Search Documents

By Xiaohong He, Qing Yu, Kaixiang Zhang, Rui Guo, Minghua Lin, Haoyu Miao

With the increasing depth of coal mining, the coal mine shaft traverses’ strata conditions become more and more complex. Shafts are often located in deep thick strata with unstable aquifers, and coal mining requires short-term rapid drainage of aquifers; the additional stress caused by aquifer water drainage is the direct cause of the shaft-lining failure. Over the years, many experts have conducted research on the shaft-lining damage caused by the consolidation and subsidence of the soil layer induced by the long-term drainage of the aquifer. On this basis, this paper conducts an in-depth study of the dynamic change of the pore water pressure of the aquifer in the short-term drainage and its influence on the response of shaft-lining strain and surface subsidence. The result shows that the Mandel effect of pore water pressure around the shaft-lining is obvious at the beginning of drainage, and the pore water pressure suddenly increases; the increase is independent of the drainage rate, which leads to the sudden increase of the shaft-lining strain value unrelated to the drainage rate. The result also shows that with the gradual dissipation of pore water pressure, the increase of shaft-lining strain is positively related to the drainage rate and negatively related to the drainage distance, and the variation trend of horizontal strain is greater than that of vertical strain, which appoints the main cause of shaft-lining damage.

Mar 16, 2023

By John A. Reeves

The unit-train concept of moving raw materials .is considered by many railroad men as the most signifigant contribution to reducing rail freight costs since the introduction of the diesel locomotive. The idea, which involves assigning railroad equipment to only one haul and keeping the equipment rolling results in the maximum utilization of equipment. For example before the unit train was plaged in servige on coal hauled to one of Mid. Continent's customers, about 900 cars and 9 locomotives were needed to move the coal requirements for this plant, compared with. 250 cars and 6 locomotives used by the present scheduling of unit trains. If the economics of unit-train movements are to be achieved, coal companies no longer can use railroad cars as small storage bins on wheels to accumulate their coal in trainload shipments, but, rather, must build large bins which incorporate facilities for the rapid loading of railroad cars in a minimum length of time. In this manner railroad equipment is operated at a high degree of efficiency 'with consequent dollar savings. After negotiations between Mid-Continent, the customers and the Railroad, it was decided a unit train loadout and storage facility at Carbondale was required in order to reduce the delivered price of coal to the customers and thereby contribute to the reduction in the cost of manufacturing steel. Carbondale was selected as the bin site location, because the cost of constructing a railroad to Redstone could not be justified for the tonnages anticipated.

Jan 1, 1969

By Verya Nasri, Heather M. Ivory, Kevin Clarke, Eric Cole

Development of the New York City Water Supply System The New York City water supply system serves a population of almost nine million, including residents in neighboring counties. Peak day demands on the system are currently running at about 70 m3/sec (about 1,600 mgd), which is significantly lower than in the 1990s. This trend of reducing demands over the past 25 years, which has been experienced in other major urban centers in the US, is mainly the result of conservation measures and increased cost consciousness on the part of water users. In the long term, demands are expected to once again follow an increasing trend with population growth, so that by the end of the planning horizon of these studies, the year2045, the peak day demand is expected to increase to about 85 m3/sec (2,000 mgd).The system is served largely by surface water sources, regulated by a system of 19reservoirs and three controlled lakes, which are connected to the City by a series of aqueducts, the longest of which is about 87 km (54 miles). The total storage in the sys-tem amounts to about 560 billion gallons, providing a system firm yield of about1300 mgd. The Delaware system provides about 50% of the City’s water, the Catskill about 40%, with the remaining 10% provided by the Croton. The system as a whole, which is shown on Figure 1, has been built up over the past 150 years, and is truly a marvel of engineering. The Catskill and Delaware aqueducts both discharge into Kensico Reservoir, which is a daily balancing reservoir located in Westchester County about 24 km(15 miles) north of the New York City line. The two aqueducts extend south for a further 14 miles to combine again at Hillview Reservoir in the Bronx, which provides hourly balancing storage for New York City system. The Croton aqueduct runs nearby as shown on Figure 2, but does not connect into the two reservoirs. From Hillview Reservoir the water is supplied to the city via three main distribution tunnels, known as City Tunnels 1, 2, and 3. City Tunnel No.1 was developed in the 1920s as part of the Catskill system. City Tunnel No. 2 followed in the 1960s as part of the Delaware system. City Tunnel No. 3 (CT3) is partly under construction and partly in operation, and is being implemented to permit the other distribution tunnels to be taken out of operation for the first time for inspection and maintenance. Presently CT3 is supplied with water from Hillview Reservoir via a large underground valve chamber, the Van

Jan 1, 2007

By M. F. Goodrich

The concept of using water-only cyclones as a clean coal scalping device preceding a heavy media cyclone circuit shows considerable promise, as it can considerably reduce the feed to the heavy media cyclone circuit. The system will not perform as well as a heavy media cyclone circuit alone, but the resultant loss in yield is small and may be negligible under some conditions. The concept of water-only cyclone scalping has previously been suggested by others. By reducing the amount of raw coal to be processed in the more expensive circuits overall capital and operating costs may be reduced. There are a few commercial plants with circuits operating on this concept. In the Warwick and Rowland plants water-only cyclones are used to scalp the feed to a heavy media vessel and Deister tables respectively while Amherst Coal Company's McGregor plant uses them to scalp the feed to a heavy media cyclone circuit. The system was evaluated on a technical basis, both from a theoretical viewpoint and by analysis of a computer simulation, in order to gain a fuller understanding of its usefulness and limitations.

Jan 1, 1977

By K. R. Gardner, P. B. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains ?1 ppm CN and 20 ppb Se; concentrations of other - major contaminants meet National Drinking Water Standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85% of the cyanide. Exploratory research shows that other bacteria removed up to 79% of the selenium from chemically oxidized, low- cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

By H. Sis, D. Dahlin, S. Chander, C. Summers

Bench-scale selective-flocculation tests were conducted on samples of Florida and Western phosphate process tailings. Physical, mineralogical, and surface characteristics were determined for both types of samples. The flocculation tests investigated dispersant and flocculant types and doses, pH, and slurry percent solids, while other parameters were held constant. Where selectivity was achieved, phosphate minerals remained dispersed, whereas silicate minerals flocculated and settled. In single-stage tests, flocculants having low to medium anionic character effectively upgraded products at moderately elevated pH. Multiple-stage tests, and tests in which flocculants of lower molecular weight were used as site-blockers, gave improved results.

Jan 1, 2002

By R. L. Virta

Ball Clay -- Four companies - H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Imerys Group (formerly Kentucky-Tennessee Clay Co.), Old Hickory Clay Co. and Unimin Corp. - mined ball clay in four states during 2010. Production, based on preliminary data, was 910 kt (1.11 million st) with an estimated value of $42.9 million. That was a 10-percent increase in tonnage from 831 kt (916 million st) with a value of $37.7 million that was produced in 2009. Tennessee was the leading producer state with 61 percent of domestic production. It was followed by Texas, Mississippi and Kentucky. About 70 percent of production was airfloat, 20 percent was crude and 10 percent was water-slurried.

Jan 1, 2011

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By Ronald J. Riberich

The Mineral Economics and Management Society (MEMS) held its fifth annual conference in Montreal, Quebec, Canada earlier this year. “The Minerals Industry: Responding to the Global Challenge” was the first MEMS conference to be held outside of the United States. About 125 mining- and minerals-related professionals attended. The MEMS program included six sessions and three distinguished speaker addresses. The session topics included: “Minerals in the Macro economy: Development in Demand,” “Trends in Global Metals Supply: The Producers’ Challenge,” “Global Environmental Issues: Policy Perspectives,” “Global Environmental Issues: Quantitative Analysis” and “Minerals in the CIS: Phoenix or Albatross?” A student session was also offered. It provided a competition for monetary awards for outstanding papers.

Jan 1, 1996

By Yifan Ding, Shemek Oginski, Patrick Finn

The Manhattan section of the New York Water Tunnel No. 3 constructed by the Schiavone/Shea/Frontier-Kemper Joint Venture is a $668 million project. The contract includes a tunnel drive of 8.85 km (29,045 feet), tunnel lining of 14.77 km (48,468 feet)and construction of nine shafts ranging in depth from 143 m (469 feet) to 169 m(555 feet). Construction methods for excavation of the shafts are presented including raise bore, ground freezing, soil excavation, blasting, slashing, muck handling, rock support and shaft final concrete lining.

Jan 1, 2007

By Jim Rozek, Robert A. Gee

The Epping to Chatswood Rail Line project is the largest publicly funded infrastructure project in New South Wales. Construction commenced in November2002 with opening scheduled for 2008. The work includes 13 route km of twin TBM driven 7.2 m diameter lined running tunnel, three cross-overs and three new underground stations. The new stations have platform caverns of 20m span with similarly proportioned concourse caverns alongside. The ground is bedded sand stone and shale with high horizontal stresses. Predicted stress-relief induced ground movements during staged excavation led to innovative use of rock anchors for permanent support.

Jan 1, 2005

By W. F. Riggs

1 Flotation Analogy To explain flotation in simpler terms the following analogy will be used. A factory (the flotation cell) manufactures a product (collector coated mineral). The product (collector coated mineral) is transported to market (the launder). A truck (the frother) is used to transport the product (collector coated mineral) to the market (the launder). The truck (the frother) transports the product over a road (the froth bed). The truck (the frother) and product (collector coated mineral) are supported by tires (the air). 2 Assumptions This operating philosophy assumes that the correct collector dosage is present along with the correct particle size distribution, pH conditions, etc. and that the minimum required frother dosage is correct. 3 Collector Addition The collector addition as used at a flotation plant is based on dosage rate as determined by the amount of mineral value entering the concentrator. Collector is normally added at two points in the concentrator: The primary flotation circuit and staged addition in the rougher scavenger circuit. Surveys have shown that the staged collector addition provides an increase in the kinetics and increases the recovery of the valued mineral in the rougher scavenger circuit. 4 Frother 4.1 Frother Dosage As explained in the above analogy, frother can be likened to the truck that transports the product (collector coated mineral) to market (the launder). Just as you would not use a truck rated at 15 tonnes to transport a 20 tonne load, you cannot expect to transport coarse minerals to the launder when there is insufficient frother present. Frother dosage must always be at, or above the minimum target. If less frother than the required minimum is used, then coarse mineral particles will not be supported and transported to launder where the mineral is recovered. To the naked eye the froth characteristics, even when insufficient frother is used, will appear to be correct. You cannot see the coarse particles that are not being recovered in the froth. (See Section 4.2 below for an explanation of why this occurs.)

Jan 1, 2006

By Steve Kral

Led by a surge in coal production and prices in recent years, Colorado’s mining industry is taking part in the same revival as others states and the world. Not too many years ago, the state’s industry was languishing in the same doldrums as the rest of the mining world. Ironic for a state whose history was based on mining. Now, however, Colorado’s mining can boast increased production in all commodities produced, along with prices that allowed companies to expand, increase work forces and post improved shareholder value. So there was a lot of optimism at the Colorado Mining Association’s (CMA) 107th National Western Mining Conference in February. The conference, held in Denver, attracted more than 500 attendees and 39 exhibitors. The theme was Colorado Mines the World.

Jan 1, 2005

By T. J. Lynch

A new class of polymeric dispersants for industrial minerals has been synthesized and evaluated. Currently available dispersants give initial low viscosities at high mineral loadings, however slurry viscosities can rapidly double or triple on standing over the first several days. The new dispersants give low initial viscosities that are more stable and maintain a lower viscosity for at least one month. The new dispersants are made possible by controlling the polymer molecular weight distributions during their manufacture such that essentially all of the dispersant is adsorbed onto the mineral surface, preventing depletion flocculation.

Jan 1, 2012

By M. L. Mellish

The year 1988 unexpectedly turned out to be a good year for the US coal industry. In fact, it was a third consecutive year of record coal production. Accord¬ing to preliminary Energy Information Administration data for 1988, domestic coal consumption went up 5%, or 41 Mt (45 million st), from 1987. Coal exports were up by a surprising 13.6 Mt (15 million st). In 1988, 22.7 Mt (25 million st) of coal were drawn from stockpiles for consumption. Even so, US coal production increased to 862 Mt (950 million st). That was up 28 Mt (31 million st) from 1987. While coal consumption, exports, and production were up, delivered prices for steam coal continued to slide during the year. Metallurgical coal prices, however, firmed up and showed a moderate increase. This reflected tight metallurgical coal markets at home and abroad. Coal consumption US coal consumption reached 800 Mt (882 million st), compared with 759 Mt (837 million st) in 1987. Increased metallurgical coal consumption was one factor. Most of the rise in coal consumption, however, was due to unexpectedly high electricity demand. Unseasonably hot summer weather al lowed added coal-fired electric generation to supplement the drought-related reduction in hydro-electric power supply. Electric utilities consumed 687 Mt (757 million st) of coal in 1988, 35.4 Mt (39 million st) more than in 1987. Coal-fired power plants remained the primary source of US electricity generation, providing 57% of the total in 1988. Coal consumption at coke plants increased 13%, to 38 Mt (42 million st), from the level consumed in 1987. This increase reflects the recent recovery in the iron and steel industry. Metallurgical coal consumption in 1988 could have been greater. But US coke plants reportedly reached their maximum practical production capacity. As a result, net US coke imports amounted to 1.45 Mt (1.6 million st). Despite increased industrial activities, steam coal consumption by industrial plants was up only slightly from the 1987 level, amounting to 69 Mt (76 million st) in 1988. Residential and commercial coal consumption remained virtually unchanged at 6.4 Mt (7 million st). Coal exports and imports US coal exports rebounded in 1988, reaching 86 Mt (95 million st). It was the highest level of annual US coal exports since 1982, when they reached 96 Mt (106 million st). An unusual set of factors led to an opening for US coal exporters in 1988: • a high level of industrial production in Japan and the European Economic Community, • supply disruptions due to labor problems at coal mines in Poland and Australia, • a drought-related reduction in hydro-electric power generation in Canada, requiring increased coal-fired generation, • China's problems in meeting its export commitments, and • a fall in the value of the US dollar. US metallurgical coal exports in 1988 amounted to 56 Mt (62 million st), 9.1 Mt (10 million st) more than the 1987 level. Europe, Japan, and Canada were the principal importers of US metallurgical coal in 1988. European countries, in particu¬lar, increased their take by one-third of US metallurgical coal. The labor problems in Poland and Australia contributed to these higher levels of imports. So did increases in pig iron production of 8% in Japan and 9% in the European Economic Community. US steam coal exports - including bituminous, anthracite, and lignite-increase to 30 Mt (33 million st). This was up from 25.4 Mt (28 million st) in 1987 Contributing to this overall rise were 1.8-Mt (2-million st) increase in shipments to Canada and a 2.7-Mt (3-million st) increase to Europe. Unaffected by the somewhat tighter world coal market, US coal imports showed a slight increase to 1.8 Mt (million st) in 1988. Colombia continue to be the leading exporter to the United States, followed by Canada and Venezuela. Venezuela's entry into the US market is a relatively recent one, having made its first significant shipment in the fourth quarter of 1987.

Jan 1, 1989

By N. A. Abdel-Khalek

The amenability of carbonate separation from a sedimentary phosphate ore using a bioflotation process was studied. Two types of bacteria were chosen for this study. The experiments were performed using oleic acid as collector. The flotation experiments were carried out using statistical designs for optimizing the main operating parameters. A concentrate containing 0.78% MgO and 30.15% P2O5 with a recovery of 92.31% was obtained from a feed containing about 2.45% MgO and 27% P2O5. These specifications could not be obtained using conventional flotation experiments under similar conditions in the absence of bacteria. Measurements of zeta potential, adsorption of bacteria and collector, as well as froth power, were performed to explain the role of microorganisms in the surface modification of both dolomite and phosphate and in their interaction with the collector.

Jan 1, 2009

By Richard F. Flanagan, Robert H. Marshall

The Republic of Singapore’s Public Utilities Board is implementing the Deep Tunnel Sewerage System Project. The project’s deep tunnel component, 48 km of deep, large diameter sewer tunnels has been successfully completed (the works are in the defects liability period). Six International Design/Build tunnel contracts utilized eight Earth Pressure Balance TBMs ranging up to 7.23 m in diameter to deal with varied ground types ranging from deep soft clays to fresh granite. Numerous access/workshafts were constructed and using various support systems. This paper provides an assessment/overview of the tunnel contracts, tunnel excavation methods and equipment, and the shaft systems. Suggested enhancements to similar future projects are provided.

Jan 1, 2007

By Leonel Lopez

Throughout Mexican history, mining has been an important, traditional activity. Before the "Discovery of America," native miners worked a variety of deposits throughout the country, including Mixtec gold and gem mines in Oaxaca State and Aztec gold, silver and copper from mines in Michoacán. The 500th anniversary of Mining in Mexico after the "Discovery of America" was initiated by the Mexican mining sector on April 15, 1991. As early as 1548, when the Guanajuato mining district was discovered, Mexico had become a leading world producer of precious metals. Since then, Mexican mineral production has developed in cycles, responding to changing technological, economic and political conditions. During the 20th century, Mexican mine output reached its peak in the decades of the 1930s and 1940s, when it was producing about 40% of the world's silver, 15% of its lead, 10% of its zinc, 4% of its copper and 3.5% of its gold. In 1990, by way of contrast, these percentages of world output stood at 13.5% for silver, 4.7% for lead, 4.1% for zinc, 3.2% for copper, and 0.43% for gold. The lowest production levels were recorded during the 1960s and 1970s, when Mexicanization of the industry and increasing state controls weakened mineral economics to a point that mineral exploration budgets were sharply reduced or eliminated, along with the industry's future. Only the noble old mining districts continued to supply production, with occasional eruptions of "bonanzas" and new extensions in established mining districts.

Jan 1, 1994

By Richard Weinstein, Richard Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Because of the environmentally friendly nature of dry jig plants, installation permits are often measured in days, not months. There has also been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But air jigging is not right for every application. There are limitations due to particle size, particle shape, moisture and near gravity content. This article explores the evolution of dry jigging. It reviews parameters important for determining the suitability of dry jigging. It also compares historical performance data as measured by imperfection, against results from modern dry jigging technology. The article also presents data from modern dry jig installations.

Jan 1, 2007

By M. H. Basiri

The application of aluminum matrix composites, due to their unique properties, is significantly growing in the variety of industries such as aerospace and automobile. In comparison to other light metals, such as magnesium and titanium, aluminum is lower in price. These are the advantages that this metal dominates the others. In this research, first by applying the lost foam casting method, the SiCp/A356 composite was cast in the bottom and side gate conditions with 690°C and volume fraction of 10%. Furthermore, the effects of reinforcement particles (60 µm, 75 µm) were examined. The results present the particles distribution in the side gate methods is more homogeneous than the bottom gate casting method. Also, by increasing the particles sizes, the fading rate in the side gate are reduced from 22% to 19%, as well as from 26.4% to 25.4% in the bottom gate. Key words: Carbide-Silicone Particle, Gating System, Composite Micro-Structure, Foam Casting

Feb 27, 2013