Search Documents

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method traditionally solves each mesh equation by an approximation during each iteration. Thus, it is interesting from both a theoretical and a computational viewpoint to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation that has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the solutions.

Jan 1, 1998

By A. Pomianowski

A spectrophotometric study of xanthate solutions alone and their mixtures with equimolar amounts of alkyl trimethyl ammonium bromide (CnTAB) has established the additivity of ultraviolet spectra (190 - 400 my) for potassium ethyl xanthate (KEtX) and C12TAB. No obvious effect of C12TAB addition on the decomposition rate of KEtX was observed. The kinetics of collector abstraction by copper, nickel and sphalerite powders were studied in 10-5 - 10-3M solutions of KEtX alone and in equimolar mixtures of KEtX and C12TAB. Presence of C12TAB caused a 2 - 3 fold increase in the amounts of xanthate (equivalent to many monolayers) abstracted by copper and, nickel powders but had no effect on the abstraction of xanthate by unactivated sphalerite. The adsorption of C12TAB itself from the mixed solutions was very low, at most ore monolayer only, and was not influenced by the nature of the solid powder used. The results are interpreted in terms of molecular associations and synergistic action of xanthates and quaternary amines.

Jan 1, 1963

By Peter G. Zambas

In planning an underground room and pillar mine, the selection of the shaft or portal location and the orientation of the main haulage arteries is of paramount importance, particularly in view of the high dependence of the cost of truck haulage on the proper definition of these parameters. In an effort to facilitate this selection a computer program was written which, by relating the truck characteristics to the areal configuration of the property or ore-body, derives the volume-weighted total fuel and time requirements for hauling ore from every panel within the property to a specified portal or shaft location through a predetermined gridwork of haulage drifts. By varying the size and orientation of the gridwork and the location of the portal or shaft access, an infinite number of configurations can be investigated. The results of this analysis can be plotted to indicate the optimum conditions.

Jan 1, 1971

By Ingemar Marklund

INTRODUCTION Today at LKAB, the primary mining method used is sublevel caving, independent of ore-body size, shape, dip, and geographical location. The mining of small ore bodies with relatively flat dip involves a lot of develop¬ment work, a large initial investment, big dilution, and large ore losses. In 1975 serious investigations into other possible methods, especially for those small ore bodies which do not lie in direct contact with other ore bodies, began. Different methods were studied and a number of in¬teresting ideas came from Russian mines. An analysis was made of one of the proposed methods, sublevel benching, in which mining is carried out from raises, and which uses the throw from the blast to place the broken ore. However, there were reservations about working in big open rooms at great depth, and doubts about the possibility of getting acceptable drilling results in an acceptable environment from raised platforms. Testing was therefore delayed for a time. However the investigations continued and in the fall of 1976, it was decided to try vein mining in a small ore body (Indian) (see Figs. 1 and 2). MINING RESULTS The results are now available from the mining of Indian and are as follows: Ore plan area 1200 m2 Level height 50 m Ore volume 60 000 m3 Ore tonnage 270 000 t Iron content 62% Dip 0.69 rad (40°) Ore thickness 14 m Ore compressive strength 26 MPa Ore C-factor (fracture density) 0.21 Hanging wall compressive strength 28 MPa Hanging wall C-factor 0.27 About 40 000 m of the holes were drilled by ring drills with an average productivity of 85 m/shift; loading of a round (2 rows, 750 m of hole) was usually accomplished in one shift. The total ore recovery was about 270 000 t with an average iron content of 59%, and three to four shifts were required per round (4700 t) to load. The principal of "throwing" the rock during blast¬ing worked well, and no ore remains on the footwall. ROCK CONTROL Before mining commenced at Indian, it was dis¬covered that the rock strength in its vicinity was rela¬tively poor. Since the ore is flatly dipping, and mining was to take place with open rooms, the strength of the hanging wall was of great importance. A supplementary program of exploration drilling was done during the fall of 1976 in order to assess fracture spacing and rock strength from the drill cores. Results showed that the strength of the hanging wall was low because of the many fractures. A decision was made to try cable bolting of the hanging wall by extending some of the ordinary blast¬holes. Cables (20 mm diam) were grouted in these larger holes and the rest of the hole was then utilized for ordinary loading (see Fig. 2). About 100 bolts altogether were installed and, to date, only small falls have occurred and the hanging wall is holding. Its exposed area is 2100 m2 DEVELOPMENT WORK On the 350-m level, four crosscuts (two per mining room), one longitudinal drift, and two elongated drifts (one per raise) for the raise climber were developed as shown in Fig. 1. Of the 230 m of drift, 60 m were in ore and the rest in waste. For mining room A alone, a total of 115 m of drift were needed with 30 m in ore. The drift dimensions were about 4.5 X 5.5 m. In the drifting on the 300-m level, two connecting drifts were driven from one existing transport drift forward to the respective raises. The total development was 93 m, all in waste (Fig. 1). The two raises having a length of 80 m each were driven at an angle of 0.68 rad (39°) from the hori¬zontal. They were driven along the footwall contact with a separation of 30 m and had an area of 10 m2. LONG-HOLE DRILLING The drilling of long holes with the ring drilling unit began in the fall of 1977 in raise A. The equipment consisted of an Alimak raise climber, equipped with a lower platform from which the charging was done.

Jan 1, 1982

By Rollin A. Slater

The bulk materials handling industry has served silently for years as the skeleton structure and often the central system of nerves and nourishment for the body of basic production industries. During the past two decades, this body has undergone substantial growth and mutation to meet the surging demands of our national economy for more and better products. The steel industry has been prominent in this phenomena and plants of the sixties are as unlike the second war vintage as our current crop of basketball players differ from their fathers. Steel has kept pace with spiralling demand by innovation which has resulted in new processes and improved designs which generally yield greater production from fewer units. The supporting industry of materials handling has likewise improved its techniques and currently has a new stronger generation of equipment to perform its necessary supporting function. It has been my fortunate experience to have been instrumental in the creative stages of several new steel mills which are currently in conceptual design or actual construction. Drawing upon exerpts from this experience, this paper will describe a basic approach to the selection and application of modern bulk materials handling systems to an entirely new steel plant. Specific details of past work are not available for publication, therefore, the plant described herein is a composite of ideas and will be the new plant of the Hypothetical Steel Corporation which will be located on the lower shores of the Great Lakes.

Jan 1, 1967

By W. L. Price

Since first introduced in the United States in 1964, rail mounted bucket wheel stacker-reclaimers have gained wide acceptance by users. The coal burning power plant group has adopted this new storage tool most quickly. The actual history is traced in this area in some detail. Installations in phosphate and steel mill ore storage and a listing of present users are included.

Jan 1, 1969

By R. Hendrickson

In the 1940's a top blown water-cooled oxygen lance was developed to inject oxygen into liquid iron. This process, the LD or BOF process technique, today is used in 65% of the world's steel production, and represents the largest oxygen market for temperature enhancement in steel and non-ferrous smelting applications. There are three major approaches to the use of oxygen in metallurgical processes: (1) general enrichment of the air supplied to burners or tuyeres, (2) under-flame enrichment or injection, and (3) the use of an auxiliary oxy-fuel burner as a heat source. With each of these techniques there are technical and economic trade-offs.

Jan 1, 1990

By M. L. Smith

SAG mill throughput is often a bottleneck in increasing metal productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility which is also relevant to the rock fragmentation that is achieved by blasting. The relation between the size distribution and fragility of the feed and of the mill's product and the critical size in a SAG mill is examined.

Jan 1, 1993

By H. J. Chen

In recent years, it has been recognized that the high horizontal stress is an important factor that contributes to a cutter roof. When the immediate roof is thinly bedded, the presence of a high horizontal stress may first cause failure on the bedding planes or weak planes, and then a cutter roof develops as the individual stratum crushes and buckles progressively layer by layer. In this study, the stress distributions in the bedding planes of the immediate roof are analyzed for an entry-pillar system in the multiple longwall panels by using the finite element method. Then the roof failure is analyzed based on the rock failure criterion and the stress distributions.

Jan 1, 1998

By S. S. Peng

A well designed mining plan is one which minimizes the cost and the mining induced problems and maximizes the recovery of the coal reserve. In order to minimize the negative effects on surface structures caused by ground subsidence process due to underground mining activities, two kinds of practices are commonly employed by the mine operators. One is the support techniques which leaves an area of coal un-mined or partially mined beneath the structure to be supported. The other is the protection techniques which protect the structure when it is subsiding with ground taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting techniques, the only currently available method in the U.S. is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However; The size of the support area designed by this method will be excessively large resulting in wasteful use of coal reserve when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for de-signing the support area. This method is based on a large amount of subsidence data collected throughout a number of major U.S. coal fields and the authors' experience with monitoring and protecting surface structures undermined by longwall panels. It considers the critical deformation in-dices that a structure can tolerate, and depth and height of underground extraction. The support area designed by this new method will not only assure the safety of the structure to be supported but also maximize the extraction of the coal reserve.

Jan 1, 1993

By Carl G. Consalus

The Kemmerer Coal Company's Sorensen Mine is located approximately 7 miles Southwest of the Town of Kemmerer, Lincoln County, Wyoming. The coal it produces is delivered via conveyor directly to Utah Power and Light's Naughton Steam Generating Plant. The Plant went on the line in the spring of 1963 and the Sorensen Mine has been producing coal since February of that year. In this period, approximately 2, 000, 000 tons of coal have been delivered to the Plant. Present Sorensen mining operations are being carried out in the upper seams of the Adaville Formation. The formation contains, in some places, up to 30 coal seams of varying quality and thickness. Thirteen seams are considered major and are given numbers; the rest are considered splits off of the major seams and are so named. The lowest seam stratigraphically is the No. 1, or Elkol seam. So far, it has not been committed to power production but is being held in- reserve. It is the thickest seam with 80-90 feet of coal as its average thickness. The other major seams vary from 10-50 feet thick, with most of the seams averaging 17-26 feet of thickness. Each major seam has been opened at least once' to obtain a true gross sample of the coal's performance in the Plant.

Jan 1, 1967

By A. Rai

"This paper provides an overview of the current use of auxiliary ventilation product and the challenges with limited air quantity in dead-end entry or working face. The PVC low frictional factor, low physical constraint and minimum leakage ventilation duct was development with ""made in US and used in US"". The PVC duct development covering operational and total cost of ownership with on-going success will be presented. This paper will discuss mine sites using new PVC vent duct underground and the results from operational and technical side making a difference. INTRODUCTION The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone’s, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods [3].Mining Method; Underhand cut and fill : The mine uses underhand cut and fill method which has 12’x12’ top cuts and several different size undercuts. The ore body is accessed off of a secondary development heading, utilizing a heading with a cross section of 14W x 14H or 15W x 16H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the type of drilling machine being used. An example of a typical topcut and associated undercut layout is shown in Figure 2. SECONDARY / AUXILIARY VENTILATION IN UNUNDERGROUND METAL MINES The auxiliary ventilation system provides the required air volumes at the face of dead-end developments and production workings, which in many cases may be considered as the primary method of assuring that the air quantity and quality standards in these working areas are satisfied. The Auxiliary fans and ducting systems are usually the primary means of delivering the required air volumes to the face of dead-end developments and production workings. Both centrifugal and axial-flow fans are used in underground auxiliary ventilation systems, usually electric powered. The internally direct driven axial-flow fans tend to be more popular because of their compactness and adaptability to staging. The most commonly used materials for ridged tubing are coated steel, alloyed steel, fiberglass and resin. Flexible (collapsible) ventilation tubing is also used and is usually made from neoprene-coated or nylon material. To add stiffness and reduce collapsibility these fabric ducts can be formed over a steel spring frame. A very important factor in the design of an auxiliary ventilation system is to minimize leakage and reduce the frictional pressure losses along the auxiliary ducting systems by minimizing their friction factors (K)."

Jan 1, 2015

By S. Komar Kawatra, J. J. Carlson

"It is widely known that steel made from iron ore pellets high in phosphorus is brittle. Removal of phosphorus from iron ores such as hematite has proven to be difficult. The majority of research on phosphorus removal from hematite ores has been focused on flotation. The purpose of this study was to assess phosphorus distribution under current operations at an existing hematite concentrator and determine how efficient the plant is at removing phosphorus. Objectives included: (1) Perform a phosphorus balance at an operating plant to assess phosphorus distribution under current operations; (2) Determine phosphorus removal efficiency of each separating unit and (3) Perform a quantitative liberation analysis to determine max phosphorus removal by physical means. Liberation was quantitatively determined using wet high intensity magnetic separation (WHIMS) to separate iron ore from liberated apatite (and other nonmagnetic compounds).It was observed that 61.2% of the total phosphorus entering Plant F was rejected during current operations. The desliming process was the most efficient step at removing phosphorus (45.1% P removed), whereas the flotation step was much less effective (16.1% P removed). Liberation analyses indicated that the deslime thickener may have been more efficient at removing phosphorus than the flotation circuit due to the greater abundance of liberated phosphorus in the deslime thickener feed. The scavenger returns stream was identified as having a high concentration of phosphorus and a possible point of phosphorus removal. However, liberation analyses indicated that only 32.4% of the total phosphorus in the stream was liberated. Grinding the scavenger returns to 80% passing 5.2 µm increased the amount of liberated phosphorus in the stream to 70.4%."

Jan 1, 2014

By Robert B. Scott

The Dents Run Demonstration Project near Morgantown, West Virginia, was a cooperative venture involving the U.S. Environmental Protection Agency (EPA), the Water Resources Division (WRD)(1) of the West Virginia Department of Natural Resources (DNR), and the Christopher Division of the Consolidation Coal Company (CONSOL). The object of this project was to demonstrate pollution control methods and to clean up a 37.8 sq km (14.6 sq mi) watershed severely polluted by coal mine drainage. A study entitled, "Water Infiltration Control to Achieve Mine Water Pollution Control" (EPA-R-2-73-142),(2) was conducted by the Cyrus Wm. Rico Division of NUS Corporation for the grantee to determine the feasibility of utilizing remedial techniques to improve the Dents Run water¬shed. This study showed that the Dents Run watershed was discharging as much as 6,870 kg/day (15,100 lb/day) of acid; 1620 kg/day (3,560 lb/day) of iron 17,250 kg/day (38,000 lb/day) of sulfates; and 29,500 kg/day (64,900 lb/day) of total dissolved solids into the Monongahela River near Morgantown, West Virginia. This pollution was caused by the combination of borehole pump discharges from active underground mines, runoff from abandoned strip mines, and runoff from refuse dumps.

Jan 1, 1977

By T. S. Spicer

Inflammability and crossing point apparatuses were used to study the influence of increasing amounts of such inerts as ash, fly-ash, pyrite, limestone and Portland cement with several pulverized bituminous coals. The results indicate that it requires large proportions of inerts to substantially suppress the ease of ignition.

Jan 1, 1962

By P. G. Corser

A gold and silver open-pit mine located in northwestern Chile contracted ACZ in 1991-92 to assess the stability of their spent ore pile and to determine the cause and magnitude of cyanide contamination associated with leaching operations. The mine is a conventional open-pit located at an elevation of approximately 4,800 meters (m.) (15,744 feet). A spent ore pile is located approximately 2,000 m. southwest of the mine and approximately 1,000 m. northeast of the active pad and plant facilities. The pile was constructed on a gentle northwest slope dipping 12 to 13 degrees. The pile is bordered by a small river to the northwest and by a larger river to the northeast. Both rivers eventually flow into Bolivia. Heap leaching and processing commenced at the mine in 1988. Since 1988, nearly 6.0 million tons of ore at an average grade of 1.96 grams/ton (0.07 ounces/ton) of gold and 52 grams/ton (1.83 ounces/ton) of silver have been treated by cyanide heap leach methods with zinc (Merrill Crowe) precipitation. In approximately three years of operation, the mine has yielded more than 225,000 ounces of gold and over 1.5 million ounces of silver. Currently ore is agglomerated and hauled to the leach pad by truck and is top loaded to produce a 5-meter lift height. Four contiguous reusable (on/off) leaching pads were constructed with an asphalt layer above a carefully compacted sub-base of High Density Polyethylene (HDPE) liner and screened fines. Leach solution of pH 10-11 containing 1.2 to 1.5 gram/liter of cyanide is applied to the heap at a rate of 10 liter/hour/square meter for a total active application period of 30 days. Leached (spent) ore is transferred to the spent ore pile located approximately 1,000 meters to the northeast. The pile currently contains approximately 6 million tons of spent ore. The pile liner, which has been constructed over a prepared sub-grade consists of three geosynthetic layers (geotextile/flexible membrane liner/geotextile). Long term objectives include washing the pile to recover an additional 3 to 4 percent gold and silver.

Jan 1, 1993

By C. Zhou, R. Jacksha

This paper reports measurement results for radio frequency (RF) propagation around 90° corners in tunnels and underground mines, for vertically, horizontally and longitudinally polarized signals. Measurements of signal power attenuation from a main entry into a crosscut were performed at four frequencies — 455, 915, 2450 and 5800 MHz — that are common to underground radio communication systems. From the measurement data, signal power loss was determined as a function of signal coupling from the main entry into the crosscut. The resultant power loss data show there are many factors that contribute to power attenuation from a main entry into a crosscut, including frequency, antenna polarization and crosssectional entry dimensions.

Jan 1, 2016

By A. M. McKim

6, 7.3 meter diameter autogenous mills at Wabush Mines are undergoing conversion from a radial configuration of pulp discharger to a curved design. Improved discharging efficiency has effectively lowered the pulp level in the mill. The low level operation enhances the grinding efficiency netting a 12% power reduction. Significant reductions to rate of wear has been a spin off benefit. The design incorporates features for holding the assembly solidly in place thus eliminating bolt hole damage and leakers. Preliminary work in one 11 meter mill at Hibbing Taconite did not indicate that all the same advantages were available in their process.

Jan 1, 1982

By J. D. Decker, T. E. Norman

Introduction Grinding is the reduction of ore and similar raw materials to particle sizes below the practical limits of commercial crushing ma¬chines. This size is about 36 in. (1 cm), in most cases, although some finer crushing machines are in regular use. The feed size to grinding machines may range upward to S in. in rod mills, and 12 in. or more in autogenous mills. The finest particle sizes produced in mineral processing operations result from grinding. Ordinary grinding of brittle materials is the result of impacting, rolling, and abrasion of heavy bodies, moving freely under the influ¬ence of gravity. These falling and rolling grinding bodies, which are usually of metal, must be much heavier and larger than the ore parti¬cles they break. This weight relationship is usually in excess of 100: 1. The sustained fall of the grinding bodies is obtained by placing them, together with the rock particles they grind, in a rotating drum or cylinder with horizontal axis, called a tumbling mill. The mill is nearly half full of grinding bodies and ore particles, which may be fed into one end and exit from the other through hollow trunnions which usually serve as the mill bearings. The mill lining must be thick to absorb wear and rough to prevent excessive slippage of the charge. The breakage of brittle rock or ore is accomplished by compression. The compression may be a rapid impact, from the fall and roll of a grinding ball, or it may result from the relatively slow and constrained motion as in a jaw crusher. Breakage by shear is a secondary result of the compressive motion. Ordinary rock has an extremely heterogenous structure with innumerable zones of weakness in which cracks, fractures, and breakages can form. When a rock is subjected to com¬pression it deforms. If the compressive force exceeds a certain critical value an incipient crack appears in the most fragile zones of weakness. This crack tip may first form on the particle surface or in its interior. When the first crack tip forms the compressive stresses immediately surrounding it flow to it, and this concentration of forces extends the crack and splits the rock. Other adjacent cracks may form during this extremely rapid process. Because of the nature of brittle particles, the work done in breaking them consists essentially of the work input required to compress them to the point at which the first crack tip forms. Breakage requires no appreciable additional energy input be¬yond that required for the deformation, since the stress energy already imported to the rock flows to the crack tip and extends it to breakage. Types of Tumbling Mills The general term tumbling mill includes the rod mill, ball mill, pebble mill, autogenous mill, and tube mill. It is of cylindrical or cylindro-conical shape and rotates about its horizontal axis. Rotational speed, liner type, and size and shape of tumbling media are selected to provide the desired operating conditions for the specific grinding application. Openings are provided through the mill ends for feed and discharge of the material being ground. A common feature of tumbling mills is the use of tumbling media

Jan 1, 1985

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.