Search Documents

By Panshi Xie, Xicai Gao, Yi Luo, Youfu Zeng, Yongping Wu, Shenghu Luo

This research investigates roof deformation and failure characteristics, as well as mechanical interaction between the panels of the roof strata above two adjacent working faces in a steeply inclined coal seam. Physical modeling with photogrammetry measurement method has been employed in this investigation. The movement of roof strata and section pillar, as well as the stratum morphological characteristics, was quantitatively analyzed. Results show that the roof movement direction above the two panels has zoning characteristics, especially in the lower panel. Roof migration in the lower panel of the working face is larger than that in the upper panel. The roof to floor closure perpendicular to the seam direction is larger than the sliding along the seam. The maximum roof concave and convex bending occurred at the middle and upper parts of both panels; the roof bending in the upper panel mining area indicates a larger mining disturbance induced by lower panel mining. The void ratio contour of the lower panel is an asymmetrically arched shape, which is different from that of the upper panel area. The higher roof strata above the upper panel exhibit separation and breaking, whereas the lower roof exhibits compression due to mining in lower panel. The section pillar is compressed and slides slightly, which aggravates the mechanical interaction between the panels and increases the caving height of the roof over the lower panel and the periodic weighting intensity

By W. Missildine, J. K. Hrica, I. Benbourenane, T. J. Orr, J. L. Bellanca

Each year, haul truck accidents account for a large portion of mining injuries and fatalities. To better understand why these accidents continue to occur, researchers from the National Institute for Occupational Safety and Health (NIOSH) utilized a cognitive task analysis methodology to identify the user requirements of surface haul truck operators and assess differences in perceptions between operators, managers, health and safety professionals, trainers, and maintenance personnel. Additionally, researchers used the critical decision method to focus on better understanding the cognitive demands, decision-making, and problem solving during nonroutine incidents. The preliminary results of this study identify and explore themes within the broad categories of hazards, skills & expertise, and training and provide detailed accounts of nonroutine incidents such as near-misses, loss of control, and collisions. These accounts reveal insights into operator decision making and event progressions that can then be used to build more realistic training scenarios and address hidden hazards and root causes of these incidents. These results, along with potential solutions offered by study participants, can inform future research and help identify creative interventions that can be used by mine operators to address haul truck safety issues

Mar 2, 2022

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs.Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By George J. Hartman

The Fort Cady in situ borate-mining project involves recovering boron from a deposit more than 400 m (1,300 ft) below the surface. The resource recovery method is a new in situ mining technology that uses weak acid solution injected directly into the ore body. As the acid contacts the calcium-based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by submersible pumps. A series of chemical reactions and precipitations are performed that result in the production of calcium borate. The borate values are then recovered as a finely divided solid white powder. The refined product is sold under the trade name Cadycal 100. The Fort Cady in situ borate-mining project is located about halfway between Los Angeles, CA and Las Vegas, NV in the Mohave Desert.

Jan 1, 1996

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

By Xinghai Lei, Nan Wang, Xiangyang Jin, Yuqi Ren, Yang Li

The upward mining method, as an effective mining method, is widely employed in close-multiple coal seams to extend the service life of coal mines and improve the recovery rate of residual coal resources. However, the upward mining feasibility of the upper coal seam is related to the height of caved zone of interlayer strata after lower coal seam extraction. Therefore, it is extremely important to determine the height of the caved zone after the lower coal seam. The No. 9 coal seam (upper coal seam) and the No. 12- 1 coal seam (lower coal seam) in the Qianjiaying coal mine are selected as the research object. The characteristics of the interlayer strata structure field, fracture field, and subsidence field are studied using UDEC numerical modeling, in which the height of the caved zone is gotten after the No. 12- 1 coal seam extraction. Furthermore, the height of the caved zone is verified by onsite detection of GPR and BTVI. In the numerical modeling, the height of the caved zone is 19.6 m. And the height of caved zone is 14.7 m and 15.4–21.2 m, respectively, by using the onsite detection of GPR and BTVI. The heights of the caved zone onsite detection results are consistent with the numerical modeling result. The No. 9 coal seam is always located above the caved zone after the No. 12- 1 coal seam extraction. Consequently, the upward mining of the No. 9 coal seam is feasible.

Jun 28, 2023

By R. Pazhianur

Cathodic Protection using impressed current was employed to reduce the wear of the mill wall during ball mill grinding. Wear rates were determined from weight-loss measurements made on four, I-inch diameter, mild steel coupons installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH values of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 40-60010. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It is also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1996

By D. Shink

A small scale continuous flotation cell was designed and constructed at Noranda Technology Centre to develop a mobile testing flotation circuit located next to the production circuit. This mobile small scale flotation pilot plant can easily and economically be set up at any circuit in a mill and used to evaluate and predict plant performance against a given flotation condition. The main feature of the cell, beside the provisions of automatic pulp level and feed rate control, is to provide a reduced surface to volume ratio approaching to that of an industrial machine. This paper describes the basic design and the results of various testwork carried out to date including aeration, conditioning, reagents, recirculation, flotation gas, etc. are presented in comparison with the plant production results.

Jan 1, 1992

By VIVEK KUMAR HIMANSHU, M. P. Roy, P. K. Singh, A. K. Mishra, RAVI SHANKAR

Blasting with the aim to reduce oversize boulders in underground has many hurdles due to limited accessibilities and poor site conditions. Optimized drilling and blasting parameters can help to achieve this objective. The major challenges of the blast designers lie within deciding blast geometry, namely drill hole diameter, burden, and spacing. The general approaches covered worldwide to determine burden-spacing are based on various rules of thumb, which are based on previous experiences of blasts and the associated outcomes. However, many parameters influencing optimum burden-spacing to achieve desired fragment size are site specific. Sometimes drill geometry is decided based on associated blasting hazards rather than rock fragmentation. The Kuz–Ram model is a worldwide accepted rock fragmentation predictor. The parameters associated with this predictor also include burden-spacing for a blast. Back calculation of burden-spacing from the Kuz–Ram model can be used to achieve desired fragment size. This paper deals with burden-spacing determination by using an empirical approach for the underground stope ring blasting.

Jan 4, 2020

By Jamal Rostami, Ebrahim Farrokh

Selection of tunneling method, specially the use of shielded machines for application in deep rock tunnels can be heavily impacted by presence of ground convergence and squeezing conditions. Tunnel convergence is a function of ground conditions (i.e., rock mass behavior, groundwater, in-situ stresses), size of the opening, and TBM operational parameters. The case study of Ghomroud water conveyance tunnel project in Central Iran, which is under construction using a double shield TBM, is used to examine the effect of rock parameters on tunnel convergence and hence on the need for over excavation and shield lubrication to avoid problems with the shield getting stuck. Although it is impractical to perform a continuous assessment of rock mass conditions within the shield or in the lined tunnel, results of field observations and subsequent studies show that the amount of the tunnel convergence has direct correlation with the percentage of fines and large rock fragments in the muck and TBM thrust/torque/ROP. These relationships have been examined and will be presented in this paper.

Jan 1, 2007

The Anshan Iron and Steel Co. (AISC) broke its steelmaking design capacity in 1978, bringing its total production of steel products to 6.86 Mt. Located south of the industrial city of Shenyang, Liaoning Province, in northeastern China, it is by far China’s most important iron and steel complex, ranking twentieth among world centers. The complex represents a unique blend of old ecluipment and new ideas for increased production and improved products. Under a state plan, the Chinese hope to raise capacity to almost 15 Mt/a in the future. Originally started by the Japanese in the early 1920s, Anshan has had a rather turbulent 60-year history. It was disassembled by the Soviets after World War II, only to be reassembled by them in the 1950s. Production was also suppressed during the Cultural Revolution. Since the present-day organization, AISC, emerged, the center has experienced progressively improving conditions as well as increased production. Today, the center includes 10 blast furnaces, 24 open hearths, and two basic oxygen units, designed for 7 Mt/a ironmaking and 6.5 Mt/a steelmaking. In addition, it has six batteries of cokemaking facilities with combined 4.4-Mt/a capacity. Solid Iron Resources Anshan’s iron resources consist of a proven reserve base of over 7 Gt of 30~0 Fe, according to Kao Yang, president of the Anshan Iron Mining Co., a subsidiary of AI SC, Most of that, he continued, is amenable to surface mining. Five major mines located to the north and northeast of the city of Anshan are the principal iron ore producers. These mines trend in a somewhat circular manner and combined, represent an estimated 28.6 Ylt/a of ore capacity. In addition, some 2.2 Gt of magnesite, a necessary ingredient in steelmaking, are also part of the reserve base, according to Kao. Annual production is around .2 Mt/a of 47% magnesite, well over the steelmaking center’s annual requirements, Excess production is shipped to other steel-making centers. The largest of Anshau’s open-pit mines is the Chitashan operation with a design capacity of 8 Mt/a. Ore reserves here are well over a billion tons of 30% Fe. Earlier plans to expand production at this mine to 15 Mt/a, with the help of US Steel, have been temporarily shelved. The other mines in the district and their rated design capacity are: Kungchangling, 7 Mt/a; Donganshan, 6.4 Mt/a; Dakushan, 4.2 Mt/ti; and Yenchienshan, 3.0 Mt/a. The Kungchangling mine is the richest in terms of ore grade at 6076 Fe. Reserves are somewhat smaller at 100 Mt. The unit also operates a small shrinkage stoping operation. Ore grade at the other mines is usually 30-327. Fe. Llost mines operated at reduced capacity during 1979 owing to a natural gas shortage at the mills. The general

Jan 3, 1980

By L. Vinnett, J. Yianatos, S. Flores

"A numerical conditioning analysis for mineral recovery estimation was performed for industrial flotation plants, considering the copper (Cu), molybdenum (Mo) and iron (Fe) separability. A modified relative condition number, ?, was presented that allowed sensitivity analysis to be evaluated for the component recovery by means of an analytical formula. This closed form made it possible for the error propagation to be determined from feed, concentrate and tail grades with different orders of magnitude. The ? parameter can be evaluated using available grade data from the design criteria or historical mass balances, in which the variability is typically unknown. Reconciled data from different Cu/Mo concentrators were employed to evaluate the effect of small numerical disturbances in the grade data on the mineral recovery estimation. Higher error propagation was typically observed for Fe. The Mo minerals presented numerical problems, mainly in second cleaners and in the first cell of rougher banks. Lower condition numbers were observed for Cu due to the higher flotation rates.Mass-balance data reconciliation without redundancy was evaluated for a typical Cu/Mo flotation circuit using relative error minimization. Significant relative errors in the mineral recovery estimation were obtained with nonreconciled data in ill-conditioned problems. Negligible improvements in the mineral recovery estimation because of the data reconciliation with regard to the nonreconciled approach were obtained in well-conditioned problems. In addition, the improvements in mineral recovery estimation by using Cu, Mo and Fe in the data reconciliation were nonsignificant with respect to using only the best-conditioned component in well- and ill-conditioned problems.Despite the effort in data reconciliation and data repetition, poor performance may be obtained in ill-conditioned problems, which can deteriorate the flotation rate characterization. The error propagation has a negative impact on the mineral recovery of the first cell, which may significantly bias the flotation rate characterization of both valuable and nonvaluable elements.IntroductionMass balances have been extensively used in flotation processes to determine the mass flowrates (production) and mineral recovery (efficiency) of valuable minerals. Simple relationships for steadystate processes based on the feed, concentrate and tail grades can be obtained by taking a black-box approach. However, the calculation of concentrate flowrates from different components of the system, such as size fractions, chemical elements or minerals, does not satisfy the mass-conservation principle because of measurement errors (Smith and Ichiyen, 1973; Romagnoli and Sánchez, 2000). Mass-balance data reconciliation allows for obtaining a unique solution that satisfies the total and component mass balances, making small adjustments to the process data and taking advantage of the information redundancy (Narasimhan and Jordache, 2000). This methodology, which is based on a constrained weighted least-squares minimization, has proved to be robust when measurement errors are normally distributed, in the absence of gross errors.Commercial software has been developed to conduct massbalance data reconciliation in flotation processes, including MATBAL (Algosys, 2002), BILMAT (Algosys, 2013), JKMultibal (JKTech, 2013), BILCO (Caspeo, 2013) and HSC Chemistry (Outotec, 2013), which accomplish the reconciliation using known data accuracy in the optimization problem. The data accuracy can be obtained by sampling a stream n times in a run, known as repeats, each with independent chemical assays. Some unmeasured variables can be estimated using the measuring redundancy and sensor location. At present, grade and flow rate sensors may be incorporated in flotation to conduct real-time mass balances. However, a lack of sensor calibration and maintenance for suitable online measurements hinders the quality of the information. In"

Jan 1, 2016

By James Paone

Drillability of rocks by mechanical means is closely related to the physical properties of the respective rocks, Various approaches by previous investigators on rock drillability are presented, as well as recent techniques studied by the Bureau of Mines. The studies show drillability concepts based on (1) theoretical drilling equations derived from laboratory drilling experiments extended to field drilling results and on (2) a statistical method where multiple regression analysis is used to develop a prediction equation for drillability.

Jan 1, 1966

By E. H. Bentzen

The purpose of this paper is to explain the production of sand for glass manufacturing and the reasoning behind the sand specifications set by the glass industry. In order to discuss the production of glass sand, there is a need to understand what glass is and how it is made. Therefore this paper discusses glass, as well as sand beneficiation.

Jan 1, 1977

Recent U.S. mine disasters identified a need for improved training of miners in escape from mine fires and explosions. Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory (SRL) have designed fire-escape training software for use in a mine-safety training course. The software allows four trainees to work together in a virtual world via a computer network. Trainees responded favorably and showed a marked improvement in locating the proper evacuation routes on subsequent trials. In collaboration with the Pittsburgh Research Laboratory (PRL), a more elaborate fire evacuation scenario is being developed. Further study is needed to confirm that virtual training will translate to improved safety outcomes in the real world. Keywords: virtual reality (VR), safety, training, mining, mine fire evacuation

Jan 1, 2009

By K. Darcovich

The wettabilities of agglomerates made from coals of several different ranks were measured by the adhesion technique. Oil levels from 0 to 10% by weight were used. As was expected, it was found that higher-rank coals are more easily oil-wetted and that the surface properties of the agglomerates correlate with agglomeration recovery and ash removal data.

Jan 1, 1992

By Lynn Huntsman

INTRODUCTION The Sunnyside mines of Kaiser Steel Corp. are lo¬cated on the west flank of the Book Cliff Range, a tongue of the Wasatch mountain range in Utah. The mines are 193.12 air km (120 air miles) southeast of Salt Lake City and 40.23 km (25 miles) east of the town of Price. The area has a semiarid climate with an an¬nual rainfall of 304.8 to 381 mm (12 to 15 in.) and a temperature range of -23.3 to 32.2°C (-10 to 90°F). The base of the Book Cliff Range is approximately 1981 m (6500 ft) in elevation with some mountain peaks in excess of 3048 m (10,000 ft) (Fig. 1). The Sunnyside mines were opened in the late 1890s and have been operated continuously since that time. Kaiser Steel leased the No. 2 mine in 1942 and pur¬chased the entire property in 1950. There are three mines adjacent to one another, each with its separate access, ventilation, and haulage. The three mines en¬compass an area extending 12.87 km (8 miles) along the outcrop and dipping northeasterly 2.41 to 3.22 km (11/z to 2 miles) into the Book Cliffs. During 1975, only the No. I and No. 3 mines were operating to sup¬ply 908 184.7 t/a (1,000,000+ stpy) of clean coal to the Kaiser Steel mill at Fontana, CA. Sunnyside coal is blended with coal from the Kaiser Steel mine near Raton, NM, and with purchased coal from noncompany sources to form the mix for the coke ovens. At that time, Sunnyside operated three longwall units and five to seven continuous miner units. Typical production for that time came from one miner unit pillaring an area not conducive to longwall mining; one or two miner units on construction or modernization projects, and the remaining units used to develop future longwall panels. Longwall mining has been a part of the Sunnyside scene since 1961 when the first panel was set up in the lower Sunnyside seam of the No. 3 mine. Through 1975, 27 longwall panels were mined (Fig. 2). Of the more than 47 173 604 t (52,000,000 st) of clean coal that were taken from the property through 1975, 6 350 292.9 t (7,000,000 st) were mined by longwall methods. Coal was brought to the surface in 4.5-t (5-st) mine cars and crushed to -152.4 mm (-6 in.) before entering the preparation plant. Coarse coal is cleaned by Baum jigs and fine coal (-28 mesh) is cleaned in flotation cells. The coal is reduced to 50.8 x 0 mm (2 x 0 in.) and belted to an aboveground storage pile with a ca¬pacity of approximately 113 398.1 t (125,000 st). The coal is gravity fed through two 1.52-m (5-ft) diam culverts directly into railroad cars, which pass beneath the storage pile through an arched excavation. Eighty-four 90.7-t (100-st) cars make up a unit train which makes the round trip to the steel mill in four days. Additional trains are scheduled in as demands dictate. Loading rates in excess of 13 607.8 t/h (15,000 stph) have been attained. Geology The coal seams of this area are of Cretaceous age and are classed as a medium volatile bituminous coal. coal, with a sulfur content less than 1 % and 6 to (20-mile) zone of the Book Cliffs, and this area is owned or under lease by either Kaiser Steel or US Steel. Coal in adjacent areas is noncoking but an excellent steam coal, with a sulfur content of less than 1 % and 6 to 7% ash. Sunnyside coal contains 40% volatile, 53% carbon, less than 1 % sulfur, and 51/2 to 61/2 % ash after washing. There are two minable seams throughout most of the Sunnyside property known locally as the upper and lower Sunnyside. Separation between the seams varies from less than 300 mm (1 ft) near the southern boundary adjacent to the US Steel Columbia mine, to over 12.19 m (40 ft) in areas of the No. 3 mine in the center of the Sunnyside property. The upper seam varies in height from 1.2 to 1.98 m (4 to 61/2 ft) while the lower seam varies in height from 1.52 to 4.28 m (5 to 14 ft) in areas of No. I mine where the two seams apparently come together. The majority of early work was con¬centrated in the upper seam which has a stronger roof and a lower sulfur content. When Kaiser Steel began mining the No. 3 mine in the early 1950s, it mined in the lower seam beneath the old workings with conven¬tional and continuous mining equipment. Numerous bounces and pressure points created by unextracted pillars and barriers in the upper seam made this a low¬production, high-cost mine and brought about the ad¬vent of the first longwall system. The first unit, while small by today's standards, successfully mined panels that had been all but given up and saved the mine from closure. There were areas that could not even be mined by longwall because of the erratic extraction in the upper seam. The system was successful enough to allow operations to gain access to and develop virgin areas of the upper seam. Development of longwall mining in the No. 3 mine has been confined to the upper seam since late 1964. With the almost complete extraction afforded by the longwall system, it is felt the lower seam can be successfully worked in future years (Fig. 3). In most of No. 1 mine, only the lower seam (or lower seam and upper seam combined) is minable, except in the northwest portion where a rock split has again separated the seam into two 1.83 to 2.13-m (6 to 7-ft) thick beds. In this area, the upper seam or upper split is being mined. The separation between seams at the present workings in this area varies from 0.609 to 6.1 m (2 to 20 ft). It is hoped that most of the lower split can be mined using shield supports and/or what¬ever new technology is developed in the coming years. The coal seams in this area dip to the northeast at an average grade of 10%. The dip near the outcrop reaches 22% and gradually decreases downdip. Over¬burden ranges from a few meters at the outcrop to 762 m (2500 ft) over some of the deeper workings. In the next several years, some overburden will be in excess of 914 m (3000 ft) as the lower mine workings extend ever deeper under the Book Cliffs. To cope with the

Jan 1, 1982

By Yongsik Jeong, Kwangmin Kim

Most tailings storage facility (TSF) failures occur in active, upstream-type TSFs, often due to extreme and unexpected weather conditions—specifically, heavy rainfall and strong winds. This case study of a TSF in southern Arizona examines the use of the optimum safe beach distance (Doptimal, the optimum distance between the crest and decant pond) as a tool for monitoring geotechnical stability and reducing catastrophic failures. A digital model of the TSF was used to determine the critical beach distance (Dcritical) under normal weather conditions, and Doptimal was then determined by adding incremental distances to account for the effects of heavy rainfall (Drainfall) and strong winds (Dwind). To overcome accessibility issues, a drone was used to map the TSF geometry and create a digital model. This model served as the basis for conducting a coupled stress-seepage, finite-element (FEM) analysis with a safety factor of 2.0 to assess geotechnical stability (Dcritical). The safe beach distance increments were determined using the PMP (probable maximum precipitation) and possible maximum wind speed. Based on this analysis, the optimal safe beach distance at the study site was identified as 202.2 m. Since the current beach distance (371 m) exceeds this value, the TSF was considered to be stable and satisfied the design safety factor of 2.0. However, this distance should be reassessed periodically to account for changes in the TSF geometry and other conditions. Furthermore, it applies only TSFs that are well-managed and feature a smooth, non-undulating beach surface with a consistent slope.

By Michel Dagbert

In the exploitation of porphyry-type deposits, the quality of the ore is mostly defined according to its grade. Besides the simplest distinction, ore-waste, several grade categories may exist and they correspond to the different ways in which the ore is further processed. At the time of mining the selection of the different categories is done from extensive information available from blast holes. But planning has to be done before this information is available and it is necessary for the geologist to forecast, from exploration and development data alone, the possible outcome of the selection done later on a block, a level, or the whole deposit and ultimately predict the ore reserves and value of the deposit. A good statement of this problem has been presented at the 1976 AIME annual meeting by Williamson and Hueller (1976). They have shown that, if the cut-off values are directly applied to the estimated grade of blocks, a gross overestimation of the recovered tonnage of ore (14%) will occur. This problem, now termed "the vanishing tons problem" (DaVid, 1977) seems to be common in many open-pit operations and it has been explained several times (DaVid, 1972; Huijbregts, 1975). In order to solve it l.Jilliamson and Mueller proposed a solution based on compiling masses and masses of blast hole data available from mined-out portions of the deposit. They derived empirical correction factors which provide for every block, given its estimated grade, the expected tonnage and average -grade of each category of material within that block. The purpose of our work is to repeat the same exercise but ignoring the blast holes data i.e. we want to derive the correction factors from the only DOH data. Doing this, we are more in the real conditions where the valuation of the mine and are reserve analysis has to be made before production actually starts. Two possible ways to achieve this goal will be investigated and the emphasis will be on recently

Jan 1, 1977

By Charles B. Manula

This paper describes the development of a mathematical model for simulating the behavior of a longwall coal production system. The longwall simulator is a design simulator incorporating both deterministic and stochastic methods to calculate: (a) the size and density of support; (b) the cutting force, power requirements and haulage speed for the loader-shearer; (c) the conveyor size, speed and power requirements; and (d) delay generation at head and tail-gates and the longwall face.

Jan 1, 1978