993

By J. -M. Lopez-Cuesta, C. Petter, B. Otazaghine, M. Batistella, R. Sonnier

"Kaolinite is a dioctahedral aluminosilicate widely used as paper filler and coating pigment. At the best of our knowledge, kaolinite is not widely used in polymer industry. Therefore, in this study, the flame retardant effect of kaolinite in ethylene vinyl acetate copolymer (EVA) and polypropylene (PP) were studied and compared with an alumina trihydrate (ATH) and Talc. Cone calorimeter results shows that the weight percentage of ATH in EVA/ATH composites must be at least 50 wt. % in order to reach an improvement in fire retardancy in terms of pHRR. In the case of EVA/kaolinite, even with 35 wt. % the pHRR is largely reduced. Comparing PP/Talc and PP/kaolinite composites at 30 wt. %, both fillers leads to same reduction in pHRR with a slightly better performance for PP/kaolinite composites. In both cases an intumescent behavior of kaolinite composites was observed that could slow the rate of the rising degradation products, allowing radical recombination reactions. Also, it was observed that kaolinite forms a protective layer on the surface of the samples, which could insulate the material. These behaviors (intumescence and formation of a protective barrier) could reduce the transfer of the degradation products to the flame and explain the better performance of kaolinite composites. INTRODUCTION The use of mineral fillers as fire retardants in polymer matrix are well known and widely studied [1]–[10]. Aluminum and magnesium hydroxides (respectively ATH and MDH) are the most widely used inorganic fire retardants. To achieve fire retardancy with these mineral fillers, about 50-60% loading is required which decrease the physical properties of the composites. The fire behavior of composite EVA has been the subject of many studies [4], [7], [9]–[15]. EVA copolymers are commonly used in the cable industry, due to their high ductility, even at high loading rates. In such applications, the flame retardant systems should be introduced into the polymer to improve the fire reaction. Many flame retardant systems have been tested but the most used industrially relates to formulations based on hydrated mineral fillers (aluminum hydroxide and magnesium hydroxide). Their low cost and reduced fumes generation explains their success. However, to obtain good performance with this type of flame retardants, it is necessary to incorporate high levels (up to 65 wt %), which severely impact other properties such as processability and mechanical behavior. The main modes of action of these flame retardants are the dilution of the gas phase, the endothermic decomposition and a barrier effect created by the inorganic oxide residue which may be improved by the incorporation of other components such as montmorillonites, silicas or talcs."

Jan 1, 2015

By Gary D. Aho

The United States on a daily basis no consumes about 15MM barrels (2.38 x 106m3) of oil; 5MM (0.79 x 106 m3) of this is imported. This compares tai a daily consumption of 18MM (2.86 x 106 m3) in 1980 when we imported 8MM (1.27 x 106 m3). We are producing the 10MM barrels (1.59 x 106 m3 ) of conventional oil at home from what amounts to just 2% of our domestic energy reserves. Nearly 90% of our total domestic energy reserves occurs in solid forms such as coal, oil shale, and tar sands; this is more than enough to meet our needs for the next 100 years. Worldwide, oil shale is second only to coal as a potential source of energy and the U.S. has approximately one-half of the world oil shale reserves which average over 25 gallons per ton (10.43 x 10-2 L/kg). Since the United States has immense oil shale resources, including some of the richest in the world, and since oil shale produces a superior transportation fuel, it would seem logical that the U.S. would be prudently developing this domestic resource. Unfortunately, despite over 50 years of research and a number of false starts, there is not a commercial shale oil industry in place today. There are a number of recurring roadblocks which have hindered private industry's efforts to develop oil shale and we will look at some of these.

Jan 1, 1983

By H. Maleki

Roof falls continue to affect productivity and safety in U.S. coal mines in spite of significant increases in support utilization in recent decades. To minimize roof stability problems while controlling support effectiveness, the U.S. Bureau of Mines is conducting research on support and ground monitoring techniques. Practical implementation of this research is presented in this paper. Instruments to monitor rock mass deformation, support loads, and microseismic emissions have traditionally been used to assess roof stability. Controlled-source seismic surveys are being used as well. In this paper, measurement techniques are reviewed, and the effectiveness of deformation measurements is demonstrated. This is achieved by an analysis of deformation history from four case studies in room-and-pillar retreat mines. In spite of differences in geologic, geometric, and support conditions in these mines, roof behavior is shown to have been similar prior to failure. The rate of roof movement is suggested as a reliable indicator of roof stability.

Jan 1, 1993

By W. J. Wuest

The U.S. Bureau of Mines (USBM) has recently developed a rock mass classification system for evaluating the structural competency of bedded roof strata; the Coal Mine Roof Rating, or CMRR. When compiled with the companion Lotus 1-2-3 spreadsheet, which is simple to learn and use, CMRR data are a useful tool with applications to longwall gate road pillar design, safety hazard mapping, and artificial roof support analysis. This paper demonstrates these applications under actual conditions found in current U.S. mining operations.

Jan 1, 1995

Mine design and selection of ore processing capacity depend upon a correct estimate of the grade-tonnage distribution. The estimate must reflect what can be recovered and processed. The McCoy/Cove operation in central Nevada, USA, is a gold and silver mine. Case studies of recoverable reserve estimation for gold and silver were made using multiple indicator kriging and the log-affine variance correction. From this model, the grade-tonnage distribution was constructed. Optimal pits were generated by utilizing the distribution, and the results were compared with the pit generated by ordinary kriging. Studies indicate that the proposed method for multi-metal recoverable reserve estimation is more accurate than ordinary kriging in terms of both tons and the grade. Using recoverable reserves for mine design will maximize global recovery of mineral resources.

Jan 1, 1997

To generate a most profitable ultimate pit limit is generally the first step in mine design. This paper presents a new graph theory oriented, optimum ultimate pit limit design algorithm which will maximize the total undiscounted net profit. This algorithm performs much better than the well known Lerchs-Grossmann algorithm, in terms of the reduction in computation time and computer memory requirements. This algorithm operates on many directed trees in a graph, where each vertex in a tree represents a block in the mine model. The formation of each directed tree is based more on the ore-waste support concept than the geometry constraints alone. The general procedures of the algorithm, programming considerations and two case study results are discussed in the paper.

Jan 1, 1990

By B. M. Davis

Frequently ore reserve studies utilize samples from a series of drilling or other types of sampling campaigns. Sometimes there is a mix of sample types, say for instance, channel samples from underground workings and drill core from surface drilling. Since drilling, sampling, logging, and sample preparation protocols tend to change over time, there is always a question whether the samples give similar results that vary only by chance alone. The problem of comparing the various campaigns is complicated by the presence of spatial relationships among the samples. Geostatistical tests take the spatial correlation into account, but these tests may be complicated and cumbersome to implement. A comparison method based on familiar statistical graphics is presented which accounts for the spatial relationships. It allows comparisons to be made quickly by using simple statistical graphs such as scatterplots and boxplots.

Jan 1, 1996

By H. F. King

In 1982, the result of a 3-year study was published as "A Guide to the Understanding of Ore Reserve Estimation". The principal conclusions were that computation formed only part, and perhaps not the most important part, of an estimate and that the estimate should recognize that geological, mining engineering and metallurgical judgements formed an essential part of the eventual result. Subsequent expectation/realization studies of several mines have produced case histories which form the principal basis of the paper. These imply that geology is even a larger factor than thought earlier.

Jan 1, 1985

By R. W. Amstutz

Abstract. The shaft was drilled on U.S. Government land in the Piceance Creek Basin and was funded by the U.S. Bureau of Mines. It was drilled to 723 meters (2 371') to provide access to rich deposits of oil shale, nahcolite and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual string, reverse-air, jet-assist circulation methods were used. Drilling required 8 months. Site preparation, running and cementing the casing required another 4 months. A 2.44-meter (96-inch) ID steel welded casing, 5.1 cm (2 inches) thick was installed and 2 700 tonnes (63 000 sacks) of cement were slurried and pumped into the annulus.

Jan 1, 1980

By C. E. "Sam" Lovewell

In approaching a discussion of production of cement, I hope I won't be like the porter in the bank who was asked if he could give some details on the rediscount rate. He replied, "Boss, when I said hello, I told you all I know." Need for change every so often is illustrated by the story of the little boy four years old who had not spoken a word in those four years. One morning he said, "This damned oat meal is burned'." His Dad was amazed and said, "Son, how come you haven't said a word for four years and now out of a clear, blue sky you say, "The oat meal is burned." Johnny said, "Well, up to now everything has been all right." Not being a mining engineer myself, and my subject not dealing with mining engineering directly, I can only hope that you will agree that the subject has current relevancy by the feet that it can materially improve our environment by putting to good use a potential environmental polluter; namely, fly ash. The profitable utilization of fly ash can reduce cost of use of coal as an energy source. Therefore, it behooves us all to explore to the greatest depth, the pluses and minuses occasioned by its use wherever possible. My particular subject and my particular interest lie in its utilization as a blend in the production of Type IP Portland-Pozzolan Cement meeting requirements of ASTM C-595, Type IP.

Jan 1, 1974

By B. Y. Wong

In April 1989, Southern Company Services signed a 3.5 year contract with DOE-PETC for generic engineering development of an advanced physical fine coal cleaning technology known as selective agglomeration. This technology offers the potential for significantly higher pyritic sulfur removal (90% +) than conventional coal cleaning (30 to 50%) while maintaining high Btu recovery (90% +). Engineering development will include bench-scale process development; component development; adaption or modification of existing unit operations; proof-of-concept (POC) module design, fabrication, testing and evaluation; and small commercial facility conceptual design. The information obtained during POC operation will be sufficient to result in a technical and economic design base that can support construction and operation of a small commercial plant. The major goal of the research is to develop selective agglomeration technology to achieve 90% pyritic sulfur removal while operating at Btu recoveries above 90% based on run-of-mine quality coal. This objective will be accomplished in two phases: Phase 1 -bench-scale and component development, and Phase 2 -POC module operation and conceptual design of a small commercial plant. Currently, work is proceeding under Phase 1 (Tasks 1-7) of the project. A review of the status of Tasks 1-7 is presented in this paper.

Jan 1, 1991

By Gerald L. Colborne

The major role of financial institutions in the free world in the development of mineral resources is to provide the necessary capital in the form of loans to underwrite the development of these resources by the industry on a stable and continuous basis. This capital provided by the depositors to the bank must be invested in sound projects where the degree of risk is relatively small, the return on the investment is reasonable and the time to retire the loan is of short duration. Money is, therefore, one of the important ingredients along with technology, manpower and an exploitable resource that will provide a sound economic base in this region of development. Canadian banks are similar to banks of other western nations, although each country has some differences in their banking systems. The basic difference between the American and Canadian systems is that the former employs unit banking while the Canadian utilizes the more mobile branch system, which is prohibited or restricted in the United States and some other countries. Canadian banks are the subject of this paper, so, subsequent material will relate to Canadian banks unless indicated otherwise. It will be realized by everyone that the mineral industry is only one area of the economy in which the banks are interested and to cover the subject matter in the time allowed, the topic is restricted to mineral resource development. In Canada this is a vital sector of our economy and before we outline some of the details of financing and services involved in various aspects of mineral development, a review of the Canadian mineral industry is a necessary part of the sequence of presentation. The writer presents this material as a resource engineer advising a major bank in mineral matters, so the presentation may relate more to the financial problems of the developer

Jan 1, 1972

By S. A. Shoop

Vibrations from thirty-seven blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations reported in the U.S. Bureau of Mines studies. Regulations based on USBM data could then be too conservative or lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1983

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

By C. D. Elifrits

The required reclamation of land disturbed by surface coal mining often results in the creation of some over steepened slopes which are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has indicated that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations will be summarized in this paper and field results shown.

Jan 1, 1986

By C. H. Sheerin

Remotely located in the jungle near mount Puncak Jaya [16,500 ft (5,030 my), Irian Jaya, Indonesia rests Freeport's Indonesian copper mining operation. Shortly after start up of Freeport's copper concentrator in 1972, lower than estimated throughput was experienced within the crushing circuit. Within one year, Freeport had successfully engineered a solution, and was operating a 5,500 dmtpd wet screening circuit. Today, after 19 years of successful wet screening expansion and operation, the concentrator processes 57,000 dmtpd.

Jan 1, 1993

By S. Pollak, J. Rickard

The Long Baseline Neutrino Facility Far Site in Lead, South Dakota is currently under construction and involves drill and blast excavation of the largest and deepest caverns in North America. This paper will review how the geotechnical risks are being managed through careful consideration of excavation sequence, completion of exploratory pilot tunnels, implementation of a robust instrumentation and monitoring program, and validation against the design. Aside from having a cross section of 5,900 square feet and being situated at a depth of one mile, the caverns also employ a unique permanent rock bolt solution which underwent a significant pre-production pull testing program involving varying installation methods and being subject to blast vibrations. The behavior of the schistose rock mass and performance of the ground support are being continually monitored throughout the construction phase.

Jun 13, 2023

By Charles A. Rhoades

The Bureau of Mines is conducting research on a dual leaching method that offers the potential for the economic recovery of the silver as well as the manganese contained in some of the domestic manganiferous silver deposits. The method is an initial leach of the manganese with aqueous SO2 followed by a neutralization rinse, and then by a second leach for the extraction of silver with cyanide solution. Refractory silver in these ores is either bound by the high-valence manganese, chemically resistent to cyanide leaching, or is rendered inaccessible to cyanide leach solution by the surrounding manganese mineralization. Less than 10 pct of the silver was extracted when -1 in +1/2 in (-2.5 cm + 1.3 cm) ore pieces were leached directly with cyanide. However, extractions of 25 to 82 pct for silver and 65 to 96 pct for manganese were attained in laboratory column leach tests using the dual method on the same size ore pieces from six domestic deposits.

Jan 1, 1984