Search Documents

By D. D. Banerjee, S. K. Kawatra, T. C. Eisele

A high calcium fluidized-bed combustor ash was shown to be an effective binder for iron ore pellets at dosages of 1 % to 2% of the magnetite concentrate weight. Magnetite pellets that were between 1.1 and 12.7 mm (7/16 and 1/2 in.) in diameter were produced with dry crushing strengths greater than 22.3 N (5.0 lb-force) per pellet, which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. The addition of calcium chloride at a rate of 0.1 % to 0.2 % of the total powder weight increased the strength of the dried pellets by as much as 22 % compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1999

By John Ralston, Gayle E. Morris, Daniel Fornasiero

The interaction of talc with carboxymethyl cellulose, a polymeric depressant currently used in the mining industry, was investigated. adsorption isotherms, infrared spectoscopy and microflotation studies were performed to determine the surface properties of the depressant at the talc-water interface. Solution conditions were varied in ionic strength, pH and the presence of magnesium ions. The adsorption of the anionic polyelectrolyte, carboxymethyl cellulose onto the talc surface was greatly influenced by the solution ionic strength and pH. Limited adsorption, and therefore depression, occurred at high and low ionic strength. Adsorption, and thus talc depression, improved greatly with either increased ionic strength or reduced pH. With the addition of magnesium ions, talc depression was shown to improve considerably. The improved depression is likely to be the result of the formation of a magnesium ion-carboxyl complex.

Jan 1, 1995

By Yongping Hu, Dianchen Cai, Congya Zhang

China is a rich in stromite mineral resource. Unfortunately, the resource is very difficult to separate by using conventional flotation method because stromite and gangue minerals are very fine disseminated, the average size of them is about 10 µm or below, and the content of clay minerals such as illite is 19% or even more. In this paper, the aggregation floatation behavior of ultrafine (-10 µm) stromite, illite, ablbite and quartz using anion collector were studied. The result show that, Oxidized paraffin (O.P) is a good collector and has better selectivity for stromite particles flotation. The salted sodium silicate depressed illite gangues minerals effectively. The separation of mineral mixtures was carried on successfully at one stage flotation by the technique. The mechanism of O.P. and salted sodium silicate were studied and discussed by using IR and Zeta- potential measurements.

Jan 1, 1995

"In the mining industry, high-level commitments to adopt sustainability have been made at the corporate levels of mining companies, but there continue to be problems when attempts are made to adopt these high-level sustainability aspirations and translate them into appropriate targets and methods at the more-specific operational level. The integration of sustainability principles into day-to-day minerals processing operational decision-making processes has unique challenges that are not addressed adequately by current tools and methodologies. A proposed methodology to achieve integration of sustainability at the operational level will direct the systematic and rigorous identification and characterisation of sustainability issues in an operation. The methodology allows different approach strategies for assessment, comprehensive accounting of sustainability indicators and has the ability to identify sustainability issues which may have significant business implications that cannot be identified using traditional analysis processes."

Jan 1, 2011

By S. K. Kawatra

Various types of mathematical descriptions of the flotation process are used in the design of a full scale flotation circuit. Mechanistic descriptions developed under controlled laboratory conditions establish theoretical residence time requirements. Empirical models, describing flotation performance as a function of full scale operating variables, are established from one flotation system and applied to another hypothetical system. Problems of design by mechanistic modeling, such as scale up factors, can be alleviated if the model is developed from a full scale flotation circuit. However, the numerous uncontrollable variables encountered in a full scale operation would preclude the practical application of such a model. Incorporating empirical relations into the full scale mechanistic model will facilitate its effective use as a guide for flotation circuit design. A semi-empirical model has been developed that promises to offer a more effective means of flotation circuit design.

Jan 1, 1982

By P. Mousset-Jones, F. Calizaya

Currently, a 4.3 km long drift is being developed on the 3440 level in the Lower Kalamazoo project at the San Manuel Mine, Magma Copper Company, AZ. The drift, located at 1050 m below surface, is being constructed using a 4.6 m diameter tunnel boring machine (TBM). The drift is ventilated by a forcing type auxiliary ventilation system. At the face, to mitigate the impact on the work environment of the TBM, the system is equipped with dust extraction and refrigeration systems. Recently, to evaluate the ventilation conditions in the drift, a continuous monitoring system has been installed. The system can be used to measure the air velocity, barometric pressure, relative humidity and air and rock temperatures. This study describes the capabilities and limitations of this system, and presents a summary of the results.

Jan 1, 1995

By R. Gong, R. Bhaskar

The development of a three-dimensional mathematical model for evaluating airflow fields at a continuous miner face is described. The model utilizes three-dimensional incompressible flow, mass continuity, and momentum (Navier-Stokes) equations to predict the airflow velocity at the face. Obstacles and equipment in the face area are modeled using appropriate boundary conditions. Parameters such as flow velocity and face dimensions can be modified and evaluated for various schemes, such as exhausting and blowing ventilation, using either brattice or tubing. A model such as the one described, with additions for local effects, can be used to evaluate novel face ventilation ideas before initiating expensive full-scale tests or field studies. The model described is a step in the direction of advanced predictor models.

Jan 1, 1993

By Donald P. Spitzer, Peter V. Avotins

The flow properties of thickener underflow slurries can be characterized by their rheological parameters. Most of these slurries exhibit Bingham plastic behavior, characterized by a yield stress, to, and a Bingham viscosity, nB. Red mud is generated as a leach residue in the Bayer process. The use of new Bayer process flocculants which contain hydroxamate functional groups leads to muds which are qua1itatively considerably more fluid than muds generated with conventional polyacrylates or acrylatefamide copolymers. A variety of rheological tests confirm lower yield stresses and less extended floc structures with the new flocculants, at the same solids levels. Conversely, under given viscosity restraints, the new polymers make it possible to operate at higher solids levels, which offers major benefits in processing red muds.

Jan 1, 1992

By A. A. Kornyshev, M. Burstein, S. T. Hall

The surface "roughness" of mineral particles has long been known to influence the fundamental process of particle-bubble attachment and other subprocesses in froth flotation. The physical nature of the surface of fine mineral particles can be analysed by determining their fractal geometry. A number of techniques are available to measure the fractal properties of mineral particles, these include gas adsorption, mercury porosimetry, neutron or X- ray scattering and image analysis. From the resultant Richardson plots or their Fourier-space analogs, the fractal dimension of flotation feed and product samples can be determined. Textural characteristics of particles have an influence on the stability of 3-phase flotation froths and the selectivity of recovery in the froth. Decrease of the equilibrium froth height for particles of higher fractal dimensions was experimentally established. The induction time of quartz particles of different fractal geometry has also been studied.

Jan 1, 1995

By William Mark Hart

Newmont Mining's executive management launched an initiative in 1999 that was designed to engage the entire workforce in a continuous effort to systematically drive inefficiency out of the corporation. Built on a foundation of teams and teamwork, Gold Medal Performance (GMP) has had a significant and positive impact on the reduction of costs. At the same time, it has increased productivity, improved cash flow, and helped Newmont to further enhance health and safety programs. Currently, more than a hundred teams are working on improving line-balancing production and external communications at all levels of the corporation. The training and rigorous set of tools avail- able to and used by these teams were designed to help them improve communications, identify inefficiencies and their financial impact, develop and implement solutions, and finally, to measure the results of the process enhancement. GMP harnesses the energy, creativity, and productivity of the entire workforce.

Jan 1, 2001

By J. A. Brierley, Arpad E. Torma, Victor C. Storhok, C. L. Brierley, Batric Pesic

Chemical and electrochemical studies were performed during bioleaching of cobaltite concentrate with Thiobacillus ferrooxidans. The two principal minerals present in the concentrate were pyrite and cobaltite (CoAsS). During chemical studies, the effect of pH on dissolution rates was examined under uncontrolled and pH-controlled conditions. It was found that in the pH range 1.5-3.0 there was no pH effect if the initial pH was not controlled (maintained). When the initial pH was controlled, the leaching of Co, As, and Fe depended strongly on pH. Electrochemical studies were performed by using cyclic voltammetry and constant potential techniques. A sequential reaction mechanism was proposed for dissolution of cobaltite.

Jan 1, 1993

By M. Polat, S. Chander

Many models have been suggested in the past to obtain a satisfactory fit to flotation data. Of these, first-order kinetics models with a distribution of flotation rate constants are most common. A serious limitation of these models is that type of the distribution must be pre-supposed. Methods to overcome this limitation are discussed and a procedure is suggested for estimating the 'actual' distribution of flotation rate constants. It is demonstrated that the classical first-order model fits the data well when applied to coal flotation in narrow size-specific gravity intervals. When applied to material which is fractionated on the basis of size alone, the use of three parameter models, which were modified from their two parameter analogs such as rectangular, sinusoidal, and triangular, gave most reliable results.

Jan 1, 1995

By Thomas J. Martin, James W. Martin, Paul F. Martin

The conveyor belt is the basic building block of a broad range of material handling applications in modern mining systems. The mining plans and site conditions dictate basic system requirements but this is only a part of total design evaluation. The total system in the typical mining situation can encompass all the activities from the excavators at the mining face to the processing plant, site loadout facilities and/or a power plant. The number of alternative configurations which must be evaluated including subsystems and components is limited only by analytical time and creativity. The constraints and issues which must be addressed continue to expand, driven by reliability, environmental impact and cost competitiveness. All of the system requirements must be translated into specifications for costing, final design and construction.

Jan 1, 1993

One of the core tenets of Sustainable Development is transparency and information sharing, i.e., government and corporate reporting. Governments report on issues within their sphere of responsibility to the degree that their constituents demand that they do so. Firms undertake reporting for two reasons: they are required to do so by law, and doing so makes good business sense. In recent years, stakeholders have come to see themselves as having a right to information about government actions and business operations that have the potential to affect their lives, health, community and environment. As a result, disparate groups, including industry associations, non-profit groups, academics, and individual firms, attempted to lay out what governments and firms should report. There are many types of sustainability reporting. In this paper we focus on three of them that both governments and firms utilize. We discuss the benefits of each. We argue that while the goal of complete and perfect data is not achievable or feasible, sustainability reporting of all three types is necessary to ensure that sound public and private decisions are made.

Jan 1, 2007

By Pierre M. Gy

The final purpose of exploration is to esti- mate the grade and tonnage of the various qualities of ore contained in a given mineral deposit. This estimation cannot be directly carried out on the whole of the ore body. It usually requires four steps: Core Drilling Campaign The ore body is represented by a series of cores further divided into core sections of equal or unequal length. Core Splitting The core sections are longitudinally split into two halves: the first half is kept for various examinations and physical measurements, and stored for further reference; the second half (core sample) is used for determination of the chemical analysis. Core Sample Reduction The chemical analysis cannot be directly per- formed on the core samples. It requires the constitution of assay portions usually weighing from a few decigrams to one gram (more in precious metals assaying) and passing through a 100 or 150 mesh screen.

Jan 1, 1979

By J. M. Mutmansky, A. Wang

This paper defines the elements of a basic economic model for decision making when considering a methane drainage system for an underground coal mine. A drainage system entails significant capital and operating expense; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision making are provided for an actual mine decision.

Jan 1, 1999

By J. F. T. Agapito, C. E. Brechtel, M. E. Adam

Full-scale stopping and simulated over- cast structures were constructed in large opening (30 ft high by 55 ft wide) room and pillar excavations in an oil shale mine. The program was undertaken to develop construction techniques and to generate data on structure costs and leakage rates. Leakage rates were measured using both sulfur hexafluoride tracer gas and "brattice window" methods at varying differential pressures. The measurements were conducted before and after a full-scale face blast to characterize the effects of blasting on leakage, and blast air pressures were measured across the stoppings. The operating performance of different combinations of permanent and temporary stoppings was evaluated by developing an operating model for a two-panel oil shale mine. The operating performance for the different stopping combinations was then compared to the system cost to evaluate the overall performance.

Jan 1, 1987

By D. Tao

More than 80 million metric tons of fly ash is produced annually in the U.S. as coal combustion by-product. Fly ash can be converted to value-added products if unburned carbon is reduced to less than 2.5%. However, most of fly ash is currently landfilled as waste due to lack of efficient purification technologies to separate unburned carbon from fly ash. A rotary triboelectrostatic separator has been developed and patented recently at the University of Kentucky with unique features. Several fly ash samples have been used to understand the effects of major process parameters on the separation performance. The results show that compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator has significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range. Key words: Coal, Combustion Waste; Fly Ash; Particle charging; Separation.

Jan 1, 2008

By Frank K. Mattson

The Minerals Processing Section of Surface Combustion is currently engineering and erecting a plant designed to produce 400,000 LTPY of 95% metalized pellets from raw magnetite concentrate, This venture is the first domestic commercial facility that will manufacture pre-reduced pellets as an integral part of a process to produce steel. Surface Combustion has developed the methods that will be used. Midrex, a division of Surface Combustion's parent company, Midland-Ross, will own and operate this plant. The site is adjacent to the City of Portland, Oregon on a 15 acre hydraulically-filled area on the east bank of the Willamette River. Either filter cake or concentrates in slurry form will be purchased from Marcona in Peru, delivered to the dock facility by ocean vessels and distributed to a pond for wet storage. Reclamation from the pond will be with a conventional dredge delivering concentrate to a thickener.

Jan 1, 1968

By Louis W. Cope

INTRODUCTION Various methods for sampling placer deposits have been mentioned by Wojcik in Chapter 2. Here, a brief description and comparison of these methods will be given as related to bulk versus drill sampling. The advantages and disadvantages inherent to each will also be given. The means of sampling can be grouped into bulk or drill samples. As a generality, drill samples over a five-foot length will run from I/,, to 1 /, cubic yard, depending on the diameter of the drive shoe on the drill casing. Bulk samples can be expected to be in the range from one to many cubic yards each. SAMPLE METHODS Bulk Bulldozer-dug trenches and dozer or front-end loader pits are two methods to excavate large bulk samples. Smaller bulk samples can be obtained by digging small dimension shafts through the deposit, by hand or caisson-like drills. It is not recommended to split samples by alternate bucket-loads or by other means, as the effect of a nugget falling into one or the other fraction will seriously alter the sample.

Jan 1, 1992