Search Documents

By Stan Tang, Yiming Sun, S. Amir Reza Beyabanaki, N. Sathi Sathialingam

The Kurve mixed-use development project including a 22-story tower at 2801 Sunset Place was constructed on a site consisting of a roughly rectangular-shaped lot at the intersection of Wilshire Boulevard and Hoover Street in Los Angeles. Two Metro Red Line tunnels, with depths of approximately 30 feet and 58 feet, respectively, cross below the building at distances of approximately 1 foot to over 63 feet from the site. This paper presents numerical modeling performed to evaluate the ground and tunnel behavior in response to building construction. Results of geotechnical instrumentation and monitoring undertaken during the building construction are also discussed.

Jun 13, 2023

By Pratama Mochamad Rizki, Andika Satya

High-risk area in open-pit mining should always be monitored by the operational supervisor because of its nature. One of this type is the soft soil dump area. Due to the unstable bearing capacity of the soil, it’s highly possible for us to find cracks in the area. This paper aims to build computer vision which able to detect truck’s distance from safe limit allowed during dumping activity. The system will warn the truck’s driver if the truck has crossed that predetermined safe limit.

Jun 25, 2023

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

"From 2011–2016 there were 1,511 documented injures, including 7 fatalities, from ground falls in U.S. underground coal mines. The majority of these ground fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely utilized in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Mine Roof Simulator (MRS) in Pittsburgh, PA. The load-displacement characteristics of a 2.4-m x 3.7-m panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of displacement loading rate, load pull surface geometry, and the inclusion of roof channel on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines. INTRODUCTION Over 1,500 injures, including 7 fatalities, occurred from 2011–2016 from ground falls in U.S. underground mines with the majority of these ground-fall injuries caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Comptonet al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Pittsburgh Research Laboratory (PRL)."

Jan 1, 2018

By A. C. Smith, J. H. Rowland III

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) established a Technical study panel (the Panel) to provide recommendations on the utilization of belt air and new technology that may be available for increasing the fire resistance properties of conveyor belt used in underground coal mines. The Panel Report recommended use of the belt evaluation laboratory test (BELT) as the method for testing and approval of flame resistant conveyor belts used in underground coal mines. The research conducted to establish the correlation of the BELT with large-scale belt fire flammability tests was done using 91 - 107 cm (36- to 42-in.) wide conveyor belt. Due to today’s coal haulage capacity, the mining industry is using 183 cm (72 in.) and wider conveyor belts. The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine if the BELT will also qualify wider belts as fire resistant for use in underground coal mines. This paper describes the results of recent experiments comparing results from using the BELT and the large-scale tests for six different belts.

Jan 1, 2011

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method tradition-ally solves each mesh equation by an approximation during each iteration. It is thus interesting from both theoretical and computational viewpoints to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation, which has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the two solutions.

Jan 1, 1997

By Y. J. Wang

This paper deals with the application of linear programming to the solution of mine ventilation network problems which involve only the controlled splitting of air. An airway whose air quantity is to be controlled to a prescribed value is called a "fixed-quantity" airway. In a network where the fixed-quantity airways are increased in number and are distributed such that the air quantities for the remaining airways are uniquely determined by Kirchhoff's first law, the problem reduces to determining the head losses and locations for air regulators and fans. This is one of the network problems encountered most often in underground coal mines. By formulating Kirchhoff's second law as a set of linear constraints and the total air horsepower supplied by fans as a linear objective function which is to be minimized, the problem is analyzed through the technique of linear programming. Some important properties of the problem are discussed and examples are presented.

Jan 1, 1971

By A. Hajati

The main purpose of this study was to find the optimum values for factors affecting the Zn recovery rate using oxine or dithizone as a chelating agent collector during flotation in a Hallimond tube. Eight control factors, including four levels of pH, oxine/dithizone, corn starch, sodium thiosulfate, sodium citrate, sodium silicate, conditioning and floating durations were considered in a Taguchi experimental design technique. An L32 orthogonal array was applied to determine the signal-to-noise (S/N) ratio. Analysis of variance (ANOVA) was used to determine the optimum conditions and the most significant parameters affecting the reaction rate. Analysis of the experiments using the Taguchi approach indicated that pH had the highest contribution to the recovery rate of zinc oxide particles. The results showed that the recovery rate of zinc increased by 43.4 ± 3.0% and 24.9 ± 3.2% using oxine and dithizone, respectively, under optimum conditions with a confidence level of 90%.

Jan 1, 2010

By R. L. Garrett

The quality of mineral additives used 1n a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally used minerals are bentonite, barite, barite/hematite blends and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity, gel strength and to provide a low permeability filter cake. A multi-million dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason why oil companies who use these materials sometimes set their own quality standards beyond those already specified in API Spec. 13A. Also discussed in this paper are the current standardization activities in API Committee 13 on these minerals.

Jan 1, 1986

By P. D. Rao

Although phosphorus is a very important biogenic element, its concentration in coal is generally low. Phosphorus concentrations typically range from 0.001 % to 0.229% in raw coals of the contiguous 48 states. Some Alaskan coals in the Cook Inlet region contain horizons unusually high in phosphorus. A foot by foot analysis of deep drill core, containing 70 ft. of sub bituminous 'C' coal from the Beluga coal field, Alaska, showed certain increments contained as high as 17.03% P2O5 in the coal ash; 1.01 % P on a moisture-free coal basis. Crandallite has been identified by electron microprobe analyses as a phosphorus numeral in these coals. The authors could quantify calcium, barium, strontium and phosphorus concentrations from the coal attributable to crandallite. These high phosphorus coals provided a unique opportunity to study the association of phosphorus in coals using chemical fractionation for exchangeable cations and acid extractable elements. Since the source of high phosphorous horizons in Cook Inlet coals is attributed to volcanic ash, it is suggested that the profiles of acid extractable phosphorous concentration may be useful for coal seam correlations.

Jan 1, 1992

By Ping K. Di

A naturally aged and synthesized manganese oxide-coated granular media was found in our laboratory to have the capability of the removal of soluble Mn(H) from mine drainage by adsorption and oxidation. Mine drainage commonly also includes other heavy metal ions. Extending this principle, this paper presents the removal of heavy metals including lead, copper, cobalt, zinc and nickel in the aqueous solution by using the synthesized manganese oxide-coated granular media. It was found that the adsorption of lead, copper, cobalt, zinc and nickel on the manganese oxide-coated media follows both Langmuir and Dubinin-Radushkevich adsorption isotherms except in the concentration range less than 0.1 mmole/L. The adsorption mechanism involves the ion exchange between the heavy metal ions and synthesized manganese oxide coated on the media. The synthetic manganese oxide surface has a strong metal binding ability to the heavy metals in the order of Pb2+ > Cu2+ > Ni2+ > Zn2+ > C02+ based on the adsorption results using batch and continuous column operations. The breakthrough curves of these heavy metals showed that the synthesized media could be used effectively in the removal of these heavy metal ions in a cell or packed column. The process can simultaneously facilitate the immobilization of the heavy metals on the synthesized manganese oxide coated media. A subsequent pH adjustment dislodges the heavy metals and regenerates the synthetic media. Thus, the process accomplishes the adsorption, immobilization and concentration of the heavy metal from waste stream in one monolithic procedure.

Jan 1, 1995

By Richard M. Chamberlin

Perlite is an altered rhyolitic glass with 2 to 5 wt % water that expands or "pops" when heated quickly to plasticity while evolving steam to form lightweight, glass foam. Commercial perlite deposits in New Mexico are well-developed zones of chemical weathering (hydration) superimposed on highly permeable and thick glassy zones at the chilled upper surface and toes of high-silica-rhyolite lava flows and lava domes. The maximum tonnage of glass in these volcanoes was predetermined by their unique eruptive histories. New Mexico perlite production (80% of US production of 571,00 st) is mostly from the 3.9 Ma high-silica-rhyolite lava flows at the No Agua Peaks volcanic center. The primary vent at No Agua is defined by a 900 ft-high rubidium-rich composite lava dome, known as West Peak, that contains minor perlite reserves. Slightly less rubidium-rich lava squeezed out from under the west flank of the dome to form relatively thin (250 ft) but highly vesicular lobate flows that now consist of about 50 % recoverable perlite. Finally, rubidium-poor lavas were extruded from a radial dike on the northeast flank of the dome. These thicker (400 ft) flow lobes contain about 20 % recoverable perlite. The largest mass of lava does not always contain the most perlite. The thinner (west) flow at No Agua yields the largest perlite reserves rather than the large composite lava dome or thicker (east) flow.

Jan 1, 1994

By M. Schlegel, J. A. Villa Mena, R. E. Vivas

ArcelorMittal, headquartered in Luxembourg, is one of the world’s largest steel and mining companies. It supplies steel to industries such as automotive, construction, and energy, with a strong emphasis on sustainability and innovation. The company employs about 125,000 people and, in 2024, produced 42.4 million tons of iron ore and 57.9 million tons of crude steel across 15 countries. Its mining operations span Canada, the United States, Mexico, Brazil, Ukraine, Bosnia and Herzegovina, Kazakhstan, and Liberia, focusing on iron ore and coal extraction to support steel production. This study examines Peña Colorada, one of Mexico’s largest iron ore mines (a joint venture by ArcelorMittal and Ternium). Facing declining ore grades, Peña Colorada adopted Hexagon solutions to uncover and capture project value. A comparison of two Life of Mine (LOM) plans from 2012 and 2016 (before and after implementing Hexagon solutions) shows that between 2019 and 2023, Peña Colorada reduced actual waste by 26% (compared to 2012 LOM) and 19% (compared to 2016 LOM). LOM Plans are generated yearly, and each time, opportunities for reducing mining waste were identified, evaluated and implemented. The key driver was schedule optimization using Hexagon MinePlan Schedule Optimizer (MPSO). This reduction means less waste transported to disposal sites, resulting in fewer hauling equipment operating hours, lower fuel consumption, and reduced carbon emissions.

Feb 22, 2026

By Mehmet Ali Recai Önal, MAHMUT CAMALAN

Mineral liberation is one of the primary objectives in comminution circuits for the downstream separation of valuable minerals. Breaking minerals through their grain boundaries (grain-boundary breakage) enables mineral liberation in their natural grain size, removing the need for intensive grinding. This study aimed to evaluate if gaseous carbon dioxide, oxygen, or hydrogen can be used as grinding additives to promote the liberation of chromite grains by grain-boundary breakage. For this purpose, chromite ore particles in the −9.53 + 6.35 mm size fraction were pretreated by exposing them to carbon dioxide, oxygen, or hydrogen flow. Then, the untreated and pretreated samples were broken in a drop-weight tester under the same conditions. Finally, the graderecovery plots of chromite grains in the selected progeny size fractions and the overall progeny distributions were measured and compared. Pretreatment with carbon dioxide flow was found beneficial for grain-boundary breakage. It significantly enhanced the liberation of coarse chromite grains along with the overall progeny fineness. EPMAanalysis showed that the adsorption of carbon dioxide seems to reduce aluminum concentration at grain boundaries, which could be the reason for grain-boundary weakening. These results suggest that carbon dioxide can be used as a grinding additive, reducing the carbon footprint of the mining industry.

Oct 29, 2020

By S. Shankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant. Therefore, as part of the Respirable Dust Center's ongoing research, a three part study was envisaged: study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; study of the same in the Lake Lynn Laboratory Mine of the USBM with both airflow and walking by personnel causing re-entrainment; and mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory Mine are presented. Further, the results from the wind tunnel studies are compared with the results from in-mine studies conducted at the Lake Lynn Laboratory Mine of the USBM. Comparing the results from the two studies it was observed that increasing air velocity increased the rate of re-entrainment, but increased time of exposure decreased the airborne dust concentration. Compared to same size particles, a mixture of sizes created more airborne dust concentration when re-entrained. It was also observed that contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1995

By C. E. Jordan

Direct digestion of phosphate ores by the acid-alcohol method offers improved leaching selectivity for the exclusion of iron and aluminum in the product acid. The leaching kinetics of this process will have a major role in the eventual application of this technology. The Bureau of Mines investigated apatite dissolution to determine the reaction rate and mechanisms of the leaching kinetics. The dissolution kinetics were monitored on various sized fractions of pure apatite. The "shrinking-core" kinetics model was applied to the data to determine the rate controlling mechanisms. For each size fraction, the initial reaction rate was controlled by the dissolution reaction. After an hour the dissolution rate slowed indicating a diffusion controlled reaction caused by the formation of calcium sulfate hemi-hydrate coating on each particle. For complete dissolution of the apatite, the phosphate rock should be ground to near 10 µ m size.

Jan 1, 1993

By T. J. Batchler

"INTRODUCTION A variety of standing supports are being applied in underground coal mining operations to assist in providing stable mine entries. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Considerable research and development has been conducted by support manufacturers to develop standing support technologies for the mining industry. The National Institute for Occupational Safety and Health (NIOSH) researchers, with the cooperation of various support manufacturers, have developed a testing protocol that evaluates performance characteristics of these standing support systems.. Using this protocol, each of these support systems has gone through rigorous safety performance testing under controlled loading conditions in NIOSH’s Mine Roof Simulator (MRS). It is important to understand the unique performance characteristics of each type of standing support. This information allows mine operators to determine if the support system is compatible with the conditions in the mine and to compare each support system and determine if that support will provide equivalent or improved support capability. This paper provides a comprehensive summary of support performance to facilitate this objective. SUPPORT DESIGN CRITERIA AND THE GROUND REACTION CURVE Standing roof support systems are designed to prevent unplanned roof falls. The selection of the standing support is based on the interaction of the support with the surrounding rock mass, and its function is to assist the primary support system in maintaining the integrity of the immediate roof. The standing support works to control the immediate roof structure by resisting deformation that contribute to delamination of the bedded layers and displacements that lead to separation of the bolted zone from stable roof structures above the bolted horizon (Barczak, 2005). Standing supports should be installed early enough and develop sufficient capacity to bring deformation of the ground into equilibrium before a critical deformation is reached that leads to a detached block condition, at which point the standing support will be required to carry the entire dead weight of the detached rock mass to prevent a roof fall from occurring (Mucho, 1999). The ground reaction curve (GRC) can be used to assist in determining the compatibility and design requirements for a support system. It is important to understand the significance of the ground reaction relative to the support design requirements. The ultimate objective is to match the support behavior to the ground response and create equilibrium (stability) of the rock mass. This equilibrium is accomplished when the support loading intersects the ground reaction curve (Figure 1). Essentially, the ground reaction concept implies that the convergence in the mine entry is controlled by the magnitude of the support resistance. However, as a passive support, the standing support develops its loading through convergence. As such, the support needs to maintain its load capacity through the associated deformation of the ground and resulting entry convergence until the equilibrium condition is reached. This requirement causes factors such as the support stiffness, peak capacity, yielding characteristics, and stability to be fundamental to proper support design and application. NIOSH contributes to providing this understanding through full-scale performance testing of support products in the Mine Roof Simulator."

Jan 1, 2017

By M. I. Brittan

A technique has been developed that analyzes routine mill operating data to determine the key operating parameters responsible for gold losses to tails. These parameters represent the prime operating variables having a dominant effect on gold recovery. The technique quantifies these effects for the specific plant being analyzed, providing a tool to optimize recovery and costs and so enhance the mine?s cash flow. The quantitative relationships generated will be different for each ore and plant: every case is site-specific and has to be treated on its merits. Examples are provided to illustrate the considerable metallurgical and financial benefits which can be realized from optimization. The examples are taken from case studies of mills in four major gold mining districts of the world.

Jan 1, 2010

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

This paper is aimed at helping the mining industry to better understand the challenges posed by electromagnetic interference (EMI) and to promote electromagnetic compatibility (EMC) in underground coal mines. The paper begins with a review of EMI standards in other industries, then presents some representative examples of EMI instances that have occurred in the mining industry, followed by a literature review of published EMI research in mining and, finally, a discussion on mitigation strategies and practical considerations related to EMI in mining.

By C. Zhou, J. Srednicki

Electronic systems have been increasingly used in underground mines to improve mine safety. These electronic systems emit electromagnetic (EM) energy which can adversely impact the performance of other electronic systems nearby and thus should be characterized. Researchers at the National Institute for Occupational Safety and Health (NIOSH) characterized the magnetic fields emitted from devices that can potentially interfere with the performance of proximity detection systems (PDSs) and compared the emission levels of these devices to the susceptibility of PDSs. In this paper, we present our measurement results pertaining to this effort. Particularly, magnetic fields emitted from the different orientations of a powered air purifying respirator (PAPR) and two lite trackers are evaluated based on the RE101 protocol specified in the MIL-STD-461G standard. The results show that both devices emit strong magnetic fields which strongly depend on the orientation of the devices. At some frequencies, the maximum emission levels from the two devices exceed both the emission limit given in MIL-STD-461G and the maximum magnetic fields that a PDS can withstand without a failure. The results and findings in this paper can help the mining industry better understand electromagnetic interference (EMI) underground and provide critical scientific data that support mining-specific recommendations to address EMI-related challenges.

Feb 1, 2023

By Alessandro Boscaro, Daniele Martinelli, Cristina Gabriela Oñate Salazar, Daniele Peila, Carmine Todaro

"The wear phenomenon in TBM machines is not a simple issue, as many parameters are playing an important role on the consumption of the tools during a tunnel excavation. The action of the wear due to the contact with the soil can occur on the excavation tools, on the cutterhead, in the excavating chamber and on the screw conveyor. The test developed at the Laboratory “Tunnelling and Underground Space Center” of the Politecnico di Torino is aimed to reproduce the interaction between the tools and the excavated material, simulating the excavation conditions in terms of soil conditioning and water content. The test, which is not standardized, is studied to evaluate the wear in a global point of view. The present work starts by testing the influence of the use of chemical agents during the conditioning phase on the drop of the wear phenomenon, in terms of metal weight loss. 1. INTRODUCTION The wear phenomenon of the excavation tools used in TBM tunneling machines is playing recently a major role in the design stage of full-section tunnels in both soils and rocks. Concerning EPB excavation technology, the main issue regarding productivity is the wear of its components (Peila et al.,2012), which increases the so called dead time in the whole process. The friction generated between the components and the ground causes the consumption of the tools and other metallic components in contact with the ground, described as primary and secondary wear by Nielsen et al. (2006a). This leads to downtime, with risky and complicated maintenance operations (Peila and Schulkins, 2009), as occurred in recent tunneling works in Liguria (Italy). The study of this argument in granular soils is very delicate, as it encloses not only the properties of the excavation tools, but also the characteristics of the ground to be excavated (hardness, mineralogy composition, shape and dimension of the particles and moisture content). The penetration mechanism is based on the scraping of the ground, by mean of cutting tools, with its consequent consumption. Concerning the rocks, the excavation principle is characterized by crushing the rock mass matrix by applying high compressive stresses through cutting disks. In such a way, to avoid frequent downtimes and their consequent economic losses, it is very important to study this subject and therefore understand and forecast the durability of the components, in order to try to maximize the productivity of the machine by reducing the frequency of maintenance stoppings."

Jan 1, 2016