Search Documents

By Serge Moalli

The Ashlu Creek Hydro-electric project, located north of Squamish, BC, at the confluence of Ashlu Creek and the Squamish River, comprises a 49 MW run-of-river project and features a 4.08 m diameter, 4.4 km power tunnel and a 128 m deep drop shaft. The Ashlu Creek Hydro-electric project is being developed by Innergex under Ashlu Creek Investments Limited. Site civil works are being completed by Ledcor CMI of Vancouver with tunnel construction by Frontier Kemper Constructors ULC under a lump sum design-build contract. Site works got underway in September 2006 with the construction of the tunnel portal and laydown area. These site works required rock slope stabilization over a 50 m rock slope to secure the laydown area as well as the construction of a tail track muck tipping station and structural wall to facilitate TBM excavation and spoil removal. Starter tunnel construction commenced in early 2007 and TBM tunneling started in the late spring of 2007 and is planned to continue until early 2009. The power tunnel is being excavated using a 1,200 kW Wirth open-type hard rock TBM dressed with 31?17' cutters. The TBM featured two fixed mounted rock bolt drills behind the finger shield: these were removed and replaced with jacklegs to improve access. A probe drill at the end of the main beam is also present. The geology along the 4.4 km power tunnel comprises very strong and generally massive granitic bedrock with rock strength greater than 225 MPa. A unique feature of the project is that no subsurface investigations have been completed for the tunnel however extensive bedrock outcrops are present along the Ashlu Creek valley. A historical quarry exists approximately mid-way along the tunnel alignment that has exposed good quality granitic bedrock. TBM tunneling to date has achieved advance rates of 10?20 m/day with a maximum of 23 m and has encountered all of the anticipated six major fault zones where the installation of various standard high capacity tunnel support was successful to facilitate TBM advance through these sections.

By Walter von der Linden

On April 14, 1975, Consolidation Coal Company began to operate a longwall face in their Shoemaker Mine using shield supports. This was the first time that shield supports were used in the United States (1) 1/. Shortly thereafter, Kaiser Steel Corporation started a shield longwall face at their York Canyon Mine (2). From October 1975 through May 1976, three more longwall faces were commissioned in mines located in south-western Pennsylvania and northern West Virginia. In June 1976, four installations had completed their first panel and two installations had completed the subsequent move to the second panel where coal production is now well under way. During this time (April 75 to June 76) the total number of shield support face operating months, including moving time, was 40 and the combined face advance was approx. 17, 000 feet (5200 m) with face lengths varying from 450 - 550 feet (137 - 168 m). While the shield support experience in the U.S. is still limited on the basis of time and mining parameters, the operating results of all faces have been very satisfactory. New record 24 hr production figures were set and - far more important - long term production figures could be sustained on an impressively high level even when taking face moving time into account. The purpose of this paper is to review the performance of shield type supports in the U.S. and to assess their value as longwall supports for U.S. underground mining conditions with regard to roof control, maintenance, operator convenience, safety and productivity.

Jan 1, 1976

By P. J. Doig

The LCLS project at SLAC will allow new insights into material properties, chemical reactions and biological processes. The project includes half a mile of new underground construction. Excavation in weathered rock is by NATM, using AM 50 roadheaders. Construction began in 2006 and is expected to be completed in 2008. This paper details the construction of the tunnels and cavern on the project.

Jan 1, 2008

By Jason Morrison

The Norwegian Lake Tap Method was successfully used to tap into the side of Lake Dorothy 36.5 m (120') below the lake surface. The lake tap allows water to flowinto an access tunnel from the lake lowering the water elevation below its natural out-fall. When the lake reaches a predetermined elevation below the outfall, a 1.5 m (60?) valve in the tunnel will be shut and discharge from Lake Dorothy will stop temporarily allowing construction of a dam located 2.9 km (1.8 miles) downstream at Bart Lake. The lake tap and tunnel were one phase of the $64 million Lake Dorothy Hydroelectric Project, owned and operated by Alaska Electric Light & Power Company (AEL&P), a private utility located in Juneau, AK. The Lake Dorothy portal site and tunnel are located approximately 25.7 km (16 miles) southeast of Juneau, AK, in the remote Tongass National Forest at an elevation of 701 m (2,300') above sea level in the mountains above the Taku Inlet. Thirty degree snow covered mountainsides and limited access by helicopter were just two of the many factors which challenged this unique project. The lake tap and tunnel development consisted of 250 m (820') of horizontal tun-nel, averaging 3.6 m x 3.6 m (12' × 12'), excavated using conventional drill and blast methods in highly competent Granodiorite and Tonalite rock, placement of one 3.9 m (13') long concrete plug, or bulkhead, located at the tunnel midpoint, and one 3 m (10') diameter lake tap into the side of Lake Dorothy. This paper will provide an analysis of the logistical and engineering challenges involved in the development of one of only a handful of lake taps in North America. AEL&P and contractor J. S. Redpath Corporation worked together to complete this critical project phase safely and on schedule, in a location accessible only by helicopter and plagued by constantly changing, harsh weather conditions. A strict schedule had to be maintained to ensure the timely operation of the downstream dam and power plant.

By Brian Fulcher

While tunneling in Europe has been a tradition for centuries, many companies and countries have embraced tunnel innovation with considerable vigor and creativity. Indeed, local needs and site conditions have provided the initiative for improved means, methods, materials and equipment to complete progressively more challenging projects. Many recently completed tunnels have expanded tunneling technology and contributed to the development of highly specialized and productive equipment ? such as the mixed-mode tunnel boring ma-chine (TBM) presently in operation at the SOCATOP A- [ ] 86 road tunnel and the high-pressure slurry TBMs for the Westerschelde Tunnel in the Netherlands and Hollandsas near Malmo, Sweden. This paper describes some of the key technologies employed by European tunnel builders and designers including the New Austrian Tunneling Method (NATM), advanced earth pressure-balanced (EPB) machines, pres-sure-faced (slurry) tunneling machines as well as ?hybrid? or mixed-mode TBMs. While these tunneling methods and equipment generally involve significant equipment investment, they may also involve highly trained, experienced and specialized tunneling and support crews as well as materials and tools specifically developed to supplement or complement tunneling performance. For example, mechanized pipe arch placement substantially improves ground support measures and NATM advance and on larger tunnel cross-sections.

Jan 1, 2007

By Martin Herrenknecht

Tunnel boring machines continue to develop to take on not only larger and larger diameters but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar has required innovative design approaches. A systems approach has been required to produce tunnelling machines that can not only safely excavate the tunnel but do so in an efficient, cost effective manner that stresses production and labor saving approaches. This paper will review the current design developments and present recent projects where these most recent principles have been applied.

Jan 1, 2008

By A. Arik

An accurate estimation of mining block grades continues to be a challenging task for ore reserve practitioners. Two of the factors that affect the accuracy of the estimates are the estimation method used and the variability of the mineralization in the deposit. The objectives of the study are twofold: Firstly, to see how different estimation methods perform on a given deposit. Secondly, to determine the impact of particular nature of the mineralization on the results. The comparison of several estimation methods for the prediction accuracy is performed using the conditional simulation results as the basis.

Jan 1, 2000

By G. W. Cutting

Interlocking material balances on complex mineral dressing plants greatly assist in metallurgical investigations: indeed, without such a balance, there is no firm basis upon which to base process performance evaluations. To achieve balances both qualitative and quantitative data must be rationalised in conjunction with the process flowsheet. WSL has developed a range of programs to evaluate interlocking material balances. However, to obtain maximum benefit from the balances, answers of direct value at the process level must be provided: WSL has developed also a range of programs for this purpose. Practical examples are given, which illustrate the benefits obtained from process balances.

Jan 1, 1979

By Edmund H. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence - the total absence of noise except for ones own breathing and scuffing of boots on the bottom. An underground mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working on the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur. But excessive noise is a health hazard. In recognition of this fact, our Congress included noise exposure as a part of the "Coal Mine Health and Safety Act of 1969". As Fig. 1 indicates, allowable noise exposure is established by specifying a time duration permitted at different noise levels. This is the well known "Walsh-Healey" criteria which governs noise exposure in many industries.

Jan 1, 1977

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations.

Jan 1, 2002

By S. Constantinides

Over the past 100 years we have witnessed a revolution in permanent magnetic materials. Prior to 1932 electrical machinery depended upon steels for both the soft and the permanent magnet structures. Because permanent magnet steels were easily demagnetized, motors, generators, loudspeakers and similar devices often used the interaction between two electromagnets. Motors and generators were mostly of the induction type, depending for function upon induced fields. The discovery of Alnico in 1931 and its rapid commercialization presaged an expansion of the industrial revolution and today, permanent magnet structures are widely utilized. [ ] DEVELOPMENT OF PERMANENT MAGNETS Act 1: Early Days of Permanent Magnets Alnico, which stands for aluminum, nickel and cobalt, is a family of alloys with similar structure and processing requirements. Additional elements, such as copper and titanium, are present in minor amounts to optimize magnetic properties. Alnico is known by many trade names around the world including Alcomax, Hycomax, Ticonal, Nipermag, Koerzit, Oerstit, Nialco, etc(1,2,3). In addition to the generic name ?alnico?, it is usually appended with a number representing the magnetic grade.

Jan 1, 2011

By B. K. Mishra

In order to maintain higher grinding efficiency in tumbling mills the mill interior and dynamics must be known. For this purpose, several different types of non-intrusive methods have been proposed and are being tried in the industry. We have made an effort to develop a diagnostic tool based on vibration signal. Here we discus results of our experiments pertaining to ball as well as SAG mill. In each case, a triaxial accelerometer was used to capture mechanical vibration generated due to the tumbling action of the charge. The vibration signal was transmitted to a remotely placed computer and the signals were analyzed by standard signal processing technique. In case of a ball mill (5m diameter), qualitative mill information could be obtained by correlating the vibration signal to feed rate and mill filling. An effort was also made to identify different motion characteristic of the charge by analyzing its vibration signal. In case of the SAG mill (10m diameter), liner wear was estimated by comparing the vibration signal emitting out of a freshly lined mill with that of a worn out mill.

Jan 1, 2011

By Joseph J. Diehl, Brian B. Khalighi

This paper discusses the Queens Water Tunnel, No. 3, Stage 2, being driven by a new Robbins High Performance (HP) Tunnel Boring Machine (TBM).The paper is divided into four sections. In the INTRODUCTION section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drive is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes, in the TBM OPERATION section, with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 1997

By Greg Wieland

Deep sewer tunnels are required to meet future growth demands of the City of Austin?s down-town redevelopment. The tunnel is 18,000 ft long and varies in finished diameter from 54 inches to 96 inches. The tunnel crosses under Austin?s Town Lake three times and there are four main work shaft sites. Geology, groundwater, foundations, downtown redevelopment, and an active, healthy community put significant constraints on the design. This paper discusses a major underground project for downtown Austin and discusses the risk considerations and the opportunities the design team took toward optimizing the project design for the construction phase.

Jan 1, 2008

By William W. Edgerton

The California Department of Transportation (Caltrans), the Contra Costa Transportation Authority (CCTA), and the Alameda County Congestion Management Agency (Alameda CMA) are involved in a unique partnership on the planning and design of the fourth bore of the Caldecott Tunnel, located on State Route 24 in Alameda and Contra Costa counties. The project will add a two-lane bore north of the existing three bores. The project will alleviate traffic congestion in the non-peak direction. This paper provides background on the existing facility, summarizes the need for the new fourth bore, describes the proposed improvements, sets forth the approach for project delivery, and lists some of the challenges that are expected during construction.

Jan 1, 2008

By Z. Yu

Low-rank/oxidized coals respond poorly to oil agglomeration. Emulsification of kerosene in the presence of surfactants dramatically reduces the size of the kerosene droplets. While this dramatically reduces the amount of oil that is required for efficient agglomeration (down to 0.25-0.5%), more importantly, the surfactants entirely change the electrokinetic properties of the oil droplets and thus the interaction between oil droplets and coal particles. Consequently, kerosene cationic emulsions can efficiently agglomerate oxidized coal particles. The agglomerates obtained in such a process can still be recovered by screening. Surfactants can affect fine coal filtration very profoundly when used to emulsify the oil which is utilized to agglomerate coal prior to its filtration. This sequence is much more logical than the use of flocculants - highly hydrophilic polymers - as filtration additives to aid dewatering of flotation concentrates. Although such polymers flocculate coal particles, they also render coal surfaces hydrophilic and make reduction of the cake moisture content difficult.

Jan 1, 2000

By M. M. Botz

There are currently more that 460 mines worldwide that utilize cyanide for gold and silver extraction. Despite this large number of cyanide-related mining operations, there have been no published accounts during the previous 25 years of the death of humans due to cyanide as a direct consequence of major mining-related environmental incidents. All published accounts of human deaths due to mining-related environmental incidents have been the result of physical inundation with tailings or waste rock materials. It appears that major mining-related environmental incidents have not been concentrated in any geographic location, are likely to occur regardless of the size of the mining company and do not occur more frequently with a specific type of mining activity. Several cyanide treatment and recovery technologies have been widely demonstrated to reliably control cyanide levels in mining solutions. With proper use of these technologies, tailings cyanide concentrations can be maintained at levels protective of wildlife while reducing the potential for adverse environmental incidents. The development of an international cyanide code of practice or management plan is recommended and should take into consideration the adoption of a weak-acid-dissociable (WAD) cyanide standard that maintains the levels entering a tailings impoundment below 50 mg/L.

Jan 1, 2001

The 18th annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held on Saturday, Dec. 2, 2000 at The Westin La Paloma in Tucson, AZ. The 2000 inductee, guest of honor and featured speaker at the banquet will be Ronald C. Cambre, chairman and chief executive officer of Newmont Mining. He will be honored for his role in positioning Newmont as an innovative and key player in the gold mining industry.

Jan 1, 2000

By Frank H. Madison

The percentage depletion deduction on Federal Income Tax Returns under the provisions of the 1939 Internal Revenue Code and of Sections 611 to Section 615, inclusive, of the revenue act of 1954, have created innumerable administrative difficulties, and a new interpretation of "gross income from the property" in that the Courts have expanded the ideas of what constitutes "gross income from the property" to a degree unheard of and unthought of prior to the enactment of these two codes. Originally, under the Revenue Acts of 1917, 1918, and 1920 depletion was allowable, based upon mine valuations as of March 1, 1913; if the mine was owned prior to March 1, 1913; upon cost, as of the date of acquisition if purchased subsequent to March 1, 1913; and upon a "discovery" basis if the mine was discovered after March 1, 1913, The "jab" for mine valuations as of March 1, 1913 and for discovery valuations and depletion was not as bad as it has been made out to be. Thousands of valuations and estimates of reserves were made and agreed upon between taxpayers and Internal Revenue Service engineers and as the years went on the answers have been found to be "reasonable." However, human nature being what it is each case was a battle of wits - of a sort - and many resulted in severe differences of opinion and litigation. As tax rates increased the situation was not bettered. I could talk for several hours on this phase of depletion but it is all past now andwould not give any real service or better understanding of the matter.

Jan 1, 1958

Traditional fine grinding mills in mineral processing relied on the use of steel medium for particle size reduction. The successful development of the Isa Mill(a horizontal stirred mill with 3000 litres of net chamber volume and 1120 kW rated motor power)adopted a novel product separator design that has led to a major revision of medium use in fine grinding. The Isa Mill separator has also successfully operated with a wide variety of medium types such as silica sands, river gravel, smelter slag, run-of-mine ore fractions and steel shots, with size ranges from 0.5 to 10 mm. A great flexibility of the Isa Mill operations has been achieved for processing a feed as coarse as 120 um to a product as fine as 5 µm. This paper discusses the performance of two inert grinding media used in the Isa Mills in Mount Isa Mines of Australia for processing galena and sphalerite bearing ores to below 10 microns. They are the copper reverberatory furnace slag (CRFS)and the heavy medium plant rejects (HMPR). A methodology was also demonstrated for comparing the medium performance and for scaling up the Isa Mills from a 1.5-litre laboratory batch mill to a full scale 3000-litre mill.

Jan 1, 2000