Search Documents

By Thomas R. Kuesel

Just south of the L'Enfant Station in Seventh Street, the WMATA system splits into two branches, each comprising twin single-track soft ground tunnels. Immediately at the beginning of the section, Interstate Route 95 crosses transversely over the alignment in open cut, removing most of the cover over the tunnels. Seventh Street spans I-95 on a bridge whose abutments and pier also cross transversely over the four tunnels, with their footings as little as 7 feet above the tunnel crown (Figure 1). Soil investigations revealed that the tunnels would have to be driven through mixed face, with a clay invert and a waterlogged sand crown. Thus, there was a good chance that the roof would fall in, leaving 1-95 and the Seventh Street Bridge in a crater. Since there was no roof that could be counted on, these were figuratively (and potentially truly) Washington Metro's Topless Tunnels (Figures 2 and 3). DESIGN ALTERNATIVES Faced with this situation, the designers considered several options, including temporary detours that would permit demolition of the bridge and building tunnels under the 1-95 Freeway by cut-and-cover methods. They also investigated structural underpinning of the bridge and freeway pavement, and strengthening the bridge abutments and center pier by post-tensioning to enable them to span over any subsidence trough.

Jan 1, 1976

By H. M. Ray

The discovery of the New Lead Belt in the mid-'50s began a search for mill design criteria that is continuously updated. The opportunity to design, construct, and operate four new mills in the span of 20 years provided fertile areas for new concepts. The central theme for design parameters encompassed simplicity, functional, and economic consideration. Ore characteristics for each plant remained relatively constant, providing stable criteria for grinding circuits. Bond index nominally 10-12. Flotation circuit parameters were based upon power application with 10-20% excess capacity built-in to protect recovery. Newer equipment exhibits greater power application efficiency lowering horsepower requirements per ton. Instrumentation was installed to stabilize circuits, protect equipment, and improve products. With ever increasing requirements of higher quality products, environmental considerations, and operating cost pressures, the upgrading of operating procedures is in a constant state of flux. Installation of more efficient equipment, chemical processing, or any other technique would be considered as feasible. Current practice is for St. Joe to design and engineer in-house its own plant design. The exception being detailing of structural steel. It is felt that familiarity with past design criteria serves as a valuable foundation to incorporate changes. Also, direct contact with operator provides specific data, and feedback for constructive criticism that is utilized for defining and correcting problems. The results are in reality an operator's plant with the benefit of advancing technology that meets the demands for improved products without sacrificing the economies of throughput or recovery.

Jan 1, 1977

By James M. Barker

The borate deposits of Death Valley, first exploited in 1882, were a major world source of boron-bearing products until shortly after very large deposits near Boron, California (Kramer) came on stream in 1926. Borate mining in Death Valley then became moribund, with most extant deposits held as reserves backing Kramer. Tenneco began borate operations following acquisition of claims in 1967 and is the only active borate producer inside Death Valley National Mon¬ument. Borate ores, confined to the lower Furnace Creek Formation (early to middle Pliocene), initially precipitated in a shallow lake fed by boron-rich volcanic hot springs associated with the Basin and Range province. Later diagenesis and remobilization plus regional folding, faulting, and erosion altered and complicated originally simple borate mineralogy and distribution. Dominant ore minerals are ulexite (NaCaB509.8H20), probertite (NaCaB509.5H20), and colemanite (Ca2B6011.5H20). Tenneco currently operates two open pits near Ryan, California. Mining is by bulldozer-pushed scrapers hauling waste and front-end loader/off-highway truck combinations for ore and waste haulage. Archeological, environmental, and aesthetic considerations influence both mine plans. Boraxo Pit, opened in 1970, has deep ore (stripping ratio 10 to 13:1) which occurs along a fault and as beds in shale on the hanging wall. Problems include pit wall instability (adverse bedding), non¬ripable calcareous shale (11,000 fps), and mixed ore separation. Sigma Pit, opened in 1975, has shallow (stripping ratio 1 to 1). low dipping, bedded ore in shale. Massive ulexite and "granular" un- cohesive colemanite present problems in mining and milling. Colemanite is crushed to -6 inches, washed, dried at 350°F, then calcined at 800°F with 100 tpd capacity. Crushed (-6 inch) ulexite or probertite is Raymond milled to customer specifications with a capacity of 1000 tpd.

Jan 1, 1976

By Mohan Dutt

This paper is concerned with applied platinum resistance thermometry which involves many considerations absent in precision thermometry. The historical development of the Callendar-Van Dusen Equation which describes the resistance- temperature relation of pure platinum is discussed. The advantage of using platinum resistance temperature sensors over thermocouples is described, and the improvements in design and construction of these sensors that have come about in the past few years are discussed. Integral and remote bridges that convert resistance changes into voltage together with signal conditioning techniques and equipment for voltage or current signals are described. Errors encountered in temperature measuring schemes and methods to reduce these errors are summarized.

Jan 1, 1969

By J. Hahn

Modern high-performance disc filters such as the BoVac Disc Filter have set new standards in applications where large capacities of solids, liquids and air have to be managed through the filters. These disc filters have an enormous hydraulic capacity. For applications in mineral processing - with a special focus on tailings – which typically have high solids throughputs but low filtrate and air flows, this capacity can be used to expand the filtration area while maintaining the benefits of very good cake discharge even with thin cakes (4-5 mm) and a high filter speed. Research work over the last century has proven that increasing the filter area should be achieved by increasing the disc diameter. Because adding more discs leads to big problems with the cake discharge. However, as the disc diameter increases, the filter segments become longer and heavier. A suitable compromise was therefore found by doing both. The result is the first vacuum disc filter that offers significantly more than 300 m² of filtration area, but has no more than 6 discs.

Feb 1, 2023

By C. Jack Powell

TVA's involvement in air quality programs is perhaps a bit unique. The Tennessee Valley Authority was established in 1933 as a regional resource development agency and therefore must view clean air and clean water as essential resources for the overall development of the Tennessee Valley region. TVA operates certain resource development and production facilities, including power-generating facilities, which are potential air pollution sources. The remarks in this paper will be restricted to air pollution control technology at power-generating stations. Perspectives of Air Pollution Control The art of pollution control must be viewed from several perspectives: 1. It must be viewed in a time perspective--what is available now for air pollution control, what might be available in the near future, what are the likely technologies for the more distant future, and what the future trends in availability of resources might be. 2. Each air pollution abatement scheme must be viewed in the perspective of its total environmental consequences--not just its ability to clean up the air. The generation of electricity from coal produces waste gases, waste particulates, and waste heat. These wastes must be disposed of either in water, in air, or on land. If the polluting wastes are removed from the gas streams going into the air, then they must be disposed of either on land or in water or, hopefully, converted into a product which has some beneficial use. As an example, removal of S02 from stack gases could be more readily accomplished if one could dump waste sulfur products in water. He would solve an air pollution problem by creating a water pollution problem. 3. Techniques for air pollution control must be viewed in the perspective of regional, national, and world resources with their national security and economic implications. The power industry might reduce air pollution by switching generating plants to burning desulfurized fuel oil or natural gas.

Jan 1, 1972

By Raja V. Ramani

In many instances, the actual production from a longwall face does not equal the planned capacity. General problem areas which have been identified include face length and panel depth, face area and gate entry roof support, face conveyor and shearer wear, outby haulage system failures, number of entries in longwall gate development and longwall move time. The performance of a longwall face is totally dependent on the interaction of these and many other factors. To explore fully these interactions, a systems analysis of longwalls has been performed. In this paper, the systems approach, the factors considered in the analysis, and the results of the analysis are presented.

Jan 1, 1983

By Sahin Furkan Sahiner, Onur Golbasi

Effective maintenance planning is vital for coal mining operations, where haul truck fleets directly determine production continuity. This study presents a discrete event simulation (DES) model for evaluating maintenance strategies under multiple failure modes and their interdependencies. The model integrates corrective, periodic preventive, and opportunistic maintenance, dynamically updating equipment lifetimes through probabilistic time-betweenfailure and time-to-repair distributions. Applied to a fivetruck coal haulage fleet over a one-year horizon, results show that periodic preventive maintenance delivers the highest availability (76%) under unconstrained conditions, slightly outperforming corrective-only maintenance (75%). Opportunistic and integrated approaches performed worse (68% and 69%), reflecting redundancy from overlapping interventions. These findings suggest that structured preventive programs provide the most reliable outcomes when costs and resources are not limiting. The DES framework serves as a baseline for future models incorporating cost, spare parts logistics, and workforce availability, supporting robust maintenance planning in coal mining operations.

Feb 22, 2026

By X. Y. Yu, X. A. Wei, A. Zeng

"The flotation behaviors of diaspore and three kinds of silicate minerals - kaolinite, illite and pyrophyllite - using an organosilicon cationic surfactant as collector were investigated as functions of reagent concentration and pulp pH. The results show that the organosilicon cationic collector QAS122 is a suitable collector for the flotation of aluminosilicate minerals but has weak collecting ability with regard to diaspore, enabling the flotation separation of diaspore from silicate minerals using QAS122 as collector. The flotation of a bauxite ore was then studied in detail. Finally, a reverse flotation separation process was used to process a low-grade bauxite ore. It was concluded that use of the organosilicon cationic collector is effective. A concentrate with aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, of 9.67 was obtained from natural bauxite ore with A/S of 6.07 at pH of around 11. The Al2O3 recovery rate was 81.72 percent. IntroductionChina has abundant bauxite ore resources, but more than 98 percent of the bauxite ores are the diasporic type, with the characteristics of complex mineral composition, low aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, and difficulty of processing. The gangue minerals in bauxite ores are mainly kaolinite, pyrophyllite and illite, containing titanium and iron impurities (Zong et al., 2008). It is known that high-grade bauxite ore, with A/S greater than 8, can be processed directly by the Bayer process (Papanastassiou et al., 2002; Ma et al., 1996). However, Chinese diasporic ores have been processed mainly by the sintering process, which is environmentally damaging and energy intensive. Increasing the A/S of the diasporic ores using a flotation method is needed (Xia et al., 2010).Froth flotation is one of the most widely used processes to concentrate valuable minerals in beneficiation ores. It is particularly useful for separating finely ground ores from their associated gangue minerals. For diasporic bauxite ores, flotation is applied to obtain high-quality material for the Bayer process by increasing the A/S. Direct flotation has been shown to be an efficient method for the desilicating of diasporic bauxite ore (Wang et al., 2004; Xu et al., 2004), but reverse flotation has more advantages for this purpose, including less collector consumption, less foaming product and less effect on metallurgy (Liu et al., 2007; Hu et al., 2003; Hu, 2003; Luo et al., 2001)."

Jan 1, 2015

By F. Sill

The disposal of residual material from processing and combustion of coal, from incineration of domestic refuse and sewage sludges kind to the environment is a prior task for the future. Deutsche Montan Technologie (DMT) has developed a new technique which makes possible to fill-up goaf cavities behind running caving systems in coalmining. In a mixing and pumping station on the surface high concentrated suspensions are produced from the above mentioned materials. The paste is pumped through pipes to the coalfaces and via trailing discharge pipes stretched to the fracture zone in the caved-in goaf. Since three years a special designed plant is working successfully on a coal mine of Ruhrkohie AG.

Jan 1, 1994

By R. Bhaskar

The control of quartz levels in the respirable dust requires an approach different from that used to control respirable coal dust. The unique physical properties of quartz have to be utilized when developing quartz dust control systems. Also, techniques that modify the surface properties of quartz dust so that conventional dust control measures are effective should be explored. For instance, the wetting characteristics of quartz can be modified so that the capture efficiency of the quartz dust can be improved. Foam sprays assist in modifying surface wetting characteristics. This paper summarizes the results of a study that was conducted in an operating mine to evaluate the effectiveness of a compressed air foam spray system installed under the boom of a continuous miner and directed so as to cover the pan and the gathering arm. The objectives of the study were to evaluate the effect of the foam underboom sprays on (1) the respirable dust concentration in the ambient air, (2) the quartz concentration in the respirable dust. The engineering design of the foam generation and delivery system is described in the paper, followed by a description of the mine and the dust sampling strategy. The data were analyzed to study the effect of foam on respirable dust and quartz concentrations at the miner cab, face return and the intake. The results of the data analyses and costs are presented in the paper.

Jan 1, 1991

By A. E. Jack Swanson, Brian P. Micke

INTRODUCTION Nevada Goldfields began underground mining development at the Kingston Project in September, 1986, followed by mill start-up in March, 1987. The first gold pour in April followed three years of preparatory work in establishing a North American operational base for the production of precious metals by Golconda Minerals N.L., an Australian mining firm. GENERAL CORPORATE BACKGROUND The Golconda Group of companies was established in early 1983 in Australia. It began operations by successfully retreating tailings at several old gold mining sites throughout Australia. With the limited reserves available for tailings retreatment, Golconda began to look toward the future by conducting a gold exploration program in Australia. However, the continued high price of gold in Australia had limited the possibilities of acquiring good properties at a reasonable cost and consideration was given to looking outside Australia in addition to Golconda's domestic exploration activities. North America was favored because of the proven potential for substantial gold deposits, the established infrastructure which would allow for rapid and cost-effective development of new projects and the advantages of similar political and economic climates. In mid-1984, Golconda established an office in California and began an extensive study of over 100 prospects throughout the United States. Two prospects were identified as a result of this study whch showed merit; one was located at Empire, Colorado and the other at Aurora, Nevada. Negotiations were then successfully undertaken to acquire these two properties. Golconda's U.S. offices were moved to Reno, Nevada in early 1985 to facilitate management of its projects. To operate and manage these projects, a small Canadian company listed on the Vancouver Stock Exchange, Cannon Minerals, was acquired by Golconda and renamed Nevada Goldfields Corporation. The current structure of the company is shown below in Figure 1. A private placement of 2,575,000 shares of common stock at US54.00 per share was arranged by Jacksons Limited of Australia in association with W.I. Carr (U.K.) Limited of London. This placement resulted in US510.3 million being available in May, 1986 for the acquisition and initial development of the Aurora and Empire projects. While the financing was underway, project planning commenced on both the Aurora and Empire projects. The Aurora project was selected as the one to be initially developed because of its relatively advanced stage of development. The

Jan 1, 1987

By R. L. Summers

The tremendous engineering advances occurring during this past century are very evident within the boundaries of the Anthracite Section of AIME. The Steelton plant of Bethlehem Steel Corporation, located along the Susquehanna River just east of the Commonwealth's capital at Harrisburg, for more than 105 years has experienced a most dynamic life which has paralleled America's industrial growth. (Figure 1) In June 1865, just after the Civil War, a group of men met to organize the Pennsylvania Steel Company. The war had brought into sharp focus the vital importance of the railroads to the country's expansion. Until that time wrought iron rails were used, and the replacing of track after only several months wear had become an almost unbearable cost. The spirit of free, competitive enterprise and the prospects of a lucrative market compelled these men to form that first Pennsylvania Steel Company and to develop better rail products. They issued the following statement: "...our desire to free ourselves from dependence upon a foreign market (has) led to the organization of the Pennsylvania Steel Company, and the parties who have connected themselves with it are determined to produce upon American soil all the principal manufactures of steel that are now, at such a serious cost for freight, commission, insurance, exchange, duty, etc., and often, with so much delay and uncertainty, imported from abroad. (We) are preparing to establish near the consumer, works at which articles of accustomed pattern will be promptly produced, and from the

Jan 1, 1971

By Guy D. Bruno

Through the remainder of this century, world consumption of fluorine per ton of primary aluminum produced will continue to be substantially reduced. Growth of the primary industry will offset some of the unit consumption, but demand for new fluorine sources will decline sharply. Continued application of dry fume scrubbing systems will be the most significant factor in reducing demand.

Jan 1, 1978

By George F. Swindle

This paper discusses a composite of two coal reserve studies, each of which made use of a computer-based modeling system to assist in an evaluation of multi-seam deposits. The model permitted simultaneous consideration of seam thickness, seam structure, overburden thickness, over-burden ratio, and quality parameters for sulphur content, ash content, BTU values and the EPA Compliance index. The model is designed for use by a non-programmer, geologist or mining engineer. It enables the user, from a computer terminal in his office, to specify constraints (for example maximum um sulphur and maximum- ash content, minimum seam thickness and minimum BTU rating), and produces a report showing the volume, quality and location of that part of the total in place deposit satisfying all the constraints.

Jan 1, 1983

By A. T. Yu

There are compelling reasons for us to look to our Country's Western coal. Despite its inherent low BTU content, Western coal's low sulphur content provides a near-ideal answer to satisfy our in- dependent goals of clean air and self-sufficiency in energy. Vast reserves, thick seams and amenability to low-cost strip mining serve as a powerful economic basis for its viability as a primary and dependable source of energy for the coming decades. A major consideration, the solution of which may not be quite obvious, is transportation cost. These abundant deposits are remote from the utilities of the heavily populated eastern regions of the United States (Figure 1). A Western coal mine in Montana is likely 1500 miles or more from an eastern power plant. The comparable distance to an eastern coal mine may be only 200 miles. Thus, the question is: How can the haulage cost of our Western coal be substantially reduced to an acceptable level? If resolved, western reserves of coal will be one of the key solutions to satisfying our Nation's energy needs.

Jan 1, 1975

By Zibo An, Yong Hu, Hao Zhang, Hong Cao, Jun Xue, Zhen Luo

Phosphogypsum (PG) is a by-product of solid waste produced by the phosphate chemical industry. Owing to large emissions and massive storage issues, it causes a potential threat to our environment. Hereby, a method based on the precipitation and crystallization properties of calcium phosphate-magnesium ammonium phosphate (CP-MAP) followed by its adsorption on active solid waste powder is used as the main principle to treat PG harmlessly. The treatment process and its influencing factors for orthogonal experiments along with the associated environmental safety have been studied in detail. The results showed that this method could simultaneously remove soluble phosphorus and soluble fluorine from PG. When ACP, FA, HBM, and Ur were added to PG at a dosage of 3%, 13.5%, 0.04%, and 0.04%, respectively, the residual phosphate and fluoride contents was 0.061 mg/L and 0.856 mg/L respectively in the PG leaching solution. Compared to state-of-the-art approaches, this method exhibited higher efficiency in removing phosphate and fluoride. Most importantly, this method does not cause any secondary pollution in the process, thereby showing a novel application in large-scale industrial treatment.

Aug 29, 2022

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By P. M. Yavorsky

Using a mine roof simulator press capable of duplicating the expected magnitude of vertical and horizontal forces experienced by underground mine roof supports, load capabilities of some roof support cribbings were measured. Comparative ultimate vertical support strengths are reported for cribs of old and new timber and nonreinforced and steel-fiber-reinforced (SFR) concrete blocks. In terms of load- bearing capability, cribs of new hickory and nonreinforced concrete blocks have about equal strength, and SFR concrete blocks are three times as strong. Wood aged 2 years underground lost 43 pct of its support strength. These data were obtained during the course of the initial familiarization exercise of the complex press.

Jan 1, 1984

By E. Milosavljevic, C. H. Bucknam, K. L. Gabby, T. C. Eisele

"Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately, mercury is recovered along with the silver as mercury/silver/gold amalgam, which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution. IntroductionThe dissolution of mercury along with precious metals during cyanide leaching is a long-standing problem, which can result in significant mercury toxicity issues (Washburn, 2003). Mercury is first dissolved by the cyanide solution, and then, since it has a great deal of chemical similarity to silver, it follows silver throughout the concentration and recovery processes, ultimately being recovered as a silver/ mercury amalgam when the metal is precipitated by either the Merrill-Crowe process or by electrowinning.While it would be desirable to either prevent mercury dissolution entirely while still allowing silver dissolution, or to selectively capture mercury before the precious-metals recovery step, there is not yet an effective and economically practical approach to doing this (Grosse, 2003; Ravichandran, 2004; Misra, 1998; Pai, 2000). There are a few processes that have been proposed, such as differential adsorption. While activated carbon, as used in the carbon-in-pulp process, is not highly selective between mercury and silver (Washburn, 2003), it may be possible to achieve some separation by selective elution of the carbon to produce high-mercury and low-mercury eluates (Bunney et al., 2010). Certain synthetic resins were shown to be selective for gold but are more expensive than carbon, requiring special equipment, and have not yet been shown to be selective for mercury (Grosse, 2003). There may be potential for differential dissolution approaches, as thiosulfate leaching does not dissolve mercury sulfides as readily as it dissolves gold (Oraby et al., 2010), and it is possible that it may be similarly more selective for dissolving silver relative to mercury. Some work has also been done with selective precipitants, such as sodium polythiocarbonates (Bucknam, 2007), and 1,3-benzenediamidoethanethiol (Matlock, 2002). Common problems with these approaches include introduction of a solid:liquid separation step, reagent costs, the need to measure the mercury concentration for process control for minimizing silver losses, and regulatory requirements to retort otherwise stable mercury concentrates."

Jan 1, 2015